SPECS - You will receive a fully-equipped Taper Sled including 2 18.5 miter bars, rigid powder-coated steel fence that won't deflect, 2 knuckle hold-down clamps, 32 honeycomb plywood sled, and Rack-It. Fits any 34 x 38 table saw miter slot.. VERSATILE TABLE SAW SLED - Whether you're looking for a repeatable angle for a set of table legs or straight-line ripping a rough board, the Taper Sled guides the workpiece past the blade using the miter slot or fence for straight line precision.. ROCK SOLID CONSTRUCTION - The 32 plywood sled is laminated with a honeycomb non-slip surface. The powder-coated steel fence won't deflect with clamp pressure. Scales are precisely 24 apart for simple rise run angle calculation.. WORKHOLDING OPTIONS - The adjustable Knuckle Clamps work with thin or thick stock. Track clamp slots are milled into the sled base. Comes with a flip stop on the fence and additional hardware to make your own. Miter bars have T-Track fittings.. AMERICAN MADE QUALITY - Like all Woodpeckers tools, each Taper Sled is designed, machined, and inspected in Strongsville, Ohio..

NEW GENERATION Add a manual switch to support three vacuum run modes Auto, Off and On. You can not only turn the vacuum onoff automatically with the power tools, but also manually turn the vacuum onoff all time according to your actual condition.. HIGH-QUALITY MATERIALS Adopt 19.7 inch UL-certified US standard 14AWG power cord which allow passage with a large current more than 30A. Durable PCABS V0 grade flame retardant material case, reduce heat during use and extend service life.. TURN ON DELAY. Load Sensing Technology. If the load connected to the 'TOOL' port exceeds 30W, the vacuum connected to the 'VAC' port will automatically delay 1s to start, which helps prevent circuit overloaded by large current if tool and vacuum power-on at the same time.. SHUT OFF DELAY Automatically delay vacuum turn-off by 7s to continue clearing the remaining airborne debris after the load connected to the 'TOOL' port has stopped. Saving time and electricity, reducing airborne toxin and work area noise that can lead many health problems.. COMPATIBILITY Support a wide range of cutting tools from handheld devices to large shop saws such as table saw, miter saw, track saw, chop saw, sander, router table, planers, shopvac, remote control outlet, automated vacuum switch, dust collection systems for woodworking and etc. Power rating should not exceed 120 VAC, 15 Amp, 60 Hz, 1875w.. WHAT YOU GET Senctrl automatic vacuum switch AVS2000, welcome guide, our worry-free 12-month warranty, and friendly customer service..

MAKES NARROW RIP CUTS SAFER Multidirectional force control the workpiece. The non-slip material at the bottom is resistant to friction and strong grip. Helps protect hands and prevent kickback while cutting.. EASY TO ASSEMBLY No frustrating assembly required. Just install the handle and side parts.. FULLY ADJUSTABLE AND PRECISION CUTTING Top sliding adjustment design, easily control the crop width. Make your table saw control down to 14 Ripping.. APPLICABILITY COMPATIBILITY Work on the table saw, Router table, Jointer, Band saw. Compatible with most tool accessories on the market.. EASY TO CLEAN When the tool gets dirty, it can be easily removed with alcohol. To keep strong friction and the best working condition..

EASY TO USEGOINGMAKE thin rip jig is easy to use. Just slide the guide into T-track miter slot of your table saw and lock it in front of the saw blade. Fits for 38 x 34 T slot and U shape slot and 14 x 38 T slot. The thin rip jig can extend to 8 inch from the center of miter slot to blade. Thin rip table saw accessories makes thin strips cut consistent.. SAFE AND FASTGOINGMAKE table saw jig thin ripping guide provides safe and fast thin strips cutting. The one way roller bearing ensures the workpiece moves forwards and does not kickback, making safe and fast repetitive narrow strip cutting with ease. You can keep the same thickness thin strips cutting consistent with this table saw thin rip jig.. PRECISE THIN RIPPINGGOINGMAKE table saw thin rip jig guide is precise and adjustale. Including mm and inch laser engraving scales. The zero clearance design is easy for set the right distance. Repeat with each strip the same size as the first for precison cutting. Set up the scale to the saw is easy. First take the bearing close to the saw blade and adjust the scale indicator to the nearest mark, then set the dimension of your strips.. HIGH QUALITYGOINGMAKE rip guide is made of high quality metal for durable, long lasting use. You can cut the thin strips as thin as 132.. WIDE APPLICATIONGOINGMAKE thin ripping guide is compatible with standard band saw, table saw and routers. Extended range is from 2-58 inch to 8 inch..

FRICTION RESISTANCE - UHMW strips are ideal as miter bars for table saw and for table saw sled runners due to their superior friction resistance, making it perfect for repetitive sliding tasks.. NO RESIDUE - UHMW plastic is slicker than wood and other plastics, leaving no residue, simplifying clean-up after use. Ideal as miter track for table saws or as a crosscut sled for table saw.. STANDARD SIZING - The 34 wide, 38 thick, 17 long UHMW strips fit most standard table saw slots. Great as a table saw guide rail or miter bar for table saw sled.. DURABILITY - UHMW plastic, known for its durability, is 10 times heavier than regular polyethylene. Its ideal for miter bars for table saws and table saw sled runners due to its strength.. USA QUALITY - Use our quality UHMW strips to create miter bars for table saw sleds and jigs. UHMW plastic works great for table saw runners. Proudly Made in the USA.

Kickback Prevention FeatherPRO virtually arrests kickback. EVA material combines with our living hinge design to pinch board against the fence and absorb kickback forces. 5x greater kickback resistance versus plastic or wood feathers.. Ultimate Feed Control EVA feathers increase the amount of surface contact on the work piece, ensuring a smooth glide across the table and superior infeed control. Substantially reduces wiggle you get with plastic feathers. Equipped with a 34-Inch miter bar that fits U and T-shapred miter slots.. Cleanest Cut EVA Feathers absorb vibration and minimize chatter for a cleaner and more precise cut. Feathers are non-marring on even the softest woods and will not damage your workpiece or saw blade.. EVA Feathers and Safety Feathers are reversible, replaceable, and interchangeable. FeatherPRO is versatile in that you can switch out between Standard and UltraFLEX Feathers. Feathers will NOT harm carbide blades or router bits in case of accidental contact. Feathers conform slightly to the wood. EVA will NOT set off Saw Stop. EVA will NOT absorb fluid as it is a closed cell material. EVA will NOT bleed color or shed material.. AnchorPRO Hardware FeatherPRO uses our patented AnchorPRO miter hardware that offers fast expansion and super strong hold in the miter slot. T Bolt is used as the expansion bolt in the miter bar. Use T Bolt for T Track mounts. Comfortable Ergonomic Knobs.. Specifications Standard EVA Feathers, Two 6 Travel slots, One 34 AnchorPRO Miter Bar mounts to 38x 34 miter slot, Two Comfortable Ergonomic Knobs, T Track Mount Two 1 12 T Bolts 516-18 thread fit 14 to 34 T Track, T Bolt Head Dimensions .090 Thick x .45W x .725L.

WORK ANYWHERE, ANYTIMEThis is an essential feature for a professional craftsman that you may need to carry the table saw to the work site at anytime. We designed the non-slip 8 inch rubber wheels to make it as easy and relaxing as traveling when carrying the table saw.. STURDY AND STABLE ENOUGHThe heavy-duty steel structure and sturdy connection fittings form a very stable frame that is so well balanced that you can completely ignore the table saw stand when you are cutting large woods because its rock-solid stability will not let you perceive the shaking.. THE BEST CHOICE FOR MINI WORKSHOPWORKESS foldable table saw has a compact structure. We also designed a convenient full folding system. lmagine how pleasant it is to put a professional table saw stand into a small space. In fact, you can do it by just pulling the release pin lever.. FITS MOST TABLE SAWSEach base plate has 14 mounting holes two plates in total, providing the flexibility to adjust between a maximum of 20-58 x 18-12 to a minimum of 6-2964 x 18-12 mounting space to flexibly match the table saw you are using.. THE PREMISE OF QUALITY AFTER-SALES SERVICE IS QUALITYWORKESS has BSCI, ISO9001, ISO14001, OHSAS18001 and other quality and safety certification. If you have any problems during use, you can contact WORKESS for the first time. We will provide professional services with engineers to offer you with quality and good after-sales service..

Premium CNC Aluminum BuildCrafted from high-grade anodized aluminum alloy with CNC precision, this thin rip jig ensures rigid stability and durability. The anti-corrosion surface eliminates wood chattering, secures workpieces firmly, and enhances cutting safetyprotecting both your project and fingers.. Universal T-Slot CompatibilityFits standard 38 x 34 and 14 x 38 T-track tables not U-slot. Works seamlessly with most table saws, router tables, and band saws, making it a versatile addition to any woodworking shop.. Wide Secure Adjustable RangeFeatures an extended telescoping range 2 to 8-12 with dual imperialmetric scales for precise measurements. The reinforced T-bar design locks firmly in place, preventing slippage during operation.. Laser-Sharp 132 PrecisionEngineered for accuracy down to 132, this jig delivers flawless, repeatable cutsreducing material waste and ensuring professional-grade results for fine woodworking and cabinetry.. Tool-Free Quick AdjustmentNo complicated setup The intuitive adjustment mechanism lets you change cutting widths quickly, boosting efficiency for high-volume or multi-size cutting tasks..

INCLUDES 12 universal t tracks, 19 HDPE miter bars, 3 star knob, hex head bolt, flat head wood screws, instruction sheet. FUNCTION Provides you with the table saw sled hardware needed to cut boards to precise lengths while preventing measuring and cutting errors. 100 SAFE Makes crosscutting safer, more efficient and convenient, while avoiding risking your limb when crosscutting smaller pieces with a crosscut sled specifically calibrated with your table saw. PREMIUM QUALITY The t-tracks included in this kit are made of solid extruded aluminum and the miter bars are crafted with high durability, high stability HDPE high density polyethylene. DIMENSIONS Universal T-Tracks 12 long HDPE bars 19long 34 x 38 Threaded Star Knob 14-20 x 1-12 Hex Head Bolt 14-20 x 1-12 Flat Head Wood Screws, 6 x .

Upgraded Multifunction Miter GaugePrecision Miter Gaugeis made of high quality steel plate for excellent performance for your table saw cross cutting needs. Aluminum Miter fence is equally well thought out with its 45 degree ends for workpiece support and its can to mounted to more miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw.. Precision Miter GaugePrecise angle cutting miter gauge with thick, adjustable, solid aluminum head.The 200 thick, adjustable, solid aluminum head is machined with 120 positive stop holes.It features 27 Angle Stops, 5-Degree Increments, laser marking technology is friction-resistance to ensure accuracy. Table Saw Fence wScaleThe surface of table saw miter gauge fence is come with metric scale.Table saw miter gauge fence with tenoning function and the steel miter bar is equipped with a metal. Precision miter gauge can tenon requirements of the board can be made according to the required size.. Precision Mirco Adjustable Flip StopThe fence comes with a flip stop can be used with most any miter gauge with its off-set mounting track on the back of the fence. Universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted and non T-slotted miter slots, and adjustable expansion discs. Premium Quality Worry-free purchaseIncludes 1 table saw miter gauge, 1multi-track miter fence, 1t-track flip stop. If you are not completely satisfied with the miter gauge, we will provide you with the perfect solution..

