Protection WireSpark Plug Wire Heat Shield Widely used as a solution to your burning spark plug wires which create a lot of heat. These universal spark plug wire cover can provide a good heat protection to spark plug wires especially on engines with excessive exhaust headers.. Perfect UseSpark Plug Wire Heat Sleeve Works well with 90 degrees, 45 degrees, and straight spark plug . Fits most hot rods and classics engine. Also fit for most angled straight boots. Length is about 6.1 inch long.. Materials Spark Plug Wire Heat Shield Made with two layers of high temperature titanium material. The thick material is long enough to protect spark plug wires as it nears the header or exhaust manifold helping to increase longevity of wire and maintain maximize spark for as long as you keep your vehicle.It can withstand heat up to 2500 degrees intermittent.. Easy InstallationSpark Plug Wire Heat Sleeve Easy to slip in the boot heat protector on to each boot of the spark plug wire. Just slip the large end with the sewn stitching over the boot. Then carefully slip the ringed end over the boot that connects to the spark plug.. 100 GuaranteeWe will refund you immediately if you don't satisfied with the item you received. You will enjoy 12 months long service. Any problem please feel free to contact us.

CompatibleThis universal spark plug boot protector can fit most angled and straight boots.Fits For most hot rods and classics engine including GM Chevy , GMC, OLDS, Cadillac, Pontiac, Buick, Ford, Chrysler, Dodge, Plymouth,such as 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 engines.. FunctionSpark Plug Wire Boot Sleeves look great, helps reduce misfires,Resists damaging chemicals, extends life of wire boots.non-flammable protects against chemicals resists water, Protect spark plug boots and spark plug wires from Excessive Engine and Exhaust Heat.. FlexibleEach Boot Is 6inch Length,Spark plug wire boots will work with 90 Degree, 45 Degree, And Straight Spark Plug Boots.Length615.5cm ID125mm. Easy InstallationJust Slip On Sewn End Over Spark Plug For Maximum Protection ,Spark Plug Sleeves Can Withstand Heat Up To 2500Degrees Fahrenhett. Spark plug boot heat socks, protect your spark plug wire sets performance and increase their lifetime.. CompatibilitySet of 8 spark plug boot protector, Made From Double Wall Braided Fiberglass Sleeving, keep your spark wire and spark plug cooler in a high temperature environment,Constructed with double layered,they create an effective non-flammable thermal barrier that will extend the life of your ignition wires..

Description Protection DEGEOBERLIN Spark Plug Wire Heat shield helps prevent burn-through, hardening and cracking of boots. Enhance the performance of the engine, extends lifetime of the wire plugs. Spark plug heat protector Header heat wrap both for boot and wire, can protect your expensive plug wire set's performance and increases their life using for LS1 LS2 SBC BBC 350 454.. Durable MaterialThe spark plug wire boots are made of two layers of basalt material. It has good high temperature resistance and anti-corrosion effect, and the thermal insulation temperature can reach 2500 degrees.. Compatibility Length 6.115.5cm, ID 1.435mm, it will work with 90 degrees, 45 degrees, and straight spark plug boot heat socks.. Professional installation No instruction included. Just slip the large end with the sewn stitching over the boot. Then carefully slip the ringed end over the boot that connects to the spark plug. The other end is covered with a metal circle for easy installation.. Package Included8 pieces. Wear gloves and long-sleeved clothing before installation to prevent stone fibers from falling on your body..

High-temperature Resistance The spark plug wire boot is made from materials that can withstand temperatures of up to 2500 degree, protecting your spark plug wires from damage caused by high engine temperatures.NOTICE Our product is vacuum packed. If you receive a product that is not vacuum packed, please return it and complain about receiving counterfeit goods. Thank you. Universal Perfect Fit This spark plug wire boots heated shield is designed to fit most motor vehicle engines and is easy to install, making it a versatile addition to any engine bay.. Improved Engine Performance By reducing the heat that's transferred to your spark plug wires, this spark plug wire protector can help to improve ignition performance and reduce the risk of misfires.. Durable Protection The spark plug heat sleeve provides reliable protection for your spark plug wires, helping to prevent premature wear and damage.. Essential Component Whether you're building a high-performance engine or just want to protect your existing engine from heat damage, this spark plug heat protection is an essential component that can help to extend the life of your engine wires..

Spark plug boots durable protection BLISSSHINE spark plug boot protector helps prevent burn-through, hardening, and cracking of boots. The spark plug heat sleeve cover can protect your plug wire sets, especially on engines with excessive exhaust headers.. High Temperature Resistance Material8pcs spark plug boot protector made in double wall braided fiberglass sleeving triple wall at the sewn end. The spark plug wire heat shield has good high-temperature resistance and anti-corrosion effect, it can withstand heat up to 2500 degrees intermittently. The 6 inch spark plug wire boot is long enough to protect spark plug wires near the header or exhaust manifold.. CompatibilityEach spark plug header boots length is 6.115.5cm, ID 0.661.66cm. It will work with 90 degrees, 45 degrees, and straight spark plug boot heat socks. The spark plug wire heat shield fits most hot rods and classic engines, note Only fit for vehicles that burn petrol Compatible with Ford, Chevy, GMC, Cadillac, Pontiac, Buick, Chrysler, Dodge, etc.. Spark Plug Boots Easy installationSpark plug heat shield sleeve just slip the large end with the sewn stitching over the boot. Then carefully slip the ringed end over the spark plug wire boot that connects to the spark plug.. Package Includes8 Red spark plug wire boot sleeves. You'll get a 12 month warranty. Please note only one Blissshine supplier in Amazon. Purchasing from elsewhere will not offer you a warranty..

3000F Heat Protection for Gas EnginesDual-layer fiberglass construction withstands 13002000F continuous heat and up to 3000F peak. Designed to protect spark plug wire boots from extreme temperatures near headers, manifolds, and turbo components. Suitable for modified vehicles, towing, work trucks, and daily drivers.. Prevents Burnout and Extends Ignition LifeShields ignition wires and coil boots from heat damage, cracking, or melting. Helps maintain stable engine performance by protecting spark plug boots in high-temp conditions.. Compatible with Most Boot Angles and V8 EnginesEach 6 inch sleeve with 1.4 inch inner diameter fits 90, 45, and straight spark plug boots, including thicker aftermarket wire sets and coil-on-plug setups. Works with LS, SBC, BBC, 350 454 gas engines. Not for diesel glow plugs.. Tool Free InstallationFlexible and expandable fiberglass sleeves slide over spark plug boots easilyno tools required. Installs in minutes to deliver long-lasting heat and abrasion resistance.. 8 Pack Full Engine CoverageIncludes 8 spark plug wire boot heat shields for complete V8 coverage. Resistant to oil, fluids, abrasion, and corrosion. Ideal for cars, trucks, SUVs, and performance builds. Wear gloves when handling fiberglass..

