NoteOur clutch is suitable for engines with a 34 19.05mm aperture, but not for generators with a 0.787 20mm aperture.. Suit for 34 Bore 12 Tooth Centrifugal Clutch with 4 Ft 35 Chain, Common Clutch for 2-6.5 HP Engines using 35 Chain, Engagement Speed 2300300 RPM.. Compatible with This Clutch kit is compatible with Honda Honda cloned engines GC160, GC190, GX120, GX140, GX160, GX200. Also fit for Harbor Freight Greyhound 196cc and Harbor Freight Predator 212cc.. Tips Also fits for most 5.56.5 HP clones, 4-6.5 motors in all brands and any other engines with 34 crank shaft and 316 key way. For Briggs Stratton and 2 - 6.5 HP with 34 Shaft. For Tecumseh Engines 2 -6.5 HP with 34 Shaft. Installation TipsBefore installation, you need to drop a circle of lubricant above the snap ring and wait for it to penetrate, you can rotate it without any obstruction please refer to the picture for the exact position.. Pre-use test When the clutch is just installed and started to run, it needs 3-5 times to break in. The method is as follows, first, no load running to the clutch first engagement, keep it for 10 seconds and then turn off the engine to cool down second, load gradual 3 times from 0 to full speed, each interval of 2 minutes to cool down. If there is no problem after these two steps, you can avoid the problem that insufficient speed will cause the clutch internal dumping block and clutch shoe, and insufficient contact area will lead to slipping and friction smoke.. Note Centrifugal clutch designed to be used on one wheel karts with rear tires 15 tall, and engines 2hp-6.5hp.. Package including1 x Centrifugal Clutch, 1 x 4 Ft 35 Chain, 2 x Set Screws and 1 x Connecting Link..

Fitment Flywheel remove tool is for most flywheels with steel adjustable timing hubs, PVL clone flywheel and raceseng flywheel with puller hole. Applicable Engine Predator 6.5hp 212cc OHV horizontal shaft gas engine not for hemi engine, GX160 GX200 6.5hp clone engine, for Harbor Freight. Compatibility Coleman CT200U CT200U-EX BT200X, KT196 CK196-T mini bike go kart, Axis M200, Massimo MB200, Trailmaster MB200, Baja Warrior MB165 MB200. Good Flywheel Remove Tool Compared with hitting the crankshaft with a hammer, using this tool to remove the flywheel is more convenient, labor-saving and avoiding damage to the crankshaft and flywheel. Installation Notices 1. Install the threaded screws into clean and lubricated puller holes, be sure to thread screws in fully. 2. Tighten the nuts evenly back and forth in 12 turn increments until the flywheel pulls off. 3. Stubborn flywheels may require that you hit the center of the puller block with a hammer once significant pressure is applied by tightening the nuts. Be careful not to strike the threaded rods and never hit the flywheel itself with a hammer. Note Pls check installation pictures if have problems on installation.

CompatiblityPredator 212 carburetor Kit for the most mini bike, Coleman ct200u bt200x GX160 GX200,Predator 196cc 212cc 224cc engine Intake Connection.. High Quality MaterialPredator 212 engine parts are made of aluminum alloy, while NIBBI Strengthens the Intake Manifold to Resist Corrosion and Robustness,Guaranteeing Motorcycle Stability.. Precision DesignThe Predator 212 Intake is Precision Engineered with Perfectly Matched Holes,Perfect for NIBBI PE24 Flange Carburetor Install and Enjoy a Performance Boost.. Easy InstallationThis kit includes not only the NIBBI carburetor but also an air filter and intake manifold. With everything you need in one package, installation is simplified, and you can get back to riding faster.. Serviceplease check for the details and size to make sure this part will fit. If you have any questions, kindly contact us any time and we will be able to help you out..

JMCHstore Chrome Recoil Fan Cover Shroud Housing for Coleman CT200U CT200U-EX BT200X Mini Bike TrailMaster MB200-2 Minibike, Realtree RT200 196cc Mini Bike, Axis M200 offroad bike. For 2023 Coleman B200 B200RS B200RSV B200R B200C B200V 200CC Tao Motor Mini bike. For Predator Non Hemi 212CC Ghost Engine Hisun 196cc Engine Honda GX160 GX200 Engine DO NOT FIT MAX 224 ENGINE. Brilliant Chrome Style. Draws Superior attention to your mini bike or racing go-kart Not only does it look stunning, but it also adds a layer of protection against corrosion and wear, ensuring it stays looking awesome for longer. It has reach Mirror look w pre-polish.. Protective Housing Prevent debris from contacting the flywheel and flywheel fan, including appendages that would result in injury.. Efficient Cooling The design aids in efficient cooling of the engine, allowing it to maintain its performance even under intense usage..

Fitment Fit for Predator 212cc 196cc 224cc Non Hemi Ghostnot for hemi engine,Honda GX160 GX200 6.5hp clone engine,Tillotson 212cc,Fitment Fit for Predator 212cc 196cc 224cc Non Hemi Ghostnot for hemi engine,Honda GX160 GX200 6.5hp clone engine,Tillotson 212cc,. Upgrade Aluminum Flywheel 10krpm for Predator 212cc 196cc 224cc 6.5Hp for Honda GX160 GX200 Flywheels for Generator Engine Mini Bike Parts Motor. Flywheel for Predator 212cc NON Hemi, 224cc New Ghost 212cc engine,for Honda GX200, Clone 196cc BSP Tillynot fit the hemi predator engine 69730 69736. Regarding the flywheel It should be emphasized that the flywheel is made by mold casting, so there are corresponding edges and corners on the surface. It looks like cracks, but in fact, it is not, and it does not affect the service life.. luminum Flywheels We are committed to providing the best parts selection and quality for your outdoor power equipment. Package Include1Aluminum Flywheel. Not fit the hemi predator engine.

FitmentAluminum Flywheel compatible with Non-hemi Harbor Freight Predator 212cc 196cc 200cc 224cc 69730 69736Compatible with Honda gx160 gx200 flywheel partsCompatible with Coleman CT200U BT200X CT200U-EX,Baja Warrior MB200 MB165, Massimo MB200 MB165 mini bike and KT196 go kart. Durable and stable The 212cc flywheel is crafted from premium aluminum alloy, ensuring robust construction and resistance to damage. It offers excellent durability alongside superior heat resistance, guaranteeing an extended service life. High rotational speed and Better Acceleration This aluminum flywheel enables the engine speed to instantly surge to 10,000 RPM.Significantly boosts the engine performance of mini bikes and karts, delivering an unparalleled riding experience.Additionally, the 196cc flywheel features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC. NoteWhen unpacking, you may notice some raised areas on the flywheel surface. Please do not be concernedthis is a result of the integral casting process during manufacturing. You may use it with confidence. Package1212cc aluminum flywheel1M14 flywheel Nut1crankshaft flywheel key.

FunctionFit for Predator 212cc. InstallationYou can find installation instructions on websites such as YouTube. MaterialsMade of Aluminum. NoteWe provide product sales, and buyers can search for usage videos for product usage. SupportAny questions can tell us.

compatible withSuitable for go kart engines on mini bikes powered by non-hemi predator 212cc, 196cc, 224cc 6.5hp performance parts such as powerhorse GX160, GX200, Coleman CT200U, CT200U-ex mini bikes, KT196 go karts, Massimo MB200, Baja Warrior MB165, MB200 mini bikes, 69730, and 69736 motors.. MATERIALS OF SUPERIOR QUALITY - The upgraded flywheel is crafted from premium billet aluminum, with strict material control to ensure its strength. It is manufactured adhering to stringent standards, guaranteeing the most dependable performance. The flywheel center hub is sturdy and resilient, protecting against damage to the taper, fixed keyway. Additionally, the center hub features threaded holes for enhanced durability and long-term usage.. ENHANCED PERFORMANCE AND STABILITY - Equipped with a high-strength, multi-zone rare earth magnet, it generates a more powerful and enduring spark. By advancing ignition timing, it maximizes the utilization of every drop of fuel, resulting in increased engine output and improved transmission performance. The larger spark curve it creates facilitates greater horsepower and ensures stable operation even at high speeds.. PACKAGE INCLUDED1 x aluminum flywheel1 x metal flywheel crankshaft key. Professional after-salesWe sell professional parts and provide free technical support. If you have any problems or dissatisfaction after receiving the products, please contact us directly to get New Replacement or Return..