EXCEPTIONAL ACCURACY FOR TABLE SAWS Elevate your woodworking precision with DFM Tool Works' saw blade depth gauge. Achieve meticulous heights under 164 inch, essential for exact table saw calibration. This tool guarantees precision in every cut, ensuring unmatched craftsmanship.. ADVANCED VERSATILITY FOR TABLE SAW ALIGNMENT The DFM height gauge offers 14 steps in 18 increments, ideal for diverse table saw gauge settings. With its sturdy 14 thickness, it's perfect for precise table saw alignment, enhancing your woodworking with exact and adaptable measurements.. ROUTER TABLE COMPATIBILITY FOR SMOOTH OPERATIONS Designed for optimal router table efficiency, this gauge from DFM Tool Works seamlessly adapts to various router bit sizes, making it a vital table saw calibration tool. It ensures smooth and precise adjustments, essential for quality woodworking.. DURABLE ALUMINUM FOR LONG-LASTING USE Constructed from robust 14 aluminum with a clear blue anodized finish, this table saw alignment gauge offers enduring strength and ease of reading. Its durable design ensures longevity and reliability for all your woodworking projects.. DFM PRECISION FOR PROFESSIONAL RESULTS This height gauge by DFM Tool Works is a testament to high-quality craftsmanship. Ideal as a table saw calibration tool, it delivers unparalleled precision for professional woodworking results. Trust DFM for accuracy and excellence in every project..

Once installed, you can easily adjust and calibrate the NoPlay miter bar from above on your sled NoPlay Miter Bars are designed to be adjusted to fit your table saw, router table or band saw miter slot. Simply set it, test it and make any needed adjustments for the ideal fit.. The one of a kind Expandable Glides Patent Pending are designed expand or contract as you tighten or loosen the center screw. Rotating clockwise expands the Expandable Glide while rotating the counter-clockwise contractsbrings the Expandable Guide back toward the miter bar.. The NoPlay Miter bar is designed for use in any standard 34 x 38 miter slot. Made from aluminum, the bar will not bow or warp like some plastic or wood bars do. Will work in many router table and band saw slots. Excellent for crosscut sleds on your table saw. Each miter bar comes with a transparent stick-on template making installation a breeze Can be mounted using the included wood screws that secure the bar through the bottom of your sled. Alternatively you can use the included machine screws to mount the bars through the top of your sled.. Will not work in 58 miter slots like those found on big box store brand table saws. Please measure your slot width and height before making your purchase and make sure it falls into the 34 x 38 dimensions..

400 LB CAPACITY The Bora Portamate Mobile Base PM-1000 has a weight capacity at 400lbs. 181 kg. Its universal strength makes it ideal to move square or rectangle equipment and heavy tools around your shop or garage. MOUNT MOVE EASILY Make large machinery such as table saws and bandsaws, woodworking equipment, power tools, planers, jointers, shapers, and spindle sanders movable with ease with this strong base. ADJUSTABLE SIZE Adjusts from 12 x 12 inches to 32 x 32 inches square or up to 17 x 48 inches rectangle. The stand is adjustable in 1-inch increments to fit a wide variety of machines. EASY GLIDE LOCKING LEVERS The easy to use foot-operated locking levers lock the steel mobile base firmly into place. When its time to get moving, the 3 inch hard rubber wheels provide a smooth glide. LOW PROFILE This mobile base lifts your machine height by less than 1 inch, adding only a small increase to your working height while allowing your equipment to be completely mobile and moved around as needed.

Coping Sled For Router Table If you're building cope-and-stick doors and drawer fronts, our new rail coping wood sled will be an indispensable helpmate. The Rockler rail coping jig has taller round handles that allow a firm, comfortable grip from any angle of approach.. Smooth-Running Sled With its smooth-sliding phenolic base, and sturdy toggle clamp holding your stock firmly against the router fence, your rails will travel unwaveringly past the cutter for the cleanest, squarest cuts you can imagine.. Keeps Your Hands Safe Particularly with drawer fronts, which sometimes use very narrow rails, the rail guide coping sled prevents parts from dipping in too deep and keeps your hands safely out of harm's way.. Prevent End grain Blowout A sacrificial block can be attached to the fence to prevent end grain blowout, while an abrasive strip prevents the workpiece from wandering.. Whats Included Our router table woodworking kit includes a Sled Base, Fixed Fence, Adjustable Fence, Lever Clamp, Sacrificial Piece, Front Handle, Rear Handle, 2 1'' Round Knob, 4-Star Knob, 2 Large Washers, 4 Small Washers, 2 Spacers, 516''-18 TPI x 1'' T-Slot Bolt, 516''-18 TPI x 1-1 2'' T-Slot Bolt, 3 516''-18 TPI x 2-1 2'' T-Slot Bolt, 4 Cap Nut, 4 1-3 4'' Mounting Screws, 2 8 x 1-3 4'' Wood Screws, Abrasive Strip, Manual.

Premium MaterialThe table saw sled is made of UHMWPE material, durable, and long-lasting. It can provide stability and reliability during each cutting process.. Pre-Drill HolesWe reserve 5 screw holes on each plastic strip and provide matching 25 pcs screws, Ensure that the material does not expand when inserting the screw.. Size InformationThe crosscut sled wide is 34'',thick is 38'', length is 17'', suitable for most standard desktop saw slots.. 100 SafeGreat for cross-cut sleds, makes crosscutting safer, more efficient, and convenient. At the same time, it avoids the risk of endangering limbs when using a cross-cutting pulley specially calibrated with a desktop saw to cut small pieces.. Smooth Sliding SurfaceThe table saw sled surface is very smooth, without burrs or sawdust-like wood, and easy to clean. Smooth design ensures low friction sliding, allowing seamless operation and easy and precise cross-cutting..

Rocklers Taper Straight Line Jig The taper drill jig allows you to make tapered cuts quickly, easily, and accurately at your table saw. With the miter bar removed, this wood working jig also doubles as a stable, straight-line ripping jig.. Easy To Fit This straight-line hole jig fits snug in any standard 38 x 34 miter slot and features a large, ergonomic handle for smooth push-action performance throughout the cut. The guidance booklet in our jig table saw is available so you can make it your very own.. Multipurpose Drill Jig For Angled Holes With a simple indexed angle setting system, heavy-duty hold-down clamps, and a smooth sliding design, the table saw jig makes tapered cuts fast, easy, and more precise. Our jig tools are perfect for chair legs, table legs, and more.. Easy To Setup In tapering mode, these woodworking tools and accessories are intended for use in the miter slot to the right of the blade. On many saws, your initial cut will remove a narrow piece of the tablesaw jigs base to create zero-clearance support. Where To Work These wood working tools works with table saws on which the left edge of the right miter slot is 3-34 to 4-38 from the blade or 5 to 5-58 from the blade..

Sturdy and DurableTable saw sled is made of UHMW linear polyethylene material, sturdy and durable, not easy to deform and wear. The surface is smooth, burr-free, and easy to clean.. Package IncludedYou will receive 2 pcs 17-inch long table saw runners, 34 inch wide and 38 inch thickeach with 5 pre-drilled holes, and 12 screws for easy installation. Suitable for most standard table saw slots.. More Resistant To FrictionCrosscut sled material has a low-density molecular structure, does not expand or contract with temperature changes, has strong impact resistance, high stability, and low friction, ideal for table saws that repeatedly slide.. Safe and EfficientMiter bars for table saws are ideal for cross-cutting, repetitive length cutting, and small cuts. Meet various cutting needs, making the cutting process safer, more convenient, and efficient.. Wide ApplicationTable saw sled kit is perfect for woodworking, making table saw sleds, woodworking jigs, and fixtures for table saws, band saws, or milling machines. Easy to operate, ideal choice for a workshop tool series..

Sturdy DurableTable saw sled is made of UHMW linear polyethylene material, sturdy and durable, not easy to deform and wear. The surface is smooth, burr-free, and easy to clean.. Package IncludedYou will receive 4 pcs 17-inch long table saw runners, 34 inch wide and 38 inch thickeach with 5 pre-drilled holes, and 25 screws for easy installation. Suitable for most standard table saw slots.. More Resistant To FrictionCrosscut sled material has a low-density molecular structure, does not expand or contract with temperature changes, has strong impact resistance, high stability, and low friction, ideal for table saws that repeatedly slide.. Safe EfficientMiter bars for table saws are ideal for cross-cutting, repetitive length cutting, and small cuts. Meet various cutting needs, making the cutting process safer, more convenient, and efficient.. Wide ApplicationTable saw sled kit is perfect for woodworking, making table saw sleds, woodworking jigs, and fixtures for table saws, band saws, or milling machines. Easy to operate, ideal choice for a workshop tool series..

Precise 45 Degree Cut This table saw miter sled provides precise positioning for wooden , ensuring precise cutting of 45 degrees every time.. Wide Usage This 45 degree miter sled is very suitable for cutting photo frames or any products that require precise cutting for 90 degree splicing.. Standard Slot The through hole in the base allow you to securely clamp strip at table level, this table saw miter sled is suitable for standard 38 inch x 34 inch miter slots.. Premium Material The table saw miter sled is made from premium PP material, sturdy and long lasting, compact and portable, convenient to carry.. Versatile Application The miter sled is suitable for installing anti collision strips, skirting line, corner wood floor, and more projects..

Crosscut Sled Kit Package includes 2 pcs 12-inch aluminum T-tracks, 2 pcs 17-inch UHMW miter bars for table saw sled, 1 star knob and bolt, 1 round washer, and 15 screws. Compatible with most standard table saw slots Note wooden sled are not included in the package.. Sturdy Material T-tracks are made of solid aluminum, and the table saw miter sled are made of UHMW linear polyethylene, which is sturdy and reliable, smooth surface without burrs, and can be reused for a long time.. UHMW Miter Bars Very suitable for use as a crosscut sled guide and table saw sled runners, with low friction and stability during use, and will not expand or shrink due to environmental changes.. Precise and Efficient Crosscut sled for table saw help to cut accurately, meet various cutting needs, reduce measurement and cutting errors, and help woodworkers improve safety and efficiency.. Wide Application Table saw sled kit is perfect for crosscutting, repeated length cutting and small cutting, stabilizing the workpiece, and the included knob and bolt can be used as a stop block to achieve consistent cutting without frequent adjustment of measurements..

ACCURATEFeatures easy-to-read precision laser engraved scales, protractor allows direct angle reading to the miter saw. Perfect for crown molding, trim work, and a variety of other carpentry applications.. O BODY DESIGNSaker Miter Saw Protractor is of O shape design during operation and ensures smooth precise read on insideoutside corners, Crafted from precision CNC-machined aluminum alloy.. EASY TO CARRY Saker Miter Saw Protractor is made of lightweight aluminum alloy, which has great corrosion and wear resistance, extending the lifespan. Also, its small size and lightweight material makes it easy to carry.. WIDE APPLICATION Whether you are a professional or not, Saker Miter Saw Protractor is excellent for you. It is suitable for crown molding, miter cuts, carpentry, plumbing, metalworking and more.. ServiceWe Are Confident In the Quality of the Product. In the Process of Daily Use, If the Product Has Quality Problems or Have any Questions About the Product, Please Feel Free To Contact Us, We Are Always There..

