Boat Keel Protector - Protect your boat keel from rocks, oyster beds, sand, concrete ramps and docks, abrasive wear and tear under water, saves the keel from constant abrasions, scratches and scars. Save the keel from any future possible damage with our keel guards and save the cost of boat repairing form continuous shore landing.. Boat Compatibility - Compatible with fiberglass and some aluminum boats. Keel guard for Recreational watercraft Ski Boats, Skiffs, Dinghy and most Jet Boats, fiberglass boats Bass Boats, Ranger Bass Boat, Ski Boats, Wake Boats, Runabouts, Some aluminum boats Fishing and Jon Boats.. Premium Workmanship - The keel protector for boats is produced from thick and durable rubber that absorb the shocks and impacts with maximum protection on your boat keel. The rugged and flexible 5 inch wide boat hull protector conforms to your boat's keel easily and won't drag your boat down.. Superior Craftsmanship - The keel guard using strong 3M adhesives for maximum adhesion to boat, the tough yet soft 5-inch wide boat keel protection conforms to your boat's keel easily and firmly, and the drag reduction channels that won't slow your boat down. 9.6 Feet Length.. Easy to Install - The boat keel protector features an self-sealing contoured edge that creates a tight seal for long lasting protection. Only take 5 steps without sealants needed delimit, etch, clean, prime, apply. Warm tips keel primer was not included in the kit..

The SeaSierra skeg cover guard protector kit provide ultimate protection for your new skeg or repair an impact-damaged or chipped skeg for improved performance. Fit MerCruiser 1991-Up Alpha One 1 Gen 2 out drive. Replace part number 27031, 35-SS610. The skeg protector Guard is crafted from 316 stainless steel with a fine mirror-polished surface to ensure it fits perfectly on your Skeg. To install, you simply leave 2 to 3 inches of the original skewer in place, align the keel cover guards with the tail fin, tap gently with a rubber mallet until it fits perfectly, drill the holes with a 14-inch drill bit, and install the stainless steel hardware.

SHIN GUARDS WITH OPTIMIZED INSERT POCKET - NO MORE SLIPPING OUT Did you have a situation where the shin guards slipped out during a game This is a common problem with shin guards, but now we find a new solution. The included sleeves not only have a slide-in compartment for the shin guards to go into, but also have an extra lid on top so that help the shin guards stay in place and don't fall out the top.. BREATHABLE MATERIAL The thickly padded inside with the small elastic cushions against the impacts and guarantee optimal air permeability. The soccer shin guards also ensure sufficient air supply through the mesh fabric. The shin guards do not stick directly to the skin and sweat is better absorbed.. RELIABLE QUALITY The hard pad is thick and very durable. The molded leftright protective pad provides an ideal fit and contoured comfort. Thanks to the minimalist print and carbon texture on the surface, the shin guards look very elegant.. FOR CHILDREN ADULTS This shin guard is comfortable to wear and provides the best possible protection during the game. The pad is available in 4 sizes and suitable for all soccer players.. PURCHASE WITHOUT RISK - We attach great importance to the customer satisfaction and quality. If there is any problem with our soccer shin guards, please dont hesitate to contact us. We will definitely find a solution.

Ultimate ProtectionOur boat keel guard device can resist underwater threats such as abrasive sand, sharp rocks, and concrete ramps, significantly reducing daily scratches and wear, effectively avoiding keel damage, and helping you save high repair costs. Multi boat applicationKeel guard specially designed for fiberglass boats Bass boats, ranger Bass boats, ski boats, etc., some aluminum boats fishing boats, Jon boats and leisure boats Dingji boats, most jet boats, which can be fitted with micro convex Flat noodles, with sealant to fill the gap, with strong adaptability. High quality materialKeel guard for aluminum boat made of high-density polyethylene HDPE and glass fiber reinforced plastic FRP, it combines high hardness and toughness, efficiently absorbs impact, closely adheres to the keel without increasing navigation resistance, and provides long-lasting protection. Strong adhesionKeel shield keel guard equipped with a complete set of installation tools, strong adhesion. Simply complete the steps of surface treatment, marking, etching, cleaning, primer application, and pasting to achieve a stable installation. Flexible protectionThe 6-foot length specification boat keel guard protector is suitable for ships under 18 feet, and it is recommended to install beyond the lowest point of the hull to prevent grounding and hook pulling. The length can be extended as needed to meet diverse protection needs.

Ultimate Keel Protection Our keel guard effectively shield your boat keel from abrasive sand, sharp rocks, concrete ramps, oyster beds, and other underwater obstacles, significantly reducing scrapes and wear and tear during daily use. Protect your keel from potential damage and save on future repair costs with our durable keel guards.. Wide Compatibility Our keel guard are designed for fiberglass boats Bass Boats, Ranger Bass Boat, Ski Boats, Wake Boats, Runabouts, some aluminum boats Fishing and Jon Boats, and recreational watercraft Ski Boats, Skiffs, Dinghies, and most Jet Boats. The guards can be applied on slightly raised strakes and chines with the included sealant for gap sealing.. Superior Craftsmanship Our keel guard for fiberglass boat are made from high-density polyethylene HDPE and fiberglass-reinforced plastics FRP, providing excellent hardness and durability. These materials effectively absorb shocks and impacts, offering maximum protection for your boat's keel. The rugged yet flexible design easily conforms to your boat's keel without adding drag.. STRONG ADHESION FOR EASY INSTALLATION Our keel guard for fiberglass boat feature strong self-adhesive 3M Marine Adhesive Sealant 5200 for a secure, tight fit. Simply follow these steps prepare hull surface, scribe, etch, clean, primer and attach. Size Guide The 6-foot Keel Guard fits boats up to 18 feet. For optimal protection, apply the guard beyond the lowest point of the boat to prevent snagging and tearing during beaching or loading. The length can be extended but not shortened.. Buy with Confidence We stand behind our keel guards with a robust warranty and responsive customer service. If you have any issues or questions, our dedicated team is ready to assist you within 24 hours..

The skeg protector fits Mercury 75 90 115 HP 4 stroke Command Thrust SeaPro 4.25 GC, 2.38 2014-Present, 135 150 175 200 225 HP 4 stroke Verado 4.8 GC 2005-2018 and 150 HP 4 stroke ProXS SeaPro 4.8 GC 2019-Present outboard models. Also compatible with Mercury 200 225 250 HP 2 stroke Optimax ProXS No Torquemaster 1999-2018 and 200 250 300 HP 4 stroke PRO Verado 4.8 GC 2015-2018 outboard engines. The lower unit skeg replacement kit effectively protects the skeg from abrasion, scratches and damage caused by rocks, hidden debris and other underwater objects. Made of premium marine-grade 316 stainless steel. Higher strength, mirror-polished, better anti-corrosion and wear resistance. The drain hole designed on the bottom of skeg protection prevents water from pooling and stagnating inside, so as to reduce the risk of corrosion. Thickened 3mm lower wear tab reduces ramp dragging.