Fitment Only For Predator 212cc Hemi. Ultra-High RPM Flywheel Specifically engineered for the Predator 212 Hemi engine, designed to safely handle rotational speeds up to 10,000 RPM for maximum performance.. High QualityThe flywheel is made of high quality aluminum material, strong strength and wear-resistant to ensure reliable performance.The center hub is sturdy to prevent damage to the taper, fixes the keyway, center hub also has threaded holes,durable and can be used for a long time.. Enhanced Safety Machined for good balance, reducing vibration and the risk of failure at high speeds, while improving engine efficiency.. Package Include1Aluminum Flywheel.

Fitment Only For Predator 212cc Hemi. Sturdy Durable The flywheel is made of high-quality cast aluminum material, with the function of sturdy, heavy-duty, and wear resistance, ensuring the most outstanding engine. Not like metal flywheels, aluminum flywheels can better dissipate heat during operation which helps the engine under normal operating temperature.. Good Performance The 212 hemi flywheel is constructed of high-strength to withstand high RPMs and heavy loads. Its precision-balanced design reduces vibration, improves engine stability and maximises power output. The excellent motor speed of up to 10000 rpm allows your vehicles to rev quicker and more powerful.. Note Designed to match OEM specifications, this flywheel is easy to install without requiring additional modifications. Whether youre a DIY enthusiast or a professional mechanic, youll appreciate the hassle-free setup.. Package Include1Aluminum Flywheel.

FitmentFor Predator 196cc, 212cc NonHemi Cast ,For Honda GX200. Premium Billet Construction Crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Blue Finish Sleek and stylish,complementing your vehicle's interior.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Timing is 32 degrees with stock key..

Fitment This super 30 series driver is designed to be used on many Mini Bikes , Go Karts and small clone engines with 34 bore shaft . Mini Bikes Coleman CT200U, BT200X,CT200U-ex, Baja MB165 MB200 Warrior,Heat, Mini Baja, Massimo MB200, Realtre RT200, Axi M200, Trailmaster MB200, Meg Moto 212. Go Karts KT196, Yerf Do, Manco, Murray. Small Clone engines Predator 212cc 196cc 224cc 225cc 6.5hp hemi ghost, Tillotson 212cc, Bil Hard 212,Duroma 7hp 212cc,Hisu 196cc,Hond GX160 GX200. High Quality Material The super 30 series driver clutch kit is made of high quality metal material, which is strong, durable, not easy to deform. Maximum torque makes more wear-resistant, fast heat dissipation. Once the clutch is installed, it can withstand pressure caused by friction and works perfectly. Its easy to install and a good replacement. Higher RPM Excellent Performance The 30 series driver has the advantages of quick accelerationhigh RPM, smooth quiet engagementless belt slip, excellent power deliverymore torque and easy installation. It improves a lot in terms of performance and reliability compared with the stock driver. The 2035895959 go kart drive belt is made of high quality rubber,having the characteristics of heat and corrosion resistance ,which is sturdy and durable in use and is a perfect replacement when you need. Smooth Engagement Responsive This clutch binds at 2000200 RPM and engages almost instantly with no more lag. Our upgraded torque converter provides more torque and smooth acceleration than conventional clutches, and is even capable of allowing your belt to ride several times farther than before. The torque converter parts support up to 8 horsepower, accelerating throughout the RPM range with more responsive throttle.. Package Included1 x 30 Series Torque Converter Clutch.

Fitment For Predator 212cc Hemi Remind will fit the hemi predator engine. Solve disassembly problemsUpgraded 212cc Hemi 10krpm Flywheel with puller hole by using puller hole can be easily disassembled,simplifying the maintenance and repair process.. Solving The Power Problem The 212cc Hemi 10krpm Flywheel adopt fin design that creates minimal air drag .Helps your motor to rev quicker while still moving enough air for cooling.. Corrosion resistance and Heat Resistant Upgraded 212cc Hemi 10krpm Aluminum Alloy Flywheel is made of high quality sandblasting and passivation aluminum instead of the original iron and plastic material, strong and lightweight, corrosion resistance, protection performance, heat resistance to ensure the great performance.. Package Include1Aluminum Flywheel.

Wide Compatibility For Predator 212cc 224cc non hemi ghost 208cc 69730 69736 GX160 GX200 196cc BSP Tilly Clone engine. Not Fit For Predator Hemi Engine.For Coleman CT200U BT200X CT200U-EX, Baja Warrior MB200 MB165, Massimo MB200 MB165 mini bike and KT196 go kart.. Ultra-Lightweight DesignWeighs only 3.3 lbs, significantly lighter than stock cast iron flywheels. Dramatically reduces rotating inertia for quicker throttle response and faster RPM acceleration.. High Strength Heat Resistant Our predator 212 flywheel is made of high quality cast aluminum instead of the original iron and plastic material, strong and lightweight to ensure the great performance. In addition, the center hub is equipped with strong and durable thread holes, which can keep the taper from getting damaged and fix the keyway.. Solving The Power Problem The 212cc flywheel features an ultra-low drag fine design that will greatly reduce air drag on your racing engine while still moving enough air for cooling. Less air drag on the flywheel means more power freed up throughout the power curve especially on an excellent speed up to 10,000rpm, make your engine work like a charm with faster and smoother running, better acceleration..

Fitment Specifically for Predator 212cc Hemi engines Model 60363. Engineered for Mini Bike and Go Kart performance upgrades. Note Does NOT fit Non-Hemi engines.. Easy Removal Features upgraded threaded puller holes. Simplifies maintenance by allowing easy disassembly with a standard puller, preventing damage to the crankshaft or flywheel taper.. High-Speed Performance Rated for 10,000 RPM. Precision-cast aluminum with a streamlined fin design reduces air drag and ensures rapid engine acceleration while maintaining optimal cooling.. Advanced Finish Made from high-quality aluminum alloy with Sandblasting and Passivation. Superior to OEM ironplastic offers exceptional heat resistance and corrosion protection in harsh conditions.. Package Includes 1 x Aluminum Flywheel. Direct replacement part designed for high-performance stability and reduced engine vibration..

FitmentFor Predator 196cc, 212cc ,For Honda GX200. Features an advanced timing of approximately 32 degrees.This advancement ensures the spark plug fires earlier, maximizing combustion efficiency, resulting in higher RPMs and a noticeable increase in horsepower and throttle response.. All billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Features a rare earth neodymium magnet. Each flywheel is precision balanced to reduce vibration and withstand the stresses of high-performance applications.. Flywheel weight 3.33lbs..

FitmentFor Predator 196cc, 212cc NonHemi Cast ,For Honda GX200. All billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design. Features a rare earth neodymium magnet. Each flywheel is spun balanced. Timing is 32 degrees with stock key.Flywheel weight 3.33lbs. The new billet flywheel for the Predator 212 NON-Hemi has an ultra low drag fin design that will greatly reduce air drag on your racing engine, while still moving enough air for cooling. Less air drag on the flywheel means more power freed up throughout the power curve, especially on the top end. This flywheel is designed for oval track racing..

FitmentFor Predator 212cc Hemi Only. Features an advanced timing of approximately 32 degrees.This advancement ensures the spark plug fires earlier, maximizing combustion efficiency, resulting in higher RPMs and a noticeable increase in horsepower and throttle response.. All billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Features a rare earth neodymium magnet. Each flywheel is precision balanced to reduce vibration and withstand the stresses of high-performance applications.. Flywheel weight 3.33lbs..

FitmentFor Predator 212cc Hemi Only. All billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design. Features an advanced timing of approximately 32 degrees.This advancement ensures the spark plug fires earlier, maximizing combustion efficiency, resulting in higher RPMs and a noticeable increase in horsepower and throttle response.. Features a rare earth neodymium magnet. Each flywheel is precision balanced to reduce vibration and withstand the stresses of high-performance applications.. Flywheel weight 3.33lbs..

Adheres to component surfaces to prevent scuffing and galling during initial start-up. High quality formulation meets OEM performance specs for engine assembly lubricants. Proper lubrication of metal mating surfaces is essential prior to starting a new or rebuilt engine. Suggested Applications Engine bearings, camshafts, lifters, valves, guides and rocker shaft assemblies.

FitmentFor Predator 212cc Hemi engines, ensuring fit and reliable performance.Not compatible with Non-Hemi versions,please verify your engine model before purchasing.. Enhanced performance The flywheel has a built-in timing advance function that allows the ignition timing to reach the top dead center of 34 degrees, generating stronger and longer sparks to improve fuel combustion efficiency and help the engine unleash greater potential.. Boost Acceleration Our low drag fin design reduces air resistance while maintaining good cooling performance.Free up hidden power across the entire curve, achieve smoother high-RPM performance up to 10,000RPM,and enjoy faster acceleration and smoother operation.. Sturdy And DurableThe flywheel is made of high-quality material,heavy-duty,heat and wear resistance,sturdy and lightweight,ensuring the most outstanding engine.. Weighing only 3.3 lbs, it significantly reduces rotational inertia..