FITS 34-INCH MITER SLOTS WHICH IS THE MOST COMMON, STANDARD SIZE - this will not work on small table saws with 58-inch miter slots. Please measure your miter slot at the table surface If yours is 58-inch wide, please search for ASIN B09M2M53YK to purchase the 58-inch bundle package.. ONE-HANDED OPERATION FOR QUICK ADJUSTMENTS The Hedgehog spiral featherboard has a simplified design that features only one knob for quick, easy, and seamless adjustments. This single pivot point streamlines woodworking while maximizing your productivity.. IMPROVE THE QUALITY OF YOUR WORK This premium, single pivot point featherboard will guarantee high quality output every single time. Its perfect for hobbyists and professionals looking to create wooden masterpieces.. YOU'LL PRODUCE SMOOTHER AND CLEANER CUTS The precision and accuracy in this premium featherboard ensures that you can hold the wood tight against the fence which results in cleaner, smoother cuts. Dramatically improve the quality of your woodworking production.. THE HEDGEHOG FEATHERBOARD REDUCES KICKBACK AND OTHER DANGERS FOR ENHANCED SAFETY Thanks to the unique spiral design of this featherboard, kickback is greatly reduced for superior protection when ripping on your table saw.. THE HEDGEHOG FEATHERBOARD IS DESIGNED IN THE USA by the owner of The Hedgehog brand and is protected by two US patents..

Saw Blade Height Gauge crafted from quality aluminum, this digital height gauge for table saws and router ensures precise height adjustments Setup Table Saws blade height From 18 to 2 in increments of 18 Perfect for woodworking enthusiasts seeking accuracy and consistency in their cuts, it effortlessly streamlines the woodworking process. Precise Table Saw Gauge crafted for accuracy, this router table miter gauge offers clear and concise readings, ensuring precise measurements each time The router bit height gauge has two measurement scales, the left in 18 inch and the right in 14 inch It is 14 inch thick and stands on its own The 18-1 side is designed for table saws, while the 18-2 sides are tailored for routers and router tables. Sturdy and Solid the sturdy construction of the table saw height gauge is attributed to its aluminum material, which ensures durability and robustness for long time use Its sturdy construction and precise measurement capabilities make it a reliable tool for woodworking applications. Easy to Carry and Store the digital woodworking table saw height gauge features a compact size, making it convenient for portability, while the presence of a small hole on the left side allows for easy hanging when not in use This makes it a versatile tool that can be stored and utilized with ease. Easy of Use this table saw depth height gauge simplifies the process of adjusting the height of the saw blade, making the workflow for a variety of cutting tasks easy and fast Its dependable performance makes it a good addition to any workshop or professional setting, offering a nice experience for professional woodworker or a DIY enthusiast.

Making repetitive cuts on your table saw is a pretty straight forward process. Set your fence and feed each stock piece through the blade to achieve the same size each and every time. What if you need a series of narrow cuts that are about an 2 inches or less in width Doing this can get tricky since you cant get your hands safely between the blade and the fence. You could always reverse measure and keep the off fall piece, but without a guide of some sort that can be inaccurate.. The Thin Rip Jig acts kind of like a third hand behind the blade or cutter. With the saw unplugged simply measure from the outside of of the blade toward the tip of the guide roller Thin Rip Jig for the width cut you want to make. Once set, secure the Thin Rip Jig simply by rotating the large, easy to grip star shaped knob. After your first cut, reset your stock behind the blade and slide the fence over so your stock piece is touching the guide roller on the Thin Rip Jig. Lock the fence.. Making your thin rip cuts in this fashion allows you to cut wider boards down without getting your fingers in harms way by keep them away from the blade or cutter.The Thin Rip works much like a feather except that it doesnt exert spring like pressure against the board. This means it can be used to make accurate, repetitive cuts since its essentially just holding its spot once it is secured.. The Thin Rip Jig has a roller guide bearing on the tip to make feeding your stock through an easy and smooth moving process. The free rotating bearing is made from high quality materials for extended workshop use. The jig fits directly into most any standard 38 x 34 miter slot. The body is made from a solid piece of aluminum and is adjustable inward and outward from your fence depending on the width of your stock.. The jig can be used on other workshop machinery like router tables with fences and band saws for re-saw applications. In certain cases, when working with larger or longer stock on table saws or router tables, we recommend using two thin rip jigs behind the blade or cutter for extra stability when feeding your stock through..

Multi-Angle Adjustment for Diverse Woodworking Needs With an angle adjustment range of 55 to 93, it can be arbitrarily set according to different DIY woodworking scenarios such as mortise and tenon processing, engraving, and cutting. It flexibly handles complex processes like bevel cutting and splicing without the need for additional tool replacement, allowing one table saw router table joinery sled to meet the needs of multiple processes. Balanced Fine Adjustment and Stable Performance Equipped with a precision adjustment knob, it can accurately control the distance from the cutter head, improving the operational precision during cutting and engraving while avoiding processing errors. The main body is made of aluminum alloy, which has strong load-bearing capacity and can remain stable even under heavy-load use, ensuring long-term reliable operation. Flexible Clamping and Positioning Design The middle screw rod has an adjustment range of 20mm, and the rear clamp has a clamping range of 5-40mm. It can adapt to workpieces of different sizes and shapes by adjusting parameters such as width and position. The base plate is equipped with adjustable positioning options, enabling quick alignment of workpieces, reducing positioning time, and making the processing flow smoother. Complete Accessories and Easy Installation The package includes an adjustable base, side panels, 2 non-slip handles, left and right side panel connectors, a fixed clamp with green rubber pad, as well as a full set of installation tools such as 2.5mm3mm4mm hex socket wrenches, an 8mm open-end wrench, and anti-loosening screws. No additional purchase is required, and assembly can be completed by following the steps. Ergonomic Design Equipped with a vertical push handle, the non-slip texture on the surface ensures a firm grip and prevents slipping when applying pressure. During operation, it can stably control the movement of the workpiece, reducing the risk caused by hand deviation, and balancing efficient processing and operational convenience.

24 Aluminum Miter Bar The Rockler miter track bar allows you to set up your jigs for smooth-sliding action on table saws, router tables, bandsaws, and more These aluminum table saw miter bars won't warp, swell or shrink like wooden runners.. Adjustment Screws This solid aluminum miter bar has nylon set screws in the miter bar that adjust in or out for a perfect fit in any standard 34 x 38 miter slot.. Great For Our miter slider bar is great for shop-made crosscut jigs, cutoff tables, taper jigs, and more. Available individually in 18, 24, and 36 lengths.. Easy Assemble Our miter bar slider makes it very easy to construct that ideal jig without dealing with the wood runners and the swelling issues. This table saw miter bar has 14-20 threaded holes for easy attachment. Note Mounting screws are NOT included because the length of screw needed depends on the thickness of your material. The miter bars are tapped for 14-20 machine screws, which provide extremely secure attachment, and also allow attachment to thin material 12'' and even thinner. This can help maintain maximum depth of cut on crosscut sleds.. Extremely Durable Our miter bars for the table saw are made of high-quality aluminum alloy that will be strong and reliable for several years..

Premium MaterialThe table saw sled is made of UHMWPE material, and the T-track is made of solid extruded aluminum, durable, and long-lasting. It can provide stability and reliability during each cutting process. Size InformationThe crosscut sled wide is 34'',thick is 38'', length is 17'', and the universal T-track wide is 0.75'',length is 12''Please refer to Figure 2 for specific dimensions. 100 SafeGreat for cross-cut sleds, it makes crosscutting safer, more efficient, and convenient. At the same time, it avoids the risk of endangering limbs when using a cross-cutting pulley specially calibrated with a desktop saw to cut small pieces. Smooth Sliding SurfaceThe table saw sled surface is very smooth, without burrs or sawdust-like wood, and easy to clean. Smooth design ensures low friction sliding, allowing seamless operation and easy and precise cross-cutting. Table Saw Sled KitYou will receive 2 Aluminum T-Tracks, 2 UHMW miter bars for the table saw, 1-star knob and bolt, 10 Screws, and 1 round washer, the crosscut sled kit is suitable for most standard desktop saw slots.

ONE-TOUCH CALIBRATION FOR PRECISION Build table saw sleds quickly and boost woodworking accuracy with the ZEROPLAY Miter Bars Instantly fill the width of miter slotsno side-to-side play, slop, or seasonal warping. FAST TOP-DOWN INSTALLATION These table saw accessories secure miter bars from above to keep sleds, jigs, and fixtures perfectly square for consistently accurate cuts. UNIVERSAL FIT FOR 34' MITER SLOTS These miter bars for table saws are designed to be compatible with virtually all standard 34 x 38 miter slots including ShopSmith, and work with both T-shape and U-shape miter slots. MULTI-BAR FLEXIBILITY Includes two 9.25 ZEROPLAY miter bars, two ZEROPLAY miter stops, and all hardwarebuild long sleds and jigs for larger, safer crosscuts. COMPLETE BUILD KIT AND PLANS Everything needed for precision projectshardware, stops, carriage bolts, thumb knobs, and crosscut jig plans included for easy setup.

Product MaterialThis Crosscut Sled is made of ultra-high molecular weight polyethylene, which has the characteristics of super wear resistance, self-lubrication, high strength, stable chemical properties, and strong anti-aging performance. Product DesignThe Miter Slot Runners are 17 43mm long, 34 19mm wide, and 38 9.8mm thick. Each rod has 5 precisely sized pre-drilled and countersunk holes to ensure that the screws can be inserted without rubbing against other contact surfaces. Product FeaturesThis UHMW Miter Bar is easy to clean and will not expand or contract like wood. It does not absorb moisture and will not swell with exposure to air. It is ideal for the crosscut slide of a table saw due to its low coefficient of friction, making it an ideal choice for sleds that need to slide repeatedly. Versatile ApplicationThe Crosscut Sled can be connected to most woodworking workpieces and can be used to build various fixtures on the table saw table, such as miter sledges, making crosscuts safer and more efficient. It is usually suitable for radial arm saws, benchtops, drill presses and various other engineering equipment. Simple design, powerful function, can well assist various cutting tasks. Package IncludesThe package includes two 34 x 38 x 17 Crosscut Miter Bars and some self-tapping screws.If there is any problem with the item you received, please contact us for a replacement. We will try our best to provide you with satisfactory..

Designed for versatility, the adjustment angle can be set anywhere between 55 and 93 to support a variety of woodworking needs. It flexibly handles complex processes like bevel cutting and splicing without the need for additional tool replacement, allowing one table saw router table joinery sled to meet the needs of multiple processes. Fine-Tuning Mechanism Equipped with precision knobs to accurately adjust the distance from the blade head for enhanced control during cuts, while avoiding processing errors. Robust Aluminum Alloy Material Made from high-grade aluminum alloy for long-lasting stability and reliable performance under heavy use. Flexible Base Plate Design The base plate features adjustable positioning options for greater alignment accuracy and a smoother workflow. Ergonomic Push Handle Equipped with a vertical push handle, the non-slip texture on the surface ensures a firm grip and prevents slipping when applying pressure. During operation, it can stably control the movement of the workpiece, reducing the risk caused by hand deviation, and balancing efficient processing and operational convenience.

This Miter Bar is made of high-quality anodized aluminum, it is of strong strength and long durability, good insulation performance and long service life.. The T-Slot Track Bar is 300mm 11.8in long, 19mm 0.75in wide, 9.5mm 0.37in thick, and the diameter of the two pulleys is 22.8mm 0.9in.. The miter gauge is designed with removable retaining disc at both ends, can be installed or removed from both ends as needed to slide in the slot, it can prevent accidental lifting during sliding. This is the best choice for the carpentry daily work.. Can be used to build various fixtures on table saw tables, such as miter sledges. Commonly used on radial saws, countertops, drill presses, and a variety of other construction equipment. Beautifully designed, easy to use and powerful.. Easy to use Adjust for perfect sliding action in any standard miter gauge slot with just a twist of the wrist. Locks securely in any standard miter gauge slot with another twist of the wrist.

