The Direct Spark Ignition Ignitors, Furnace Burner Igniters Part Number 62-24164-01 622416401. The Replacement of 62-24164-01 Flame Sensor Igniter Compatible with Reheems Water Heaters Furnace.. The 62-24164-01 Direct Spark Ignition Ignitors kit Engineered for reliable performance that ensuring your furnace burner running well and solve some problem for fireplace, fire pit , furnace etc, such as heater was throwing bad ingnitors code blink code.. Design for higher efficiency igniting The Ignitors Spark Replacement Kit is Design for higher efficiency igniting, The Spark Ignition Ignitors kit include a short length of thin metallic rod that creates a small current of electricity in order to confirm there is fire burning within the furnace. As the gas valve opens to begin the combustion process, the current is sent out from the sensor in order to detect the presence of heat from a flame, exceed OEM specifications.. Easy Installation The 62-24164-01 Ignitors with Mounting screws kit as a Assist part is easy for installation, One screw off, one screw on. Replaced in about 5 minutes. Remove the old Sensor and replace it with our new sensor after Shut off the power to your furnace. Please be sure that it is recommended to disconnect the appliance from utilities prior to any repair.. The Direct Spark Furnace Igniters 2-18 Inch Tip x 35 Inch Wire Length, No Special Tools Required, If you have any problem about the 622416401 Ignitors kit, It can be replacedenjoy hassle-free support within 12 months..

MODEL NUMBERSEN01114 Flame Sensor Rod. PART NUMBERSSEN337, SEN0337, SEN441, SEN0441, SEN491, SEN00491, SEN1114, SEN01114, PSE-T19, B340888-2. PREMIUM QUALITY The replacement part is made from durable high quality material and well-tested by the manufacturer. EASY TO INSTALL This flame sensor is a direct replacement for many Trane and American Standard residential furnace models. ATTENTION Please consult your machine manual before ordering to make sure the replacement parts are correct.

Design and Function The flame sensor is specifically designed to detect flames in gas furnaces, ensuring safe operation. Suitable for brands like Kenmore, Amana, and Goodman.Replaces 0130F00010 B1172606 20488501 ACS90453BXA P1257001F P1257007F ACS90703BXA P1257002F P1257008F AP4513976 L38035. Compatibility It fits various models including Fits Model GMS80603AX, GMS80604BX, GMS80603AN, GMS80604BN, GMS80804BN, GDS80403AN, GDS80603AN, GDS80804BN, GDS81005CN, GMSS960402BN, GMSS960603BN, GMSS960803BN, GCSS960402BN, GCSS960603BN, GCSS960804CN, GCSS961005CN, GCSS961205D, etc. Quality and Durability Made from high-quality wear-resistant metals and ceramics, the sensor ensures long-lasting performance and stability, rigorously tested by the manufacturer.. Installation and Safety Installation is straightforward but requires disconnecting power and turning off the air supply beforehand. It helps resolve issues like furnaces shutting off or staying on continuously.. Customer Service and Satisfaction Offers risk-free shopping with a responsive customer service team. If you have any questions, please contact us..

THERMOPILE SENOR ASSEMBLY Thermopile water heater replacement parts are made of high-quality thermoelectric materials and metal alloy materials, which are corrosion-resistant and high-temperature resistant, ensuring that the generated voltage is stable at around 750mv, and adapting to the use requirements of various gas water heaters. Fit for rheem richmond water heater parts to improve the operating efficiency of gas water heaters.. RELIABLE PERFORMANCE Thermopile senor parts, as a key component of the flame safety protection equipment of gas equipment, monitors the gas combustion temperature in real time, maintains a constant temperature, ensures the stable operation of its equipment, and ensures combustion safety. Thermopilewater heaters senor accurately controls the opening and closing of the valve to avoid the risk of ignition failure or accidental flame.. COMPATIBLE MODELS Thermopile gas water heater fit for rheem ruud and richmond water heaters pilot burner. Water heater thermopile replacement part number SP20824, SP20754, SP21058, SP20800, SP21096, SP20739. Gas water heater accessories are suitable for multi-brand and multi-model gas water heaters. Before ordering, please note that the specific compatible model needs to be confirmed according to the actual interface and specifications.. HIGH SENSITIVITY OUTPUT Thermopile assembly has a stable output capacity, ensuring that it will not be damaged for a long time in a high temperature, humid, and gas environment, greatly reducing the frequency of maintenance and replacement, and long service life. The water heater thermopile assembly ensures that it can still maintain performance in a gas environment and humid conditions, and the fast response characteristics can minimize the risk of gas leakage.. INTIMATE SERVICE Thermopile senor assembly structural design is convenient for quick replacement, without the need to disassemble a large number of parts, reducing maintenance time. If you have any questions during the use of fit for rheem ruud and richmond water heaters pilot burner kit parts, please feel free to contact us so as to bring you a good use experience..

62-24164-01 Ignitor is a Direct Spark Ignitor w 35 Lead Wire for Rheem HVAC Equipment and Ru-ud Pro-tech PSE R36 PSER36. Used on Models 80LS, 80PS, SGPN, RGLH, RGLK, RGLL, RGLN, RGLQ, RGLR, RGPH, RGPK, RGPL, RGPN, RGPP, RGPQ, RGPR, RGLE, RGLS, RGLT, RGPE, RGPS, RGPT, SGDG.. Parameter of Ignitor - Length Mnting Flange To Ignitor Tip 2 18 inches, Length Spark Electrode Offset 1 316 inches, Angle Spark Electrode Offeset 83 inches, Length Ground Electrode Offset 1316 Degrees, Angle Ground Electrode Offset 135 Degrees, Spark Gap 18 inches, Wire Length 35 inches, Termination 0.084 inches Dia.. Upgraded - Its compact design makes it suitable for confined spaces, while its rugged construction ensures durability in harsh operating conditions. Provides consistent ignition for gas-fired equipment Direct spark technology eliminates the need for a pilot flame.. Reliable Ignition - The Direct Spark Ignitor automatically sparks and ignites the flame within your gas-fired unit heater. Exceed OEM specifications, ensuring high-quality to keep your equipment running safely and smoothly.. Rest Assured Purchase - Including 2 Pcs Furnace Igniters. This rheem 62-24164-01 ignitor spark supports 365 days return and exchange..

MODEL NUMBER62-23543-01 Furnace Burner Flame Sensor Rod .Snug fit the Rheem Ruud, and Weatherking residential furnace models Furnace. Replace Part 62-23543-01,62-23543-02, 62-23543-03, 62-23543-04. Spec The furnace flame sensor is designed to detect the flame. Termination 14male quick connect,Angle - sensor offset 90 degree.Burner flame sensor 62-23543-01 detects when the burner flame has ignited and sends a signal to the control board to stop the igniter from operating. PREMIUM QUALITY Anti-high temperature,Corrosion resistance.High quality alumina ceramic insulator, High temperature flame rod material. ATTENTION Please consult your machine manual before ordering to make sure the replacement parts are correct.