FitmentFor Honda gx200 For Clone 196cc BSP Tilly For Ghost For Predator 160cc 196cc 212cc 224cc 69730 69736 Non Hemi.. Package Includes1 x aluminum flywheel,1 x spark plug,1 x 22lb Springs Kit.. Die-cast aluminum, single molding, flaw-free.Integrated fan blades for easy installation.Multiple blades enhance heat dissipation.Equipped with puller hole for use with a puller.Features dynamic balance holes and has undergone dynamic balancing treatment.. High quality aluminum flywheel, reduced resistance, higher speed, increased power.The thread design plays a better fixing role, provides high-speed rotation, smooth operation.The flywheel features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC.. The spring and spark plug provide more power.These springs will provide extra performance at over 7000RPM. Length and Rate Tolerance will vary from spring to spring..

Fitment For Predator 212cc Hemionly fit the hemi predator engine.. Package Includes1 x aluminum flywheel,1 x Main Jet Kit,1 x 26lb Springs Kit1 x spark plug.. High quality aluminum flywheel, reduced resistance, higher speed, increased power.These springs will provide extra performance at over 10000RPM.Length and Rate Tolerance will vary from spring to spring.. Product performance upgrade, can withstand greater pressure, in the case of maintaining high speed, can also be a good control of the valve, and reduce wear, effectively reduce the fault situation.. The flywheel is made of a stronger aluminum material, the thread design plays a better fixing role, provides high-speed rotation, smooth operation, and the spring and Main Jet provide more power..

FitmentFor Predator 196cc, 212cc NonHemi Cast ,For Honda GX200. Premium Billet Construction Crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Black Finish Sleek and stylish, complementing your vehicle's interior.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Timing is 32 degrees with stock key..

FitmentFor Predator 196cc, 212cc NonHemi Cast ,For Honda GX200. Premium Billet Construction Crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Golden Finish Sleek and stylish, complementing your vehicle's interior.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Timing is 32 degrees with stock key..

FitmentFor Predator 196cc 212cc NonHemi Cast For Honda GX160 GX200 engineFor Coleman CT100U CT200U CT200U-EX BT200X. Timing AdvanceEngineered to advance ignition timing to approximately 32 degrees Before Top Dead Center, this billet aluminum flywheel unlocks significant power gains in your engine. The optimized timing ensures a more complete combustion cycle, resulting in increased horsepower, quicker throttle response, and improved overall engine performance.. Premium ConstructionMachined from high-grade billet aluminum,the flywheel offers superior strength and durability.The lightweight design reduces rotating mass, allowing the engine to rev faster and more freely.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Sleek Red FinishFinished in a durable red coating that resists corrosion and looks great in any engine bay..

FitmentFor Predator 196cc 212cc NonHemi Cast For Honda GX160 GX200 engineFor Coleman CT100U CT200U CT200U-EX BT200X. Timing AdvanceEngineered to advance ignition timing to approximately 32 degrees Before Top Dead Center, this billet aluminum flywheel unlocks significant power gains in your engine. The optimized timing ensures a more complete combustion cycle, resulting in increased horsepower, quicker throttle response, and improved overall engine performance.. Premium ConstructionMachined from high-grade billet aluminum,the flywheel offers superior strength and durability.The lightweight design reduces rotating mass, allowing the engine to rev faster and more freely.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Sleek Silver FinishFinished in a durable silver coating that resists corrosion and looks great in any engine bay..

FitmentFor Predator 212cc Hemi Only. Premium Billet Construction Crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Red Finish Sleek and stylish, complementing your vehicle's interior.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Timing is 32 degrees with stock key..

FitmentFor Predator 212cc Hemi Only. Premium Billet Construction Crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Silver Finish Sleek and stylish, complementing your vehicle's interior.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Timing is 32 degrees with stock key..

Fitment This flywheel is engineered with a platform universal design, fit both - variants. It adopts standardized crank taper and clutch mounting interface for direct fitment without modification.. Wide Compatibility This Aluminum Flywheel Fits Predator 212cc196cc224cc 69730 69736 GX160 GX200 196cc BSP Tilly Clone engine. Perfect for Coleman CT200U CT200U-EX BT200X, Axi M200,MassimoBaja Warrior MB165 MB200 ,KT196 Go kart and other vehicles powered by the engine above.. Boost Acceleration Our flywheel for predator 212cc could enhance your mini bike or go karts engine performance. Just replacing our 10krpm 212 flywheel non hemi, The motor can reach to excellent speed of 10,000 rpm making engine achieve faster acceleration. Durable Wear-resistant The flywheel is Crafted from high-strength heat-resistant cast aluminumlighter and stronger than stock iron or plastic flywheels. Features reinforced threaded holes in the hub to protect the taper and secure the keyway, ensuring durability and reliability.. Surface Imperfections there are no crank on the surface of flywheel.The flywheel is engineered to stabilize mechanical power and ensure smooth operation. Package includes 1 aluminum flywheel and 1 metal crankshaft key..

Precision-Fit Billet Rod Forged aluminum connecting rod 3.308 w bearings designed exclusively for Predator 212cc HemiNon-Hemi engines.NOT fits Honda GX200, Clone 196cc, Predator Ghost 212, or 224 cranks.. Lightweight Speed Boost High-compression Flat-Top Piston reduces rotating mass, while the lightweight wrist pin and thin ring pack maximize RPM and power output for racing dominance.. Pro-Grade Durability .010 Head Gasket Ultra-thin yet rugged gasket ensures optimal sealing and combustion efficiency for your 212cc Predator engine, boosting performance without leaks.. Race-Ready Valve Train High-tensile steel 26lb Valve Springs deliver flawless valve control at high RPM, preventing float and ensuring precise timing for competitive racing.. Billet Aluminum Retainers CNC-machined, hard-anodized retainers offer lightweight strength and vibrant style while securing valves under extreme speeds.. ? Oil-Only Lubrication For best results, avoid sticky assembly lubesuse your engines planned oil to coat internal parts during installation.. Package Includes 1Connecting Rod kit 3.308 1Aluminum Flywheel, 226lb Valve Spring,1Piston Set, 2valve keeperslocks,1Gasket Set.

For the electric start Honda GX200Clone Clone 196cc, Ducar 196212 and Tillotson 196225228236, WildCat 223, Predator Ghost 212 and Predator 224cc NON Hemi engines flywheel.. Manufactured from 7075 aluminum.. Replaceable 7075 aluminum ring gear. Also works with the OEM pull start. Instantly add electric start capability to your Honda GX200 or Predator 212 engine. Perfect for hassle-free starting.. Precision-cut teeth ensure reliable and smooth meshing with your electric starter motor for dependable performance every time..

For Predator 212 196cc 224cc Non Heminot for hemi engine, GX160 GX200, 6.5hp OHV Clone small engine.. For Coleman CT200U BT200X CT200U-ex B200R RB200, MassimoBaja MB165 MB200 Warrior, Heat, Mini Baja, Realtree RT200 Mini Bike For Coleman KT196 Go Kart. Package Include 1 Aluminum Flywheel 1 Racing Shaft Rocker Arm Set w Black 1 Clear Valve Cover with Gaskets 1 36lb Valve Springs. The one piece flywheel is made of quality cast aluminum material, heavy-duty, heat and wear resistance, sturdy and lightweight. 212 predator flywheel adopts a low drag precise design, with smooth and nice machining, achieving your mini bike or go kart a better acceleration. The excellent motor speed of up to 10000 rpm allows your vehicles to rev quicker and more powerful..

FitmentBillet Aluminum Flywheel 3.308 Billet Rod .265 Camshaft for Predator 212cc Hemi versions engine go kart cart.. Will Not fit the Honda Gx200, Clone 196cc, Predator Ghost 212 and Predator 224 cranks. Premium Billet Construction Speedway Billet Aluminum Flywheel crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Enhanced Engine Performance The .265 Camshaft significantly boosts power, torque, and acceleration for 212cc Hemi Predator engines. Its high lift and duration design improves throttle response and delivers a more aggressive exhaust note. High Compression Performance Flat Top Piston w Thin Ring pack,Lite Weight Wrist pin with locks light weight reduces rotating mass and increases RPM and Power.Side Cover gasket and .010 High Compression Head Gasket. Kit Includes Short Fin Billet Flywheel1, 3.308 Billet Connecting Rod1, .265 Camshaft 1, .550 Piston Kit1, 22lb valve springs 2, Side Cover Gasket1, Spark Plug1,.