THE ORIGINAL DUBBY SLED From standard 4 sided panel cutting to the absolutely stunning heptagon frame you will be completely accurate with the angles on your mitered projects with the Dubby Sled. The Dubby will allow you to make perfect cuts the first time you do them and keep your creative juices flowing with idea after idea. It is ideal for making frames but it also works very well for the cutting of tiny pieces while keeping your fingers out of harms way.. WORKING WITH LARGE PANELS The Dubby has the capacity to crosscut panels up to 24 wide x 52 long, and allows you to do them safely. Since the panels dont make contact with the table saw top, walking of the material is virtually eliminated. This will allow you to cut perfectly square panels for your furniture and cabinet making projects quickly, easily and accurately.. WORKING WITH ANGLES The Dubby angle scale is the simplest, most accurate and easiest to read scale available. Being about 15-20 times more accurate than the average miter gauge, the scale has pre-determined lines for any shape from 4 to 16 sides you want to cut. This means no calculations, no hassles, and best of all, no test cuts for perfect results. WORKING WITH SMALL PIECES- No miter gauge on the market can offer you the margin of safety provided by the Dubby Sled. The versatile hold-down clamp included with every Dubby will give you an extremely safe way to cut small pieces, and will easily pivot out of the way when you dont need it. With 35lbs. of hold down pressure, the clamp will hold small pieces all the while keeping your hands and fingers out of harms way.. WILL THE DUBBY FIT YOUR SAW The Dubby sled is compatible with most cabinet and contractor table saws. However, your table saw should fall within the following specs for a proper fit. The Miter Slot should be a wide x 38 deep slot. Your saw must measure at least 27 from the front of the saw to the back. The miter slot must be 4 to 5 from the installed table saw blade. PLEASE NOTE that the Dubby WILL NOT work on most JOBSITE style table saws. Please measure your saw before ordering..

High Quality MaterialThin rip jig table saw jig guide is crafted from CNC-machined Anodized Aluminum alloy, anodized surface, metal rigid structure, strong and stable, hold the workpiece firmly and eliminate wood chattering, ensure cutting quality and avoid your fingers being damaged.. Confirm The Compatible SizeSaker thin rip jig equipped with sliders and T-bolts, ONLY FIT 38 x 34 inch T-slot and 14 x 38 inch T-slot track, can work with most standard table saw, router table and band saw. NOT FIT U SLOT . Wide Range,Secure PositioningSaker thin rip jig guide upgraded with an extended telescopic range to 2inches to 8-12 inches, equipped with imperial and metric scale markings, and a T-shaped structure for more secure positioning.. Precise PositioningThe Saker Thin Rip Jig Table Saw Jig Guide allows you to position yourself quickly and better safely to help you make cuts with your table saw.The table saw jig is meticulously designed with a measurement precision of 132. Ideal for woodworkers who require consistent and precise cuts, this tool ensures each cut meets the desired size and accuracy, reducing material waste and enhancing overall project efficiency and quality.. Easy AdjustmentThin rip table saw jig Equipped with a simple adjustment mechanism, it allows for quick setup and adjustment of cutting width, enhancing work efficiency significantly, suitable for various cutting needs..

Function ForoGore Table Saw Sled Kit design for crosscutting, repeat length cutting, and small cuts, stabilizing workpieces Improve cutting accuracy, prevent measuring and cutting errors. High Quality T-track The t-tracks are made of solid extruded aluminum. Each track is cut to length for the perfect sub-fence on the crosscut sled. Safety Design The crosscut sled for table saw makes crosscutting safer, more efficient and convenient, while avoiding risking your limb when crosscutting smaller pieces with a crosscut sled specifically calibrated with your table saw. UHMW Bar The 34'' x 38'' UHMW 17 long bar better than wood as runners for crosscut sledsReduce friction Prevnet to expand or contract like wood does during drastic weather changes Not warry about leaving any residue, dust or shavings behind like wooden bars tend to do Note The bars DO NOT fit RYOBI table saw track slots. Package Include 2 UHMW bars 34'' by 38'' , 2 T tracks, 1 star knob and bolt, screws.

If you own a table saw, you probably have come across a situation or two where you need to make smaller cuts or make cross cuts. You may also have had the need to make repetitive cuts of the same length. Making small cuts, cross cuts and repetitive length cuts is where table saw crosscut sleds excel. Crosscut sleds help stabilize the work piece and are very accurate since they are essentially calibrated to your saw during the sled building process.. Some time ago we noticed a lot of companies had UHMW bars available for purchase. While we as a woodworking company know exactly what they are used for, many novice or non-woodworkers do not. Thats when we decided to create this package with pre-cut UHMW bars, pre-cut aluminum track, a knob and bolt and an easy to understand how to guide booklet so you can create your very own, custom crosscut sled to fit your table saw. UHMW bars are most commonly used as runners for crosscut sleds since they dont produce as much friction as wood does. Another advantage is that UHMW wont expand or contract like wood does during drastic weather changes. Each bar is approximately 34 x 38 which fits most standard table saw slots. UHMW bars are also slick and wont leave any residue, dust or shavings behind like wooden bars tend to do.. The tracks that are included in this kit are made from solid extruded aluminum and are Made in the USA. Each track is cut to length for the perfect sub-fence on the crosscut sled. The included knob and bolt is for making a simple stop block which when finished, can slide the length of either track along the sub-fence. The stop block will allow you to make repetitive cuts without having to constantly move and measure the fence distance each time you make a cut.. We have also included a full color and detailed how to guide book to help you with the crosscut sled building process. Each kit comes with 2 each 19 long by 34 by 38 UHMW bars, 2 each 12 long mini tracks, 1 each knob, 1 each 14 by 20 tpi bolt and a how to build your own crosscut sled guide book. Make your crosscut sled to the size you want or need for your table saw and your specific cutting needs. Please Note, the bars do NOT FIT RYOBI table saw track slots..

PRECISION AT YOUR FINGERTIPS - Woodpeckers StealthStop Miter Sled offers unparalleled accuracy and versatility in a cost-effective package. Forget the hassle of making your own sled our sled boasts an easily adjustable miter bar and a back fence that's always perfectly square.. EFFORTLESS ADJUSTMENTS - The StealthStop Miter Sled's miter bar features a unique design with leaf springs that adapt to worn or poorly-sized miter slots, ensuring a snug fit on any table saw. Plus, all adjustments are made from above the table, making it a breeze to align the sled with your saw blade.. COMPACT, DURABLE, AND LOW-FRICTION - Crafted from 12 Baltic Birch plywood with a black micro-dot laminate, our sled is not only sturdy but also low-friction, allowing for smooth cross-cuts. Its compact 15 x 15 size offers up to 29 of support with an optional extension, ensuring you're covered for various project sizes.. FLIP STOPS FOR INSTANT READINESS - The StealthStop retractable flip stops are always at the ready, and they flip out instantly when you need them. With minimal backlash and sideways flipping action, they stay securely in place for precise cuts without the worry of interference.. PROTRACTOR PERFECTION - The StealthStop Miter Sled boasts a protractor with positive stops for 3, 4, 5, 6, 8, and 12-sided objects, ensuring accurate and repeatable angled cuts. Its unique tapered index pin eliminates any wiggle room and guarantees perfect centering, even after thousands of cycles. Crafted with precision in our Ohio facility, the StealthStop Miter Sled is engineered to meet the highest standards, making it a must-have tool for your woodworking projects..

Ultimate Material Control Add Matchfit Dovetail Clamps to secure material when cutting tricky angles. For instance, tapered legs are typically cut at a deep angle, and need to be secured very close to the blade. You dont want your hands anywhere near that cut. Dovetail Clamps secure the material for you, keeping your hands safely clear of the blade. Fit Any Miter Slot ZeroPlay Miter Bars will fit any standard 34 x 38 inches miter slot that measures between 0.73 inches and 0.79 inches wide and is at least 516 inches deep. Compatible miter tracks include but are not exclusive to ShopSmith, SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks. Speed and Precision The ZeroPlay Miter Bar that guides the 360 sled is adjusted to your saw from above, filling the miter slot fully from edge to edge. It has never been easier to get the perfect fit smooth movement along the table with zero play side to side. 360 Degrees of Adjustability The unique grid layout of dovetail grooves allows you to set your fence at any angle, and lock it in place with the included MatchFit Dovetail Hardware. No matter the angle of your cut, the ZeroPlay Miter Bar keeps the sled running parallel to the blade at all times. Everything But The Wood This sled is incredibly easy to build. All you need is some plywood, a 12-Inch 14-degree dovetail router bit, and about an hour. The package includes easy-to-follow plans.

Table Saw Sled Kit You will receive 2 UHMW miter bars for table saw 17 in, 2 universal T-tracks 12 in, 1 star knob and bolt, 1 round washer, and 15 screws, fitting most standard table saw slots Note wooden sled not include.. Well made T-tracks are made of solid extruded aluminum and the table saw runners are made of UHMW linear polyethylene, durability, and smooth, surface burrs-free.. Safe and Efficient The crosscut sled for table saw aids in precise cutting, meeting various cutting needs, prevents measurement and cutting errors, and enhances safety and efficiency.. Low Friction UHMW miter bars for table saw are ideal for use as crosscut sled guide rails, and have low friction and stability without expansion or contraction due to environmental changes.. Function Table saw sled kit is perfect for crosscutting, repeat length cutting, and small cuts, stabilizing workpieces, included knobs and bolts can be used as simple stop blocks for consistent cuts without frequent adjustments to measure fence distance..

PRECISION STABILITY - If you own a table saw, you likely need to make smaller cuts or repetitive cuts. A crosscut sled for a table saw enhances precision and stability, ensuring accurate cuts. A table saw sled kit or crosscut sled kit can make small and cross cuts easier, assisting with consistent length cuts during your projects.. ADJUSTABLE RAILS - Comes complete with a stop block and adjustable rails. The adjustable aluminum tracks fit most table saws with standard 34 x 38 miter slots. This crosscut sled kit ensures table saw precision, making small cuts not only effortless, but also safe. DOES NOT FIT RYOBI TABLE SAW SLOTS . COMPOSITE STOP BLOCK - The crosscut table saw sled features a composite stop block that won't damage the saw blade upon contact. It can be positioned on either side of the sled, making it perfect for achieving consistent cut lengths repeatedly. The sled measures approximately 18 long by 16 wide.. CROSSCUT PANELS UP TO 13-12 WIDE - This cross cut sled for a table saw can handle both small pieces and panels up to 13-12 wide, delivering straight line crosscuts that miter saws can't achieve. It's the ideal crosscut sled kit for a variety of projects, providing a reliable mid-length crosscut solution.. MEASURE YOUR SLOTS BEFORE ORDERING - Features adjustable aluminum tracks that fit most table saws with standard 34 x 38 miter slots. Please note that these tracks are incompatible with Ryobi and some other models. Measure your slots before ordering to ensure a proper fit for your crosscut sled.. DOES NOT FIT RYOBI TABLE SAW SLOTS .