- - - . If you have any quality problem, please contact customer service in time. Customer satisfaction is our tireless pursuit. 2PACK SEN01114 FURNACE FLAME SENSOR-- The package includes 2 x SEN01114 Furnace Flame Sensor. SEN01114 Furnace Flame Sensor is designed to detect the flame safely. If the sensor does not detect the flame, the gas valve will be closed to prevent the original gas from pouring into your home. When your flame sensor goes bad, the furnace will light for a few seconds, then turn off the safety device of the flame sensor. The Dimension is about 3.4 2.1, the Weight is 0.48 ounces, the Length mounting flange to sensor tip is 2-12. The product is L-shaped, Angle sensor offset is 90 degrees. Termination 14 male thread quick connect. MADE OF HIGH QUALITY MATERIAL-- The 2pcs SEN01114 Furnace Flame Sensor are made high-quality wear-resistant Stainless Steel and Ceramics, prevents cracking and breaking in the process of working or assembling. The product does exactly what it says as long you make sure you measure your dimensions correctly. The color is white and silver. The furnace flame sensor is designed to detect the flame safely. SEN01114 Furnace Flame Sensor can FIX THE SYMPTOMS ?The old burner not detecting the flame, The gas valve is closed, The burner only lasts for a few seconds for you. HIGH COMPATIBLE-- 2PACK SEN01114 Stainless Furnace Flame Sensor Replacement Part for Trane American Standard Furnace replaces part numbers SEN00491, SEN1114, SEN01114, PSE-T19, B340888-2SEN337, SEN441, SEN0441, SEN491. Fit Models ADC1B040A9241AA, ADC1B040A9241AB, ADC1B040A9241AC, ADC1B040A9241AD, ADC1B060A9361AA, ADC1B060A9361AB, ADC1B060A9361AC, ADC1B060A9361AD, ADC1B080A9421AA, ADC1B080A9421AB, ADC1B080A9421AC, ADC1B080A9421AD, ADC1B080A9421AE, ADC1C100A9481AA, ADC1C100A9481AB, ADC1C100A9481AC, etc. . EASY TO INSTALL-- The SEN01114 flame sensor monitors the burner to detect whether or not a flame is present by sending a DC current through the sensor via the flame itself, received by the computer. If your flame sensor goes bad, the main gas burners stay on for only 8 to 10 seconds, then turn off the safety device of the flame sensor, at this time, you need to replace replace the old SEN01114 Furnace Flame Sensor in time. Installing the 2 PACK SEN01114 furnace flame sensor is as simple as removing the old furnace flame sensor and installing a new one. It won't take you much time and at the same time it saves you money.

Temperature sensor for heat pumps. OEM genuine factory authorized part.

Premium Quality Flame Sensor is made from durable high quality material. Ensure long-lasting and high performance.. Function The furnace flame sensor is designed to detect the flame. It also provides direct spark ignition for furnace. A good replacement for Rheem 62-24164-01, 622416401.. Adjustment The rod-ground electrode offset angle is 135 and the spark electrode offset angle is 83 the spark electrode can be bent if adjustments to the installation dimensions are needed.. Easy to install Fix it yourself is simple and cost-effective. Just shut off the power and gas supply to the furnace, then remove the faulty igniter and replace it with our new one.. The flame sensor is a safety component of a furnace located on the interior of the burner assembly. It monitors and verifies whether a flame is burning inside the unit..

- - - . Beaquicy attaches great importance to the shopping experience of each customer. If you have any quality problem, please contact customer service in time. SEN01114 FURNACE FLAME SENSOR-- The package includes 1 x SEN01114 Furnace Flame Sensor. SEN01114 Furnace Flame Sensor is designed to detect the flame safely. If the sensor does not detect the flame, the gas valve will be closed to prevent the original gas from pouring into your home. When your flame sensor goes bad, the furnace will light for a few seconds, then turn off the safety device of the flame sensor. The Dimension is about 3.4 2.1, the Weight is 0.48 ounces, the Length mounting flange to sensor tip is 2-12. The product is L-shaped, Angle sensor offset is 90 degrees. Termination 14 male thread quick connect. HIGH-QUALITY MANUFACTURING-- The SEN01114 Furnace Flame Sensor is made of high-quality wear-resistant Stainless Steel and Ceramics, prevents cracking and breaking in the process of working or assembling. The product does exactly what it says as long you make sure you measure your dimensions correctly. The color is white and silver. The furnace flame sensor is designed to detect the flame safely. Replacing DIY furnace flame sensor can save you the time and money of contacting a high repair service. SEN01114 Furnace Flame Sensor can FIX THE SYMPTOMS ?The old burner not detecting the flame, The gas valve is closed, The burner only lasts for a few seconds for you. HIGH COMPATIBLE-- SEN01114 Flame Sensor replaces part numbers SEN00491, SEN1114, SEN01114, PSE-T19, B340888-2SEN337, SEN441, SEN0441, SEN491. Fit Models ADC1B040A9241AA, ADC1B040A9241AB, ADC1B040A9241AC, ADC1B040A9241AD, ADC1B060A9361AA, ADC1B060A9361AB, ADC1B060A9361AC, ADC1B060A9361AD, ADC1B080A9421AA, ADC1B080A9421AB, ADC1B080A9421AC, ADC1B080A9421AD, ADC1B080A9421AE, ADC1C100A9481AA, ADC1C100A9481AB, ADC1C100A9481AC, etc. . EASY TO INSTALL-- The SEN01114 flame sensor monitors the burner to detect whether or not a flame is present by sending a DC current through the sensor via the flame itself, received by the computer. If your flame sensor goes bad, the main gas burners stay on for only 8 to 10 seconds, then turn off the safety device of the flame sensor. Installing the SEN01114 furnace flame sensor is as simple as removing the old furnace flame sensor and installing a new one. It won't take you much time and at the same time it saves you money.

IMPORTANT NOTE Please carefully check the size and part number of your old parts before purchasing. Use Ctrl F on desktop or the Find in Page function via Rufus on mobile to quickly check your compatible model. You can send us your appliance model number, we can help you confirm if it fits or not. PART NUMBER Package includes 1x LH680014 LH680534 Furnace Flame Sensor, including two separate pieces. Simply connect them together before installation, and your part will be ready to use. This flame sensor ensures the gas valve is only open when there is a flame present, keeping your home safe.. FIT MODELS LH680014 LH680534 Flame Sensor is compatible with Bryant, Carrier, Payne, and Day Night furnace models 330AAV, 330JAV, 333BAV, 333JAV, 398AAV, 58DHC, 58DXC, 58PAV, 58SSC, 58SXC, 58TUA and 58WAV. It replaces part numbers LH680012, LH680014, LH33WZ511, LH33WZ515, and LH33WZ517.. SUPERIOR QUALITY The LH680014 LH680534 Flame Sensor features a durable ceramic insulator that shields the core from heat. Its heat-resistant metal sensor head and rod can withstand extreme temperatures up to 1800F for stable flame detection. The upgraded 73-degree bent design improves positioning in the burner assembly, allowing faster ignition recognition and more reliable furnace performance.. 100 LIFETIME PROTECTION Enjoy reliable performance with our lifetime protection, ensuring that your product will always be covered for any defects or issues that may arise..

High Compatibility The B11726-06 Furnace Flame Sensor is a perfect replacement for multiple models, including B1172606 0130F00010 20488501 ACS90453BXA P1257001F P1257007F ACS90703BXA P1257002F P1257008F AP4513976 L38035 and more.It is compatible with renowned brands such as Kenmore, Amana, and Goodman, ensuring smooth operation of your equipment. Safe Reliable This furnace flame sensor has undergone rigorous testing to safely and effectively detect flames, resolving issues like frequent shutdowns or immediate flameouts after ignition. It guarantees a secure and comfortable home environment. Wide Model Compatibility GMS80603AX, GMS80604BX, GMS80603AN, GMS80604BN, GMS80804BN, GDS80403AN, GDS80603AN, GDS80804BN, GDS81005CN, GMSS960402BN, GMSS960603BN, GMSS960803BN, GCSS960402BN, GCSS960603BN, GCSS960804CN, GCSS961005CN, GCSS961205D, etc. Upgraded Igniter Our B11726-06 Goodman Furnace Igniter is made of high-quality wear-resistant metal and ceramic materials, featuring fast ignition, high-temperature resistance, and long-lasting effectiveness, making it an ideal replacement part for gas furnace sensors. Quality Service Assurance Customer satisfaction is our priority. If you have any questions about the 0130F00010 Flame Sensor or other products, please feel free to contact our customer service teamwere here to assist you.