FitmentFor Predator 196cc 212cc NON Hemi,224cc ghost 208cc 69730 69736 Honda GX160 GX200 196cc BSP Tilly Clone engine.For Coleman CT200U BT200X CT200U-EX, Baja Warrior MB200 MB165, Massimo MB200 MB165 mini bike and KT196 go kart. Good ConstructionMachined from high-grade billet aluminum,the flywheel offers superior strength and durability.The lightweight design reduces rotating mass, allowing the engine to rev faster and more freely.. Excellent Heat DissipationEquipped with 12 fan blades to actively deliver airflow to the cylinder head and cylinder.It effectively reduces power heat fade and prevents engine knock during long-duration high-rev operation, ideal for go-karts and mini bikes on race tracks.. High-RPM StabilityUniformly arranged blades enable high-precision dynamic balance via CNC machining. It runs with minimal vibration at high RPM, protecting crankshafts and bearings for long-term reliable use.. Adjustable TimingFeaturing an adjustable range from 24 to 38, this component fully accommodates stock engines as well as modified setups with high compression ratios, aggressive camshafts and extended stroke kits. It works seamlessly with various upgraded configurations without requiring a flywheel replacement, delivering exceptional performance and cost-effectiveness..

FitmentFor Predator 212cc Hemi Only. Good ConstructionMachined from high-grade billet aluminum,the flywheel offers superior strength and durability.The lightweight design reduces rotating mass, allowing the engine to rev faster and more freely.. Excellent Heat DissipationEquipped with 12 fan blades to actively deliver airflow to the cylinder head and cylinder.It effectively reduces power heat fade and prevents engine knock during long-duration high-rev operation, ideal for go-karts and mini bikes on race tracks.. High-RPM StabilityUniformly arranged blades enable high-precision dynamic balance via CNC machining. It runs with minimal vibration at high RPM, protecting crankshafts and bearings for long-term reliable use.. Adjustable TimingFeaturing an adjustable range from 24 to 38, this component fully accommodates stock engines as well as modified setups with high compression ratios, aggressive camshafts and extended stroke kits. It works seamlessly with various upgraded configurations without requiring a flywheel replacement, delivering exceptional performance and cost-effectiveness..

Billet Aluminum Flywheel For Predator 79cc98cc motors. Predator 79cc Billet Flywheel. manufactured from aluminum. Utilizes powerful rare earth magnets.. Predator 79cc Billet Flywheel. Timed at 28 degrees BTDC4 degrees advance. The flywheels use stronger magnets and timing advance to provide the most efficient and effective ignition process that the motor can produce.. They are designed with less drag and balanced to produce as much free spin possible. The rotational force increases with the motors rpm and helps to maintain momentum throughout the entire process..

3 Diameter,10 Length,0.31 Gallon Approx. MaterialAluminum. 18 center outlet,Vented Cap. Recommended Items316 Fuel Line,Gas Tank Bands,Shut-Off Valve.

FitmentFor Predator 212cc Hemi Only. Premium Billet Construction Crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Golden Finish Sleek and stylish,complementing your vehicle's interior.. Unique DesignAll billet aluminum flywheel with unique fin design for low wind resistance resulting in greater horse power compared to the traditional fin design.. Timing is 32 degrees with stock key..

STRICT COMPATIBILITY - NON-HEMI ONLY Custom engineered for Non-Hemi fits Predator 212cc, 196cc, 224cc, and for Harbor Freight 6973069736 small engines. Perfectly fits Coleman CT200U, BT200X, CT200U-EX mini bikes, and fits KT196 go-karts. IMPORTANT NOTE Will NOT fit Predator Hemi engines or Hemi Ghost models. Always verify your engine type before purchasing to avoid return hassles.. 10,000 RPM HIGH-SPEED STABILITY POWER Rated for safe operation up to 10,000 RPM. Super lightweight cast aluminum design significantly reduces rotating mass compared to stock iron flywheels. Revs quicker, accelerates faster, and unlocks more horsepower throughout your racing engine's entire power curve.. OPTIMIZED 24-DEGREE TIMING ADVANCE Precision-machined with a 24-degree timing advance to completely optimize your engine's ignition sequence. This exact timing specification delivers a highly concentrated and efficient spark, maximizing fuel combustion and providing an aggressive, responsive throttle feel that stock flywheels cannot match.. ANTI-DAMAGE TAPER CORROSION PROTECTION Upgraded center hub features reinforced threaded puller holes to ensure easy, damage-free removal during maintenance. Precision-cut keyway ensures a rock-solid lock on the crankshaft taper, eliminating shaft slippage and preventing catastrophic key shear at high speeds.. Package Including 1 x aluminum flywheel, 1 x flywheel crankshaft key.

The Universal 35 Chain 53T Split Sprocket With Adapter fits many different mini bikes,motorcycle and go karts. Compatible with Predator 212cc 196cc 79cc Mini Bike Go Kart. For Colemann CT200U-EX CT200U BT200X CT100U CC100X MegaMota B212 Mini Bike. Easy to Install The split sprocket is made of quality aluminum alloy material, the black sprocket hub adapter is forged with quality aluminum. Package Included 1 x red split sprocket, 1 x black sprocket hub adapter, 6 x screws, 6 x nuts..

Precision FitDesigned Exclusively for Predator 212cc196cc Hemi Engines. Will NOT fit Honda GX200, Clone 196cc, Predator Ghost 212, or Predator 224 crankshafts. Verify your engine model before purchase.. High-Strength Billet RodBuilt for Performance CNC-machined forged aluminum connecting rod with premium bearings for extreme durability. Handles higher RPM and torque than stock rods. Installation Tip Align bearing tangs with rod cutouts for a secure fit.. 26lb Valve SpringsOptimized for High RPM Made from high-quality steel for consistent spring force, smooth rebound, and reliable valve control. Ensures precise intakeexhaust valve timing, ideal for racing and performance upgrades.. Billet Aluminum RetainersLightweight Tough Precision CNC-machined from hard-anodized aluminum for superior strength and wear resistance. Vibrant colors add a custom look while keeping valves secure at high speeds.. Pro Installation TipCleanliness is Critical Before assembly, clean bearing and rod serrations thoroughly to ensure proper seating. Correct alignment prevents failures and maximizes engine performance.. Package Includes1Connecting Rod3.308 1HEMI Aluminum Flywheel,126lb Valve Spring,2valve keeperslocks,1Gasket Set.

3 Diameter,10 Length,0.31 Gallon Approx. MaterialAluminum. 18 center outlet,Vented Cap. Recommended Items316 Fuel Line,Gas Tank Bands,Shut-Off Valve.

Fitment For Predator 212cc NON Hemi, 224cc New Ghost 212cc engine.Replace For Honda GX200, Clone 196cc BSP Tilly.For Coleman Mini Bike CT200U BT200X CT200U-EX GX160 GX200 6.5HP Minibike. High-Performance Upgrade Unlock your engine's true potential This precision-balanced aluminum flywheel is designed for high-revving up to 10,000 RPM, paired with a performance speed coil for faster, more reliable spark at high speeds,steel center hub sturdy and durable to prevent damage to taper, fixed keyway, center hub also has threaded holes for flywheel puller use, with longer service life. Superior Material Crafted from high-grade aluminum alloy,allowing for quicker engine acceleration and reduced stress on the crankshaft. The included performance coil made of high-quality metal and insulating rubber, providing stronger durability and reliability,ensures a strong and consistent spark.. Enhanced Engine Efficiency The lightweight flywheel reduces rotational mass, leading to snappier throttle response and improved overall engine performance. Package Include1Aluminum Flywheel,1 Speed Coil.. Remindwill not fit the hemi predator engine.

FitmentFor Predator 212cc Non-Hemi Engine Go Kart Cart.. Package IncludesA Connecting Rod,18lb Valve Spring,Flywheel,Gasket kit,Piston Kit,Magnetic Oil Drain Sump Plug Kit.. When tightening the connecting rod's bolts, don't tighten them all at once. Rod bolt torque 170 Inchlbs. Use an inch pound torque wrench with a 14 12 point socket.. Die-cast aluminum, single molding, flaw-free.Integrated fan blades for easy installation.Multiple blades enhance heat dissipation.Equipped with puller hole for use with a puller.Features dynamic balance holes and has undergone dynamic balancing treatment.High quality aluminum flywheel, reduced resistance, higher speed, increased power. The thread design plays a better fixing role, provides high-speed rotation, smooth operation. The flywheel features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC.. The spring provide more power. These springs will provide extra performance at over 7000RPM.Length and Rate Tolerance will vary from spring to spring..