Brand new and high quality, Made From Double Wall Braided Fiberglass Sleeving Triple Wall At Sewn End, you will find it is affordable reliable and built to Last, at least you can use for a long time. Package Include 8x Red Boot Heat Sleeve Protector Cover, Each Boot Is 6inch Length, Boots Will Work With 90 Degree, 45 Degree, And Straight Spark Plug Boots Length615.5cm ID125mm. Spark Plug Boot Cover is Made from fiberglass material, protect from Heat from 1000 Fahrenheit 550 Celsius Note only fit for vehicles which burning petrol. Fits All Spark Plug Boots And Wires Up To 1200 Degrees Fahrenhett 648.89 C. Manufacture Part Number SBC BBC 350 454. Compatible Universal fits most straight or angled boots For most hot rods and classics engines, such as 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 engines. Replacement For GM, Replacement For Chevy, Replacement For GMC, Replacement For Olds, Replacement For Cadillac, Replacement For Pontiac, Replacement For Buick, Replacement For Ford, Replacement For Mopar, Replacement For Chrysler, Replacement For Dodge, Replacement For Plymouth. Spark Plug Wire Boot Sleeves look great, helps reduce misfires, Resists damaging chemicals, extends life of wire boots. Non-flammable protects against chemicals resists water, Protect spark plug boots and spark plug wires from Excessive Engine and Exhaust Heat. Keep your spark wire and spark plug cooler in a high temperature environment, Constructed with double layered, they create an effective non-flammable thermal barrier that will extend the life of your ignition wires. Easy Installation Just Slip On Sewn End Over Spark Plug For Maximum Protection, Sleeves Can Withstand Heat Up To 1200 Degrees Using Patented Insultherm Technology.

6 long spark plug heat protector insulating fire sleevePack of 8,12pcs Engine Spark Plug Wire Separator for 8 cylinder vehicles.. LEDAUT spark plug boot cover is made from fiberglass material,it is non-flammable,extreme protect the spark plug boots and wires.. The wire separators great for 8MM9MM10MM wires.used the sprak plugs wire,well protect the wires.. The spark plug wire protector reduces misfires and enhances performance and extends life of wire boots.Universal spark plug boots fits for most angled or straight boots.. Wire separator divider are made of aviation grade aluminum.Durable and light weight.Fixed and organized the engine wires perfectly .makes sprak plugs wire and the engine bay look neat..

Durable MaterialThe Spark Plug Wire Heat Shields are made of two layers of Basalt fiber. It has good high temperature resistance and anti-corrosion effect, and the thermal insulation temperature can reach 2500 degrees.. High QualityThe Spark Plug Wire Heat shield extends lifetime of the wire plugs. Spark plug heat protector both for boot and wire, can protect your expensive plug wire set's performance and increases their life using for LS1 LS2 SBC BBC 350 454.. Compatibility Length 6.1, ID 0.9, it will work with 90 degrees, 45 degrees, and straight spark plug boot heat socks.. Easy InstallationJust slip the large end with the sewn stitching over the boot. Then carefully slip the ringed end over the boot that connects to the spark plug. The other end is covered with a metal circle for easy installation.. Package Included8 pieces. Wear gloves and long-sleeved clothing before installation to prevent glass fibers from falling on your body..

Direct replacement - this spark plug non fouler is designed for easy installation to protect spark plugs from fouling and damage on specified vehicles. Ideal solution - this non-fouler preserves spark plug life and is a reliable replacement for an original non-fouler that has failed due to corrosion. Durable construction - made from quality components to ensure reliable performance and a long service life. Trustworthy quality - backed by team of product experts in the United States and more than a century of automotive experience. Support available - every Dorman part is backed by Dorman's ASE Blue Seal Certified technical support team.

6 long spark plug heat protector insulating fire sleevePack of 8,12pcs Engine Spark Plug Wire Separator for 8 cylinder vehicles.. LEDAUT spark plug boot cover is made from fiberglass material,it is non-flammable,extreme protect the spark plug boots and wires.. The wire separators great for 8MM9MM10MM wires.used the sprak plugs wire,well protect the wires.. The spark plug wire protector reduces misfires and enhances performance and extends life of wire boots.Universal spark plug boots fits for most angled or straight boots.. Wire separator divider are made of aviation grade aluminum.Durable and light weight.Fixed and organized the engine wires perfectly .makes sprak plugs wire and the engine bay look neat..

Multi functional set Spark Plug Wrench T-shaped handle,16mm 58 and 21mm 1316 spark plug socket, providing a complete solution for spark plug disassembly.. Product features The spark plug removal tool is equipped with a foldable 270 handle and a flexible 360 rotating head, making it easy to enter narrow spaces. The T-shaped handle design evenly disperses hand force, anti slip and shock-absorbing, easy to operate and comfortable, efficient and stable.. High quality and durable materials The T-shaped spark plug tool adopts a high-quality carbon steel rod body and anti slip plastic handle, with high hardness and durability.. Widely applicable This spark plug wrench set is suitable for most small engines such as motorcycles, lawn mowers, small motor vehicles, generators, etc. It supports the disassembly and assembly of 16mm 58 and 21mm 1316 hexagonal spark plugs.. Buy With Confidence We prioritize product quality and customer satisfaction. Contact us anytime for support - satisfaction is our promise..

Iridium material. Anti-carbon build up features. Anti-vibration design.

A Must Have for Headers These boots heat sleeve cover is to protect the spark plug wire from direct header heat. Universal fit for most angled and straight boots.. Easy to Install Just slip on sewn end over spark plug for maximum protection. Spark plug wires boots helps prevent burn-through, hardening and cracking of boots. Enhance the performance of the engine, extends lifetime of the wire plugs.. Compatibility Each boot is 6 inch length, boots can go over angled spark plug wires 90 Degree, 45 Degree, And Straight .. Durable Material Spark plug boot cover is made of high temperature resistant glass fiber material and treated with a proprietary coating. It has good high temperature resistance and anti-corrosion effect.. Replace the Part Number SBC BBC 350 454. Fits most hot rods and classics engines including For GM,Chevy,GMC,Ford ect. Package included 8pcs spark plug boots 16pcs stainless steel wire ties..