Precise Flame Detection Ensures safe and efficient operation of your GoodmanAmana or Daikin furnace. Easy Installation Designed for internal mount, fits seamlessly into your heating system. Durable Construction Built to last with high-quality materials for long-term reliability. Push-Pull Output Compatible with a wide range of furnace control boards for seamless integration. Expertly Crafted Manufactured by GoodmanAmana to meet original equipment specifications.

MODEL NUMBER62-23543-01 Furnace Burner Flame Sensor Rod 2packSnug fit the Rheem Ruud, and Weatherking residential furnace models Furnace. Replace Part 62-23543-01,62-23543-02, 62-23543-03, 62-23543-04. Spec The furnace flame sensor is designed to detect the flame. Termination 14male quick connect,Angle - sensor offset 90 degree.Burner flame sensor 62-23543-01 detects when the burner flame has ignited and sends a signal to the control board to stop the igniter from operating. PREMIUM QUALITY Anti-high temperature,Corrosion resistance.High quality alumina ceramic insulator, High temperature flame rod material. MONEY-BACK GUARANTEE For any reason you're not completely satisfied, you can ask for a replacement or refund, no questions asked.

PART NUMBER 62-23543-01 Furnace Burner Flame Sensor Rod 3pack-Designed for the gas HV.AC system. Snug fit the R.heem Ruud, and Weatherking residential furnace models Furnace. If you are not sure if the model is the right one for your furnace, please feel free to contact us and be more than happy to answer your questions. FINE CRASFTMANSHIP Made of high-quality wear-resistant metal and ceramic, durable. Exquisite workmanship, each process is rigorously tested multiple times to achieve long-lasting and effective performance. SUPERIORITY Easy Instal nd cost-effective.You can follow our install process replace the broken sensor easily. Just spend little money to fix your machine. Saves your money from the appliance guyNoteDisconnect electrical power and shut off the gas supply before installing this part. Wear work gloves to protect your hands. FUNCTION The furnace flame sensor is designed to detect the flame. Termination 14male quick connect,Angle - sensor offset 90 degree.Burner flame sensor 62-23543-01 detects when the burner flame has ignited and sends a signal to the control board to stop the igniter from operating. Risk-free shopping, we will provide you with satisfactory solutions. If you are not sure if the flame sensor rod fits, please feel free to contact us or ask a question through Amazon. Customer satisfaction is what we strive for.

PART NUMBER 62-23543-01 Furnace Burner Flame Sensor Rod 2pack-Designed for the gas HVAC system. Snug fit the Rheem Ruud, and Weatherking residential furnace models Furnace.. HIGH QUALITYMade of high-quality and wear-resists metal and ceramics, can last for long.. SUPERIORITYEasy Instal nd cost-effective.You can follow our install process replace the broken sensor easily. Just spend little money to fix your machine. Saves your money from the appliance guynoteDisconnect electrical power and shut off the gas supply before installing this part. Wear work gloves to protect your hands.. FUNCTIONThe furnace flame sensor is designed to detect the flame. Termination 14male quick connect,Angle - sensor offset 90 degree.Burner flame sensor 62-23543-01 detects when the burner flame has ignited and sends a signal to the control board to stop the igniter from operating.. SATISFYING SERVICEFor any reason you're not completely satisfied, you can ask for a replacement or full refund. If you are not sure whether this Flame Sensor Rod correctly fit your appliance, please feel free to contact us or ask a question through Amazon..

SPEC 52W29 Flame Sensor for Len-noxArm-strongDu-cane Furnace .This flame sensor detects the furnace flame to ensure ignition. It then monitors the flame until the furnace is turned off. The furnace flame sensor total lenth is approx 5.3 inch. PERFECT FITThe flame sensor monitors the burner to detect whether or not a flame is present. If the flame sensor is defective, the furnace may not heat.Replacement part numbers,52W2901, 52W29, 31L71, LB-74940A, 31L7101, 28PV41.Fits G40, G41, G50, G51, G60, G61, and G71 furnaces. APPLICATION The flame sensor monitors the flame status of the Len.nox furnace to ensure proper ignition. If the sensor fails to detect a flame, it will immediately shut off the gas valve to prevent unburned gas from leaking into the room. HIGH QUALITY LONG LASTING Len.nox furnace flame sensor replacement made of high quality durable and wear resistant metal, free from harmful chemicals and tested many times by the manufacturer to be safe for use. Improve the efficiency of the furnace and get a longer service life. BUY WITH CONFIDENCE Were confident in the design and quality of this. For any reason you're not completely satisfied with len.nox flame ignitor, or you are not sure whether this replacement part correctly fit your appliance, please feel free to contact us or ask a question through Amazon.

Direct spark furnace ignitors are compatible with the Rheem Water Heaters Furnace Pro-tech PSE R36 PSER36. Furnace burner igniters part number 62-24164-01, 622416401 and 2-Prong electrode assembly replacement for Suburban part number is 232258, with two sparking for fireplace, fire pit, furnace etc.. Furnace burner igniters part number is 62-24164-01, 622416401. Angle-ground electrode offset 90 degree, angle spark electrode offset 78 degree.. Flame Sensor Ignitors design to monitor and verify whether a flame is burning inside the furnace, it can generate sparks quickly and stably to ensure that each action is efficient and smooth, avoiding the failure of ignition and affecting the use of furnace.. 62-24164-01 Furnace burner igniters are made of high quality iron chromium aluminum alloy and heat-resistant materials with high temperature resistance cable which can resist around 480F temperature during working condition.. 62-24164-01 Direct spark furnace igniter is easy install even for beginners, remove the broken Sensor and replace it with our new sensor after shut off the power to your furnace.. 62-24164-01 flame sensor ignitors replacement for Rheem furnace with 232258 2-prong electrode assembly and 31.5 high-temperature rubber cable wire. the round pin terminal diameter of 0.084 inches, the mounting flange to the top of the igniter of 2-18 inches, the ground electrode offset of 1316 inches, the spark electrode offset of 1-316 inches, and the spark gap of 18 inch..

0130F00010 Flame Sensor 2 PACK 0130F00010 Flame Sensor Total length3.8 inchesprobe95 mm used on the gas stove machine to detect the flame and protetct you from gas hazards and close the valve in time.. Goodman Flame Sensor Furnace 0130F00010 Flame Sensor designed for Goodman Amana kenmore brands and replaces part numbers B1172606 B11726-06 20488501 ACS90453BXA P1257001F P1257007F ACS90703BXA P1257002F P1257008F. Flame Sensor for Furnace Models Fit GMS80603AX, GMS80604BX, GMS80603AN, GMS80804BN, GDS80403AN, GDS80603AN, GDS80804BN, GDS81005CN, GMSS960402BN, GMSS960603BN, GMSS960803BN, GCSS960402BN, GCSS960603BN, GCSS960804CN, GCSS961005CN, GCSS961205D, ACEC800403AXAA, ACEC800603AXAA, ACEC800603BXAB, ACEC800804BXAA, ACEC800804BXAB, ACEC800805CXAA, ACSH960905DXAA, ACSH961155DXAA, ACSS920402BNAA, ACSS920603BNAA, ACSS960603BNAA, ACSS960804CNAA, ACSS961005CNAA, APG13240451BB, APD1436080M41AB.. 100 Quality Guarantee 0130F00010 is made from durable high quality metal material for rapid-ignition and have been tested strictly before they are dispatched from the factory to ensure their quality.It ups to the original factory standard even than oem part.. Global Gradse Service LUXRILIX aims for simplicity and excellence in the quality of our services. We hope that you enjoy Online Shopping experience and welcome any comments or suggestions you have. If you are not satisfied with our products, please feel free to contact us for the full refund or new replacement..