Strong and durable keel protection Made of high-density wear-resistant material, it can effectively resist strong impacts and scratches from rocks, oyster beds and coastlines. Provides long-lasting and reliable protection for fiberglass and aluminum hulls, significantly reducing the risk of wear in the keel area and extending the service life of the hull.. Strong self-adhesive, easy DIY installation The back comes with industrial-grade strong adhesive, which can be quickly attached without complex tools or professional construction. Tear off the protective film, align it with the keel and press firmly to enjoy solid protection. It is suitable for boat owners to operate by themselves, saving time and effort.. Widely adaptable to fiberglass and aluminum boats specially designed to be optimized for fiberglass and aluminum alloy hulls, with strong adhesion and no damage to the material surface. It is suitable for all types of small and medium-sized ships, rubber boats, sailboats and motor boats, and is an ideal choice for hull maintenance and upgrades.. Impact resistance, corrosion resistance, adaptable to harsh water environments The material has excellent impact resistance and salt water corrosion resistance, and can still maintain stable performance after long-term immersion or frequent docking. When sailing in complex waters such as reef areas, shoals, and oyster farms, it provides effective protection for key parts of the hull.. Simple white design, integrated into the appearance of the hull the white surface coordinates with most hull colors, and the overall appearance is not obtrusive after installation. Taking into account both practicality and visual effects, it improves protection capabilities while maintaining a clean and professional visual presentation of the bottom area of the ship..

COLOR White. WIDTH 4. APPLICATION Simple to apply. Guard comes with a pre applied layer of marine grade adhesive. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for kayaks, canoes, SUP boards, and catamarans..

Product Includes you will receive 1 pcs roll of kayak keel guard protection strip, 4 inches wide and 18 feet long This extra-long size can completely cover the keel of a single kayak, with extra length for reinforcement of easily worn areas such as the bow and stern It can also be cut to any length to fit different sizes of kayaks, canoes, paddleboards, and other water sports equipment. Reliable Material our keel guard for kayak is made of PVC polymer material, which is tough and wear-resistant, with excellent waterproof and moisture-proof properties It has excellent impact and scratch resistance, effectively resisting friction and impact from reefs, beach pebbles, and hard objects in shallow water, preventing scratches, cracks, and damage to the keel, extending the life of your kayak, and making outdoor adventures safer. Complete Installation Accessories includes a masking tape, pad, wet wipes, and a burning tool Masking tape helps position the protection strip to prevent misalignment, and a scouring pad is applied to polish the hull surface Removes oil, dust, and oxide layers, improving adhesion Wet wipes quickly clean residual impurities after sanding, leaving the bonding surface cleaner A scraper allows the protective strip to better conform to the hull's curvature, enhancing adhesion. Strong Adhesion and Easy to Cut the keel guard for fiberglass boat has a high-adhesion backing and is waterproofed, so its adhesion is unaffected by moisture It is not easy to fall off or lift, and can maintain a stable fit to the hull for a long time The PVC has excellent flexibility and can be bent freely to conform to the hull's curvature, adapting to different keel shapes such as flat bottoms and curved shapes Simply use scissors to precisely cut according to the boat's dimension. Widely Applicable this boat keel guard protection strip is installed on the bottom of kayaks and canoes It protects the hull and keel, providing protection for your boat The kayak keel protection strip prevents accidental contact with rough surfaces It prevents boats from being dragged on concrete surfaces and is suitable for kayaks, canoes, paddleboards, catamarans, jet skis, and many other types of boats.

INCLUDED Roll of PereGuard, Final Prep Wipes to ensure the surface is clean and promote strong adhesion, and detailed Instructions. COLOR Black and guard WIDTH is 4. APPLICATION PereGuard is simple to apply. Just peel off the backing paper and apply the guard. The guard comes with a layer of marine grade adhesive that is pre-applied. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The guard is thin to prevent drag, and the edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for kayaks, canoes, SUP boards, catamarans, and many other applications.

INCLUDED Roll of PereGuard, Final Prep Wipes to ensure the surface is clean and promote strong adhesion, and detailed Instructions. COLOR White WIDTH 6 Inches THICKNESS 18 Inch. APPLICATION Simple to apply. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for powerboats, catamarans, jet skis and pontoon boats..

INCLUDED Roll of PereGuard, Final Prep Wipes to ensure the surface is clean and promote strong adhesion, and detailed Instructions. COLOR Black WIDTH 6 Inches THICKNESS 18. APPLICATION Simple to apply. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for powerboats, catamarans, jet skis and pontoon boats..

INCLUDED Roll of PereGuard, Final Prep Wipes to ensure the surface is clean and promote strong adhesion, and detailed Instructions. COLOR Black and guard width is 2. APPLICATION PereGuard is simple to apply. Just peel off the backing paper and apply the guard. The guard comes with a layer of marine grade adhesive that is pre-applied. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The guard is thin to prevent drag, and the edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for kayaks, canoes, SUP boards, catamarans, and many other applications.

INCLUDED Roll of PereGuard, Final Prep Wipes to ensure the surface is clean and promote strong adhesion, and detailed Instructions. COLOR White and guard WIDTH is 2. APPLICATION PereGuard is simple to apply. Just peel off the backing paper and apply the guard. The guard comes with a layer of marine grade adhesive that is pre-applied. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The guard is thin to prevent drag, and the edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for kayaks, canoes, SUP boards, catamarans, and many other applications.