Country Of Origin United States. Model Number 135-081. Item Package Dimension 5.0 L x 5.0 W x 5.0 H. Item Package Weight 5.9 lb.

MUST HAVE - Smooth 360 Degree Ball Swivel 58 Socket Enhanced with Magnetic Thin Wall Design. 38 Drive Teng x 6-Inch Total Length.. DURABLE - Hardened and Heat treated Chrome Vanadium alloy steel. Constructed and Designed for Spark Plug removal and installation.. LONGEVITY - Fully polished, Chrome plated mirror finish resists corrosion and easy to clean, Knurled shaft prevents slipping. Identifying Laser-etched size.. COMFORTABLE - Magnetic core effectively retains spark plugs and minimizes damage. Maximum flexibility in a tight area with smooth 360-degree action.. 100 RISK-FREE Meet Exceeds ANSI The American National Standard Institute and backed by our Lifetime Limited Warranty for your complete peace of mind..

Complete Spark Plug Maintenance Solution Clean carbon buildup with the pneumatic sandblaster tool and precisely adjust gaps with the universal gap toolextend spark plug lifespan, improve engine performance, and save money on replacements. Professional-Grade Durability Precision Heavy-duty plastic base with brasssteel fittings resists abrasion and rust while the high quality aluminum gap tool ensures accurate measurements 0.04mm-0.88mm range for perfect electrode alignment every time. Universal Compatibility Saves Time Space Works with 12mm-16mm spark plugs across motorcycles, ATVs, lawn equipment, and vehiclesno need for multiple tools wall-mountable design keeps your workspace organized. Proven Safe Efficient Process Compressor-powered sandblasting 90 PSI7.7CFM gently restores plugs without damage included fabric bag contains abrasive media and the gap tools spring-back compensation prevents over-bending. Everything Included Except Compressor Kit includes cleaner unit, 50g silicon carbide, storage bag, feeler gauge and gap tooljust add your air compressor to start maintaining spark plugs like a mechanic.

Fits 7mm 8mm 8.5mm 9mm 9.5mm Spark Plug Wires. 100 Brand New Spark Plug Ignition Wire Separators Holders. This Spark Plug Wires Set includes wrench, convenient to use. Very Simple Easy Way To Clean Up The Engine Bay Keep The Wires From Heat. Package Inlcludes4PCS 4 Hole 4PCS 3 Hole 4PCS 2 Hole And Hardware.

Use for 7mm diameter plug wires. Use for 14mm thread spark plugs. package includes 10 x Spark plug resistor covers.

Package includes you will get 2 pieces of spark plug space tools to meet your long-term needs. Accurate and easy to read the scale range of this spark plug space gauge is from 0.020 to 0.100 inch, and the metric is from 0.6 to 2.4 mm. Quality materials our spark plug space gauge measuring tool is made of zinc alloy, which is tough and durable with clear engraving. Key ring hole there is a small hole on the spark plug space tool that you can string them on the keychain for easy carrying. Easy to store these small spark plug space tools are approximately 1.5 inch 3.8 cm in diameter and are packed in a plastic storage box for easy storage.

Durable Build - Our spark plug gapper is crafted from zinc alloy with a corrosion-resistant finish, providing wear- and scratch-resistant strength that holds its shape through repeated use and varied weather conditions. Accurate Sizing - Our spark plug gap tool features a double-sided engraved scale from 0.0200.100 inches 0.62.4 mm for quick, precise readings that help set optimal spark plug gaps and support reliable ignition performance for cars, trucks, and SUVs. Compact Portability - Our spark plug gap measures about 1.5 inches in diameter and includes a keyring hole so you can attach the tool to a keychain or toolbox for fast access during roadside checks or routine maintenance. Easy Adjustment - Our spark plug gapper tool uses a smooth, polished edge and intuitive pullpress action to widen or narrow gaps without scratching hands or parts, making gap setting straightforward for DIYers and pros alike. Vehicle Compatibility - Our spark plug gapping tool is a universal gauge suitable for most passenger vehicles and light trucks, supplied as a 4-piece set to keep spare gauges handy for regular maintenance and troubleshooting.

Use with 38 Inch Hex Socket or 38 Inch Square Drive. Size M18 x 1.5. Also Works with M18 x 1.5 Spark Plug Threads. Important Use Anti-Seize.

Cleans Spark Plug Threads Spark plug thread repair kit removes dirt and carbon from worn or corroded spark plug holes to help restore proper seating and firing, improving ignition system performance in engines with frequent plug changes.. Two Sizes in One spark plug repair kit features dual ends with 14 mm and 18 mm thread chasers to fit the most common spark plug hole sizes in automotive, motorcycle, and small engine applications.. Works with Common Tools Spark plug rethread kit designed with a hexagonal body for use with standard 1316-inch deep sockets or open-end wrenches, allowing for quick and easy access in tight engine bays.. Rust-Resistant Construction Built from steel with a black oxide finish to resist rust and corrosion, making this spark plug rethreading tool a durable addition to any automotive repair kit or shop toolbox.. Helps Prevent Cross-Threading Realigns damaged threads for smooth plug installation and removal, reducing the risk of cross-threading and costly cylinder head repairs during tune-ups or engine maintenance..

Wide Equipment Compatibility The CMR6H performance spark plugs is designed to standard specifications for reliable performance across major brands power tools or engines. Such as, compatible with Stihl NGK Jonsered RedMax Honda. This interchangeability makes it a convenient maintenance solution for various outdoor power equipment.. Enhanced Material Durability The CMR6H spark plug features a high-strength alumina silicate ceramic insulator for reliable performance under demanding conditions. Its nickel-plated threads offer effective anti-seize properties and corrosion resistance, ensuring easier maintenance and longer service life. These premium materials work together to withstand the rigors of regular use in outdoor power equipment.. Optimized Thermal Performance The CMR6H spark plug features a solid copper core that enhances heat dissipation and electrical conductivity. This design maintains stable operation across varying temperatures while minimizing overheating risks. The broad heat range capability ensures consistent performance in different operating conditions.. Reliable Ignition Performance Engineered with proven technology, this spark plug non fouler ensures quick and efficient starts for your outdoor power equipment. Its consistent performance helps maintain optimal engine operation in trimmers and weed eaters, reducing startup delays and promoting smoother running.. Cost-Effective Value Pack This practical set includes 4 premium spark plugs for long lasting, providing extended replacement coverage for your outdoor power equipment. The new plugs help maintain optimal engine performance, contributing to better fuel efficiency during regular operation. This multi-pack offers convenient long-term savings for equipment maintenance. Before purchasing, please make sure the thread diameter of the spark plug is suitable for your equipment.