Value Table Saw Sled Kit The package includes 2 Aluminum T-Tracks, 2 UHMW Miter Bars, 2 M6 and M8 T-Tracks, 2 Knobs and Bolts, and 16 Screws. Compatible with most standard table saw slots for versatile use. Versatile Cutting Solutions Perfect for crosscutting, repeat length cutting, and small cuts. The included knobs and bolts function as stop blocks for consistent cuts without frequent measurements. Low Friction Miter Bars Ideal for crosscut sled guide rails, these UHMW bars offer stability with minimal friction, unaffected by environmental change to expand or contract. Safe and Efficient This crosscut sled is designed for accurate cuts, reducing measurement and cutting errors, enhancing both safety and efficiency for your woodworking. Seamless Operation The table saw sled's smooth surface ensures low friction sliding and is easy to clean, providing a burr-free and sawdust-free cutting experience for precise cross-cutting.

Accurate Woodworking Crosscuts and Miter CutsGOINGMAKE miter gauge for table saw is perfect for repeat woodworking angle cuts with 11 positive angle stops. Allowing you to easily setup and cut angles for 90,60,45,30,22.5,15,0,-60,-45,-30,-22.5,-15. Easy to adjust and lock angles securely in place with engineering plastic locking handle and metal angle stops. You can also cutting other angles from -60to 60 with the clear laser scales. GOINGMAKE compact miter gauge is a must have table saw accessories for woodworking angle cuts.. Compact Size for Easy and Precision CutsGOINGMAKE compact table saw miter is perfect for compact portable jobsite table saw with our 360mm miter bar and 360mm precision miter gauge fence with clear laser mm and inch scales.The compact size and solid body is easy to use and also provides accuracy and stability. Easy to storage, carry and operate. It also a perfect upgrade for most table saw.. Multifunctional Smart and Solid Flip StopGOINGMAKE compact miter gauge for table includes a smart and solid flip stop for easy and precision setup for woodworking cutting.We supports square face and angle faces workpieces with locating pin. 1. Easy to read and setup scales with magnifying glass and precision pointer. 2. Solid flip stop and locking in security for stable and precision setup and repeat cuts. 3. Easy to zero calibration, just move the flip stop point to the 0 scale and locking, last move the fence and make flip stop to touch the table saw blade and we have pre-designed 1-3mm gaps between blade and fence.. Fits for Most Table Saw and Easy to SetupGOINGMAKE miter gauge fits most table saw on the market with 360mm long miter bars. Including adjuster both at the front, at the end and at the middle of the miter bars. Ensure stable,smooth and fit sliding on the table saw slot. Easy to adjust the ring to make perfect fitness between table saw and miter gauge sliding bar. Our table saw angle guide fits for 38 x 34 inch T slot and U slot table saw band saw router table.. Provides Durability and Precision Cuts for Long Time UseGOINGMAKE miter gauge table saw jig angle gauge is made of aluminum alloy miter gauge and aluminum alloy fence provides a long term use and promise accurate cuts all the time..

FRICTION RESISTANCE - UHMW strips are ideal to use as table saw sled runners due to their superior friction resistance, making it perfect for repetitive sliding tasks.. NO RESIDUE - UHMW plastic is slicker than wood and other plastics, leaving no residue, simplifying clean-up after use. Use our table saw miter slot runners to build crosscut sleds and other jigs.. PRECISION FIT MITER GUIDE BAR - Crafted to standard dimensions, our table saw guide bar measures 34 x 38, fitting snugly into most standard miter slots for secure and accurate jig construction. Predrilled for ease of use. DURABILITY - UHMW plastic, known for its durability, is 10 times heavier than regular polyethylene. Its ideal for table saw track sliders due to its strength.. USA QUALITY - UHMW plastic works great for a table saw miter slide. Use our quality UHMW strips to create sleds and jigs. Proudly Made in the USA.

Precision Crosscut Miters Achieve clean, accurate 90 to 45 cuts with this table saw crosscut sled ideal for repeatable crosscuts, miters, and woodworking jigs that demand accuracy, stability, and smooth control. Smooth Phenolic Base 12 thick phenolic sled base glides effortlessly in standard miter slots without swelling or warping more durable than plywood, making it a reliable table saw sled for long-term shop use. Telescoping Flip Stop Extruded aluminum fence extends from 25 to 38-14 to support long stock includes Micro-Adjust Fence Flip Stop for precise length control when cutting cabinet parts and furniture components. Safe Clean Cuts Adjustable miter bar eliminates side-to-side play, while the Bit-Saver Hold-Down Clamp secures workpieces safely replaceable zero-clearance insert supports fibers for reduced tearout. Whats Included Crosscut sled base fence adjustable miter bar micro-adjust flip stop Bit-Saver hold-down clamp extension work support jig handle replacement zero-clearance insert hardware pack.

The setup blocks can easily set the height of the fence, blades bits and other cutters according to the needs, which is faster and more accurate than using a combined ruler.. Combine bars to setup 100's of measurements. Stack setup bars for a wide variation or sizes, or use on their own, work and measure quickly.. Set up gauge blocks are all 3 inches long. Accurate saw gauge block set sizes 116, 332, 18 ,532 ,316 ,732 ,14 ,516 ,38 ,716, 1532, 12, 2332, 34, 1x2x3. Easy-to-read laser etched labels on each block. Fitted case included, so the combination square will be more tightly protected during transportation.. 15 pcs Blocks Solid Aluminum Construction Black Anodized to better protect router bits and saws..

When building cope and stick door and drawer fronts, one of the tasks that must be done is to cut the end grains of your rails. This sounds easy enough, however the narrower your rails are, the more difficult it is to hold the stock firmly up against a router table fence. Our Rail Guide Coping Sled Pro solves this issue and helps you make precise, square, clean cuts for rail and style doors, drawer fronts and most any other type of end grain cut on your router table.. The idea behind the Rail Guide Coping Sled Pro is simple hold your rails firmly at a 90 degree angle to your router table fence so you can feed your stock through the cutter for the cleanest, squarest cuts possible. When doing drawer fronts which often times use very narrow rails, this sled will prevent your stock from dipping or pushing in too far and also keeps your hands away from harm.. We have included a single sacrificial block with the sled to get you started with your first profile. The sacrificial block helps to prevent end grain blowout at the back of your end grain cuts. Also included is an abrasive strip that is adhered to the adjustable fence. The abrasive strip keeps your stock from sliding or wandering during the coping process. That, along with the heavy duty hold down toggle keeps your stock firmly in place.. Many sleds rely on the miter slot for reference. Our coping sled uses the fence as a reference instead. The Rail Guide Coping Sled Pro features a clear acrylic fence for reference which is offset and raised 2 above the base so you wont cut into the sled. Using a fence rather than a miter bar mounted to the bottom means that you will always be parallel to the router table fence. This is a distinct time saving advantage as you will no longer have keep re-adjusting your router table fence. This robust, full featured coping sled has a laminated thick MDF base that slides across your router table surface effortlessly. The sled also features a large, heavy duty hold down toggle with a 1-58 hold down foot to keep your stock in place. The unit also includes two large and sturdy handles for guiding the sled through the cutter. The maximum stock size is 5 wide by 1 thick. Full instructions are included..

Table Saw Sled Kit You will receive 2 UHMW miter bars for table saw 17 in, 2 universal T-tracks 12 in, 1 star knob and bolt, 1 round washer, and 15 screws, fitting most standard table saw slots Note wooden sled not include.. Well made T-tracks are made of solid extruded aluminum and the table saw runners are made of UHMW linear polyethylene, durability, and smooth, surface burrs-free.. Safe and Efficient The crosscut sled for table saw aids in precise cutting, meeting various cutting needs, prevents measurement and cutting errors, and enhances safety and efficiency.. Low Friction UHMW miter bars for table saw are ideal for use as crosscut sled guide rails, and have low friction and stability without expansion or contraction due to environmental changes.. Function Table saw sled kit is perfect for crosscutting, repeat length cutting, and small cuts, stabilizing workpieces, included knobs and bolts can be used as simple stop blocks for consistent cuts without frequent adjustments to measure fence distance..

Table Saw Sled Kit Package includes 2 UHMW miter bars for table saw sled 17 in, 2 Aluminum T-tracks 12 in, 1 star knob and bolt, 1 round washer, and 15 screws. Compatible with most standard table saw slots Note wooden sled not include.. Well-made T-tracks are made of solid aluminum and the table saw sled runners are made of UHMW linear polyethylene, durability, and smooth, surface burrs-free.. UHMW Miter Bars Ideal for use as crosscut sled guide rails, table saw sled runners and have low friction and stability without expansion or contraction due to environmental changes.. Safe and Efficient The crosscut sled for table saw aids in precise cutting, meeting various cutting needs, reducing measurement and cutting errors, and enhances safety and efficiency.. Multifunctional Cutting Crosscut sled kit is perfect for crosscutting, repeat length cutting, and small cuts, stabilizing workpieces, included knobs and bolts can be used as stop blocks for consistent cuts without frequent adjustments to measure..

SIZES COMPATIBILITY This miter bar features 300mm11.81 inch length, 19mm0.748'' width and 9.5mm0.374'' thickness. Suitable for M6 screws and tapping screw have non-universal mounting holes. ALUMINUM TABLE SAW SLED SOLUTION Crafted from high-strength aluminum alloy, this table saw sled component delivers long-lasting performance. The construction ensures repeated use in demanding woodworking environments. MULTIFUNCTIONAL TABLE SAW The miter for table saw enables accurate angle adjustments when constructing miter sleds. CUSTOMIZABLE MITER BAR SYSTEM Features adjustable stainless steel runners for smooth operation. These miter bars for table saw require user modification drillingtapping when adapting push handles for personalized workshop setups. COMPLETE TABLE SAW UPGRADE KIT Package includes 1 miter bar specifically designed for table saw modification projects. Ideal for constructing miter sleds.

Enhanced 3D control This table saw push block allows you to push down, against the fence, and forward simultaneously for precise, safe cuts. Superior safety The offset handle on this table saw push stick keeps your hand safely away from the blade or router bit. Perfect for thin cuts With its slim 38 design, this push stick for table saw easily fits between the blade and fence for narrow rip cuts. Non-slip grip Neoprene rubber bottom ensures a firm hold without damaging your wood, making it one of the best push sticks for table saw use. Confident ripping The 14 heel secures your workpiece, providing stable feed on table saws or router tables with this push block. Durable build Made from glass fiber-reinforced DuPont nylon, this table saw push block offers stiffness and shatter resistance. Ideal woodworking gift A thoughtful, practical gift for any woodworker, this table saw push stick is sure to impress. American innovation Designed in the USA by the family-owned Hedgehog brand and protected by a U.S. patent.

WHAT'S IN THE BOX - Includes the in-DEXABLE Miter Sled, integrated Drop Zone cut-off catch table, sacrificial end block, miter bar with nylon leaf springs, micro-adjustable flip stop.. PRECISION ANGLED CUTS - The in-DEXABLE miter head features indexed stops for 3, 4, 5, 6, 8 and 12-sided objects, allowing fast and repeatable setups for polygon projects, segmented work, and precise angled table saw sled cuts.. INTEGRATED OFFCUT CONTROL - The included Drop Zone catch table measures approximately 8 x 15 and provides a dedicated platform that catches cut-offs during use, helping keep the work area organized and supporting small pieces during cutting.. REDUCED TEAR-OUT - The included zero-clearance block helps push the offcut past the blade while supporting the material fibers at the cut line to reduce tear-out on the backside of the cut.. AMERICAN MADE PRECISION - Like all Woodpeckers tools, the in-DEXABLE Miter Sled with Drop Zone is precisely machined and carefully inspected in Strongsville, Ohio for consistent quality and reliable woodworking performance..