Direct spark furnace ignitors are compatible with Rheem for Ruud for Protech Gas Furnace R96VA, R97MV, R97V, R98MV, R98V, R801P, R801S, R801T, R802P, R802V.. Furnace burner igniters part number is 62-24141-05, 62-24164-03. Angle-ground electrode offset 90 degree, angle spark electrode offset 78 degree.. Flame Sensor Ignitors design to monitor and verify whether a flame is burning inside the furnace, it can generate sparks quickly and stably to ensure that each action is efficient and smooth, avoiding the failure of ignition and affecting the use of furnace.. 62-24141-05 Furnace burner igniters compatible with Rheem are made of high quality iron chromium aluminum alloy and heat-resistant materials with high temperature resistance cable which can resist around 480F temperature during working condition.. 62-24141-05 Direct spark furnace igniter is easy install even for beginners, remove the broken Sensor and replace it with our new sensor after shut off the power to your furnace.. Length ground electrode offset is 34, length mounting flange to igniter tip is 1-1516, length spark electrode offset 1-316, spark gap 18, termination 14 inch quick connect, total wire length 40 inch..

Compatible The Direct Spark Ignition Ignitors, Furnace Burner Igniters Part Number 62-24164-01 622416401. The Replacement of 62-24164-01 Flame Sensor Igniter Compatible with Reheems Water Heaters Furnace., ensuring a precise fit and reliable performance.. Replace OE These direct spark ignition furnace burner igniters are ideal replacements for the original part number 62-24164-01, offering an upgraded solution for your heating system.. High Quality Crafted with high-quality materials and featuring a 35' high temperature cable wire, these ignitors are built to withstand extreme heat and provide long-lasting durability.. Function The direct spark ignitors play a crucial role in efficiently igniting the furnace burner, ensuring consistent and reliable operation of your heating system, especially during cold weather.. Installation The 62-24164-01 Ignitors with Mounting screws kit as a Assist part is easy for installation, One screw off, one screw on. Replaced in about 5 minutes. Remove the broken Sensor and replace it with our new sensor after Shut off the power to your furnace. Please be sure that it is recommended to disconnect the appliance from utilities prior to any service or repair..

Applications This direct spark furnace igniter is compatible with the Rheem Pro-tech PSE R36 PSER36. Furnace burner igniters part number 62-24164-01, 622416401.. Superior Quality This direct spark igniter uses resistance heating wire and resistance wire made of ferrite iron-chromium-aluminum alloy. Therefore this flame sensor ignitors is characterized by high resistivity and good oxidation resistance.. Easy Installation 62-24164-01 furnace burner ignitors repalcement is easy to install. After turning off the power to the furnace, the installation is completed by removing the damaged ignitor and replacing the ignitor with one of our new flame sensor ignitors.. Product Specification The direct spark igniter has the wire length of 35 inches, the round pin terminal diameter of 0.084 inches, the mounting flange to the top of the igniter of 2-18 inches, the ground electrode offset of 1316 inches, the spark electrode offset of 1-316 inches, and the spark gap of 18 inch.. Package After Sales 2pcs x Direct Spark Ignition Ignitors. If you have any questions about flame sensor igniter sensing rod fit, you can email us and we will help you within 24 hours..

PART Description SEN01114 Furnace Flame Sensor, Designed to detect the flame safely. When the sensor does not detect the flame gas valve is closed to prevent gas from flowing into the home.FYI The most common problem that we see when a flames sensor is not working properly is The furnace main gas burners ignite, the main gas burners stay on for only 8 to 10 seconds, then the burners shut right back off.. PERFECT REPLACEMENT The SEN01114 American Standard Trane Furnace Flame Sensor replaces part numbers B340888P01, PSE712, SEN0441, SEN441, SEN0337, SEN00491, SEN0337, SEN0491, SEN01114, CARSEN491 and CARSEN1114.. Premium Quality This after-market replacement part is made from durable high quality material and well-tested by manufacturer.Absolutely meet or exceed OEM specificatiand comes in factory sealed parts bag.. COMPATIBLE WITH ADC1B040A9241AA ADC1B040A9241AB ADC1B040A9241AC ADC1B040A9241AD ADC1B060A9361AA ADC1B060A9361AB ADC1B060A9361AC ADC1B060A9361AD ADC1B080A9421AA ADC1B080A9421AB ADC1B080A9421AC ADC1B080A9421AD ADC1B080A9421AE ADC1C100A9481AA ADC1C100A9481AB ADC1C100A9481AC ADC1C100A9481AD ADC1D120A9601AA ADC1D120A9601AB ADC1D120A9601AC ADC1D120A9601AD ADD1A040A9241AA ADD1A040A9241AB ADD1A060A9241AA ADD1A060A9241ABdescription for more models. SHOP WITH CONFIDENCE LUXRILIX is devoted ourselves to provide our customer with quality product and excellent service at a reasonable price, and you can get a free replacement or full refund whatever you are not satisfied.

Termination 14 inch male quick connect. Length mounting flange to sensor tip 2.5 inch. Length sensor offset 1-916 inch. Angle sensor offset degrees 90.

Fits Models DESA Dayton, Knipco, Koehring, Master, Reddy, Remington, Sears, and TSC PP236, M16656-23, M1665623, M16656-24, M1665624, M16656-21. Fits ProTemp, Master, Remington, Heat-Stream, WorkHorse, Heat Hog SunStream 71-016-1010, 710161010. Replace Part 21925, 1PP236-MP4, 1PP236MP4. The wires are 15 in length. Pay attention to see if the end joints match.. Please check whether the accessories you need match.. If your is Heater Photocell Assembly not crystal-clear as glass and is tan or smoky colored or brown CHANGE IT NOW.

FunctionSP21045 chamber sensor replacement kit is designed to restore the functionality of furnaces or other gas equipment. This sensor plays a crucial role in detecting the presence of flames in the combustion chamber, ensuring safe and efficient operation. Kit Includes4 Tinnerman Clip,2 Torx Head Screw - 8 x 34 in. long,1 Hex Nut, 8-32, w External Tooth Lock Washer,2 Pan Head Torx - 1 in,1 Thermistor,1 Instruction Sheet,1 Temperature Probe Assembly, 1 203MW White. Advantages Prevents incomplete combustion and potential hazards Optimizes equipment performance by maintaining precise temperature control Reduce the risks of system failures and unexpected malfunctions. CompatibleCompatible with Rheem and Ruud appliances. Feature Replace the chamber sensors that are faulty or damaged. Ensure accurate flame detection to enhance safety and efficiency.

Packaging Includes 4 Tinnerman Clips, 2 Torx Head Screws - 8 x 34 inch long, 1 Hex Nut, 8-32 with External Tooth Lock Washer, 2 Pan Head Torx - 1 inch, 1 Thermistor, 1 Instruction Sheet, 1 Temperature Probe Assembly, 1 203MW White. Function SP21046SP21045 chamber sensor replacement kit is designed to restore the functionality of the furnace or other gas equipment. This sensor plays a crucial role in detecting the presence of flames in the combustion chamber and is a key component for ensuring the safe and efficient operation of gas water heaters. High Efficiency Compatible with Rheem and Ruud appliances. Replace faulty or damaged chamber sensors to ensure accurate flame detection, thereby enhancing safety and efficiency. Prevent potential dangers of incomplete combustion by maintaining precise temperature control to optimize equipment performance and reduce the risks of system failures and unexpected malfunctions. High Quality SP21046SP21045 chamber sensor replacement kit is an essential component for the effective operation of HVAC systems. This chamber sensor plays a crucial role in controlling and measuring the temperature within the heating chamber, to maintain the efficiency of the furnace or boiler, and the easily installable components can be integrated into various HVAC systems. This sensor is most useful in ensuring strict control of the heating process, thereby improving comfort and energy efficiency. Made of high-quality materials, it is durable, with excellent thermal reflection, insulation, and long-lasting sealing properties. Easy To Install We have provided an installation manual, making it easy to operate. Alternatively, you can watch the installation video on YouTube for the SP21046SP21045 chamber sensor replacement kit.