Fitment The PQY spark plug gap tool is for most of 14mm 12mm 10mm 16mm standard spark plugs. But not for 18mm thread .. Spark plug gapping tool the tool is made of high quality aluminum with matte texture,allows you to adjust spark plug gap easily and quickly .Just place your spark plug onto the spark plug gapper and then use your desired feeler, then screw the knob slowly until get your desired gap thickness.. Tip for adjusting gap Some spark plugs electrode will spring back when adjust gap. So if your gap target is 0.44mm ,we suggest to use 0.42mm, this way when it spring back you will get it to 0.44mm.. Package include only 1x spark plug gap tool. Attentionthis spark plug gap tool can not work for long reach or short reach plugs spark plugs, please check your spark plugs size before purchase ..

Size Each small engine spark tester features 6 14 shieldcable, 5 shaftlight cover. Suitable dimension to check for spark in even the hard to reach areas.. Material The spark plug tester is made of quality plated shaft , rust and corrosion resistant, internal bulb lasts for years, clear housing is replaceable.. Easy to Use Turn the engine off and remove the spark plug coil. Connect the black plastic leather connector of the spark plug tester to inline spark plug tester. Connect the metal end of this spark plug tester to the spark plug coil. Start the engine. If the light flashes, the ignition wire is intact.. Features The spark tester probe could quickly and easily diagnose ignitionengine outboard motor issues or a fault in the fuel delivery system, this engine ignition coil tester is a must have for any personal, professional machine store and automotive store.. This automotive spark tester is perfect for basic troubleshooting of all internal combustion engines, cars, trucks, motorcycles, lawn mowers, chain saws, trimmers, snow blowers, generators, etc..

High quality material Made of double wall woven glass fiber casing three walls at the suture end, which can form an effective non flammable insulation layer, extending the service life of the ignition wire. There are eight protective covers in a set. Function The spark plug thermal protection sleeve is used for the head heat package of the electric wire, which can extend the service life of the electric wire and plug, also help avoid the boots from burning through, hardening and cracking. Direct replacement, easy to install plug and play, you can directly replace old parts, very convenient, save your time to the greatest extent. Size and Fitment Length615.5cm ID122mm , 8 boot heat shields for use with 90 degree, 45 degree and straight spark plug boots. Note Should you have any questions about the product after purchase, please contact us directly, and we will gladly assist you to resolve all matters.

Precautions for PurchasePlease confirm the compatibility according to the yearmakemodel of your vehicle and the OE number of the replaceable part.. Spark Plug FeaturesBDFHYK spark plugs have superior ignition performance, with faster and more sensitive ignition jumps and significantly improved power performance. Combustion efficiency is fuller, longer service life. Economic service life of 30000-40000 kilometers.. Relive PerformanceOE standard performance and durability TS16949 certified manufacturer. All center electrodes are made from extremely fine iridium electrodes for good ignition performance. Insulators are made from isostatic ceramics for high density, strength, and good insulation.. Compatible Part NumbersSpark Plug compatible to 13292-9499451 F1000-399477-MTR HT15 MOFSP515 PZH-14-F PZH14F SP507 SP546 SP-546.SP515.. Buy with Confidence Exquisite craft,100 new and high quality auto parts,OE level durability..

Universal Fitment Our spark plug gapping tool is compatible with most standard spark plugs, including 10mm, 12mm, 14mm, and 16mm sizes, making it a versatile gap tool for various vehicles. Note It is not compatible with 18mm threads and other long reach or short reach spark plugs. Always verify your spark plug dimensions before purchase for perfect fitment. Durable Material Crafted from high-quality aluminum alloy, this spark plug gap adjuster is built to last. Its robust construction ensures excellent resistance to corrosion and rust, providing reliable performance for all your spark plug gap adjustment needs. Precision Adjustments with Feeler Gauge The included stainless steel feeler gauge offers a precise measuring range from 0.0015 inches to 0.035 inches 0.04mm to 0.88 mm. Combined with our spark plug gapper, it ensures quick and accurate gap adjustments, eliminating the need for guesswork or manual hammering. Effortless Operation with Controlled Results Our spark plug gap tool simplifies the process place your spark plug in the tool, select the desired feeler gauge thickness, and twist the knob for precise adjustments. This controlled approach prevents over-bending and ensures accurate results TipsSome spark plugs will spring back after adjustment, this is a normal physical phenomenon. If you need a gap of 0.03 inches, we recommend that you start with 0.03 inches and watch. If playback occurs, use a smaller gap, such as 0.28 inches. Time-Saving Essential for Spark Plug Maintenance Whether youre a DIY enthusiast or a professional, this gap adjustment tool is a must-have. It is easy to adjust for proper gap, more accurate, saving time and effort compared to traditional methods like hammering or using coins. Achieve perfect gaps with ease and confidence.

Accurate and easy to read the scale range of this spark plug space gauge tool includes 0.040, 0.044, 0.045, 0.050, 0.060, 0.080 inch, and the metric sizes are engraved on the back for clear reading, easy to read. space adjuster the spark plug space tool is located on both sides of spark plug space gauge, which can adjust spark plug space, you can target the tool's slot into the hook of spark plug and pull slightly to make adjustment. Solid construction our spark plug space gauge measuring tool is made of metal, which is durable and reliable to use, solid construction allows for strength and durability, built for resilience and flexibility, engineered to measure clearances of spark plug space size. Easy to store the space adjustment tool measures approx. 1.9 inch 4.8 cm in diameter and are packed in a plastic storage box for easy storage, proper size to use and convenient to store when not in use. What you receive there are 2 pieces of wire spark plug space gauges in this package, enough quantity to meet your daily use and replacement, will bring much convenience to you in everyday life.