FOLD AND GO More than just a workbench for garage use, the Pegasus goes anywhere you need extra support . Its easy to pop open for set up, it folds down compact to save on storage space, and fits under your arm for comfortable carrying. TWO-IN-1 DESIGN Seamlessly transition between a workbench and a sawhorse to tackle projects of all sizes. HEAVY-DUTY SUPPORT As a portable workbench, it offers a high load-bearing capacity up to 300 lbs. As a sawhorse, it supports an impressive 1000 lbs. From bulky lumber to potted plants and bikes to heavy equipment, Pegasus can handle the pressure. EASILY EXPANDABLE If you need more room, simply add another Worx support tablesuch as the Pegasus, the Sidekick, or Clamping Sawhorse. Theyre all the same height and use the same connectors for seamless attachment. LARGE SURFACE AREA With a surface size of 31 25 and a working height of 32, this folding work table provides enough space to suit a variety of applications, from staining and woodworking to painting and repairs. BUILT TO LAST, YET LIGHTWEIGHT Made from dependable, molded ABS plastic with steel supports and fittings, this folding workbench will be with you for the long haul. While tough, it only weighs 30 lbs. for stress-free transport. INTEGRATED CLAMPING SYSTEM Strong and reliable, this worktable includes 2 24 quick clamps that keep a firm grip on any project with up to 301 lbs. of clamping force . 4 Clamp dogs are also included hold circular or oddly shaped pieces in place. MEASURING GUIDE No more searching for missing rulers or measuring tape. This portable work table has you covered with a built-in measuring guide. INCLUDES 1 Pegasus Worktable and Sawhorse, 2 24 Quick Clamps, 4 Clamp Dogs, 2 Table Links.

INCLUDES Crosscut Table Saw Sled kit comes with table base, MDF fence face, fence, flip stop, hold down clamp, miter bar and installation hardware to give you everything you need to begin producing precise cuts right out of the box. FEATURES Easy to read 12 graduations, a hairline indicator for mistake free tablesaw setups, right edge zero clearance, and simplistic design for a quick and easy installation. HIGH PRECISION CUTS Complete with an integrated angled ruler to ensure you get the desired cut with accurate measurements. ULTIMATE WOODWORKING JIG Produces quicker, safer cuts for edge and detailing work projects requiring degree accuracy - Supports the material and holds it still for a perfect right angle cut.. PREMIUM DESIGN Provides a large smooth sliding worksurface with an easy to read, accurate scale that produces high precision miters and repeatable crosscuts for table saw applications. WARNING The table saw crosscut sled is intended for use only on cabinet and full-size contractor-grade table saws with a standard 38D x 34 W miter slot. It is NOT intended for use on portable saws and benchtop saws..

INCLUDES 24 universal t track, 19 HDPE miter bars, 3 flip stop, blade guard, flat head wood screws, hex head bolts and nuts. FUNCTION Provides you with an easy DIY kit that includes a t-track for mounting flip stops and fixtures, a premium 3 flip stop, blade guard and hardware needed to cut boards to precise lengths while preventing measuring and cutting errors. 100 SAFE Makes crosscutting safer, more efficient and convenient, while avoiding risking your limb when crosscutting smaller pieces with a crosscut sled specifically calibrated with your table saw. PREMIUM QUALITY The t-track included in this kit is made of solid extruded aluminum and the miter bars are crafted with high durability, high stability HDPE high density polyethylene. DIMENSIONS Universal T-Track 24 long High Density Polyethylene bars 19 long x 34 x 38 3 Flip stop Flat Head Wood Screws 6 x 12 14-20 x 12 hex bolts 14-20 acorn hex nuts.

Table Saw Miter Sled This is the perfect table saw sled, no adjustments needed Simply cut one piece on the leading face, one on the trailing face, and voila Since both pieces reference off a perfect 90-degree angle, the miters will fit perfectly.. 45 Degree Miter Sled This table saw sled system gives you an exact 45-degree cut every time. Our table saw miter is great for picture frames or anytime accurate corner. Miters cuts are needed.. Adjusting Miter Track Fit Use a 764 hex wrench not included to advance the nylon set screws in the Rockler 45 degree miter sled bar until you achieve a smooth, no-slop fit in your saws miter track.. Standard Slot Through slots in the base allow you to securely clamp moldings at table level. This table saw miter sled fits standard 38 x 34 miter slots.. Easy To Use The table saw accessories miter can be easily drilled to add extended fences and stops. Pre-installed adjustable nylon pins provide a no-slop fit to the miter track..

Perfect Size Versatility The Benchtop Board Flattening wood slab jig is perfectly sized to fit on a workbench or shop stand, ideal for routing flat faces on smaller slabs, end-grain cutting boards, or resin charcuterie boardsno need for a big drum sander. Effortless Machining The router sled for flattening slabs jig features precision guide rails, low-friction carriage, and a trolley that lets you smoothly guide your router over the surface for a flat finish shearing action minimizes tear-out, reducing the need for sanding. Sturdy Precise The router flattening sled kit includes rigid extruded aluminum base rails that attach securely to your work surface with included hardware slots in the rails allow for fine-tuning, and the flattening router jigs for woodworking keep them perfectly parallel, allowing for accurate routing. Safe Compatible Our benchtop board flattening router sled kit includes a reinforced plastic router carriage with low-friction pads, safety catches, and a pre-drilled clear acrylic router baseplate compatible with most popular mid-sized routers. What's Included This benchtop board slab flattening jigs woodworking comes with 2 aluminum cross rails, 2 aluminum base rails, 2 cross rail end caps, 2 base rail end caps, 2 glide bases, 1 router baseplate, 1 router carriage, and 1 complete set assembly hardware router, bit, and workpiece not included.

Most Versatile Add-On Fence XT XTENDER 46 Fence stands 5 tall, includes three T-slots along the top for feed control accessories, milled clamp attach slots for multi-position set up, special slot to add BOW Feed Supports accessory, and a slot for attaching to Delta UniFence and Harvey fences. Robust Aluminum extrusion with anodized finish and 3 sizes for all your needs. Use with XT Feed Supports to extend smaller tabletops and improve stability, cut quality, feed control and safety. Extend Fence and Table Surface XT XTENDER Fence works in tandem with optional XT Feed Support Accessory. Bow Feed Supports attach to the Fence and function as a shelf extending the table surface for infeed andor outfeed. Transform the smaller tabletops by extending feed support and control over a wider area. The 46 XTENDER Fence extends small Portable jobsite saws, benchtop saws or bandsaws. Improves safety as wood is easier to control and kept square to the blade. Fast Set Up XTENDER Fence attaches and detaches from your existing fence in seconds with T-Track Clamps Required Sold Separately. Part XT2. Bow XT T-Track clamps are designed to fit most portable saws, bench top saws, bandsaw, and full cabinet saw fences. Fast Set up ensures convenience to use XTENDER when you need it. Includes special Slot for Delta UniFence and Harvey Fences for quick attach. Multi-Position Fence Placement Milled Clamp Slots are located on the back of the XTENDER Fence and offer multiple positioning options in relation to your Saws fence. Works when using a fence longer than your table surface and paired with Bow Feed Support accessory Part XT1. Position XT XTENDER Fence forward for greater infeed control position back for outfeed control or center placement for infeed and outfeed control. Slots accept Bow XT T-Track Clamps. Add Bow Safety Accessories Take full advantage of the Bow XTENDER Fence System. Three T-Slots on the face, Top and Back of the fence enable adding woodworking accessories like Bow FencePRO Featherboards, stops, etc. T-slots run the length of the fence and accept 516 or 14 T-bolts. Check out the kit options and make your saw safer with better control, better cuts and added stability when cutting longer boards. Durable Construction and Finish Constructed from robust aluminum extrusion with an anodized finish that provides long-lasting durability and resistance to wear, ensuring reliable performance for all your woodworking projects. Space-Saving Storage Design Features a built-in through hole that allows the fence to hang conveniently on a wall, saving valuable workshop space and keeping your tools and equipment organized and easily accessible.

Durable Construction Crafted from high-quality UHMW plastic, this crosscut sled is built to last, providing stability and reliability during every cut on your table saw.. Smooth Sliding Surface The sleek design of the sled ensures low friction sliding, allowing for seamless operation and precise crosscuts with ease.. Easy Setup Featuring predrilled holes and matching screws, this sled is a breeze to set up, saving you time and effort so you can focus on your woodworking projects.. Customizable Length With the ability to customize the length of the sled, you can tailor it to fit your specific cutting needs, enhancing efficiency and versatility in your workshop.. Enhanced Precision Ideal for various cutting tasks, this crosscut sled for table saw delivers unmatched accuracy and control, helping you achieve professional results every time. Experience the difference with the FixlyFido Crosscut Sled For Table Saw..

Heavy-Duty tube steel construction provides the strength you need for safe operation. Upport bar hardware holes for secure fastening of saw to the stand. Lightweight folds flat for easy handling, storage, and transport. Designed for use with the DW7480 compact job site table saw, Dcs7485 60V table saw and DW745 compact table saw.

If you own a table saw, you probably have come across a situation or two where you need to make smaller cuts or make cross cuts. You may also have had the need to make repetitive cuts of the same length. Making small cuts, cross cuts and repetitive length cuts is where table saw crosscut sleds excel. Crosscut sleds help stabilize the work piece and are very accurate since they are essentially calibrated to your saw during the sled building process.. Some time ago we noticed a lot of companies had UHMW bars available for purchase. While we as a woodworking company know exactly what they are used for, many novice or non-woodworkers do not. Thats when we decided to create this package with pre-cut UHMW bars, pre-cut aluminum track, a knob and bolt and an easy to understand how to guide booklet so you can create your very own, custom crosscut sled to fit your table saw. UHMW bars are most commonly used as runners for crosscut sleds since they dont produce as much friction as wood does. Another advantage is that UHMW wont expand or contract like wood does during drastic weather changes. Each bar is approximately 34 x 38 which fits most standard table saw slots. UHMW bars are also slick and wont leave any residue, dust or shavings behind like wooden bars tend to do.. The tracks that are included in this kit are made from solid extruded aluminum and are Made in the USA. Each track is cut to length for the perfect sub-fence on the crosscut sled. The included knob and bolt is for making a simple stop block which when finished, can slide the length of either track along the sub-fence. The stop block will allow you to make repetitive cuts without having to constantly move and measure the fence distance each time you make a cut.. We have also included a full color and detailed how to guide book to help you with the crosscut sled building process. Each kit comes with 2 each 19 long by 34 by 38 UHMW bars, 2 each 12 long mini tracks, 1 each knob, 1 each 14 by 20 tpi bolt, 1 ea. blade guard, 1 ea. stop block and a how to build your own crosscut sled guide book. Make your crosscut sled to the size you want or need for your table saw and your specific cutting needs. Please Note, the bars do NOT FIT RYOBI table saw track slots. MADE IN USA.