Wide CompatibilityThis timing key works with most 196cc224cc small engines, including fit for Predator 212cc Hemi non-Hemi, for Honda GX160GX200 and clone versions, for Tillotson, for Ghost 212cc, and more.. Wide CompatibilityFit for Coleman CT200UBT200XCT200U-EX, for Baja Warrior MB165MB200, for Trailmaster 200X, for Coleman KT196 go kart, and many yard equipment such as generators, pressure washers, log splitters, tillers, etc. Always verify your engine model before purchase.. Precise Ignition Timing Adjustment 8 flywheel timing key allows you to advance or retard ignition timing by 8 degrees. This simple yet effective replacement part helps fine-tune your engines combustion cycle for better throttle response, low-end torque, or top-end power depending on your fuel type and setup.. Durable Construction Precise DimensionsThe timing key is made of corrosion-resistant and heat-resistant steel to withstand high-rpm and high-temperature operation. Built to last through repeated tuning and engine stress..

FitmentBillet Aluminum Flywheel 3.308 Billet Rod .265 Camshaft for Predator 212cc Non-Hemi versions engine go kart cart.. Will Not fit the Honda Gx200, Clone 196cc, Predator Ghost 212 and Predator 224 cranks. Premium Billet Construction Speedway Billet Aluminum Flywheel crafted from high-quality aluminum for durability and reduced weight.Features a rare earth neodymium magnet. Each flywheel is spun balanced.. Enhanced Engine Performance The .265 Camshaft significantly boosts power, torque, and acceleration for 212cc Non-Hemi Predator engines. Its high lift and duration design improves throttle response and delivers a more aggressive exhaust note. Kit Includes Short Fin Billet Flywheel1, 3.308 Billet Connecting Rod1, .265 Camshaft 1, .550 Aluminum Piston Kit1, 22lb valve springs 2, Side Cover Gasket1, Spark Plug1,.

High Compatibility High-performance billet aluminum flywheel for Predator 212cc Non-Hemi engines. Perfectly fit Honda GX160 GX200 engines and various fit Coleman CT200U, BT200X mini bikes and go karts.. Aluminum die casting This flywheel is processed by high-strength aluminum die casting,this flywheel is significantly lighter than stock cast iron ones. It reduces rotating mass for faster throttle response and improved acceleration.. Enhanced Heat Dissipation Surface sandblasting process enhances contact area, fan blade structure accelerates air circulation to maintain optimal engine temperature during high-rpm operation. A must-have for Predator 212 performance part upgrades and racing applications.. Reliable Ignition Magneto Features a high-quality magnet for consistent spark and ignition timing. This upgrade ensures your fit 196cc or 212cc 224cc engine runs smoother and more efficiently at higher speeds.. Easy Installation Reserved removal holes, you can quickly pull out the flywheel directly with the flywheel removal tool.. Perfect after-sales servicewe have a professional team and customer service team. If any problems arise, we are willing to provide technical assistance at any time and provide perfect after-sales service..

Fitment 10krpm flywheel For Predator Harbor Freight 212cc HEMI ONLY. Remindwill fit the Predator 212 Hemi engine. FunctionHelps your motor to rev quicker while still moving enough air for cooling. MaterialCNC Machined Aluminum ally Flywheel. Package Include1Aluminum Flywheel.

FITMENTCompatible with Predator 212, Coleman CT200U B200R 200cc Mini Bike, KT196 Go Kart, Honda 6.5HP GX160 and 196 Hisun Engine. ADVANTAGEThe upgraded crank-handle starting design eliminates the sudden jerking, bouncing, and instability typical of traditional pull-cord starters, ensuring smoother engine starts while reducing physical strain. EXCELLENT QUALITYThis starter is made of tough, durable materials that resist wear and high temperatures. It can handle long-term use without frequent replacement, ensuring reliable performance over time. EASY INSTALLATIONNo special tools or skills needed simply attach the starter to the original steel blower housing using just 3 bolts 6 included for backup or reinforced installation. The entire process is quick, hassle-free, and more secure with extra fasteners provided. GUARANTEEAll products are sold after strict inspection with 12 months guarantee. If you are not satisfied with your purchase for any reason, contact us.

Performance flywheel parts for off-road mini bike or go kart upgrade. Lighter and Stronger than stock ones. OEM quality, can bear up to 10k rpm in less than 3 minutes.. Flywheel for Predator 212 224 cc 69730 NonHemi, made of aluminum casted.. Not for hemi predator engines.. Please check the size and product images carefully before ordering.. A cast aluminum flywheel wrapped in a foam bag weighs about 3.38 pounds in a box..

12 Tooth Centrifugal ClutchGo Kart Clutch 34 Bore 12T for 35 Chain, Perfect for Go Kart, Minibike and Fun Kart Engine 34 BARChain Not included. Compatible Centrifugal Clutch Fits Honda GX160, GX200, GX 140, GX120, GC160, GC190, Harbor Freight Greyhound 196cc, Harbor Freight Predator 212cc, Briggs and Stratton Tecumseh Engines 2-6.5 HP with 34 shaft. Applicable ModelsThe 34 centrifugal clutch is suitable for Any Other Engines with 34 Crank Shaft and 316 Keyway, Most 5.5 HP Clones, 6.5 HP Clones and 4-7HP Motors in All Brands. High Quality Material Go kart clutch is made of quality iron material, which is and maximum torque, wear-resisting and fast heat dissipation. Bolt,Washer,Screws and Allen Wrench are All Included. Note Please check the TYPE before purchasing. Package Includes 1 x 34 Bore 12 Tooth Clutch, 2 x Clutch Bolt2 x Washer Kit, and 2 x Screw wrench. You can get the most friendly customer service.

Fit for Predator 212cc 196cc 224cc 69730 69736 Non Hemi Ghostnot for hemi engine, Hond GX160 GX200 6.5hp clone engine,Tillotson 212cc, Harbor Freight,Coleman Mini Bike CT200U CT200U-EX BT200X, Axi M200,MassimoBaja Warrior MB165 MB200 ,KT196 Go kart and other vehicles powered by the engine above 2.Runs Cooler, Never Fades -the aluminum flywheel dissipates heat fast, preventing power-robbing heat soak during hard runs.. Runs Cooler, Never Fades -the aluminum flywheel dissipates heat fast, preventing power-robbing heat soak during hard runs.. The carburetor jets 3536 Main Jet, 45 Pilot Jet deliver the precise extra fuel needed to complement the increased airflow from the lightweight flywheel, maximizing horsepower and torque gains.. Conquer High RPMs - Upgraded valve springs prevent float, unlocking full power potential from your lightweight flywheel's acceleration.. Our flywheel is precision die-cast from high-strength aluminum, ensuring uniform density and reliable performance in every unit..

FITMENT For Predator 212cc 224cc ghost 208cc 69730 69736 GX160 GX200 196cc BSP Tilly Clone engine. Not Fit For Predator Hemi Engine. For Coleman CT200U BT200X CT200U-EX, For Baja Warrior MB200 MB165, For Massimo MB200 MB165 mini bike and KT196 go kart. PREMIUM FORGED ALUMINUM CONSTRUCTION Crafted from high-grade forged aluminum under strict quality control, this part offers superior strength and durability while being lightweight. It withstands intense stress and impact, ensuring long-lasting performance and reliability for your mini bike or go-kart.. ENHANCED ACCELERATION POWER Our low-resistance precision design and ultra-smooth surface minimize friction and drag. This translates directly to sharper throttle response, quicker acceleration, and increased overall power output, giving your vehicle an instant boost in speed.. BUILT-IN COOLING FOR PEAK PERFORMANCE The specialized heat dissipation structure effectively prevents overheating by drawing heat away from the engine during high-speed runs or prolonged use. This maintains stable engine power and protects critical components, allowing for consistent performance under heavy loads.. PACKAGE INCLUDE 1 x aluminum flywheel.

Higher Top Speed - The aluminum alloy flywheel for 212 Non hemi engine reduced rotating mass lets your engine spin up easier and reach higher RPMs.. Make your CT200U BT200X Mini Bike cool better and run more smoothly - Aluminum dissipates heat far better than iron, preventing power loss.. Precision Machined - Perfectly balanced from billet aluminum with a durable anodized finish.. Prevent Valve FloatOur matched valve springs work in unison with the lightweight flywheel, ensuring valve precision at high RPM to eliminate power loss and fully unleash your engine's designed horsepower.. Professionally balanced to eliminate vibrations, ensuring buttery-smooth operation and optimized performance at all RPMs.. Features integrated puller threads for quick, safe, and damage-free removalsaving time and hassle during installation or upgrades.. NOTE Not Fit Hemi engine,Please verify that the product is compatible before purchasing..