Back-Tap Design Repairs M14x1.25 Spark Plug Threads Without Removing The Cylinder Head - Stripped or fouled 14mm spark plug threads This Back-Tap Spark Plug Thread Repair Tool is engineered specifically for M141.25 thread pitch, letting you restore damaged spark plug hole threads from inside the combustion chamber - no cylinder head removal, no heli-coil inserts, no machine shop required. Saves hours of labor and hundreds in repair costs.. Debris Exits With The Tool - Zero Metal Shavings Left In The Cylinder - The biggest risk with conventional thread chasers is metal debris falling into the combustion chamber, causing catastrophic engine damage. Our Back-Tap Style design works in reverse as the tool is pulled outward, it captures and carries all metal shavings and debris out of the bore with it. Apply a small amount of grease to the threading area before use to maximize debris adhesion. Your engine stays protected every time.. Collapsible Design Enters The Bore, Expands Inside, And Repairs Threads From The Bottom Up - Standard thread taps cut from the top down, pushing metal debris deeper into the engine. This tool works differently it collapses to fit through the M141.25 spark plug opening and pass into the combustion chamber. Once inside, the repair zone expands and locks onto the last intact threads at the base of the bore. As the tool is drawn back upward, it re-engages and restores each damaged thread in sequence - working from clean to stripped, inside out in one smooth, controlled motion with no debris pushed downward.. Extreme Hardness - Built To Rethreading Hardness Demands, Made to Last - Spark plug thread repair demands a tool harder than the aluminum cylinder head it's cutting into. This Back-Tap tool is manufactured to extreme hardness specifications specifically engineered to meet and exceed the demands of repetitive thread cutting in engine-grade aluminum. Unlike softer tools that dull after a single use, this tool maintains cutting precision across multiple repair jobs - for professional shops and serious DIYers alike.. Skip The Traditional Thread Taps. Skip The Machine Shop. Get Back On The Road. - Traditional M141.25 spark plug thread repair options mean wrestling with Heli-Coil style insert kits complex, fiddly, high debris risk or pulling the cylinder head entirely expensive, time-consuming. The Back-Tap Style tools eliminates both. M141.25 is the most common spark plug thread size worldwide found across the majority of gasoline-powered cars, SUVs, and light trucks. Compatible with Toyota, Honda, Nissan, Subaru, Hyundai, Ford, GM, and more. If your vehicle runs a standard 14mm spark plug, this tool has you covered.. Package Include 1 pcs 5.27 Inch Long M141.25 spark plug thread repair tool..

Protects electrical connections and wiring from salt, dirt and corrosion. Prevents voltage leaks around any electrical connection. Extends the life of bulb sockets. Required for modern high energy ignition systems.

Complete Thread Restoration The OEMTOOLS 25643 kit includes everything necessary for effective spark plug thread repair, featuring a high-grade tap, 3 inserts, and a specialized installation tool for a comprehensive solution.. Durability and Precision Crafted from premium 18-8 stainless steel wire, this thread repair kit ensures a permanent and wear-resistant thread, making it a trusted tool for automotive, military, and aviation applications.. Time and Cost Efficiency Avoid the expense of major repairs or part replacements with this versatile kit. Capable of restoring stripped threads on non-taper seat spark plugs and suitable for a variety of materials.. Versatile Application Beyond automotive spark plugs, the OEMTOOLS 25643 thread repair kit can rethread alloys, steel, plastics, and magnesium, showcasing its utility in diverse repair scenarios.. Superior Rethreading Performance Designed for ease of use, this kit simplifies what could be a daunting task, ensuring essential threads in spark plug holes are expertly repaired, enhancing vehicle performance..

Start and remove spark plugs in deeply recessed cylinder spark plug holes. Set includes 3 and 6 plug starters. 6 length is designed for coil-on plug applications and other engines with recessed spark plugs. The shorter version is for other applications where space is limited.

Precision Gap Measurement Ensures optimal engine performance with 9 wire sizes from .025 to .060 inches, critical for setting accurate spark plug gaps.. Dual Measurement System Features both inch and millimeter scales, allowing versatile and precise measurement for various vehicle makes and models.. Durable and Portable Design Compact gauge crafted from robust materials, easily fits in your tool chest or pocket for quick access during tune-ups.. Easy-to-Read Indicators The clear and distinct markings on the gauge allow for quick and accurate readings, enhancing your vehicle maintenance efficiency.. Versatile Use Ideal for automotive professionals and enthusiasts aiming for perfect engine tuning and routine maintenance..

Easily install spark plugs in difficult to reach places. 12-inch flexible shaft bends to manuever around cluttered engine compartments. Hand-driven twist knob prevents cross-threading when starting. Universal-fit tool fits most brands and sizes of spark plugs. Saves time and knuckles.

Complete Spark Plug Maintenance Kit this all in one spark plug cleaner kit includes a sandblaster cleaner, gapping tool, fabric cleaning bag, airbag clamp, and detailed instructions, everything needed for professional grade spark plug maintenance in one package. Powerful Carbon Removal System the 7.7 CFM air spark plug cleaner effectively removes tough carbon deposits from spark plugs using included abrasive media, restoring plugs to like new condition for optimal engine performance in motorcycles, lawn mowers, and vehicles. Precision Spark Plug Gapping Tool features an accurate spark plug gap gauge and gapper to properly set electrode spacing, ensuring correct ignition timing and efficiency after cleaning procedures. Durable Professional Constructionthe spark plug cleaner sandblaster built with anti rust brass fittings, steel clamps, and an aluminum base for maximum stability during use The heavy duty materials withstand frequent garage or shop use without wear. Simple Operation Installation spark plug cleaner can easily mounts vertically on walls or posts using side flanges The intuitive design allows switching between abrasive and air cleaning modes with a simple flip of the control lever.

Designed to aide in repairing Two Valve Ford Modular Cylinders Heads. A quality, foolproof repair system that is cost effective and fast. High quality oversized steel alloy insert will repair other inserts that fail and has no ill effects from heat transfer. Total labor time as short as 25 mins, For use on 4.6L, 5.4L and 6.8 V-10 Ford Triton Two Valve Engines. For use on years 1996 to 2003, Part No. 389-100 Replacement Inserts. nsert size m14-1.25, Patented. Ford spark plug insert installer designed to aide in repairing ford modular cylinder heads. Quality, foolproof repair system that is fast, cost effective and simple to use. Used to repair damaged heads from blown spark plugs, with an alloy steel insert. Patented insert is oversized, heavy duty and can be used to replace previously installed inserts that have failed. Includes six inserts saves both time and money.

CTA Tools 3238 Spark Plug Gap Gauge - 9-Wire is designed to accurately measure spark plug gaps. The sizes range from 0.025, 0.030, 0.035, 0.040, 0.044, 0.045, .0.050, 0.055 and 0.060-inches. Heavy-duty construction allows for strength and durability. California Prop 65 - Warning, This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.. Wide range of professional automotive specialy tools. Professional grade. Heavy duty design.

Replaces stripped spark plug threads on aluminum heads with 14mm spark plugs. Installs a new spark plug thread insert in original thread location. For more information check the main Lisle tool- 65000. Replacement part for Lisle tool- 65000.