The flame sensor is a safety component of a furnace located on the interior of the burner assembly. The sensor is a short length of thin metallic rod that creates a small current of electricity in order to confirm there is fire burning within the furnace, As the gas valve opens to begin the combustion process, the current is sent out from the sensor in order to detect the presence of heat from a flame. It monitors and verifies whether a flame is burning inside the unit. Compatible for Rheem 62-23543-01. Termination 14 male quick connect Angle - Sensor offset 90 degrees. Install Process 1.Shut off the power to your furnace or any other appliance. It is very important 2.Remove the broken Sensor and replace it with our new sensor 3.Turn the power back on, Check the Results. Package Includes 1x Flame Sensor Igniter Sensing Rod.

Premium QualityThe 62-24164-01 Direct Spark Ignitor the mounting flange to the top of the igniter of 2-18 inches, the ground electrode offset of 1316 inches, the spark electrode offset of 1-316 inches, and the spark gap of 18 inch, length of 35 inches, the round pin terminal diameter of 0.084 inches. It is made of premium alloy material. Perfect for DIY installation.. Replace Part NumberDirect Spark Ignitors Replacement for model 62-24164-01 Flame Sensor Igniter Sensing Rod of Rheem Furnace Include two sets and replacement for Suburban 232258 2-Prong Electrode Assembly. It is high efficiency spark kit with two sparking for fireplace, fire pit , furnace etc.. Wide ApplicationThis can be universal kit if you can adjust the height of spark pin in right posistion. The two pin will increase the power during spark and higher efficiency igniting. Suitable for RV furnaces, water heaters, indoor and outdoor kitchens, cooktops, ranges and ovens etc.. Easy InstallationThe Direct Spark Ignitor is easy to use. Remember to shut off the power to your furnace or any other appliance, then remove the broken Sensor and replace it with our new sensor. Turn the power back on, Check the Results.. What You GetThe pacakge include 2pcs 62 24164 01 direct spark ignitor with small rubber cables. If you have any questions, simply contact us to get a replacement or refund. We provide friendly 247 customer service..

Replacement Part Number Fit for Rheem SP20172. Widely Applicable Fit for Rheem Ruud, Fit for Richmond water heaters, also fit for AO Smith and fit for Bradford W specific white water heaters models. Flammable Vapor Sensor Film Capable of quickly reacting to gasoline vapors in the surrounding air of the water heater, causing a change in resistance based on the vapor concentration. Function Upon detecting a leak, it quickly triggers the control module to shut off the gas supply to the water heater and prevent ignition, reducing safety risks. Built to strict quality control standards. Package Includes 1x Flammable Vapor Sensor AP13447-3, 1x Cap Plug AP13450-3, and 1x Wire Tie as pictured..

Premium Materials - This furnace heat sensor is crafted from premium wear-resistant metals and ceramics. It has undergone rigorous testing and design improvements, featuring characteristics such as fast ignition, high-temperature resistance, and long-lasting effectiveness, thereby enhancing its durability and stability.. Safety Reliability - This gas furnace flame sensor has undergone a newly upgraded design. It will automatically shut off the gas valve when detecting or failing to detect a flame, resolving issues such as frequent shutdowns or immediate flameout after ignition, ensuring the safety of your home. Broad Compatibility - The B11726-06 furnace flame sensor is an ideal replacement for a variety of models, including B1172606, 0130F00010, 20488501, ACS90453BXA, P1257001F, P1257007F, ACS90703BXA, P1257002F, P1257008F, AP4513976, L38035, and others. It is compatible with well-known brands such as Kenmore, Amana, and Goodman, ensuring the smooth operation of your equipment.Note Remember to cut off the power supply and put on gloves before installation.. Applicable Models - GMS80603AX, GMS80604BX, GMS80603AN, GMS80604BN, GMS80804BN, GDS80403AN, GDS80603AN, GDS80804BN, GDS81005CN, GMSS960402BN, GMSS960603BN, GMSS960803BN, GCSS960402BN, GCSS960603BN, GCSS960804CN, GCSS961005CN, GCSS961205D, etc. Worry-Free Purchase - Customer satisfaction is our top priority. As a responsible seller, we always strive to provide customers with satisfactory products and services. If you encounter any issues after purchasing our flame sensor, we will offer you a satisfactory solution..

Replace Part Number for 62-24141-05. Compatible with Direct Spark Igniter Fits for Rheem GAS FURNACE R921T-ALL R92PA-ALL R92TA-ALL R951T-ALL R951V-ALL R95PA-ALL R95TA-ALL R95TB-ALL R95TC-ALL R96PA-ALL R96TA-ALL U96VA R96VA-ALL U97MV R97MV-ALL U97V R97V-ALL U98MV R98MV-ALL U98V R98V-ALL W95TC-ALL etc. Package included 1 x Direct Spark Igniter. Easy to install Our parts are easy to install. Even without professional skills, you can still use commonly used repair tools to complete the installation. The installation process is quick and easy, saving you time and energy.. High Quality and Durable This accessory is made of high quality material, which is rigorously tested and sturdy. It can be used for a long time, reducing replacement cost and trouble. Note Before installation, please double check if it matches your make, model and year exactly, Avoid installation problems or performance failures due to mismatch.If you have any questions about the product or encounter difficulties during installation and use, please contact our professional customer service team in time, we will be happy to serve you.

Water Heater Sensor Harness Replacement for Rheem AP14720-1 FV Sensor in Rheem water heaters, White. FV Sensor compatibility compatible with various models of Rheem water heaters. and it can also be used in conjunction with Rheem, Ruud, and Richmond water heaters. Safety sensors flammable vapor sensor rheem are made of high-quality PVC and hard plastic. With the addition of a protective shell compared to ordinary connectors, they are more durable and have excellent electrical conductivity, ensuring reliable performance throughout the life of the water heater.. Precision Matching ap14720 vapor sensor, harnesses and connectors, designed specifically for Rheem Sensor Harness AP14720-1 FV, combine precision and durability to ensure reliable, efficient operation. Each sensor harness is carefully crafted to provide a safer, healthier product.. Quality ServiceYour satisfaction is our top priority. We endeavour to provide our customers with excellent serviceWe are committed to manufacturing the highest quality fittingsUsing the best materials and the latest manufacturing techniquesEach product not only combines aesthetics and durability, but also ensures the performance, durability and safety of the product..

Appliance Part 62-23543-01.

Wear work gloves to protect your hands. Burner flame sensor 62-23543-01 detects when the burner flame has ignited and sends a signal to the control board to stop the igniter from operating. Genuine Original Equipment Manufacturer OEM part. Compatible Brands Rheem. This burner flame sensor part number 62-23543-01 is for furnaces. Disconnect electrical power and shut off the gas supply before installing this part.

Quality and value for money Made of durable and wear-resistant metal, free of harmful chemicals for increased efficiency and longevity. Save time and money by not having to spend a fortune to fix your furnace.. Fix Symptom Furnace does not heat. Detects the presence of a flame, and if the sensor does not detect a flame, it will shut off the gas valve, preventing unprocessed gas from dumping into your home..

Quality and value for money Made of durable and wear-resistant metal, free of harmful chemicals for increased efficiency and longevity. Save time and money by not having to spend a fortune to fix your furnace.. Prevents Ignition Failure Helps avoid common furnace issues such as short cycling, failure to ignite, and inconsistent heating.. Reliable Flame Detection Accurately detects the burner flame to ensure proper furnace function and prevent gas leaks.. Direct Replacement for Part Numbers B1172606 20488501 ACS90453BXA P1257001F P1257007F ACS90703BXA P1257002F P1257008F AP4513976 L38035 And it is made exactly fit for most top name brands Kenmore, Amana, Goodman. ??Fit Models GMS80603AX, GMS80604BX, GMS80603AN, GMS80604BN, GMS80804BN, GDS80403AN, GDS80603AN, GDS80804BN, GDS81005CN, GMSS960402BN, GMSS960603BN, GMSS960803BN, GCSS960402BN, GCSS960603BN, GCSS960804CN, GCSS961005CN, GCSS961205D, etc..

