Provides an attachment point for push-button slings. Machined from Mil-Spec anodized aluminum. Beveled edges to reduce snagging Anti-rotation design that prevents swivels from spinning. All hardware necessary for attachment directly to M-LOK Slots is included. No modifications to the M-LOK mounting location is required.

Factory-installed Magpul QDMs constructed of Melonite finished steel for strength and extreme resistance to wear and corrosion. Dedicated two-point sling that can be configured for multiple functions with optional adapters. Secure and rapid length adjustment with MS1 Slider No tails, loops, or other potential snag hazards. Lightweight, yet durable slider and buckle hardware made of reinforced engineering polymer. Proprietary weave, 1-14 wide nylon webbing is strong and abrasion resistant while tubular construction provides anti-chafing user comfort Colored webbing has Near Infrared NIR treatment to reduce IR signature.

Made of lightweight Mil-Spec hard anodized 6061 T-6 aluminum and Injection-molded polymer Aesthetically pleasing, low-profile design conceals its mechanisms and hardware, smoothly brushing off snags and bumps. Optimized for rapid one-handed adjustments quickly and quietly transitions between countless user configurations. Easily loaded with stabilizing forward tension without fear of failure or warping At just over 11 ounces, the Magpul bipod is lighter than many pricier bipods currently on the market. Spring-tension legs stow neatly forward and snap down and lock into place with one hand Leg extensions slide and lock securely with the push of a button on any of the seven half-inch spaced locking detents. An industry-exclusive 50 degrees of total tilt and 40 degrees of total pan are controlled by a glove-friendly knurled tool-less bipod locking knob located between the extended legs, allowing easy adjustment between shots.

Made of high quality aluminum construction with black anodized finish.. Fits on rails and works with the most common bipods in the market,can also be used as a sling stud when bipod is removed.. Upgraded T-nuts design increases width to provide a sturdy support for bipod. Two convex blocks on both sides can resist much more recoil to provide a solid stability.. Comes with extra set of the screws and T-nuts for further using.. Enhanced sling stud won't strip off..

Can be installed on the opposite side to add additional push-button QD Sling Swivels or our own Magpul QDM. For running ambidextrous sling swivels on the SGA, MOE rifle, MOE fixed, hunter 700, and hunter X-22 stocks, this type 2 kit must be utilized in conjunction with the optional Type 1 kit MAG333. Heavy-duty Black phosphatized steel construction easily installs with The UBR or STR's original hardware, or with the hardware included with the Type 1 kit. Swivels not included Made in USA. NOTE Type 2 Kit must be utilized in conjunction with the optional Type 1 Kit in order to run ambidextrous sling swivels on the SGA, MOE Rifle, MOE Fixed Carbine, Hunter 700, and Hunter X-22 Stocks.

Mounts to all M-LOK compatible attachment points. Coated steel loop accepts up to 1-14 Sling webbing. Base machined from Mil-Spec anodized aluminum for durability and light weight. Beveled edges and low profile reduces snagging. Recoilimpact mitigation lugs and cammed T-Nuts for mounting.

Push-button quick-detach sling swivel for 1-14 webbing. Manganese-phosphate finished steel. Compatible with QD sling attachment points. Combine with MS1 sling for dedicated two-point sling or with MS1 MS4 adapter. Made in USA.

Heavy-duty upgrade to standard push-button sling swivels Innovative design allows for a lower profile sling swivel that offers one-handed manipulation. High strength bale rotates freely and canalizes sling webbing to prevent rollover. Custom QD sling swivel for 1-14 webbing Dual side release tabs prevent accidental release. Melonite finished steel for strength and extreme resistance to wear and corrosion. Combine with MS1 Sling or with MS1 MS4 Adapter Fits all standard sized QD cups.

Floorplate replacement for current issue aluminum USGI mags. Incorporates an integral loop, floorplate lock, and mag identifier. Provides unsurpassed speed and controllability during high stress, tactical mag changes. Loop is made of pliable Santoprene rubber overmolded onto a stainless steel plate. Patented design based upon the tried-and-true paracord loops and duct-tape tabs currently in use with special units worldwide Made in USA.

Mil-spec hard anodized 6061 T-6 aluminum. Stainless steel internals. Spring-tensioned legs stow neatly forward and snap down. Leg extensions slide and lock securely with the push of a button. Staggered soft rubber feet hold fast on a variety of shooting surfaces.

Includes front and rear folding back-up sights. Black case-hardened steel finished with Melonite QPQ. Dual aperture, windage adjustable rear and no-tool, elevation adjustable front. Fits 1913 Picatinny rail mounting applications, including rail-height gas blocks. Made in the USA.

Item Package Dimension 8.74L x 3.18W x 0.78H inches. Item Package Weight - 0.10 Pounds. Item Package Quantity - 1. Product Type - GUN SUPPORT.

Made using the highest quality materials. Tested for durability. Designed to be safe and unique.