Full Coverage Combo Keel Bow Guard This all-in-one bow keel guard set provides complete protection for your boat's most vulnerable areas. It includes one 6ft keel guard to shield against underwater abrasions and two stainless steel bow guards to prevent damage during loadingtransport. Get peace of mind from water to land. Rugged Stainless Steel Bow Guards with Easy Installation This set includes 2 mirror-polished, rust-resistant bow guards that protect your bow from trailer roller scratches during loading and transport. Smooth edges ensure safe handling and a sleek appearance. To install 1 Apply adhesive to guard, 2 Clean and dry hull surface, 3 Bend guard to match hull curve, 4 Remove backing film, 5 Press firmly into place, 6 Remove surface film. Complete protection with a custom, secure fit. Durable Keel Guard Easy-to-Install Impact-Absorbing Made of thick, high-density rubber, this keel guard for boat absorbs impacts from sand, rocks, concrete ramps, and oyster bedsprotecting against scrapes and daily wear. Flexible yet rugged, it conforms smoothly to your keel without adding drag. Simple 6-step install Prepare hull Scribe Etch Clean Apply primer Attach. Note Keel primer not included in the kit. Save on Costly Repairs Double-Layer Defense The keel guard fights underwater abrasion, while the bow guards prevent trailer damage. Together, they significantly reduce cosmetic and structural wear, saving you money on maintenance and repairsa smart investment for your boat. Universal Fit Easy Installation This versatile bow keel guard set fits most boat typesincluding fiberglass, aluminum, and personal watercraft. The 5-inch wide keel guard flexibly contours to raised keels, while the pre-sized bow guards offer universal application. Both feature marine-grade adhesive for simple, secure installationjust follow clear steps. Together, they reduce damage from beaching, transport, and daily use, delivering lasting protection with one investment.

INCLUDED Roll of PereGuard, Final Prep Wipes to ensure the surface is clean and promote strong adhesion, and detailed Instructions. COLOR White and guard WIDTH is 4. APPLICATION PereGuard is simple to apply. Just peel off the backing paper and apply the guard. The guard comes with a layer of marine grade adhesive that is pre-applied. Clean the surface, peel off the backing paper off the Guard and then apply the Guard. PereGuard works on thermoformed boats, fiberglass, rotomold plastic, aluminum, and many other materials.. DESIGN PereGuard is made from durable PVC and has a smooth surface to reduce friction in the water. The adhesive is industry strength and works well in all environments. The guard is thin to prevent drag, and the edges are tapered to seal with the boat and keep dirt and grime away from the adhesive layer.. USES Ideal for kayaks, canoes, SUP boards, catamarans, and many other applications.

The 27151 skeg protector guard fits Yamaha outboard 150-175 HP 24 stroke 1984-Present, 200 HP 2 stroke HPDI VMAX HPDI 2000-2012, 200 HP 4 stroke 2.8L I-4 2012-Present, 300 HP 4 stroke 2007-2009, 350 HP 4 stroke 2007-Present and Yamaha sterndrive IO out drive motor engines 1989-1993. The lower unit skeg replacement kit protects your skeg from corrosion and wear in the harsh marine environment, as well as from scratch and damage caused by ramp dragging and hidden debris. Made of premium marine-grade 316 stainless steel and features a 3mm lower wear tab, the drain hole on the bottom also prevents water from collecting and causing corrosion or freezing. Can be installed with as little as 2 to 3 inches of the original skeg remaining, suitable for repairing a broken damaged skeg. Package includes all necessary accessories as the pictures shown, easy to install, ideal for DIY, just fix the skeg protector in place and tighten the screws Can Use Rubber Mallet for Proper Fit.

Maximum Impact Protection for High-Wear Areas The Bumper Bro is a premium kayak accessory designed to deliver abrasion resistance for the keel, bow, and hull. This molded ABS protector guards the bottom of your kayak from rocks, ramps, and rough launches, providing dependable kayak protection and long-lasting keel protection.. Built Tough with Heavy-Duty ABS Construction Crafted from thermoformed ABS polymer, this kayak keel guard is denser and tougher than standard kayak hull material while remaining flexible. Acting as a durable boat hull protector, it adds an extra guard layer that helps reduce scratches, impact damage, and long-term wear.. Quick, Tool-Free Installation That Saves Your Hull This Hobie kayak accessory installs easily on the front or rear underside of your kayak. Designed to absorb wear and tear instead of your hull, it functions as an effective kayak keel guard protector without drilling, complex tools, or permanent modifications.. Engineered for Keel, Bow Bottom Defense Designed to protect the most exposed areas, the Bumper Bro serves as an abrasion-resistant kayak guard for the keel, bow, and bottom surface. Ideal for frequent launching, beaching, trailering, and transport, it helps prevent costly hull damage over time.. Model-Specific Fit Sold Individually Sold individually, allowing you to choose either a bowfront or sternrear keel guard based on your needs. This model-specific kayak accessory is compatible with Hobie Outback, Hobie Pro Angler 12, Pro Angler 14, Hobie Compass, Hobie Passport, and Hobie Lynx kayaks for a secure, precision fit..

Product specifications Length 6.5 Feet Width 5 inches Thickness 0.276 inch. And you will get a pair of glovescolor in random, sandpaper, a scraper, and a roll of tape together, a super valued pack for you.. Shock Absorption Impact Protection Crafted from marine-grade polymer, our keel guard absorbs 50 more impact than standard guards, shielding your boat from rocks, concrete ramps, and oyster bed scratches. UV-resistant, uperior impact absorption and corrosion resistance, prevents sun degradation, strong to withstand reef collisions, shore stranding, and abrasive marine environments.. Compatibility The 5-inch wide flexible keel guards protector adopt ipple-channel design disperses impact force conforms to most keel contour without added drag. Designed for fiberglass boats basswakeski boats, aluminum hulls jon boatsdinghies, and personal watercraft. Excludes LSE kayakscanoes and catamarans with 90 upturned keels.. Boat Keel Protector Available in 6.5ft lengths fit boat size up to 18 ft. Extendable but not shortenablenever shorten pre-cut units Recommand install 2 beyond keels lowest point for complete protection.. Easy to Install Includes waterproof sealing primer, keel guards, scraper and sand paper, these keel boat cover with strong adhension and provide firm and tight application no clamps needed just etch, clean, and press for permanent installation, avoid contact with bunksrollers for 72 hours.. 100 Satisfied Service We stand behind our keel guards with a robust warranty and responsive customer service. If you have any issues or questions, our dedicated team is ready to assist you within 24 hours..

What You Will Get you will receive 1 roll of black keel guards, the appropriate quantity can meet your daily use, protection and replacement needs, you can use them for different ships, yachts and so on Before use, wipe the place to be pasted clean first, and the effect will be better after 24 hours of pasting. Proper Size the length of our kayak keel guard is about 23 feet 7 meters, the width is about 4.72 inches 12 cm, and it is about 0.11 inches 0.28 cm thick, please check the size carefully before ordering to avoid misunderstanding. Detailed Material our keel guard for fiberglass boat is mainly made of rubber, so it is wear resistant, not easy to break or deform, and can be applied for a long time, you do not need to buy another ones in short term. Easy to Stick our keel protector is thoughtfully designed and can be easily adhered, you just need to tear off the paper on the back, and then you can directly paste it on the boat, which is very convenient. Widely Applied our keel guard for kayak can be applied to most kinds of boats, suitable for kayaking, inflatable boats, fiberglass boats, aluminum boats, etc., which can help prevent scratches, scars and more.