This Is A Genuine Oem Replacement Part. Country Of Origin United States. From The Brand Goodman. Number Of Items 1.

Replacement Model4 PC SEN01114 Flame Sensor. The dimension of the SEN01114 flame sensor is 3.4 inch2.1 inch.The flame sensor can also be replaced by other models, SEN0337, SEN0441, SEN441, SEN491, SEN0491, SEN00491, B340888P01,etc. High Quality Our flame sensors are made of high quality wear resistant metals and ceramics and are rigorously tested by the manufacturer. Easy To Install And Cost Saving Our flame sensors are available in a variety of replacement models and are direct replacements for many Tra-ne furnace models. Following our installation procedures makes installation simple and easy, and you can easily replace a damaged sensor to help you save money Before installing, disconnect the power and close the air valve.Before installing the product, turn off the power and wear work gloves to protect your hands. Use Scenario Detects if your burner flame is lit and sends a signal to the control panel to stop the ignition, length mounting flange to sensor tip 2-12. Angle sensor offset 90 degrees. Termination 14 male thread quick connect. Satisfactory Service We have many interchangeable flame sensor models, if you are unsure if this model is right for your unit, please feel free to contact us or ask a question via Amazon and we will be happy to help you and offer you a refund or replacement.

Versatile Replacement Kit This comprehensive kit includes a 2-Pack Flame Sensor Igniter Sensing Rod model 62-24164-01 designed for Rheem furnaces and compatible with Suburban 232258 2-prong electrode assemblies. Perfect for enhancing efficiency in fireplaces, fire pits, and furnaces.. High-Temperature Performance The kit features a 33.5-inch high-temperature cable rated up to 480F, ensuring reliable performance even under demanding conditions. The direct spark ignitor is constructed from D alloy, allowing for operation at temperatures up to 1300C 2370F.. Universal Compatibility This spark kit can be used in any propane or natural gas igniter system, including grills, fire pits, and water heaters. The electrode pin can be bent to adjust the height of the sparking area, accommodating various burner configurations.. Detailed Specifications The direct spark ignitor features a 2-18 inch tip with a 35-inch wire length and a 0.084 inch diameter round pin terminal. Key measurements include a ground electrode offset of 1316 inch and a spark gap of 18 inch, ensuring precise installation for optimal performance.. Easy DIY Installation Designed for easy installation, this kit allows you to fix the ignitor yourself, providing a cost-effective solution. Note that it needs to work with an igniter or control system for successful ignition, making it a straightforward addition to your heating equipment..

Replace Part Number for Rheem SP20172. Fitment for Rheem Ruud, Fit for Richmond water heaters, also fit for AO Smith and fit for Bradford W specific white water heaters models. Flammable Vapor Sensor Film Capable of quickly reacting to gasoline vapors in the surrounding air of the water heater, causing a change in resistance based on the vapor concentration. Function Upon detecting a leak, it quickly triggers the control module to shut off the gas supply to the water heater and prevent ignition, reducing safety risks. Built to strict quality control standards. Package List 1x Flammable Vapor Sensor AP13447-3, 1x Cap Plug AP13450-3, and 1x Wire Tie as pictured. If you encounter any problems with our product, please dont hesitate to reach out to us.

NOTE Please verify your appliance model number before ordering to ensure perfect fit and compatibility. You can use Ctrl F to find your model in our compatibility list. Scroll down to see the full compatibility list and installation video.. PACKAGE INCLUDES 1 x 62-23543-01 Furnace Burner Flame Sensor Rod - Designed for the gas HV.AC system. Snug fit the Rheem Ruud, and Weatherking residential furnace models Furnace. PERFECTLY FIT The 62-23543-01 Rheem Ruud Furnace Flame Sensor is used on the following Rheem, Ruud furnaces where the model number starts with UGDG, RGDG, VGDG, UGDJ, RGDJ, UGFD, UGLG,RGFD,RGLG,UGLH,RGLH,UGLJ,RGLJ UGLK, RGLK,UGLL,RGLL,UGLN,RGLN,UGLQ,RGLQ,UGLR,RGLR,UGPH,RGPH,UGPJ, RGPJ, UGPK, RGPK,UGPL, RGPL, UGPN, RGPN, UGPP, RGPP, UGPQ, RGPQ, UGPR, RGPR, UGRA, RGRA,UGRB, RGRB, UGRJ, RGRJ, UGRK, RGRK, UGRL, RGRL, UGRM, RGRM, UGSA, RGSA,UGTA,RGTA,UGTJ,RGTJ,UGVG,RGVG,UGVH,RGVH,UGVJ. REPLACEMENT PARTS 62-23543-01,62-23543-02, 62-23543-03, 62-23543-04. SIMPLE OPERATIONYou can follow our install process replace the broken sensor easily. Just spend little money to fix your machine. Saves your money from the appliance guyNoteDisconnect electrical power and shut off the gas supply before installing rheem furnace parts. Wear work gloves to protect your hands. SAVING SOLUTION A smart and cost-effective way to fix your furnace without spending hundreds of dollars on a new appliance or paying for costly repair services..

Includes FV Sensor AP13447-3, Cap Plug AP13450-3, and 6 Wire Tie.. HVAC replacement part Rheem SP20172.. RheemRuud replacement FV sensor kit.. This product replaces the AP13447-3 this kit includes this sensor.

Compatible for Rheem 62-23543-01. Termination 14 male quick connect Angle - Sensor offset 90 degrees. Function The furnace flame sensor is designed to detect the flame. A good replacement for Rheem 62-23543-01. Quality Flame Sensor is made from high-quality material. Ensure long-lasting and high performance. Install Process 1.Shut off the power to your furnace or any other appliance. It is very important 2.Remove the broken Sensor and replace it with our new sensor 3.Turn the power back on, Check the Results. Package Includes 1x Flame Sensor Igniter Sensing Rod.

Perfect Compatibility The 52W29 Flame Sensor is compatible with a wide range of furnace models, including 52W2901, 52W29, 31L71, LB-74940A, and 31L7101. It is specifically designed to perfectly fit furnaces from Lennox, Armstrong, and Ducane brands, ensuring the proper operation of your equipment.. Efficient Monitoring This Lennox Flame Sensor effectively detects the furnace flame, providing you with safety assurance. If the sensor fails to detect a flame, it immediately shuts off the gas valve, preventing natural gas leaks and ensuring household safety.. High-Quality Durable Material The 52W29 Flame Sensor is made from wear-resistant metal material, free from harmful chemicals. It undergoes rigorous supplier testing to meet OEM standards, ensuring long-term effective performance, improving furnace efficiency, and extending the furnace's service life.. Cost-Effective Repairing your furnace doesn't have to be expensive. Choosing our Furnace Flame Sensor saves you money. Its easy installation helps you quickly restore your furnace's functionality, saving valuable time.. Specifications This Flame Sensor for Furnace has a total length of approximately 4.8 inches. It is designed for LennoxArmstrongDucane furnaces, monitoring the flame status in real-time to ensure successful ignition and enhance the efficiency of your heating system..

Product introduction AP14720-1-FV replacement sensor harness, brand new, high-quality and unused. Flammable vapor sensor compatibility compatible with various models of Rheem water heaters. And it can also be used in conjunction with Rheem, Ruud, and Richmond water heaters. Product function To maintain the optimal function of the water heater and ensure stable and reliable hot water supply. Rheem flammable vapor sensor is used to detect the presence of flammable vapor near the water heater. This function can effectively prevent flammable vapors from catching fire, thereby reducing the risk of dangerous situations during gas leaks. When the sensor detects flammable steam, it sends a signal to the control unit to turn off the burner, ensuring the safe operation of the water heater. And fast transportation of water heaters will have better results. High quality materials Made of high-quality durable plastic, the wire harness is firmly fixed at both ends. It has been upgraded compared to the original version, adding a layer of protection, durability, and resistance to breakage, which can better withstand the working environment of the water heater and ensure its reliable performance throughout its service life. Perfect Match The water heater flame sensor includes a sensor, wiring harness, and connector, designed specifically for the Rheem AP14720-1 FV sensor, taking into account accuracy and durability to ensure reliable and efficient operation. After replacing this product, your water heater can operate safely and smoothly.. Easy to install The installation of Rheem replacement parts is relatively simple, as it requires connecting the sensor harness to the designated port on the water heater control unit. Proper installation is crucial for the sensor to function properly. If you are not familiar with the components of the water heater, it is recommended to seek technical assistance.