Floorplate replacement for the 308 PMAG LRSR GEN M3 mags. Incorporates an integral loop similar to the original Magpul USGI Ranger. Provides unsurpassed speed and control during high stress, tactical mag changes. Made in USA. NOTE Dedicated fit for all 308 LRSR GEN M3 PMAGS and will NOT fit the older PMAG 20LR mag, or AKPMAGS, or any metal mag.

Impact resistant polymer construction provides light weight and resists operational abuse. Spring-loaded flip up sight easily activated from either side or by pressing the top. Detent and spring pressure keeps sight erect but allows for unobstructed folding under impact, etc.. Clamps to most any MIL-STD-1913 PicatinnySTANAG 4694 rail and provides the same height-over-bore as standard A2 irons. Protective wings shield the spring-locking A2 front sight post Elevation adjustment tool included, but most aftermarket A2 front sight adjustment tools may be used as well.

Spring-loaded, folding back-up sight. Same plane dual flip apertures. Lightweight reinforced polymer construction. All mounting hardware included.

Package length 20.32 cm. Package width 10.921 cm. Package height 1.524 cm. Product Type SPORTING GOODS.

Made from reinforced polymer and an anodized aluminum bedding block Offers users a cost effective fixed stock replacement featuring enhanced ergonomics. Compatible with Remington 700 Short Actions, this stock?requires no bedding and is a true drop-in solution for the end user Fits right-hand receivers only M-LOK compatible to accept a broad range of accessories. Compatible with our?Bolt Action Mag Well 700?which allows the rifle to be used with detachable AICS-spec box mags without the need for custom inletting. Compatible with standard Remington 700 pattern?short action rifles with stock Remington floorplates. Reinforced polymer shell with Type III hard anodized, machine finished, A380 cast aluminum V-bedding block Accepts ALL factory Remington barrels.

Made from reinforced polymer and an anodized aluminum bedding block Offers users a cost effective replacement fixed stock featuring enhanced ergonomics. Compatible with Remington 700 Long Actions, this stock?requires no bedding and is a true drop-in solution for the end user Fits right-hand receivers only M-LOK compatible to accept a broad range of accessories. Compatible with our?Bolt Action Mag Well 700L?which allows the rifle to be used with detachable AICS-spec box mags without the need for custom inletting. Compatible with standard Remington 700 pattern?long action rifles with stock Remington hinged floorplates. Reinforced polymer shell with Type III hard anodized, machine finished, A380 cast aluminum V-bedding block Accepts ALL factory Remington barrels.

Made from reinforced polymer and an anodized aluminum bedding block Offers users a cost effective replacement fixed stock featuring enhanced ergonomics. Compatible with Remington 700 Long Actions, this stock?requires no bedding and is a true drop-in solution for the end user Fits right-hand receivers only M-LOK compatible to accept a broad range of accessories. Compatible with our?Bolt Action Mag Well 700L?which allows the rifle to be used with detachable AICS-spec box mags without the need for custom inletting. Compatible with standard Remington 700 pattern?long action rifles with stock Remington hinged floorplates. Reinforced polymer shell with Type III hard anodized, machine finished, A380 cast aluminum V-bedding block Accepts ALL factory Remington barrels.

An ergonomic, full-featured Stock for the ubiquitous ruger?1022?rifle drop-in design compatible with all factory Ruger 1022 .22 LR receivers no gunsmithing Necessary. Features an ergonomic grip, adjustable length of pull and comb height to fit a wide variety of shooters reinforced polymer construction for strength and durability. Multiple sling mounting options, a non-slip rubber butt-pad, and m-lok slots for accessory attachment. Reversible barrel tray ensures proper fit with factory pencil profile as well as heavy bull barrels optional cheek riser kits to raise cheek height 0.25, 0.50, or 0.75. Compatible with all capacities of factory Ruger 1022 magazines 60 degree grip angle from bore axis.

Designed for use with the Magpul Hunter X-22, Hunter X-22 Takedown, SGA Shotgun Stocks, Hunter 700, Hunter 700L, and Hunter American stocks. Allows the user to configure their firearm with the ideal cheek piece height. Accommodates a wide range of sightoptic configurations and shooter preferences. Available in two configurations, Low 0.25 - 0.50 and High 0.50 - 0.75. Made in USA.

The most versatile addition to the Magpul line of slings. MS1 slider provides rapid adjustments to either lengthen or shorten the sling with no slipping once set, and no tails, loops, or other potential snag hazards. Allows for easy shoulder transitions, rapid adjustability for hands free carry and shooting support from various positions. Custom 1-14 wide nylon webbing material is strong and wear resistant while remaining anti-chafe for user comfort Colored webbing has Near Infrared NIR treatment to reduce IR signature. Survived testing with tens of thousands of cycles in wet, dry and sandy conditions, static load testing without slippage for 72 hours and weighted six foot dynamic drop tests. Dedicated two-point sling. Rapidly adjustable for length shorter or longer with new MS1 Slider. No tails, loops, or other potential snag hazards. Coyote Brown in color.