ApplicationSkeg Shield is designed to repair or replace the skeg for prop protection. Compatible for Volvo Penta SX Drive Single Prop engines made between 1995 and 2006. FunctionRepair or replace your boat's skeg to keep the prop protected with our Skeg Guard for Volvo Penta SX Drive Single Prop Engines.. Upgraded Design The reinforced lower edge helps ensure protection against damage, while the drainage holes helps reduce water retention help to prevent corrosion and rust... MaterialMade with high quality 18 gauge 316 marine stainless steel with a polished mirror finish, this skeg guard delivers long-lasting performance and strength.. Slide-Drill-Bolt InstallationOur inboardoutboard skeg protector installs in as little as 10 minutes Just 3 steps, . You just slide the skeg guard into the skeg and tap it into place, drill your holes and tighten the locking bolts. No welding and no epoxies required.

For DIY Thermoforming Kydex V Thermoform Sheet is very similar to other thermoform sheet materials like Holstex and Boltaron in the way it forms when heated and molded around an object. Once cooled, this material will keep the shape of the item that was used to mold the shape into place. In its cooled state, it is very durable and light weight. It is used widely in thermoform holster making, cosplay costume creation, removable surface coverings, keel guard protectors, and much more.. Color Black KYDEX Type V Texture P1 Hair Cell The texture applied to the surface of the Kydex V sheet is referred to as P1 Hair Cell. This is a reference to the size and shape of the texture grain and is common on many Kydex items seen in the marketplace. P1 is the most common texture for holsters, sheaths, and other carry items. The texture on Kydex V sheet is uniform across the surface of the material and produces a non-reflective, scratch resistant finish.. Thickness .080 in. Easy To Form And Use To use Kydex V thermoform sheet, score and cut a piece slightly larger than the object being covered. Heat the material to a 300-375 degree Fahrenheit range and place over object. Using forming foam, press the material around the object and allow it to cool in position. Once cooled, remove and sand edges to desired shape. Detailed instructions included with order.. KYDEX V Sheet Material Is Made In The U.S.A. Kydex V sheet material is proudly made in the U.S.A. Each sheet is individually packaged and inspected by our staff. We take the greatest of pride in the products that we offer and stand behind every item sold. Order with confidence. Quantity 2 8 in. x 12 in. sheets nominal cut 100 Satisfaction Guaranteed With over 20 years of experience in developing holster making accessories, the thermoform sheet material line offered by Holstex is unsurpassed in the holster making and accessory industry. Our thermoform sheet materials are used by professional soldiers, police officers, public safety individuals, and holster makers worldwide. Each Kydex V sheet is individually inspected and guaranteed for quality..

Keel Protection for Everyday Use designed to protect your boat's keel from common hazards like gravel, sharp rocks, concrete ramps, oyster beds, and shoreline contact Helps prevent daily scuffs, scratches, and wear, reducing repair needs and keeping your hull in better condition over time. Hdpe Frp Composite for Impact Resistance made from a reinforced combination of high-density polyethylene and fiberglass reinforced plastic, this keel protector offers strong impact absorption while maintaining flexibility Effectively cushions shocks and vibrations during launching, docking, and shallow-water navigation. Fits a Wide Range of Boats compatible with most fiberglass boats and selected aluminum hulls, including jet boats, wake boats, speedboats, dinghies, pontoons, and aluminum fishing boats Designed to follow most keel lines and mild curvature without complex modifications. Low-profile Design Won't Affect Performance the 6-inch wide protective strip conforms closely to the keel for a secure fit without adding noticeable drag or resistance Maintains smooth water flow and handling while providing dependable bottom protection during normal operation. Installation, Stable Bonding equipped with self-adhesive adhesive backing, disposable gloves, sandpaper pads, polishing tools, the installation can be easily completed by following the steps of surface preparation, scribing and positioning, etching and cleaning, primer and pasting Note the primer needs to be prepared separately.

RELIABLE, LONG LASTING PROTECTION From rocks and concrete to ramps and docks, our keel guard is your boats first line of defense against damage Incredibly strong and durable, our hull guard helps protect against abrasions, scratches and scars.. VERSATILE DESIGN Whether you own a bass boat, a runabout or a recreational watercraft, our keel protector keeps your vessel in tip top shape Compatible with both fiberglass and most aluminum boats, it safeguards your precious investment.. DIY INSTALLATION Thanks to an exclusive 3M adhesion system, applying your keel guard is as easy as prep, peel, stick With no mixing or curing required, youll finish the job in an hour. The thickest marine adhesive around, it stays firmly in place.. MADE IN THE USA Combining the strength of pure Urethane Polymers with the quality of American workmanship, our protector kit is the one boaters trust Measuring 5 wide with lengths from 4 to 12 available in a range of colors, get a perfect match. LIFETIME GUARANTEE Were so confident in our boat keel guards, theyre backed with a limited lifetime guarantee against defects in materials or workmanship If you have any problems or questions, dont hesitate to let our customer service team know..

Ultimate Hull Keel Protection for Old Town Kayaks Safeguard your Old Town kayaks hull and keel from scratches, rocks, abrasion, and everyday wear with the BerleyPro Bumper Bro keel guard. This durable marine-grade accessory shields your kayak during paddling, docking, trailering, and fishing adventures. Perfect for recreational paddlers and anglers who want to protect their investment and extend the life of their kayak.. Superior Stability Tracking on the Water The keel guard not only protects your kayak but also preserves its natural tracking and stability. By maintaining a smooth hull and protected keel, you enjoy improved control, reduced drag, and efficient paddling. Whether navigating rivers, lakes, or coastal waters, your Old Town kayak performs better with enhanced maneuverability and stability throughout your trip.. Heavy-Duty Marine-Grade Construction Crafted from impact-resistant, high-quality marine materials, the Bumper Bro withstands sun exposure, water, and contact with rough surfaces. Resistant to flex, corrosion, and wear, it provides long-lasting durability for kayakers who demand reliable protection. Built to endure challenging paddling environments, this keel guard ensures your kayak remains in top condition for years.. Custom Fit for Old Town Kayaks Designed specifically for Old Town kayak models, this keel guard mounts securely along the hull and keel without interfering with handles, tracks, or other kayak accessories. Installation is simple, reliable, and provides a snug fit that stays in place, ensuring consistent protection and optimized performance on every outing.. Essential Accessory for Kayak Fishing Recreation Whether youre fishing, touring, or enjoying a casual paddle, the BerleyPro Bumper Bro keel guard is an essential Old Town kayak accessory. Protect your hull, maintain stability, and enhance your paddling experience. Perfect for all water conditions, this accessory gives you confidence to explore shallow rivers, rocky lakeshores, and coastal areas without worrying about hull or keel damage..