Tapered edge for gauging spark plugs Specially designed hole with flange adjusts side wire of plug without pressuring center electrode. SPARK PLUG GAPPER. Tapered edge for gauging spark plugs. Specially designed hole with flange adjusts side wire of plug without pressuring centre electrode.

Compatible with Ford Triton use on 4.6L 5.4L 6.8 V-10 Two Valve Engines. For use on years 1996 1997 1998 1999 2000 2001 2002 2003.. Part Number 389-100 Replacement Inserts.. Inside Diameter m14 x 1.25 Outside Diameter 75 -16.. High quality oversized steel alloy insert will repair other inserts that fail and has no ill effects from heat transfer.. Package 2Spark Plug Port Insert. If you have any questions, contact to us freely and we will reply within 12 hours, thank you..

Compatible with Ford Triton use on 4.6L 5.4L 6.8 V-10 Two Valve Engines. For use on years 1996 1997 1998 1999 2000 2001 2002 2003.. Part Number 389-100 Replacement Inserts.. Inside Diameter m14 x 1.25 Outside Diameter 75 -16.. High quality oversized steel alloy insert will repair other inserts that fail and has no ill effects from heat transfer.. Package 4Spark Plug Port Insert. If you have any questions, contact to us freely and we will reply within 12 hours, thank you..

Double-ended for both 14mm and 18mm threads. Cleans threads in spark plug hole. Use with 1316 inch spark plug socket. Shipping weight 5 oz..

ACCURATE SPARK PLUG SETTING Ensure precise spark plug gap setting with the Performance Tool W162C Spark Plug Gauge Gap Tool.. ELECTRODE TOOL INCLUDED The included electrode tool makes it easy to adjust spark plugs to the right gap size.. DURABLE ROUND WIRE BLADES The gauge comes with 7 durable round wire blades in both decimal and metric sizes, ensuring long-lasting use.. SAE AND METRIC SIZES The W162C Spark Plug Gauge Gap Tool has SAE sizes ranging from .020-Inch to .040-Inch and metric sizes ranging from .50 mm to 1.00 mm, making it a versatile tool.. EASY TO USE The Performance Tool W162C Spark Plug Gauge Gap Tool is simple to use and makes adjusting spark plugs a breeze..

The narrow profile and long length allows access to spark plug holes in confined spaces. Package Dimensions 14.478 L x 0.254 H x 4.318 W centimeters. Package Weight 0.100 pounds. Country of Origin United States.

DESIGN CONSIDERATIONS This oxygen sensor rethread tool is designed to re-tap oxygen sensor threads, straightening damaged threads and preventing future cross threading, and it can be used with a 38-inch hex socket.. GET THE JOB DONE Whether youre a professional or a DIY-er, our oxygen sensor rethread tool makes re-tapping threads for oxygen sensor installs a breeze, eliminating cross threaded holes and keeping your vehicle running smoothly. Make sure to use Anti-Seize while using this product.. COMPATIBILITY This oxygen sensor rethread tool works with M12 x 1.25mm Spark Plug Threads.. RELIABLE EFFECTIVE EFFICIENT Users trust ARES to be quality tools. You are backed by our Performance Assurance Limited Lifetime Warranty. If you have any issues with your ARES Oxygen Sensor Rethread Tool, simply contact customer service for troubleshooting help, parts, replacement, or refund.. ASPCA BUSINESS AMBASSADOR We are proud to be part of the ASPCA Business Ambassador Program. If you have a pet, you realize they are more than a pet, they are part of the family. With your support, were proud to help this great organization..

The package length is 1.905 centimeters. The package height is 6.985 centimeters. The package width is 5.08 centimeters. Package Weight 0.027 kilograms.

CompatibleThis universal spark plug boot protector can fit most angled and straight boots.Fits For most hot rods and classics engine including GM Chevy , GMC, OLDS, Cadillac, Pontiac, Buick, Ford, Chrysler, Dodge, Plymouth,such as 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 engines.. FunctionSpark Plug Wire Boot Sleeves look great, helps reduce misfires,Resists damaging chemicals, extends life of wire boots.non-flammable protects against chemicals resists water, Protect spark plug boots and spark plug wires from Excessive Engine and Exhaust Heat.. FlexibleEach Boot Is 6inch Length,Spark plug wire boots will work with 90 Degree, 45 Degree, And Straight Spark Plug Boots.Length615.5cm ID125mm. Easy InstallationJust Slip On Sewn End Over Spark Plug For Maximum Protection ,Spark Plug Sleeves Can Withstand Heat Up To 2500Degrees Fahrenhett. Spark plug boot heat socks, protect your spark plug wire sets performance and increase their lifetime.. CompatibilitySet of 8 spark plug boot protector, Made From Double Wall Braided Fiberglass Sleeving, keep your spark wire and spark plug cooler in a high temperature environment,Constructed with double layered,they create an effective non-flammable thermal barrier that will extend the life of your ignition wires..

PROLONG THE LIFE OF YOUR SPARK PLUGS Are your spark plugs underperforming Clean them up with the ABN Spark Plug Cleaner Pneumatic Sand Blaster Cleaner with Spark Plug Cleaner Abrasive Sand Easily remove carbon build-up for like-new performance and prolonged lifespan Spark Plug Cleaner Tool works with your motorcycle spark plugs, lawn mower spark plugs, vehicle spark plugs and more Always wear protective gear when in use. SPARKPLUG SANDBLASTER CLEANER KIT Includes a spark plug cleaner unit, a fabric spark plug cleaner bag, an airbag clamp, a 1.7 oz .1lb bag of abrasive material, and instructions Spark plug cleaning tool requires mounting hardware, a union fitting, an air hose, and an air compressor that are not included in the kit Spark plug pneumatic blasters feature a 7.7CFM air consumption rating and a 90 PSI pressure rating. BUILT TO LAST Constructed of a thick, durable plastic base with brass fittings, and a steel clamp provides this air spark plug cleaner sandblaster tool with maximum durability and efficiency High-quality materials are resistant to rust and abrasion making them ideal for the abrasive cleaning process 14 inch NPT air inlet with hose barb fits 38 inch air hose. SIMPLE INSTALLATION AND SET UP 2 mounting flanges on each side allow you to mount the spark plug cleaner machine vertically on a wall or post 3.3-inch 8.4cm wide and 8-inch 20.3cm length fits easily and stands 3 inches 7.6cm from the wall when not in use Mount with spark plug insertion facing upwards After filling unit with spark plug cleaner media, secure the 6.3 by 5 inch 16 by 12.7cm cover to the base using the included clamp. EASY TO USE Hook your compressor to the spark plug tool cleaner and insert the spark plug electrode-side down into the rubber cover at the top of the unit Turn on the compressor and flip the switch on your pneumatic plug spark cleaner tool to allow air and spark plug blaster sand to gently swirl and clean out carbon build up on your spark plugs Move plug in a circular motion to allow grit to clean all surfaces When finished, carefully clean remaining grit from the plug.