Package Dimensions 7.5 L x 5 H x 0.75 W inches. Package Weight 0.05 pounds. Country of Origin China. Part Number 903600.

Compatible The Direct Spark Ignition Ignitors, Furnace Burner Igniters Part Number 62-24164-01 622416401. The Replacement of 62-24164-01 Flame Sensor Igniter Compatible with Reheems Water Heaters Furnace., ensuring a precise fit and reliable performance.. Replace OE 62-24164-01 and 232258 models have the same specifications, dimensions, and interfaces as original spare parts, and can directly replace aging or damaged igniterssensors. They are compatible with furnaces, fire pits, and other equipment, and the replacement process is simple and efficient.. Function 62-24164-01 adopts 2-Prong 2-pin electrode structure, which provides strong and stable ignition spark, high ignition success rate, avoids equipment startup failure, and reduces the probability of fault shutdown. High QualityEquipped with a 31.5-inch high-temperature cable, the high-temperature resistant material can withstand the high temperature environment during equipment operation and is not easily aged or cracked. Installation The 62-24164-01 Ignitors with Mounting screws kit as a Assist part is easy for installation Remove the broken Sensor and replace it with our new sensor after Shut off the power to your furnace. Please be sure that it is recommended to disconnect the appliance from utilities prior to any service or repair..

Genuine factory OEM original for proper fit, Easy installation and reliability.. replacement for Carrier, Bryant, Payne LH33WZ511, LH33WZ515, LH680012, LH680014. Can be mounted remotely on multiple burners. Can withstand 1800f.

Rheem 47-104184-01 - Water Sensor.

OEM Direct Spark Ignitor. 35 in. Wire Length. 0.084 in. Diameter Round Pin Terminal. Replaces Supersedes? RheemRuud Protech PSE R36 PSER36 62-24164-01 622416401 24164 662766215496 Kanthal and others.

Termination 14 inch male quick connect. Length mounting flange to sensor tip 2.5 inch. Length sensor offset 1-916 inch. Angle sensor offset degrees 90.

Raypak Inc. Part Number 006535F. Catalog Part Number 6239-403. Included components Replacement Part.

Repair and Replacement Solution Used to repair and replace the existing chamber sensor on your Rheem Ultra Low-Nox burner assembly. Complete Kit Contents Includes a high-quality burner door gasket, thermistor, temperature probe assembly, installation instructions and replacement hardware. Genuine OEM Part OEM genuine factory authorized part ensuring quality and compatibility with your Rheem water heater. Ultra Low NOx Compatibility Specifically designed for Rheem Ultra Low NOx ULN gas water heaters for optimal performance. Professional Grade Components ProTech chamber sensor replacement kit features durable components engineered to meet factory specifications.

Precision Safety this thermistor sensor is compatible with AP19299 tankless water heater and boilers. It accurately monitors the combustion chamber's temperature, providing essential data to the system's control board. It can be replaced when the indicator light flashes 9 times. Ideal Fit for Installation we've engineered it to the 11.8 inch length for seamless replacement and equipped it with matching connectors compatible with AP19299 Ultra Low Nox models. This guarantees a direct, plug and play installation, which can restore your water heater's functionality in minutes. Superior Durability built to endure the intense heat and moisture inside your water heater, this water heater sensor parts combines robust brass components with heat resistant plastic housing, which is crucial for resisting corrosion, preventing material degradation, and maintaining structural integrity, ensures you receive stable and reliable performance. Effective a malfunctioning chamber sensor is a common point of failure that can cripple your entire tankless unit. our chamber sensor can address the root cause of shutdowns and inefficiencies, restoring full function, and protecting your home's water heating system. Optimizes System Performance an accurate temperature sensor is key to your heater's performance. Our temperature sensor provides the real time, precise data to regulate the combustion process optimally, which can help reduce energy, while also ensuring a consistent and reliable flow of hot water throughout your home.

Keep your home safe with the 0130F00010 Furnace Flame Sensor 2 Pack, suitable for Goodman and Amana burner models.. Replaces multiple part numbers including AP4513976, 0130F00010, B1172606, B11726-06, L38035, and 20488501.. Detects flame and shuts off the gas valve if no flame is detected, preventing raw gas from entering your home.. Made from wear-resistant materials and thoroughly tested by the manufacturer for quality assurance. Don't forget to disconnect the power and wear gloves before starting the installation.. Need help Our excellent service team is available to answer any questions you may have..

This is a Brand New OEM Upgraded Replacement Flammable Vapor Sensor. Top Quality OEM Replacement Part. Suitable forRheem Ruud and Richmond FVIR Water Heater. Richmond FV Sensor Kit, Suitable for Rheem, Ruud and Richmond FVIR Water Heater.

You will recceive 2 pieces of 62-23543-01 Flame Sensors in one package.. Compatible with Rheem, Ruud, WeatherKing, Thermal Zone and DuroGuard Furnaces.. Replace the follow part codes 62-23543-01,62-23543-02,62-23543-03 and 62-23543-04.. The flange is perpendicular to the terminal and 135 degrees apart from flame sensor end clockwise.. One year product warranty.

You Will Receive 1 pack furnace hot surface ignitor direct replacement compatible with 62-22868-93, 1 pack furnace electrode flame sensor compatible with 62-23543-01, 1 pack limit switch L350 compatible with Rheem Ruud Weatherking Furnaces 47-22861-01 Furnace limit switch compatible with model 47-22861-01, 12 bimetal temperature controls, bimetallic chip contact sensor. Compatible Model gas furnace flame sensor replacement is compatible with Rheem, Ruud, WeatherKing 62-23543-01, 62-23543-02, 62-23543-03, 62-23543-04 furnace replace part Specification mounting flange to sensor tip 2-12, length - sensor offset 1-916, angle - sensor offset degrees 90, termination 14 male connect It is made of quality and wear resists metal and ceramics, and has been well tested by the manufacturer - ensuring lasting and effective performance. Compatible Model furnace hot surface ignitor direct replacement is compatible with Rheem, Ruud, WeatherKing 62-22868-93, 62-22441-01, 62-22548-01, 62-22868-01, 62-22868-02, 62-22868-82, 62-22868-92, 62-22868-93S, 62-22869-01, 62-23460-01, and 8553-5514 furnace replace part Each furnace hot surface ignitor direct replacement come with 1 long insulated wires and 2 high temperature ceramic nuts for splicing. Easy to Install simply strip wires and twist on, installing the igniter furnace igniter replacement takes only a few minutes Simply remove the old furnace igniter and reconnect the new one Wire connections may vary You can use the porcelain wire connectors included with the furnace igniter replacement to cut and splice the wires Unplug before installing the furnace ignitor which is compatible with 025-62-22868-93. Furnace Ignitor Replacement Solve Following Problems furnace won't ignite, furnace keeps shutting Off, pilot light won't stay lit, furnace blows cold air, and furnace makes a clicking noise Furnace replacement ignitors are designed to extend the life of your furnace and is easy to install.