Featuring 4 NoPlay Expandable Glides for a perfect fit into your x 38 miter slot. This miter gauge also features an adjustable protractor style head with a super slick UHMW protective base pad, along with a bright red, easy to see cursor and steel miter bar. The Dual 45 End Aluminum Fence is ideal for zero clearance supported cuts. The patent pending Expandable Glides are the simplest way to achieve an ideal miter bar fit into your miter slot. Once in the miter slot, adjust your NoPlay Expandable Glides by rotating the machine screw until the glide applies just the right amount of pressure to the side wall of your slot. Adjust the remaining glides for a perfect fit. The protractor style head features a super Slick Base Pad on the bottom to give you the perfect slick surface to slide smoothly along your table top. Not only does the pad slide smoothly, it also protects your table top from getting scratched or marred. The protractor head also features 13 positive stops for quick common angle adjustments.. A bright red handle and a bright red cursor make for easy angle adjustments that you can easily see. Loosen the handle, rotate the protractor style head and once your position is set, tighten the handle to lock the angle in place. If your angle is one of the positive stops, you must still use the handle to loosen and lock the head into place.. The Premium Aluminum Dual 45 End Fence is the perfect fence for accurate angled cuts. The Dual 45 Ends allow you to get tight to the Sawblade when cutting 45s. This helps support your stock and prevents the potential for dangerous kickbacks. The fence is completely adjustable and can be removed if needed..

Dock Lock the included INCRA Miter Gauge in Seconds. Removable t-slot retaining clips adjustable miter bar. GlideLOCK Miter Bar - The Miter 1000SE's 6 expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard miter gauge channels. Special Edition Telescoping INCRA-LOCK Fence. Special Edition 110th Vernier Cursor. Table size For adequate support, the Miter Express requires a minimum of 11 from the side of the blade to either the left or right edges of the saw sled can be installed on either side of the blade..

If you own a miter gauge - any miter gauge. This sled is a sliding, miter-cutting platform that fully supports and controls your work piece throughout the cut. Miter gauges drag your board across the table, a sled slides the work piece giving more support and control creating better, more consistent cuts.

TABLE SAW JIG ROUTER TABLE JIG - 5-12 of base plate travel plus 3-12 from the adjustable base gives you 9 of overall extension.. MICRO-ADJUSTABLE - Bearing-guided lead screw allows precise fine-tuning for perfect-fitting joints.. ANGLE-ADJUSTABLE - Lock in at any angle between 44 and 91 for complex miters and compound cuts.. FLEXIBLE FENCE CLAMP SETUP - Three track grooves for repositioning the fence and securing stock with included or optional clamps.. AMERICAN MADE QUALITY - Precision machined and assembled in Strongsville, Ohio..

Premium Home Improvement Tools Portable table saw top helps you make rip, angled, and crosscuts in materials. Versatile Woodworking Tools The integrated track saw guide and measuring scales help you make repeatable cuts. Workshop Accessories Adjustable track hinges and mounting plates for use with Kreg Track Saw Guide Track. Heavy-Duty Carpentry Tools Includes angle guide and repetitive stops to get correct alignment to the saw guide for perfect 90 and angled miter cuts. Premium Kreg Tools We offer products that help woodworkers close the gap between idea and outcome.

Precision Miter Gauge System Complete miter gauge solution with adjustable fence designed for accurate, repeatable angle cuts on table saws. High-Accuracy Angle Control Engineered for precise miter cuts to improve consistency across woodworking and shop projects. Smooth, Controlled Operation Designed to glide easily in miter slots for stable, repeatable cutting performance. Heavy-Duty Construction Built with durable materials to withstand frequent use in professional and DIY workshops. Premium Kreg Tools We offer products that help woodworkers close the gap between idea and outcome.

Elimantes dangerous gap around blade where thin off-cuts can get wedged. Fits Sears Craftsman 10 belt-drive models 1977 to mid 2004 check size, see DL-1U, RIDGID TS2412, TS2424, TS2400. Measures 14 x 3-34 x 316 PLEASE MEASURE before ORDERING. Offers superior rigidity, flatness, durability, and low friction reduces chip-out and splintering. PLEASE NOTE CR-1 does not fit models TS2400LS, TS2400-1 or the new TS2410 See RG-2.

STRONG GRIP AND CONTROL Made in the USA, the Smart Push Block uses a Green GRIP podular surface for strong gripping power, making it a dependable table saw push block and essential woodworking tool for accurate cutting. SMART HOOK TECHNOLOGY Auto-retracting smart heel hooks engage at the end of your workpiece to prevent slips, giving this gripper push block an advantage over standard push blocks for woodworking with added safety. MULTIPURPOSE WOODWORKING TOOL Ideal for use on table saws, router tables, jointers, and band saws, this high-visibility push block has an ergonomic handle design and works with table saw accessories and router table accessories for precise control. 90-DEGREE FLIP GUIDE CONTROL The MICROJIG GRR-RIP BLOCK has a 90 degree Flip Guide which supports vertical operation for cutting veneers, resawing on the band saw, or shaping beaded face frames on the router table, with Smart Hooks always ready to engage. IDEAL FOR LARGE PROJECTS Use the DeflectorConnector available separately to protect against debris and woodchips or bridge two push blocks together for added stability when handling raised panel doors, veneers, or resawing.

STRONG GRIP AND CONTROL Designed in the USA, the MICROJIG GRR-RIPPER 2GO Push Block has a Green GRIP non-slip surface for strong gripping power, making it a dependable table saw push block and essential woodworking tool for accurate cutting. KICKBACK PREVENTION Designed with a precision leg and tunnel system, this gripper push block feeds and controls both sides of the cut, virtually eliminating kickback while providing superior control. MULTIPURPOSE WOODWORKING TOOL Ideal for use on table saws, router tables, jointers, and band saws, this high-visibility push block has an ergonomic handle design and works with table saw accessories and router table accessories for precise control. PRECISION THIN CUTS With a minimum cutting width of just 516 8mm, the MICROJIG GRR-RIPPER BLOCK excels at making accurate, thin cuts that would be unsafe with bare-hand feeding. READY TO USE The MICROJIG GRR-RIPPER 2GO comes fully assembled with a Color Code Index sticker for the rip fence scale, clearance step, and dovetail grooves for attaching custom accessories For longer cuts, simply use two 2GO Push Blocks together.

Protect hands and prevent kickback like never before. Powerful high-friction durable grip for extreme hold. Precision cutting and control down to 14 Ripping. Fully adjustable for easy handling. Work with small stock safely on the table saw, Router table, Jointer, Band saw. Designed in USA. A true MICROJIG Innovation.. 3-Directional Force for total control of the workpiece.

ZERO-PLAY ADJUSTMENT WITHOUT REMOVING YOUR SLED Fine-tune your fit anytime directly from above using the included 2.5 mm Allen keyno need to remove the miter bar or disassemble your crosscut sled. The adjustable expansion collars help reduce side-to-side play for smoother tracking and more accurate cuts on your table saw sled, crosscut sled, router table jig, or box joint jig. SMOOTH GLIDE ROUNDOVER DESIGN Sharp-edge runners that catch during setup, the roundover front design allows easier entry into the miter slot for smoother operation. Ideal for woodworking jigs, crosscut sleds for table saws, spline jigs, coping sleds, taper jigs, and custom table saw accessories where repeatable accuracy matters. DURABLE ANODIZED ALUMINUM RESISTS WARPING AND SWELLING Made from premium anodized aluminum alloy for long-lasting stability in humid or changing shop environments. Unlike wood runners or plastic alternatives, these miter bars resist warping, swelling, oxidation, and wear to help maintain precision over time. FITS STANDARD 34 x 38 MITER SLOTS Designed to fit standard 34 inch x 38 inch miter slots commonly found on table saws, router tables, and woodworking machines. Compatible with both T-slots and U-slots for broader shop compatibility. NOT compatible with 58 inch miter slots. MITER BAR SET WITH HARDWARE AND TEMPLATES Includes 2 17 inch aluminum miter bars, 12 8 wood screws34 long, 8 14-20 UNC countersunk machine screws, 1 2.5 mm Allen key wrench, printed instruction manual, and mounting templates.

ACCURACY PRECISION - The Dubby Jr. Crosscut Sled enhances your table saw precision, enabling accurate miter joints and 90-degree cuts. Easy setup and easy-to-read scale with clearly marked shapes.. SMALLER IN STATURE - The Dubby Jr. is a compact crosscut sled for table saws, perfect for precision woodworking minus the cost of larger machinery. Get accurate cuts with our handy table saw sled kit. SMOOTH SLIDING PARTS - Adjustable MDF face and a stop block for precise, repeatable cuts. These smooth sliding components on the cross cut sled kit work together to produce accurate cuts every time.. EASY ANGLE SCALE - The angle scale is the most accurate, easy to read scale available. More accurate than a miter gauge. No calculations or test cuts needed. Perfect for any shape from 4 to 16 sides.. CROSSCUT SMALLER PANELS - The Dubby Jr. has the capacity to crosscut smaller panels safely without material walking. Cut perfectly square panels for your furniture and cabinet making projects.. Does not fit Ryobi table saws..

INCLUDES 2 Featherboards with Threaded 5 Star Knobs, T-Bolts, and Miter Slot Brackets. FUNCTION Provides optimal feed control and holding action for your stock with minimal kickback to provide you with high precision cuts. FEATURES This kit possesses additional hardware for adaptive mounting solutions, including miter slot brackets for horizontal mounting, vertical mounting for 3 multi-tracks and plastic spacers for stackable featherboards. VERSATILE This feather board contains a miter lock system plus a reversible profile that is compatible with both, t-slots and miter slots for table saws, band saws and router tables. PREMIUM DESIGN Manufactured in color-alert orange, these featherboards are quick and easy to adjust and are molded out of high quality plastic designed to give you functional flexibility and long term usage.

THIN RIP TABLE SAW JIG Great for precision cuts. Simply slide the guide into the table saw's U-track slot and lock it in front of the saw blade. The table saw clamp can extend up to 8 inches from the slot to the blade. Works with 38 x 34 U-slots and 14 x 38 T-slots.. 3 PULLEY DESIGN The table saw jig can provide safe and fast thin ripping. 3 pulley design, with a larger contact area with the workpiece, more stable when in use. One of them is a one-way pulley, which can ensure that the workpiece moves forward and will not rebound, which is safer.. PRECISION CUTTING The table saw guide is precise and adjustable. Includes both imperial and metric laser engraved scales. Start by bringing the pulley close to the saw blade, determine the position of the scale indicator, and set the size of your workpiece. Repeat so each workpiece is the same size as the first for precision cutting.. HIGH QUALITY The thin rip jig is made of high-quality aluminum alloy, the structure is carefully designed, and the measurement accuracy is 132 inch. This tool ensures that each cut reaches the required size and accuracy, reduces material waste and improves the work efficiency and quality of woodworking.. AFTER-SALES SERVICE If the product has any quality problems during use, or you have any questions during use, please feel free to contact us, we will give you a satisfactory reply within 24 hours..

Crosscut Sled For Table Saw This miniature cross cut sled lets you use your table saw to cut small parts to length. Our crosscut sled includes a miter track stop that limits the forward travel of the sled.. Table Saw Crosscut Sled is Great for Our table saw fence system is great for cutting dowels, tenon stock, and small moldings at a precise 90 angle, with little to no tear-out.. Zero-Clearance Support This sled system features zero-clearance support, which reduces the chance of small pieces getting stuck between the blade and throat plate, or falling through entirely.. Extremely Durable Our aluminum table saw sled runners are ideal for constant repetitive use. This zero clearance table saw insert does not absorb moisture and will not swell up over time due to exposure.. This Crosscut Sled for Wood Fits Most Table Saws A small plastic ramp on one side of the kerf carries the drop-off piece away from the blade. The rear-mounted blade guard is adjustable to fit most table saws for woodworking..