Durability Crafted from stainless steel, our Boat Keel Guard offers exceptional resistance to corrosion, ensuring long-lasting performance in marine environments. Perfect Fit our Boat Keel Guard is designed with a professional shape, and ensures a precise and seamless installation on your boat's keel. Easy to install The back is equipped with professional adhesive. You can quickly install it by tearing off the protective paper. This installation method is more convenient, faster and easier to operate. Included 2 Boat Guard. Please check the machine model number and part number before purchase to ensure that the purchased parts are suitable for your equipment.

Two Eyelets Design Our inflatable fender features a long cylindrical body with two eyelets on both sides. A ribbed texture on all sides enhances strength.. High Quality Boat fender is made of commercial strength marine vinyl, UV- Protector and chemically resistant ribbed body for unsurpassed durability and long time service.. Easy to Mount Double Eyelets Design can let you hang these fenders vertically or horizontally, it enables you to weave the rope through both holes or hang the fenders from one hole. Handy to Inflate The boat bumpers package includes 4 boat fenders, 4 inflating needle, 4 ropes, 4 fender adjuster and 1 hand pump. The fenders can be installed and taken off in a snap.. Protect the Boat It would execute at safeguarding your vessel during waves and protect it from docks, obstacles, other nearby vessels.

Heavy-duty Material Made of polyethylene with 3 layers a layer of permanent sealing adhesives, a layer of tough braided material and a layer of waterproof plastic film, which is long-lasting, tear resistant and supporting long-lasting use.. Great Adhesion Permanent adhesive patch to cover up or protect the underneath of your RV. When placed over holes and tears, the repair tape bonds tightly to the bottom closure material PERMANENTLY. Eliminate taping the rips and tears in your underbelly repeatedly.. Easy to Use Cut a strip of tape slightly longer than the opening, then stick the tape and press the edge of the tape firmly so that the tape can be tightly bonded to the underbelly material. It would stick stronger if using a blow dryer or heat gun, apply heat to the tape. Do not overheat.. Universal Use This tenacious tape can repair damages underneath RV caused by debris on the road or a tire blowout and repair mobile home underbelly damage caused by animals and people making repairs It was used to block off areas to prevent air, debris, or from entering.. Clean Before Using Thoroughly clean surface and ensure that the area around the torn part is clean and dry before applying the repair tape, otherwise the belly tape would be easy to peel off..

Package Includes you will receive 1 roll of boat keel guard protector, the proper quantity can meet your daily requirements for usage and replacement, and you can use them for different boats and yacht. Proper Size to Use our boat hull protector comes with an appropriate size, measuring about 4 inches 10.5 cm in width, 79 inches 200 cm in length and 2 mm in thickness, please confirm the size before purchase. Fine Workmanship our keel guard for kayak is light but strong, wear resistant and reliable, not easy to break or deform, allowing you to use it with confidence for a long time. Thoughtful and Considerate Design the boat keel guard protector is easy to use, and you can just tear off the paper on the back, determine where you want to paste it, then you can paste it on the boat. Widely Applicable in Daily Life this kayak keel guard can be applied to various kinds of boats, including but not limited to kayak, inflatable boats, fiberless boats and aluminum boats.

Heavy Duty Keel Protectionyou will receive 2 roll of black keel guards The red film on the surface of the product is a protective cover that needs to be removed before use.Protect your kayak, canoe, or boat hull from scratches, abrasion, rocks, sand, ramps, and shoreline damage. Designed for everyday marine use and long-lasting keel protection. Fast DIY Peel-and-Stick InstallationNo drilling, sanding, or complicated repair process required. Simply clean the surface, peel the backing, and apply directly to your kayak keel in minutes. Flexible Marine Grade MaterialMade from durable flexible rubber material that conforms easily to curved kayak hulls, canoe keels, and boat surfaces without cracking or lifting. Waterproof UV Resistant Adhesivethe length of our kayak keel guard is about 1.5 feet 0.46 meters, the width is about 2.95 inches 7.5 cm, and it is about 0.11 inches 0.28 cm thick.Built for freshwater and saltwater environments with strong waterproof adhesive that stays secure under sun, water, and outdoor conditions. Universal Fit for Most Watercraft Compatible with kayaks, canoes, paddle boards, fishing kayaks, fiberglass boats, aluminum boats, and small watercraft.

VESSEL NECESSITIES The bow guard can protect your vessel or yacht from being scratched or worn by rollers during loading, unloading and transportation, and can help you save a lot of expensive maintenance costs. The bow protection board is undoubtedly a necessary item for the sea activists. RELIABLE MATERIAL The bow guard is made of high-quality 316 stainless steel. This material has strong industrial strength, is very suitable for marine environment and is not easy to be corroded, and can effectively protect your vessel for a long time. And this stainless steel material is semi-soft, so you can easily and easily shape it into the radian you want. CONVENIENT INSTALLATION The back is equipped with 3M VHB professional waterproof adhesive. You can quickly install it by tearing off the protective paper. This installation method is more convenient, faster and easier to operate. We have attached adhesive aids to help you install more effectively. GOOD FITNESS This bow guard has been professionally designed and cut, and its moderate size and exquisite shape can fit your bow perfectly. USE SAFETY Our bow guard has been polished and polished, which makes it not only more beautiful, but also its edge is very soft and won't cause damage to your hands.