INCLUDES This thread chaser offers thread repair coverage for spark plugs that require M14 x 1.25 sizes, with a low profile design for access in obstructed spaces.. DESIGN This thread chaser is constructed of premium heat-treated carbon steel and features a black manganese phosphate finish, offering superior durability, longevity, and corrosion resistance.. APPLICATION This thread chaser provides reliable access for thread repair on spark plugs that require M14 x 1.25 sizes. This tool features a 38-inch square drive design, allowing for use with ratchets or other drive tools, and a thin profile circular drive end that offers greater access for confined compartments.. RELIABLE EFFECTIVE EFFICIENT Users trust ARES to be quality tools that make an impact. You are backed by our Performance Assurance Limited Lifetime Warranty. If you have any issues with your ARES Limited Access Spark Plug Thread Chaser Tool, simply contact customer service for troubleshooting help, parts, replacement, or refund.. ASPCA BUSINESS AMBASSADOR We are proud to be part of the ASPCA Business Ambassador Program. If you have a pet, you realize they are more than a pet, they are part of the family. With your support, were proud to help this great organization..

Universal Compatibility This spark plug socket tool is designed to work with a wide range of vehicles, including cars and motorcycles, making it a versatile addition to any toolkit.. Reusable Rubber Insert Features a durable rubber insert that securely grips spark plugs during installation and removal, preventing damage and ensuring a smooth process.. Durable and Portable Made from high-quality materials, this wrench is built to withstand regular use. Its compact and lightweight design makes it easy to carry and store.. Easy to Use Designed for hassle-free operation, this tool simplifies the process of installing and removing spark plugs, saving you time and effort.. Enhanced Grip and Visibility The bright red color provides excellent visibility in your toolbox, while the ergonomic design ensures a comfortable and secure grip during use..

Spark Plug Tool Upgrade -- With the exquisite craftsmanship, the threaded rod is pushed in deeper. A wider range of applications, this new version of our gap plug tool cover 99 of all spark plug on the market. Note that the Feeler Gauge has some oil on it to prevent rusting.. Universal spark plug gap tool -- Compatible with 10mm 12mm 14mm 16mm Spark Plugs, and useful for short thread depth plugs used in chainsaws, string trimmers, and other small equipment engines. A must-have tool for auto repairers. Perfect Father's Day gift.. Precise Distance -- Some spark plugs have electrode gaps that spring back, just using a measurement 0.002-0.004in less than what you are aiming for. For example, If your want 0.016in, we recommend using 0.012in-0.014in so that when it springs back, you get 0.016in. No more hassle, simple and efficient.. How to Use -- Place your spark plug into the gap tool, insert feeler gauge of the gap thickness you want and turn knob until the electrode compressed to the desired gap thickness.. Foldable Feeler Gauge -- Made of 65 manganese steel, each feeler gauge has 32 blades with dual metric and imperial markings and are engraved on the feeler gauge for easy identification, 0.0015 inch 0.04 mm to 0.035 inch 0.88 mm. With a lubricant coating to prevent pitting and corrosion..

Direct replacement - this spark plug non fouler is designed for easy installation to protect spark plugs from fouling and damage on specified vehicles. Ideal solution - this non-fouler preserves spark plug life and is a reliable replacement for an original non-fouler that has failed due to corrosion. Durable construction - made from quality components to ensure reliable performance and a long service life. Trustworthy quality - backed by team of product experts in the United States and more than a century of automotive experience. Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.

GM LS Truck Spark Plug Wire Set, made from highest quality materials to help deliver maximum voltage - ensuring the ultimate performance.. Extremely high EMIRFI suppression along with a very low resistance to help deliver the most spark possible.. Heavy duty 8.5mm diameter silicone jacket to protect the Kevlar spiral wound core from heat, moisture and chemicals.. Made with wire leads that deliver a low 40 ohms of resistance per-foot for maximum EMIRFI noise suppression.. Engineered for high performance engines that need all of the voltage they can get for maximum power output.. 12.5 Inches in Length.

PRECISE GAPPING - Accurately measure and set your spark plugs from 0.02 to 0.1 inches, ensuring peak engine performance, smoother idling, and better fuel efficiency for all your automotive tune-ups.. METRIC VERSATILITY - Easily flip to the metric side for readings from 0.5mm to 2.5mm, making this gap gauge perfect for working on international vehicles or any mechanic's diverse toolkit.. PORTABLE CONVENIENCE - With a handy punched hole design, attach this durable coin-style gapper to your keychain or workshop hook for instant access during roadside fixes or garage projects.. VALUE MULTIPACK - Enjoy three high-quality spark plug gap tools in one affordable set, ideal for sharing with fellow gearheads, stocking your toolbox, or having backups for frequent engine maintenance.. EFFORTLESS READING - Clear, engraved markings on both SAE and metric scales provide quick, reliable visibility, turning complex gapping tasks into a simple, enjoyable process for DIY enthusiasts..

Package Dimensions 3.63 L x 4.25 H x 1 W inches. Package Weight 0.1 pounds. Country of Origin China. Part number 67800.

Affordable Reliable and Built to LastSHINEHOME aims to offer brand new and high quality Replacement Set of 8 Black Spark Plug Wire Boot Sleeves for SBC BBC 350 454 ,Made From Double Wall Braided Fiberglass Sleeving Triple Wall At Sewn End, you will find it is affordable reliable and built to Last, at least you can use for a long time.. CompatibilityFits All Spark Plug Boots And Spark plug boot heat socks Can Withstand Heat rated for 1200F-1800F continuous use, 2500F intermittent.. Product HighlightsEach Boot Is 6inch Length, ID 0.86inch, Boots Will Work With 90 Degree, 45 Degree, And Straight Spark Plug Boots. Easy InstallationJust Slip On Sewn End Over Spark Plug For Maximum Protection ,Sleeves Can Withstand Heat Up To 1200 Degrees Using Patented Insultherm Technology. Package8 Black Spark Plug Wire Boot SleevesNote only fit for vehicles which burning petrol, You Will Enjoy 12 months Once You Order From Us, Any Question You Can Contact With Us Via Email. PLEASE NOTE Only One SHINEHOME Supplier in Amazon. Purchasing from elsewhere will not offer you warranty..