FitmentFor Predator 212cc Non-Hemi Engine Go Kart Cart.. Package IncludesA Connecting Rod, Valve Spring,Flywheel,Gasket kit,Piston Kit,Magnetic Oil Drain Sump Plug Kit.. When tightening the connecting rod's bolts, don't tighten them all at once. Rod bolt torque 170 Inchlbs. Use an inch pound torque wrench with a 14 12 point socket.. Die-cast aluminum, single molding, flaw-free.Integrated fan blades for easy installation.Multiple blades enhance heat dissipation.Equipped with puller hole for use with a puller.Features dynamic balance holes and has undergone dynamic balancing treatment.High quality aluminum flywheel, reduced resistance, higher speed, increased power. The thread design plays a better fixing role, provides high-speed rotation, smooth operation. The flywheel features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC.. The spring provide more power. These springs will provide extra performance at over 7000RPM.Length and Rate Tolerance will vary from spring to spring..

FitmentFor Predator 212cc Only Hemi Engine Go Kart Cart.. Package IncludesA Connecting Rod,18lb Valve Spring,Flywheel,Gasket kit,Piston Kit,Magnetic Oil Drain Sump Plug Kit.. When tightening the bolts, don't tighten them all at once. Tighten them in three stages to avoid stripping.Rod bolt torque 170 Inchlbs.. These springs will provide extra performance at over 7000RPM. Length and Rate Tolerance will vary from spring to spring.. The flywheel is made of a stronger aluminum material,reduced resistance, higher speed, increased power, can withstand greater pressure, in the case of maintaining high speed, can also be a good control of the valve, and reduce wear, effectively reduce the fault situationthe thread design plays a better fixing role..

FitmentFor Predator 212cc Only Hemi Engine Go Kart Cart.. Package IncludesA Connecting Rod,18lb Valve Spring,Flywheel,Gasket kit,Magnetic Oil Drain Sump Plug Kit.. When tightening the bolts, don't tighten them all at once. Tighten them in three stages to avoid stripping.Rod bolt torque 170 Inchlbs.. These springs will provide extra performance at over 7000RPM. Length and Rate Tolerance will vary from spring to spring.. The flywheel is made of a stronger aluminum material,reduced resistance, higher speed, increased power, can withstand greater pressure, in the case of maintaining high speed, can also be a good control of the valve, and reduce wear, effectively reduce the fault situationthe thread design plays a better fixing role..

Precision FitDesigned Exclusively for Predator 212cc196cc Hemi Engines. Will NOT fit Honda GX200, Clone 196cc, Predator Ghost 212, or Predator 224 crankshafts. Verify your engine model before purchase.. High-Strength Billet RodBuilt for Performance CNC-machined forged aluminum connecting rod with premium bearings for extreme durability. Handles higher RPM and torque than stock rods. Installation Tip Align bearing tangs with rod cutouts for a secure fit.. 26lb Valve SpringsOptimized for High RPM Made from high-quality steel for consistent spring force, smooth rebound, and reliable valve control. Ensures precise intakeexhaust valve timing, ideal for racing and performance upgrades.. High-Compression Flat Top PistonBoost Power RPM Performance Lite weight 70mm Flat Top PistonThis lite weight wristpin increase RPM and reduces rotating mass. Billet Aluminum RetainersLightweight Tough Precision CNC-machined from hard-anodized aluminum for superior strength and wear resistance. Vibrant colors add a custom look while keeping valves secure at high speeds.. Package Includes1Connecting Rod3.308 1Aluminum Flywheel, 226lb Valve Spring,1Piston Set, 2valve keeperslocks,1Gasket Set,.

Upgrade Flywheel for Predator 212 224cc 69730,fit for non-hemi engines, not fit for hemi engines.. Flywheel Functional coatingHigh emissivity coatings can more effectively emit surface heat into the surrounding environment in the form of infrared radiation. The design structure of the flywheel can bring a larger contact area, promote air flow in small spaces, and quickly take away heat.. Better quality materials are lighter in weight, good durability, and the coating is resistant to high temperature, rust, and oxidation. Performance flywheel for off-road mini bike or go kart upgrade. Lighter and Stronger than stock ones..

Fitment 212cc hemi flywheel fits for Predator 212cc 60363 only Hemi engine, fits for Hond GX160 GX200 engine. Compatible with Coleman mini bike CT200U CT200U-EX BT200X, Baja Warrior MB165 MB200, KT196 Manc, Yerf Do go kart, lawn mower, generator and other vehicles which are equipped with the engine above. High Efficency The flywheel for hemi 212 can reach to excellent speed of 10,000 rpm, spin at higher RPM. Allowing your vehicles with excellent power by rev lot smoother and better acceleration. The cooling fins are taller creating more airflow to cool motor better than stock. Every drop of fuel is fully utilized to obtain more energy, increase the output of engine. This flywheel features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC. Strong Strength and Excellent Durability The upgrade aluminum flywheel for 212cc predator hemi engine is made of good quality aluminum material, with strong strength to ensure normal work condition. Our 212cc hemi flywheel has long service time. Improving More Power Horse Parts 2 x 26lb valve springs made from high-quality raw materials, The spring force is uniform, the rebound is stable, the elasticity is good. It could regularly open and close the intake and exhaust valves. which increases more power horse. The carburetor main jet kit could control the flow of fuel, giving an appropriate amount of fuel supply based on the engine's speed and load. Easy To Install The 212cc hemi flywheel is easy to install. Please lap the flywheel to your crank. Tip Cracks for predator 212 flywheel hemi like hairline is normal due to the integrated casting process. Don't worry. It won't affect the performance of the flywheel. Package Iist 1 x aluminum 212cc hemi engine flywheel, 2 x 26lb valve springs, 1 x main jet kit1 x emulsion tube, 3 x main jet , 1 x metal flywheel crankshaft key, 1 x spark plug.

Made in USA. SFI certified. 32 degrees timing with stock key. Minimum coil gap .030. 3.4 lbs. Torque to 65 ftlbs. will not work with charging stator.

Fits the 212cc Harbor Freight Predator Hemi with the cast aluminum valve cover.. Will work with stock pull rope and OEM coil.. Minimum coil gap of .030. Flywheel is set to 32 degrees BTDC with a stock key. Weight 3.4lbs.

Fitment Flywheel remove tool is for most flywheels with steel adjustable timing hubs, PVL clone flywheel and raceseng flywheel with puller hole. Applicable Engine This crankshaft hold and flywheel remove tool is a perfect tool for flywheel installation and disassembly. For Predator 6.5hp 212cc OHV horizontal shaft gas engine not for hemi engine, GX160 GX200 6.5hp clone engine, 212cc, for Harbor Freight. Note Crankshaft holder tool is for most engines with 34 crankshaft, not for other size, and make sure your flywheel has puller hole to use this flywheel puller. Flywheel Installation and Removal Tool This tool slides over any 34 keyed crank and allows the flywheel to be torqued properly. It makes install the flywheel easier and saves time. Compared with hitting the crankshaft with a hammer, using this tool to remove the flywheel is more convenient, labor-saving and avoiding damage to the crankshaft and flywheel. Installation Notices 1. Install the threaded screw into clean and lubricated puller holes, be sure to thread the screws in fully. 2. Tighten the nuts evenly back and forth in 12 turn increments until the flywheel pulls off. 3. Stubborn flywheels may require that you hit the center of the puller block with a hammer once significant pressure is applied by tightening the nuts. Be careful not to strike the threaded rods and never hit the flywheel itself with a hammer.

Fitment For Predator 212cc NON Hemi, 224cc New Ghost 212cc engine. Replace For Honda GX200, Clone 196cc BSP Tilly. Package Include1Aluminum Flywheel. Remindwill not fit the hemi predator engine.

Fitment Fit for Predator 212cc 196cc 224cc Non Hemi Ghostnot for hemi engine, Hond GX160 GX200 6.5hp clone engine,Tillotson 212cc, Harbor Freight,Coleman Mini Bike CT200U CT200U-EX BT200X, Axi M200,MassimoBaja Warrior MB165 MB200 ,KT196 Go kart and other vehicles powered by the engine above. Solving The Power Problem The 212cc flywheel features an ultra-low drag fine design that will greatly reduce air drag on your racing engine while still moving enough air for cooling. Less air drag on the flywheel means more power freed up throughout the power curve especially on an excellent speed up to 10,000rpm, make your engine work like a charm with faster and smoother running, better acceleration.The included valve springs and main jets can give you more options to increase power. High Strength Heat Resistant Our predator 212 flywheel is made of high quality cast aluminum instead of the original iron and plastic material, strong and lightweight to ensure the great performance. In addition, the center hub is equipped with strong and durable thread holes, which can keep the taper from getting damaged and fix the keyway.This flywheel features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC. Package Including 1 x aluminum flywheel, 2 x 26lb valve springs, 1 x main jet kit1 x emulsion tube,3 x main jet .036 .037 .038 1 x metal flywheel crankshaft key. Note You may find there are some cranks on the surface of flywheel when you open the package. Dont worry, this is due to integrated casting during the producing process and its also possible to balance the engine so that it continues to have good performances. Mechanical power is the energy created when the engine is running. The flywheel works to balance the mechanical power by storing it.But it wont the normal use. Besides, it does not fit the Predator 212 Hemi.