A MUST-HAVE FOR BOAT OWNERS The bow protector effectively prevents your boat or yacht from being scratched or worn by rollers during loading, unloading, and transport, helping you save on costly repairs. It's an essential piece of equipment for any boating enthusiast.. PREMIUM MATERIAL Made of high-quality 316 stainless steel, it offers excellent corrosion resistance and industrial-strength durability, perfect for marine environments. The semi-soft material allows you to easily shape it to fit your desired curve.. EASY INSTALLATION Features professional 3M VHB waterproof adhesive on the backjust peel off the protective film and stick it on. Includes adhesion promoter to ensure an even stronger bond.. PROFESSIONAL FIT Expertly designed and cut for an optimal fit, with precise dimensions and a refined shape to match the bow of your boat seamlessly.. SAFE AND STYLISH The surface is polished and finely crafted with an elegant wave pattern, featuring smooth, rounded edges. It not only enhances the overall appearance but also prevents hand injuries, making it safer and more comfortable to use..

Complete 2-pack Value this set includes 2 rolls of kayak keel guard, each roll is 6.1 meters 20 feet in length, offering great value and ensuring you have enough material for multiple repairs, replacements, or to protect a second watercraft. Heavy-Duty Protection keel guard for kayak is made of rubber, wear-resistant, tear-resistant and not easy to deform It can effectively resist the scraping and damage of hard objects such as rocks and oyster beds to the hull, thus extending the service life of the hull. Easy Self-Adhesive Application the back of boat keel guard comes with a strong adhesive backing Just remove the release paper and it can be directly pasted onto the hull keel without any additional tools The pasting effect is even better after 24 hours The operation is simple and efficient. Generous Size for Custom Fit each roll keel guard for canoe measures 20ft6.1m in length and 1.97in5cm in width, 0.28 cm0.11 inches in thickness, giving you plenty of material to trim and customize to fit the exact shape of your kayak, canoe, or small boat, fiberglass boats and aluminum boats. Versatile for All Watercraft kayak accessories are ideal for kayaks, canoes, rowboats, and small fishing boats, this DIY keel guard is a must-have accessory for any water sports enthusiast looking to extend the life of their equipment.

Lasting Solution Named Best Paddling Accessory by PSR, New Product Showcase two years in a row With superior reliability and strength, our canoe kayak keel guard is a long term solution to protect or repair your kayak from drops, skids and cracks.. Easy Installation Simply prep, peel, stick and cure in the sun for up to one hour making your patch 500 PSI strong, permanent and ready to use For a finished look, sand and paint to match your kayak.. Exceptional Combining the strength of polyester resin and fiberglass with a UV light activator makes our patch kit watertight and impenetrable. Bonds to HDPE, plastic, fiberglass, aluminum and wood surfaces.. Conveniently Designed Now in a 3x18 inch Keel Strip, it is easier to use than ever Simply cut to the size that suits your needs. Angled and curved surfaces No problem Moldable around curves, edges, dents or joints and suitable for any emergency repair.. Made In The Usa With over 25 years of experience, we take customers seriously If our waterproof Gator Patch Kayak Keel Guard doesnt meet your expectations, we proudly stand behind our product with our 100 assurance..

Enough to Use the package comes with 2 rolls of kayak keel guards in different colors, namely black and white, well to match and useful, which is sufficient for you to cater to your repair needs and replacement in daily life. Cuttable Size our kayak keel guard measures approx. 118 x 2 inches 3 x 0.05 meter in length and width, suitable for many types of boats, and you can cut a proper size according to your actual needs, bringing you a pleasant and reliable use experience. Reliable and Waterproof the keel guard for fiberglass boat adopts quality PVC material and with marine glue on it back, strong adhesion and durability, not easy to tear, deform, even break, solid and colorfast, which can serve you for a long period. Broad Application these kayak repair parts are a necessary and useful accessory for many boats, such as, kayak, inflatable boats, fiberless boats, aluminum boats and more, resistant to water, and can stop your boats from scratches. Practical and Stylish this boat guard features fine workmanship, and is designed with a cone shape which can fit your boats better and prevent your boats from getting ruined by sands, rocks, concrete ramps and other hard things, making you feel safe and comfortable to use.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. SkegGuard 27211 FITS Mercury 75-90-115hp Command Thrust, SeaPro 2014-Present, 135-150-175-200-225-250-275-300hp 4 Stroke Verado 4.8 Torpedo 2005-2018, 150hp 4 Stroke, ProXS, SeaPro 4.8 2019-Present, 200-225-250hp 2 Stroke Optimax and ProXS No Torquemaster 1999-2018, 200-250-300hp 4 Stroke PRO Verado 4.8 Gearcase 2015-2018.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. Designed for Specific Motors SkegGuard 27021 FITS Mercury MerCruiser Alpha 1 1985-1990. Additional models are available for inboard and outboard motors such as Evinrude, Johnson, Force, Honda, Mercury, Mariner, Nissan, Tohatsu, OMC, Suzuki, Volvo, and Yamaha.

Boat Bow Protector - Protect your vessel from trailer roller scuffs, scratches, and everyday wear and tear on the water with the Scuffbuster Bow Guard from Megaware that's perfect to add to your boat supplies. Easy to Install - This bow protector features a 3M adhesive that is easy to install in just 4 simple steps prep the surface, bend it to conform to your hull, peel off the backing and attach it to the surface while applying pressure use a rubber mallet to activate the pressure sensitive adhesive. Superior Engineering - Our boat bow guard is made with anti-corrosive, 22-gauge stainless steel metal with a mirror-polished finish and easily bends to your boat's hull to shield the gelcoat from minor damage when trailering great for fiberglass and most aluminum boats. The Perfect Size - The extra-large bow guard measures 9 x 8.75 inches to ensure a proper fit for standard-size or larger boats your boat bow will be well protected when docking so you no longer have to worry about damage to your hull or bow. Instructions Included - An instruction sheet is provided in each package and must be strictly followed so as to not compromise the full bonding capabilities of the 3M adhesive.

Material The kayak keel protector is made of ABS material, which is sturdy and durable, and can effectively protect the bottom of your kayak. Easy Installation - It is easy to install it on the front or rear underside of your kayak and takes the wear and tear instead of your kayak, follow the instructions, and you'll have your keel guard securely in placepackage does not include adhesive or tape.. Durable ABS Material - Made of high-density ABS material, our kayak keel ensures excellent durability and impact resistance, keeping the bottom of your kayak keel when in contact with natural rocks or modern cement.. Suitable Model - The kayka keel guard compatible with 2019 Out back, pre 2019 Out back, Com pass, Model Specific, please choose the model that suits your kayak.. After sales service- Were not into trapping our customers into a purchase theyre not happy with. If youre not totally satisfied with your new kayak keel guard, let us know.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. Designed for Specific Motors SkegGuard 27051 FITS Mercury MerCruiser Bravo 1 3 1990-Present Not Compatible with XR or Sport Master or Bravo 2 models. Additional models are available for inboard and outboard motors such as Evinrude, Johnson, Force, Honda, Mercury, Mariner, Nissan, Tohatsu, OMC, Suzuki, Volvo, and Yamaha.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. Designed for Specific Motors SkegGuard 27221 FITS Volvo SX Single Prop 1995-2006 NO SX-A. Additional models are available for inboard and outboard motors such as Evinrude, Johnson, Force, Honda, Mercury, Mariner, Nissan, Tohatsu, OMC, Suzuki, Volvo, and Yamaha.