Box Joint Jig Make a strong, tight-fitting box joint router bit that is great for small to medium-sized boxes This woodworking tool makes the perfect accessory for your router table.. Interchangeable Indexing Keys Our router jig uses precision-machined solid brass indexing keys to ensure uniform finger spacing. The keys are included for three finger widths , . With improvements in design, these router accessories can be swapped and can be stored in slots on the sled.. Smooth Sliding Sled The smooth-sliding router table sled features long ''skis'' that keep it square to the router bit and tabs on the bottom that stop the sled at the end of the cut. Lock it into the miter slot of your router table with our comfortable Easy-to-Grip knobs and you're ready to route.. MDF Platform Place the MDF fence on your box joint jig to control tear out and apply router bit lubricant on the melamine-coated low-friction MDF platform for easy sliding and enhancing durability. The ergonomic knobs lock the platform into a miter slot.. Whats Included Our router finger joint jig includes the following essential woodwork tools - 1 Melamine-coated MDF platform, 2 Soft-grip knobs with miter track hardware, 1 Glass-filled nylon sled, 1 sacrificial fence face, a brass indexing key, a brass indexing key, a brass indexing key, and an instruction manual, all aimed to help you perfect your box joint routing..

An Idea Gift for Woodworker, Carpenter and Craft Man. Optimal Blade Size Through numerous manual tests, We found that the 6 Japanese saw blade is the ideal size for precise cutting, enabling easy flush and finish cuts.. Durable and Flexible Saw Blade The hand saw blade is made of SK5 high-carbon steel. The Japanese pull saw teeth are processed by a high-frequency hardening machine imported from Japan, and the hardness can reach HRC60-63 degrees.. Double Edged One side of Japanese hand saw is 17 TPI for cutting hardwood, and the other side is 14 TPI for cutting softwood. Also can seen as Rip cut and Cross cut.. Hardened 3-Edge Teeth The hand saw has three-sided grinding gear design, sharp edge, faster chip removal, and smoother cutting.. Efficient after-sales service if you have any problems, you can ask us for help at any time, we will reply you within 24 hours to ensure your satisfaction and peace of mind..

RACK AND PINION FENCE RAILS - Ensures fence stays parallel to blade for fast smooth, and accurate cuts. INTEGRATED FOLDING STAND - Legs quickly fold in to provide portability and convenient storage. PARALLEL BLADE ALIGNMENT - Available micro-adjustment of blade so that it is parallel to rip fence and miter slot. 4x4 CUTTING CAPACITY - Cuts material up to 4x4 at 90 degrees. 2-47 BEVEL CAPACITY - Cuts between 2 positive stops at 0 and 45 degrees with quick release lever. DUST PORT ELBOW - Redirects dust to a container for easy cleanup.

Precise Crosscuts MiterOur table saw cut off sled is equipped with a 12 scale and a fine line indicator for easy reading while also ensuring the accuracy of the bevel angle. The adjustable 90 stop block ensures that the cross-cut frame and the saw blade are precisely at a 90 angle, enabling perfect and precise vertical cross-cutting. Note The 90 stop block needs to be calibrated before use.. Compatibility limitations Our table saw cut off sled is specifically designed for cabinet full-size contractor-grade table saws, and is compatible with their standard bevel-cut groove specifications 38 D x 34 W miter slot. Please note that this sled is not suitable for small table saws or portable table saws as its structural dimensions and groove specifications may not be compatible. Multiple Security Guarantees When using the cross-cut sled, your hands can always be placed on the main body of the sled or the front push handle, without having to approach the saw blade. Its wide base and sliding slot structure ensure stable operation. Combined with the stop blocks and clamping device, it can firmly fix the wood, effectively preventing rebound. This fully ensures your safety from both the operation isolation and material control aspects. Table Saw Sled Kit Incledings MDF base 23 1316, MDF fence face, miter bar 38 D x 34 W, extruded aluminum fence, hold-down clamp, flip stop, installation hardware, wear strips, Allen key, screwdriver instructions. Outstanding After-Sales Service All of our products have passed our strict inspection before any shipments. If there is any problem with your table saw crosscut sled, please communicate with us and we will assist you to solve the problem within 12 hours. If table saw crosscut sled has any quality problems, we will make up for your loss or replace it with a new one.

Fits Most Table Saws Our portable table saw stand is compatible with a wide range of table saw brands and models. With an adjustable installation range of 17.44 in x 8.87 in to 22.64 in x 19.1 in, you won't have to worry about compatibility issues. Simply measure your table saw's dimensions beforehand to ensure the ideal fit.. Built for Easy Transport Equipped with two 8-inch anti-slip rubber wheels, this table saw folding stand allows you to easily move your table saw to different job sites. The wheels reduce the strain of transporting heavy equipment, so you can focus more on your cutting tasks.. Rock-Solid Stability Constructed with high-strength steel and a robust frame, this table saw stand with wheels supports up to 350 lbs. Even during complex or heavy-duty woodworking tasks, it delivers the solid stability you need for precise, secure cuts.. Easy Storage Portability Featuring a handy release lever, this rolling table saw stand allows you to easily fold or unfold the stand with a simple press. The quick-fold design saves valuable storage space while making the stand highly portable for effortless transport.. Set Up in Minutes The package includes a clear, easy-to-follow installation guide to help you quickly secure your table saw to the stand. Once all parts are properly tightened, youll be ready to jump straight into your cutting projects without any delays..

Fit for Most Table Saws Our miter gauge is expertly designed to fit the majority of standard table saw slots measuring 34 x 38 in 19 x 9.5 mm. To ensure a perfect match, please measure the slots on your table saw before purchase. Featuring a detachable disc, our miter gauge is compatible with both 34 x 38 T-shaped and U-shaped slots. Ideal for most table saw brands, and is upgrade for precision woodworking.. Precision Angle Cutting Experience cutting precision with our adjustable solid aluminum head, engineered with 15 positive stop holes for ultimate accuracy. One stop hole is set at 90 degrees, with seven additional holes on each side at 15, 22.5, 30, 35, 45, 60, and 67.5 to cover most woodworking angles. For more intricate angle cuts, the gauge adjusts proportionally, allowing you to achieve precise angles efficiently and effortlessly.. Partially Assembled Components This miter gauge for table saw is shipped partially assembled to streamline your setup process. When it arrives, you won't need to fuss with numerous small parts. Just attach a few core components, and you're ready to go. It maintains the accuracy of your measurements without the typical assembly hassle.. Easy Operation, Simple Adjustment Our table saw miter gauge features a steel miter bar equipped with an adjustable bead spring plunger on the side. When placing the miter gauge in the table saw slot, if you notice any gaps, simply use the included hex wrench to adjust the plunger. This adjustment ensures an ideal fit within the slot, improving wear resistance and simplifying your operations.. Refined Durability in Every Detail This precision miter gauge is constructed from aluminum alloy, ensuring durability and resistance to deformation. Featuring a convex-concave grating with fine-tuning screws, it allows for manual micro-adjustments to enhance precision. The angle plate scale is meticulously etched using laser engraving technology, and the textured metal handle provides a secure grip that avoids slipping..

PREDRILLED HOLES - Each bar has 5 exact size designed predrilled and countersunk holes for 20 specific sized screws included that ensures no expanding of the material when screws are inserted.. EXCELLENT SLIDING MATERIAL - due to the low coefficient of friction it has, which makes it ideal for sleds where repetitive sliding is necessary.. VERY SLICK AND SELF LUBRICATING Very high abrasion resistance. UHMW bars wont leave any residue, dust or shavings. The non-stick surface is easy to clean.. EXTREMELY DURABLE Ideal for constant repetitive use. UHMW Ultra High Molecular Weight Polymer plastic is 10 times heavier than regular high-density polyethylene for stability. UHMW wont expand or contract like wood does. Does not absorb moisture and will not swell up over time due to exposure.. OUTSTANDING IMPACT STRENGTH - Even at low temperatures. JIGS, FIXTURES OR MITER SLOTS 34 X 38 ideal for table saw, band saw or router table..

Capitalizing on a great idea, the folks at Incra. The sled with T-track and clamping fixture secures the work piece as one solid unit for precision cross-cutting at any angle. The right-hand portion of the sled, once cut. Table saw that blends incremental angle control and a special 3-panel sled. Precision angle indexing teeth are laser cut in solid steel. 364 lock solid angle stops in 12-degree increments. Ten expansion disks adjust both sides of the bar for zero side play. Hold down clamp locks your work piece onto the sled.

Work on both sides of your blade. Replaceable zero clearance plates. Zero play miter bar wioth spring-loaded ball detents. Easy-to-place and use flip stop. Heavy duty toggle clamp hold down.

INCLUDES Table Sled Body and Zero Clearance Fence, Miter Slot Stop and Knobs, Miter Bar, Blade Guard, Screwdriver and Installation Hardware. FUNCTION This little sled is ideal for making high precision, small cuts on difficult woodworking projects with optimal safety for your fingers while cutting stock. FEATURES Adjustable rear-mounted blade guard fits most table saws, a fence and base that allows you to run the saw through the width of material that is removed during the cutting process. 100 SAFETY The sled also comes with a miter safety stop plate to prevent forward travel and is designed to keep your fingers clear of danger, allowing you to cut with confidence. PREMIUM QUALITY Most table saw small parts are made with high quality aluminum for durability with an MDF zero clearance board.

Precise Angle Cutting This table saw accessory is 0.04 inch 1 mm high precision. Metric and imperial scale makes your work more convenient. Additional trim blocks raises working efficiency. Both sides 60 angle adjustable, ideal for crosscutting wood at a specific angle.. Compatible Standeded Slot Our table saw sled is suitable for a standard 0.75 x 0.38-inch miter slot. Laser marking technology is friction-resistance to ensure accuracy. It is an economical solution for your table saw crosscutting needs. The adjustable, solid aluminum head is machined with 11 positive stop holes. 1 hole is at 90 degrees while the 5 holes on both sides are at 10, 22.5, 30, 45, 60 and 90 degrees.. Premium Sturdy Construction This woodworking tool is made of aluminum alloy, ensuring its durability and sturdiness. The steel miter bar is equipped with a removable metal retaining disc to prevent accidental lifting.. Simple Secure Operation An adjusting screw and guide wheel are added in the middle, which is more convenient to insert into the slot hole and fix the seat. The miter gauges are flat without burr, secure, and hands-free.. Wide Application The table saw miter can improve the safety and accuracy of the table saw and the router table. It also can be used for router tables and jointers. Miter gauge fence system is currently a must-have for every family..

Precise Angle Cutting This table saw accessory is 0.04 inch 1 mm high precision. Metric and imperial scale makes your work more convenient. Additional trim blocks raises working efficiency. Both sides 60 angle adjustable, ideal for crosscutting wood at a specific angle.. Compatible Standeded Slot Our table saw sled is suitable for a standard 0.75 x 0.38-inch miter slot. Laser marking technology is friction-resistance to ensure accuracy. It is an economical solution for your table saw crosscutting needs. The adjustable, solid aluminum head is machined with 11 positive stop holes. 1 hole is at 90 degrees while the 5 holes on both sides are at 10, 22.5, 30, 45, 60 and 90 degrees.. Premium Sturdy Construction This woodworking tool is made of aluminum alloy, ensuring its durability and sturdiness. The steel miter bar is equipped with a removable metal retaining disc to prevent accidental lifting.. Simple Secure Operation An adjusting screw and guide wheel are added in the middle, which is more convenient to insert into the slot hole and fix the seat. The mitre gauges are flat without burr, secure, and hands-free.. Wide Application The table saw miter can improve the safety and accuracy of the table saw and the router table. It also can be used for router tables and jointers. Miter gauge fence system is currently a must-have for every family..