Engine Compatibility 8 flywheel timing key and carburetor jet kit compatible with Predator 212cc, 196cc, and 224cc engines, including models 60363, 68121, 68120, 69727, and 69730, both hemi and non-hemi versions. Also compatible with Honda GX160 GX200 6.5HP and 7HP clone engines, Tillotson 196cc 212cc 225cc 236cc 268cc, and Ghost 212 engines. Wide Application Suitable for many mini bikes, go karts, and outdoor equipment powered by the engines listed above. Compatible with Coleman CT200U, BT200X, CT200U-EX, CT200U-Trail, CT200U-A, CT200U-EXR, RB200, B200R, TrailMaster 200X and MB200-2, Baja MB165 MB200, Hammerhead 80T Mini Shark, Coleman KT196 BK200, Massimo MB200, and other vehicles equipped with compatible engines. Offset Timing Key Design The included 8 flywheel offset timing key is designed to position the flywheel with an approximately 8-degree timing offset, supporting proper ignition timing alignment when replacing worn or damaged timing keys. Precision Carburetor Jet Set Includes three carburetor main jets .036, .037, .038 and one emulsion tube. These components allow adjustment of fuel delivery to match different operating conditions or engine setups. Durable Metal Construction Manufactured from corrosion-resistant metal materials with precise machining for accurate fitment. Smooth jet surfaces and consistent dimensions help support stable fuel flow and reliable engine operation.

Upgrade Flywheel for Predator 212 224cc 69730,fit for non-hemi engines, not fit for hemi engines.. Flywheel Functional coatingHigh emissivity coatings can more effectively emit surface heat into the surrounding environment in the form of infrared radiation. The design structure of the flywheel can bring a larger contact area, promote air flow in small spaces, and quickly take away heat.. Better quality materials are lighter in weight, good durability, and the coating is resistant to high temperature, rust, and oxidation. Performance flywheel for off-road mini bike or go kart upgrade. Lighter and Stronger than stock ones..

Precision-Fit Billet Rod Forged aluminum connecting rod 3.308 w bearings designed exclusively for Predator 212cc Non-Hemi engines.NOT fits Honda GX200, Clone 196cc, Predator Ghost 212, or 224 cranks.. Lightweight Speed Boost High-compression 70mm Ceramic Coated Flat-Top Piston reduces rotating mass, while the lightweight wrist pin and thin ring pack maximize RPM and power output for racing dominance.. Pro-Grade Durability .010 Head Gasket Ultra-thin yet rugged gasket ensures optimal sealing and combustion efficiency for your 212cc Predator engine, boosting performance without leaks.. Race-Ready Valve Train High-tensile steel 26lb Valve Springs deliver flawless valve control at high RPM, preventing float and ensuring precise timing for competitive racing.. Billet Aluminum Retainers CNC-machined, hard-anodized retainers offer lightweight strength and vibrant style while securing valves under extreme speeds.. ? Oil-Only Lubrication For best results, avoid sticky assembly lubesuse your engines planned oil to coat internal parts during installation.. Package Includes 1Connecting Rod kit 3.308 1Aluminum Flywheel, 226lb Valve Spring,1Piston Set, 2valve keeperslocks,1Gasket Set.

Made in USA. SFI certified. Torque to 65 ftlbs. Minimum coil gap .030. 32 degrees timing with stock key. 3.4 lbs. will not work with charging stator.

Compatible with 212cc flywheel is compatible with Predator 212cc 224cc 60363 Only Hemi engine, GX160 GX200 6.5hp clone engine, Tillotson 212cc, Harbor Freight, Coleman Mini Bike CT200U CT200U-EX BT200X, Axi M200, Baja Warrior MB165 MB200, Manco Yerf Do Go kart, Lawn Mower and other vehicles powered by the engine above. Good Performance The 212 hemi flywheel is constructed of high-strength steel to withstand high RPMs and heavy loads. Its precision-balanced design reduces vibration, improves engine stability and maximises power output. Especially at very high speeds of up to 10,000rpm, your engine will run like a stream. Durable and Long-Lasting Construction This 212cc flywheel is made of high-quality materials to ensure long-lasting durability even under extreme conditions. It is a reliable choice for high performance engines. Package Includes 1 x aluminum hemi flywheel, 2 x 26lb valve springs, 1 x main jet kit1 x emulsion tube, 3 x main jet .036 .037 .038, 1 x metal flywheel crankshaft key. Note This flywheel does not apply to Non-Hemi predator engine and Predator 212 Hemi Ghost. Designed to match OEM specifications, this flywheel is easy to install without requiring additional modifications. Whether youre a DIY enthusiast or a professional mechanic, youll appreciate the hassle-free setup.

Fitment Aluminum flywheel fit for Predator 212 non hemi engine and Predator 224cc 5.5hp 6.5hp GX160 GX200 69730 69736 engine, Clone 196cc BSP Tilly Clone engine, Ghost 212cc engine, 212 Tillotson Hemi engine Not fit for Hemi Predator engine. Compatibility Aluminum flywheel fit Coleman CT200U BT200X CT200U-EX B200R mini bike, Massimo MB165 MB200 mini bike, Baja MB165 MB200 mini bike, KT196 go kart. Material The flywheel is made of cast aluminum and there probably will be casting marks but this does not affect the normal use of the product. The flywheel enhances the performance and spin up rpms of the engine, the rotational speed can reach 10,000 rpm and great alternative to the original non-hemi crankshaft installed on predator 212 hemi. Package Includes 1 x aluminum flywheel, 2 x valve springs 1 x spark plug, 1 x crankshaft flywheel key, 3 x main jet. NOTE Please be carefully check our pictures and product description and then compare your original goods before ordering, make sure it is what you need.

34 BORE, 12T FOR 35 CHAINThis centrifugal clutch features a 34 bore and 12-tooth sprocket for 35 chain, designed for compatible 26.5 HP small engines with approximately 2300 RPM engagement. DURABLE STEEL CONSTRUCTIONMade from durable steel to handle the friction and heat generated during clutch engagement, helping provide reliable performance for compatible go kart and minibike drive systems. FITS COMPATIBLE SMALL ENGINESDesigned for engines with a 34 shaft and 316 keyway, including Predator 212cc and compatible Honda GX120GX140GX160GX200 and GC160GC190 keyed-shaft versions. Please verify fit before ordering. GREAT FOR GO KART MINIBIKE SETUPSA practical replacement clutch for compatible go karts, minibikes, and fun kart applications using a 35 chain drive system. HARDWARE INCLUDED FOR INSTALLATIONIncludes 1 clutch, 1 clutch bolt and washer kit, 1 screw set size 14-28x58, and 1 Allen wrench for added convenience. Chain is NOT included.

Compatible Models Flywheel 10kRPM and coil fit for Predator 212cc NON Hemi, 224cc New Ghost 212cc engine, fit for Honda GX200, Clone 196cc BSP Tilly, not fit for hemi predator engine. High Quality Material SFI certified billet aluminum flywheel with tin plate metal valve cover, steel center hub sturdy and durable to prevent damage to taper, fixed keyway, center hub also has threaded holes for flywheel puller use, with longer service life. Ignition Coil Material Speed coil made of high-quality metal and insulating rubber, providing stronger durability and reliability, increasing ignition energy for quick start. Efficient Combustion Billet aluminum flywheel uses high-strength rare earth magnets, match the flywheel and spark plug to produce sparks with enough energy to improve the operating efficiency of the engine, better energy storage and discharge. Unique Design Special low drag fan design unique to the flywheel, helping your motor rotate faster and convenient for your use. 1 x aluminum flywheel,1 x speed coil. Easy to install, 100 quality tested before leaving the factory, stable performance, saving you time and money. If you have any questions, please feel free to contact our technical team.