Protect against abrasive sand, rocks, concrete ramps and oyster beds. Eliminate costly repairs. Enjoy the highest quality and superior engineering.

PROTECTS YOUR BOAT against abrasive sand, rocks, concrete ramps, and oyster beds. Eliminate costly fiberglass and gelcoat repairs to boat keel.. DO-IT-YOURSELF INSTALLATION in under an hour. Application kit includes a patented burnishing tool to ensure professional results.. SUPERIOR ENGINEERING - The Original DIY Keel Guard - Developed with boat designers 3M engineers. UV-STABILIZED COLORS don't fade or dull and last the lifetime of your boat. Made in the USA.. LIFETIME WARRANTY against abrasive wear and adhesion failure during normal use of your boat, for as long as you own your boat.. Recommended Sizes 4ft - Up to 14ft Boat, 5ft - Up to 16ft Boat, 6ft - Up to 18ft Boat, 7ft - Up to 20ft Boat, 8ft - Up to 22ft Boat, 9ft - Up to 24ft Boat, 10ft - Up to 26ft Boat, 11ft - Up to 28ft Boat, 12ft - Up to 30ft Boat. If the size of your boat falls between 2 sizes, order up for the additional keel protection..

Color Black KeelGuard Size 10' Boat Size up to 26' 3M Technology 3M Acrylic Pressure-Sensitive Adhesive Pliable Tough Research Technology Contoured Edge.

Length 8 ft. White.

Protects your boat from scuffs and abrasion caused by trailer rollers. Part Number 2637. Minimize Roller and Trailer Scuffs. Bend to Conform to Hull. Mirror Polished Finish.

Skeg Protector - Reduce wear and tear while protecting your skeg against damage from ramp dragging, rocks, debris, and submerged objects with the Megaware SkegPro - the makers of the original KeelGuard. Proper Protection - Our guard helps prevent corrosion and freezing on your skeg it also features a drain hole at the bottom to prevent water from collecting to ensure your boat doesn't become stagnant. Strong and Reliable - The skeg cover is made from 18 gauge marine grade 304 stainless steel with self-locking hardware and a mirror-polished finish. The easy do-it-yourself application ensures you'll have your SkegPro installed in less than 10 minutes. FITS MercuryMariner 135-150-175-200-225-250-275-300 4 Stroke Verado 4.8 Torpedo 2006-2018 Pro Verado 200-250-300hp 4 Stroke 4.8 Torpedo 2006-2018 200-225-250hp 2 Stroke Optimax Proxs 1999-2018 No Torquemaster Mercury 75-90-115hp 4 Stroke Command Thrust Sea Pro 4.25 Torpedo 2014-Present 150hp 4 Stroke ProXs, SeaPro 4.8 Torpedo 2019-Present. A Commitment to Excellence - Megaware KeelGuard is a family-owned business that revolutionized the keel protection industry with its patented, do-it-yourself keel protector in 1992. We offer a range of high-quality products to keep innovating and providing top-notch support for your investment..

What You Will Get you will receive 1 roll of black keel guards The red film on the surface of the product is a protective cover that needs to be removed before use The appropriate quantity can meet your daily use, protection and replacement needs, you can use them for different ships, yachts and so on Wipe the place to be pasted clean first, and the effect will be better after 24 hours of pasting. Proper Size the length of our kayak keel guard is about 5 feet 1.52 meters, the width is about 1.97 inches 5 cm, and it is about 0.11 inches 0.28 cm thick, please check the size carefully before ordering to avoid misunderstanding. Detailed Material our keel guard for fiberglass boat is mainly made of rubber, so it is wear resistant, not easy to break or deform, and can be applied for a long time, you do not need to buy another ones in short term. Easy to Stick our keel protector is thoughtfully designed and can be easily adhered, you just need to tear off the paper on the back, and then you can directly paste it on the boat, which is very convenient. Widely Applied our keel guard for kayak can be applied to most kinds of boats, suitable for kayaking, inflatable boats, fiberglass boats, aluminum boats, etc., which can help prevent scratches, scars and more.

Skeg Protector - Reduce wear and tear while protecting your skeg against damage from ramp dragging, rocks, debris, and submerged objects with the Megaware SkegPro - the makers of the original KeelGuard. Proper Protection - Our guard helps prevent corrosion and freezing on your skeg it also features a drain hole at the bottom to prevent water from collecting to ensure your boat doesn't become stagnant. Strong and Reliable - The skeg cover is made from 18 gauge marine grade 304 stainless steel with self-locking hardware and a mirror-polished finish. The easy do-it-yourself application ensures you'll have your SkegPro installed in less than 10 minutes. Designed for Specific Motors - Fits MERCRUISER Pre Alpha 1 Drives 1973-1984 Alpha 1 1985-1990 Alpha 1 Gen 2 1991-Present. MERCURY 40-50-60hp Bigfoot Command Thrust, SeaPro 2001-Present 75-90-115 2 4 Stroke 3.44 Torpedo 1984-Present 150-175hp Optimax, Proxs 1978-2018, 125-135-140hp 2 Stroke 1986-2012 SUZUKI 150-175-200-225hp 2 4 Stroke 1986-Present No AS, SS DF250T No SS or AP Models 2004-Present, and YAMAHA 200 4 Stroke V6 2002-2018 225-250hp 2 4 Stroke 1997-Present 200-250 Vmax Sho 25 2015-Present 300hp 4 Stroke 2010-Present, 300hp 2 stroke 2004-2006. A Commitment to Excellence - Megaware KeelGuard is a family-owned business that revolutionized the keel protection industry with its patented, do-it-yourself keel protector in 1992. We offer a range of high-quality products to keep innovating and providing top-notch support for your investment..