Package includes 12 x Wire Separators. Fit wires with 8-10mm diameter. Material aluminum alloy. Allen key included for easy and fast installation. Make your wires well-organized.

Package include 1x Spark Plug Gap Tool,1x Feeler Gauge. For 10 mm 12 mm 14 mm 16 mm Spark Plugs. NOT compatible with 18mm thread and long reach or short reach plugs spark plugs, please check the size of your spark plugs before purchase. The spark plug gapper makes adjusting the gap quicker and easier. Just place the spark plug onto the gapping tool, choose the desired feeler gauge thickness, and then slowly turn the knob until the side electrode compresses to the preferred gap. For typical physical phenomena, some spark plug electrodes may spring back when adjusting the gap. It is recommended to use a 0.42mm feeler gauge if you want a 0.44mm gap, as using a gauge smaller than the target gap is advisable.. The tool is used to close the gap, NOT open it.

Set Includes WORKPRO Magnetic Swivel Spark Plug Socket Set is 38-inch drive and includes the following 1PC 14mm 4-inch Extension Thin Wall Socket, 1PC 916-inch 6-inch Extension Socket, 1PC 58-inch 4-inch Extension Socket,1PC 1316-inch 6-inch Extension Socket,1PC 58-inch 11-inch Extension Socket, 1PC 916-inch Socket, 1 PC 916-inch Socket. Long and short spark plug sockets can meet your needs in different scenarios. Durable Quality All 38 magnetic spark plug sockets are made of hardened and heat-treated Chrome Alloy steel. Mirror Polish chrome finish on the surface ensures long-time service and against rust and corrosion. Clear size marks on each swivel plug socket are easy to identify. Attention If you are not sure of your spark plug size and don't know how to buy the corresponding size of spark plug socket, you can contact us for confirmation first. Magnetic Core Design Our magnetic swivel socket set is equipped with magnetic core, the magnet retains and protects the spark plug for easier installation, ensures not easy to lose the plug over time, and minimizes damage, so this spark plug socket set can provide years of reliable use. 360 Swivel Design The spark plug has 360-degree swivel action for maximum flexibility, making tight spaces easily accessible. Easier access to the engine compartment, and remove and install spark plug. While the seven sizes give you the extra reach you need for tight spots on a wide variety of applications. Easy to Use The Swivel thin wall socket set has an integrated design and is used for spark plug removal and installation. It doesnt include any accessories. Tightened or adjusted is not needed. It features a 12-point design for enhanced gripping power, knurled grip can help you keep a tight grip to minimize the possibility of slipping in the middle of a job and reduce the chance of hand fatigue.

Set includes58-Inch, 916-Inch, 14mm, 16mm spark plug socket 38-inch Drive With 6-Point and 12-Point, CR-V.. Total Length 4 inch, 6 inch and 10inch, Drive Tang 38 inch. The spark plug tool has 360 degree swivel action for maximum flexibility. Sockets' interior magnets design, retain and protect the spark plug for easier installation.. Special master spark plug socket set for the removal of spark plugs from car, motorbike and other petrol engines. Made of heat-treated Chrome Vanadium steel with chrome-plated mirror finish resists rust corrosion, oil corrosion and easy to clean.. Organized in box for easy carry and storage. Size markings on the socket head for easy identification..

CONVENIENT Perfect Tool for Boosters, Great Gift for DIY Mechanics - Small, portable and solves a real problem.. INSTRUCTIONS Simply put the spark plug in one end and twist the knob at the other to apply smooth, even, and easy pressure to close the gap until the right measurement is found.. QUALITY The easiest way to improve your workbench and boost engine performance - top tier auto performance is constantly evolving, our plug allows you to never have such out dated worries again while setting your spark plug gap. Just set it, forget it, and go enjoy the open road.. FUNCTION Use Professional Race Garage Innovations to Easily Prevent Spark Plug Wire Marks or Nicks for Optimal Spark Plug and Engine Performance.. ENSURE If there is any problem with the product, please do not hesitate to contact us, we will help you solve the problem..

Compatible with Ford 4. 6L, 5. 4L and 6. 8 V-10 Triton Two Valve Engines,For Use On Years 1996 to 2003. Replace Part Number. 389-100. Compatible With cal van 38900 set. Dimensions Inside Diameter m14 x 1. 25 Outside Diameter . 75 -16. Material High quality alloy.

Compatible with 4.6L, 5.4L and 6.8 V-10 Triton Two Valve Engines spark plug threads. For use on years 1996 to 2003. Spark plug Dimensions Inside m14 x 1. 25 Outside 75 -16. Part No. 389-100 Replacement Inserts. High quality oversized steel alloy insert will repair other inserts that fail and has no ill effects from heat transfer..

Direct replacement - this spark plug non fouler is designed for easy installation to protect spark plugs from fouling and damage on specified vehicles. Ideal solution - this non-fouler preserves spark plug life and is a reliable replacement for an original non-fouler that has failed due to corrosion. Durable construction - made from quality components to ensure reliable performance and a long service life. Trustworthy quality - backed by team of product experts in the United States and more than a century of automotive experience. Cost-effective - has similar performance to part that originally came on vehicle, but is priced far below getting replacement from dealership.

Compatible for use with all tools in the engine calibration kit. Now you can put a standard spark plug in the large old style hole. Package Dimensions 12.192 L x 2.54 H x 6.35 W centimeters. Country of Origin China.

COMPATIBLE WITH THESE MODELS Toyota , Lexus ,Scion and Pontiac HS250h 2010-2012 L4 2.4L VIBE 2009-2010 L4 2.4L TC 2005-2010 L4 2.4L CAMRY 2009-2010 L4 2.4L Hybrid CAMRY 2007-2008 L4 2.4L. PERFECT FIT. HIGH QUALITY -These toyota camry coil pack are designed to replace original parts with super easy, safe and seamless installation.. REDUCES COMMON ISSUES -Toyota matrix coil have no hard start, long crank time, power, transmission, shift problems or poor fuel economy issues.. PROFESSIONAL AND RELIABLE -These spark plugs toyota camry are long-lasting build quality to match or exceed OE standard in regards to form and function.. 1 YEAR WARRANTY - If you're not satisfied with your purchase we'll refund or replace the product, no questions asked..

14mm This long reach 14mm adapter allows you to easily work on long spark plug holes. The adapter screws into 14mm spark plug holes..