Function A flame sensor senses the furnace flame ensuring that ignition has occurred. It then monitors the flame until the furnace shuts down. Should combustion be disrupted for any reason, the sensor loses its signal and shuts the gas valve off, ensuring the safety of your home.. Materials This flame sensor for furnace is crafted from premium wear-resistant metals and ceramics.It is resistant to high-temperature oxidation and corrosion, which extends its service life and makes it suitable for harsh combustion environments.. Package You will receive 1 piece flame sensor. The total length of the flame sensor is 3.7 inches.. Compatibility This flame sensor is a replacement for Intertherm, Nordyne, Miller, Tappan, Gibson, Frigidaire part 632484.. Installation Use work gloves and safety glasses during installation to protect yourself. Steps 1 Remove the furnace access panel 2 Disconnect the sensor wire and unscrew the mounting bolt 3 Install the new sensor with wire connection 4 Secure tightly for proper grounding and restore power..

Not exact Replacement of model 62-24164-01 Flame Sensor Igniter But you can do modifiction on mounting holes. Sensing Rod for Rheem Furnace Include two sets and Replacement for Suburban 232258 2-Prong Electrode Assembly, this is high efficiency spark kit with two sparking for fireplace, fire pit , furnace etc. DIY Ignition Parts with Double Sparker and 33.5inch 480F Resistance High Temperature Cable.COMPATIBILITY Direct replacement part designed specifically for Suburban SW series RV water heaters, ensuring proper fit and function. Also can be used for any propane or natural igniter system like grill, fire pit and water heater if you can adjust the height of the sparking area to fit your burner.The electrode pin can be bended if you need adjust the installation size. Model Compatibility The RV water heater fits for SAW6D ,SAW6DE,SAW6DEL,SW10D,SW10DE,SW10DEL,SW10DEM,SW10DM,SW10V,SW10VE,SW12D,SW12DE,SW12DEL,SW12DEM,SW12V,SW12VE,SW16D,SW16DE,SW16DEL,SW16DEM,SW16V,SW16VE,SW4D,SW4DE,SW6D ,SW6DE,SW6DEL ,SW6DEM,SW6DM. This kit need to be worked with igniter or control system to ignition..

HVAC CONTROLS. When the flame sensor goes bad, the furnace will light for several seconds and then turn back off on the flame sensor safety. This is a Brand New Furnace Flame Sensor.

Termination 14 inch male quick connect. Length mounting flange to sensor tip 2.5 inch. Length sensor offset 1-916 inch. Angle sensor offset degrees 90.

Reliable Safety ProtectionFlammable Vapor Sensor Film Capable of quickly reacting to gasoline vapors in the surrounding air of the water heater, causing a change in resistance based on the vapor concentration. Direct Replacement for SP20172 AP13447-3 25VSThis flammable vapor sensor kit is a direct replacement for part numbers SP20172 and AP13447-3 25VS, restoring normal operation when the original sensor fails.. Wide Compatibility Compatible with select Rheem, Ruud, and Richmond FVIR gas water heaters. Ideal for residential gas water heater safety system repairs. Please verify model compatibility before purchase.. Complete Sensor Kit IncludedIncludes flammable vapor sensor, protective cap, and necessary components for straightforward replacementno additional parts required.. Durable Easy InstallationManufactured with heat-resistant and corrosion-resistant materials for long-term reliability. Simple plug-in installation helps reduce downtime and service costs..

The kit includes a Flammable Vapor Sensor AP13447-3 - 25VS, a Cap Plug, and a Wire Tie. It is compatible with Rheem Ruud, Richmond FVIR water heaters, as well as certain models of AO Smith and Bradford White water heaters. For any questions or compatibility inquiries, feel free to consult with us. Flammable vapor sensor film Capable of quickly reacting to gasoline vapors in the surrounding air of the water heater, causing a change in resistance based on the vapor concentration. Quick response Upon detecting a leak, it quickly triggers the control module to shut off the gas supply to the water heater and prevent ignition, reducing safety risks. No external power required It relies solely on the small amount of power provided by the control circuit to read the sensor's resistance changes and perform subsequent processing. Fixing the water heater issue After replacing the sensor, the water heater quickly started working again and hot water was restored.

WIDE COMPATIBILITY Direct spark furnace ignitors are compatible with the Rheem Water Heaters Furnace Pro-tech PSE R36 PSER36. Furnace burner igniters part number 62-24164-01, 622416401 and 2-Prong electrode assembly replacement for Suburban part number is 232258, with two sparking for fireplace, fire pit, furnace etc.. FUCTION Flame Sensor Ignitors design to monitor and verify whether a flame is burning inside the furnace. The flame sensor is a safety component of a furnace located on the interior of the burner assembly, can be universal kit if you can adjust the height of spark pin in right posistion. The two pin will increase the power during spark and higher efficiency igniting. We also include two piece of small rubber cable piece to gather the wire during using.. PREMIUM QUALITY Furnace burner igniters are made of high quality iron chromium aluminum alloy and heat-resistant materials with high temperature resistance cable which can resist around 480F temperature during working condition.. EASY TO INSTALL 62-24164-01 Direct Spark Furnace Igniter is easy install even for beginners, remove the broken Sensor and replace it with our new sensor after shut off the power to your furnace. Direct spark furnace igniter flame sensor sensing rod -ground electrode offset is 135 degrees, spark electrode offset is 83 degrees. The electrode pin can be bent if you need to adjust the installation size.. PACKAGE INCLUDES 2 pack 62-24164-01 flame sensor ignitors replacement for Rheem furnace with 232258 2-prong electrode assembly and 31.5 high-temperature rubber cable wire. the round pin terminal diameter of 0.084 inches, the mounting flange to the top of the igniter of 2-18 inches, the ground electrode offset of 1316 inches, the spark electrode offset of 1-316 inches, and the spark gap of 18 inch..

Replacement model62-23543-01,62-23543-02,62-23543-03,62-23543-04. Applicable circumstancesDetect when the burner flame ignites and send a signal to the control panel to stop the ignition. Length mounting flange to sensor tip 2-12, length-sensor offset 1-916. Angle sensor offset 90 degrees. Termination 14 male thread quick connect.. Excellent quality made of high quality and hard wearing metals and ceramics, well tested and durable.. Easy to install, cost-effective You can easily replace damaged sensors by following our installation process. Help you save equipment costsBefore installing this component, disconnect the power and turn off the air source. Wear work gloves to protect your hands.. Satisfactory service For any reason you are not completely satisfied with the product, you can ask for a replacement or a full refund. If you are unsure whether this flame sensor stick is suitable for your device, please feel free to contact us or ask questions through Amazon..

Duralight Two Year Replacement Warranty. Restores Reliable Operation. 90 Degree Bend Angle - Ceramic Length 1-12. 14 Quick Connect Terminal. Direct Replacement for Rheem - Ruud - Weatherking - Comfort Aire - Century Part Numbers 62-23543-01 and 62-23543-03.

This flame sensor is for Rheem Ruud gas furnace, work with Rheem classic 90 plus, Rheem criteron II gas furnace etc. For more fitment, pls check the description part.. Easy to install and works well. Exact replacement for the part 62-23543-01, 62-23543-02, 62-23543-03, 62-23543-04. Made from durable and resists wear material, and well-tested by the manufacturer before shipment. Package includes 2 pcs furnace flame sensors. We provide excellent service and please contact us if you have any questions.

This is a Brand New Furnace Flame Sensor. When the flame sensor goes bad, the furnace will light for several seconds and then turn back off on the flame sensor safety.

Part Number62-23543-01 Furnace Burner Flame Sensor.2PackPart Number62-23543-01 Furnace Burner Flame Sensor.2Pack. Made of high-quality and wear-resists metal and ceramics.. This flame sensor is a direct replacement for many Rheem, Ruud, and Weatherking residential furnace models.. Easy InstallFix it yourself is simple and cost-effective.. If you are not sure if part is correct, ask us We are always happy to help Please Contact Us..

This is a Brand New Furnace Flame Sensor. When the flame sensor goes bad, the furnace will light for several seconds and then turn back off on the flame sensor safety.