FitmentFor Predator 212 ONLY Hemi Aluminum. High EfficencyThe Predator 212 Hemi flywheel can rotate at higher speeds. Better acceleration allows your vehicle to perform excellent power. The cooling fins are higher, creating better airflow than stock to cool the motor more.. Strong Strength and Excellent DurabilityThe upgrade aluminum flywheel for 212cc predator hemi engine is made of good quality aluminum material, with strong strength to ensure normal work condition.. Enhanced Safety Performance Machined for perfect balance, reducing vibration and the risk of failure at high speeds, while improving engine efficiency.. Package Include1Aluminum Flywheel.

Fitment This 8 flywheel timing key carburetor jet kit fit for Predator 212cc 196cc 224cc 60363 68121 68120 69727 69730 hemi and non-hemi engine, Hond GX160 GX200 6.5hp 7hp clone engine, Tillotson 212cc 196cc 225cc 236cc 268cc, Ghost 212cc etc. Meet your mini bike, go cart, generator, lawn mower, snow blower, water pump, log splitter, edge cutter, pressure washer, tiller equipped with the above engine. Wide Compatibility The 212cc carburetor main jet kit and 8 flywheel offset timing key is compatible with Coleman CT200U BT200X CT200U-EX CT200U Trail CT200U-A CT200U-EXR RB200 B200R, Trailmaster 200X MB200-2, Baja Motorsports MB165MB200 mini bike, Coleman KT196 BK200, Hammerhead 80T Mini Shark, TrailMaster163 Mini, 196 Mid, Buggy Interceptor go kart, Massimo MB200 and other vichels, go cart, yard equipment with above engine. Simple but Effective Replacement This 8 degree advanced timing key for Predator 212 can precisely fine-tune your ignition timing. For those racing drivers and mini bike enthusiasts who require high precision but do not want to bear the costs associated with adjustable hub flywheels, this is an economical solution. This flywheel offset timing key enables you to adjust the ignition advance angle or retard angle to meet the requirements of your specific engine configuration and fuel type. Excellent Durability Precise Dimension The mini bike carburetor main jet replacement is made of premium metal, offering corrosion resistance and high temperature resistance, ensuring its durability. The carb jets are manufactured with high-quality processes, featuring smooth surfaces and precise dimensions. They come in three models .036, .037, and .038. This allows you to adjust the carb jets as needed to achieve optimal performance. Package Includes 1X emulsion tube, 3X main jets.036 .037 .038, 1X 8 degree offset timing key.

Fitment The 212cc flywheel is fit for Predator 212cc 224cc 60363 only Hemi engine, Hond GX160 GX200 6.5hp clone engine, Tillotson 212cc, and Harbor Freight. Our aluminum flywheel for Predator 212 is compatible with Coleman CT200U CT200U-EX BT200X, Axi M200, Baja Warrior MB165 MB200 Mini Bike Yerf Do, KT196 Go Cart, Lawn Mower, Generator, and other vehicles equipped with the engine above. High Efficiency Our aluminum flywheel for predator 212 hemi was designed with low drag precision, providing you with a smooth and accelerated riding experience. The excellent motor speed of up to 10000 rpm allows your vehicles to rev quicker and more powerful. The built in timing advance of the flywheel generates a stronger and longer spark to increase fuel combustion efficiency. Sturdy Durable The flywheel for Predator 212 hemi performance parts is made of high-quality cast aluminum material, with the function of sturdy, heavy-duty, and wear resistance, ensuring the most outstanding engine. Not like metal flywheels, aluminum flywheels can better dissipate heat during operation which helps the engine under normal operating temperature. Easy Installation and Replacement The 212cc Hemi flywheel comes with 2pc 26lb valve springs, 1pc crankshaft key, and 1pc 8 flywheel offset timing key, to meet your different needs. No need for complicated tools, you can complete the installation and replacement in a few minutes. Package Includes 1X aluminum hemi flywheel, 2X 26lb valve springs, 1X emulsion tube, 3X main jet.036 .037 .038, 1X metal flywheel crankshaft key, 1X 8 degree offset timing key, 1X spark plug. Note There may be cracks like the hairline on the flywheel due to the integrated forging process during production. Please don't worry, it is normal and the flywheel can continue to maintain reliability.

Fitment Ultra-Light Billet Aluminum Flywheel for Honda GX200Clone, Clone 196cc, Ducar 196212 and Tillotson 196225228236, WildCat 223, Predator Ghost 212, and Predator 224cc NON Hemi Engines.. Featherlight Design Weighs 1.69 LBS, Lightest Flywheel Available. Delivers more sensitive and stable power output at high speeds, optimizing your engines efficiency.. Features a finless drag racing design that will greatly reduce air drag on your Junior Dragster or Drag Mini Bike racing engine. Less air drag on the flywheel means more power freed up throughout the power curve, especially on the top end.. Premium Quality This ultra-lightweight flywheel is precision-machined from high-strength 6061-T6 aluminum, delivering exceptional durability and performance under extreme conditions. Rare-earth magnets insuresreliable Ignion.For optimum performance we recommend running with a balanced rotating assembly.. SpecificationFlywheel is set at 32 degrees with a stock key.Minimum .030 coil gap.Torque to 54 ftlbs. IMPORTANT NOTE Will work with stock coilshims included and fins. We recommand the flywheel works with PVL ignition coils..

Fitment Aluminum flywheel replacement for non hemi predator 212cc 224cc ghost 208cc 69730 69736 GX160 GX200 196cc BSP Tilly Clone engine. Not for Predator Hemi Engine. Compatibility The 224 flywheel compatible with Coleman CT200U BT200X CT200U-EX, Baja Warrior MB200 MB165, Massimo MB200 MB165 mini bike and KT196 go kart. Advantage This durable predator 212cc billet flywheel is certified by SFI. It is designed with aluminum valve cover and steel center hub. Unique Design Special low drag fan is designed for the ARC flywheel, creates minimal air drag. So it will help your mini bike run more smoothly. Feature This 212 billet flywheel uses a high strength rare earth magnet to build and have more magnet more than the original one. It features an 8 degree built in timing advance to bring the ignition timing to 32 degrees TDC. The built in timing advance allows you to utilize the stock flywheel key with no grinding or offsetting necessary. Note Please check the size and pictures carefully to make sure it's what you want.

Predator 212 Stage 2 assembly for 6.5HP7.5HP Predator 212cc196cc Clones Engine,GX160GX200 Clones, Harbor Freight Predator 60363 68121 68120 69727 69730,Tillotson 212cc, Coleman Baja Trailmaster Mega Moto 196cc 200cc 5.5hp 6.5hp Powersports Mini Bike Go Kart. Compatibility VM22 Carburetor Predator 212 for Predator Hemi Non-Hemi 212cc Engine, Coleman Powersports CT200U CT200U Trail 200 BT200X KT196 RB200 , GX200 6.5HP GX160 5.5HP OHV engine, Baja Motorsports Mini Bike MB165 MB200 Heat, Mini Baja, Warrior , TrailMaster Buggy Interceptor MB200-1 ,MB200-2 , Harbor Freight Predator 60363 68121 68120 69727 69730 6.5HP7HP 212cc Engine RATO R210-III , Monste Moto Mega Moto Mega Max MM-B212MX,MM-B212PRO,. Reduce fuel consumption with our Predator 212 Parts wth Predator 212 Exhaus, 212cc Carburetor, resulting in quick start and smoother running, it will be the good choice of modification with aesthetics and practicality. Please check the size ,color and ,model in the item picture and description carefully before purchasing. Also you can leave us messages if you don't make sure the item or any other after-sales issues.. Package List 1 212cc Carburetor, 1 212cc Exhaus Muffler, 1 Inlet Pipe Manifold, 1 Fuel Filte, 1 Fuel Line, 1 Throttle Cable, 3 Wrench, 6 Screw, 2 Nut, 3 Gaske.

Fits Honda gx200, Clone 196cc BSP Tilly and for Predator 212cc NON Hemi, 224cc New Ghost 212cc engine. Fits Predator 224cc max power engine. will not fit the hemi predator engine.

Brand New High Quality Flywheel With Magneto Charging Coil For Harbor Freight Predator 212CC R210III Non-hemi Gas Engine. Please Note Our flywheels fit 0.68 Shaft. However, there are other size shafts 0.65 and 0.71 in market. Please check the flywheel size bore size before placing the order. It is because Predator purchases the same model engine from different manufacturers.. Please check the plug type on the charging coil and compare with your head light plug before placing order with us.. Package includes 1X Flywheel With Magneto 2X Charging Coils.

FitmentGX160 GX200 5.5HP 6.5HP. Package Include1flywheel1charging coil. Flywheel material is made of iron, magnetic flywheel has magnetism, the quality is good and not easy to damage.. Match original equipment exactly for a perfect fit, easy to install.. Please check for the details and make sure this is the right one you need..