Skeg Protector - Reduce wear and tear while protecting your skeg against damage from ramp dragging, rocks, debris, and submerged objects with the Megaware SkegPro - the makers of the original KeelGuard. Proper Protection - Our guard helps prevent corrosion and freezing on your skeg it also features a drain hole at the bottom to prevent water from collecting to ensure your boat doesn't become stagnant. Strong and Reliable - The skeg cover is made from 18 gauge marine grade 304 stainless steel with self-locking hardware and a mirror-polished finish. The easy do-it-yourself application ensures you'll have your SkegPro installed in less than 10 minutes. Designed for Specific Motors - Fits Mercruiser Bravo 1 3 1990-Present Not Compatible with XR Sport Master Model. Also available for many Evinrude, Johnson, Honda, Mercury, Mariner,OMC, Suzuki, and Yamaha motors. A Commitment to Excellence - Megaware KeelGuard is a family-owned business that revolutionized the keel protection industry with its patented, do-it-yourself keel protector in 1992. We offer a range of high-quality products to keep innovating and providing top-notch support for your investment..

Boat Bow Protector - Protect your vessel from trailer roller scuffs, scratches, and everyday wear and tear on the water with the Scuffbuster Bow Guard with Notch from Megaware.. Easy to Install - This bow protector features a 3M adhesive that is easy to install in just 4 simple steps. Prep the surface by bending it to conform to your hull and peel off the backing. Attach the protector to the surface while applying pressure using a rubber mallet to activate the pressure-sensitive adhesive. Superior Engineering - Our boat bow guard is made with anti-corrosive, 22-gauge, 304 stainless steel metal with a mirror-polished finish. It easily bends to your boat's hull to shield the gelcoat from minor damage when trailering great for most fiberglass and aluminum boats. The Perfect Size - The regular-sized bow guard measures 5.75 x 4.5 inches to ensure a proper fit for standard-size or larger boats your boat bow will be well protected when docking, so you no longer have to worry about damage to your hull or bow. Instructions Included - Our informative instructions will help you achieve a full bond with the 3M adhesive to ensure it is properly attached.

Keel protector kit comes ready to install with strongest, thickest 3M marine adhesive available, Guaranteed to last the lifetime of your boat. Easy, Do It Yourself Installation - just Prep-Peel-Stick, Installation does not require time to cure. 100 Made in the USA - Strongest and most durable protection for boat keel from abrasions, scratches, and scars. 5 width, made of pure Urethane Polymers and available in 9 colors and sizes 5', 6', 7', 8', 9', 10', 11', 12'.

Material PVC Color Black Finish Matte. Overall Dimensions 1 12 W x 10 L x 1 34 H. Edge Fitment 1 14 W x 18 H. Mounts 2 18 Dia. mounting holes approximately 5 apart, CTC. Sold as seen in pictures. Customers please note every computer shows colors differently. All measurements are approximate. Hardware and instruction installation manual not included.

ConstructionCrafted from high strength aluminum material, this withstands harsh marine environments and delivers reliable protection season after season. DurabilityEngineered for outstanding abrasion resistance, this protector protects your hull from scrapes, scratches, and impacts caused by concrete ramps, shores, and rough coastal sand. Versatile CompatibleSuitable for a wide range of watercraft including fiberglass fishing boats, ski boats, and jet skis. Easy InstallationFeaturing a strong pressure sensitive adhesives backing, this flexible strip allows for quick DIY installation, simply prepare the surface and put it on securely without any special tools. Essential ProtectionProtect your boats most vulnerable areas during docking or trailering with this must have aluminum , designed to prevent costly damage and extend the life of your watercraft.

What You Will Get You will receive 2 pieces of kayak keel guards in black and white, these keel guards are easy to use. You need to clean the surface firstly, then stick them on the keel. After sticking, please wait for over half an hour for the glue to be bonded, at last, you can use your boat in water confidently with keel guard for fiberglass boat. Reliable Material These keel guards are made of quality PVC material and the back is featured with marine glue, solid and sturdy, not easy to break, tear, deform or fade, can be applied for a long time, which makes keel guard for fiberglass boat more durable in all water environments.. Size Information Our keel guard for boat measures about 59.1 x 4 inches 1.5 x 0.1 meters, suitable for many different kinds of boats, you can adjust the size as you need, bringing you a pleasant using experience, and this proper dimension also lets keel guard for fiberglass boat fit most hulls perfectly. Practical Design This boat guard features delicate workmanship, is designed in a cone shape, can fit your boats better and prevent your boats from getting damaged by sands, rocks, concrete ramp and other hard things, offering you much convenience, greatly boosting the protective effect of keel guard for fiberglass boat. Wide Range of Application This keel guard is an ideal accessory for many boats, such as kayak, inflatable boats, fiberglass boats, aluminum boats and more.

2 Pcs Kayak Keel Guards you will receive 2 pieces of kayak keel guards in black, these keel guards are easy top use, you need to clean the surface firstly, then stick them on the keel, after sticking, please wait for over half an hour for the glue to be bonded, at last, you can use this keel in the water with confidence. Reliable Material these keel guards are made of quality PVC material and the back is featured with marine glue, solid and sturdy, not easy to break, tear, deform or fade, can be applied for a long time. Size Information our keel guard for boat measures about 59.1 x 4 inches 1.5 x 0.1 meters, suitable for many different kinds of boats, you can adjust the size as you need, bringing you a pleasant using experience. Practical Design this boat guard features delicate workmanship, is designed in a cone shape, can fit your boats better and prevent your boats from getting damaged by sands, rocks, concrete ramp and other hard things, offering you much convenience. Wide Range of Application this keel guard for fiberglass boat is an ideal accessory for many boats, such as, kayak, inflatable boats, fiberless boats, aluminum boats and more.

This Boat Skeg Repair Guard can cover and protect your skeg against damage from ramp dragging, reduce wear and tear from rocks, hidden debris, and submerged objects, also certainly can replace a broken skeg and keep boat balance. Skeg Guard Protector fits for Mercury for MerCruiser Stern Drive Bravo 1 3 1990-Present, not compatible with XR or Sport Models. Replace OE Number 27051. Strong Durable Material. Made of 18 Gauge Marine Grade 316 Stainless Steel with self-locking hardware and a mirror-polished finish. Comes with Male Female Stainless Locking Screws, 14-inch drill and hex key tools. Rational Considerate Engineering. Thickened 3mm lower wear tab reduces ramp dragging. Guard also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Easy Installation. Remain 2-3 Inches of Skeg firstly. Use a rubber mallet, slide the Guard onto the existing skeg and gently tap on it until fully seated. Then use the pre-drilled holes of the guard to drill skeg with a 14-inch drill bit supplied with the product, tighten the hardware with the hex key tool.

Ultimate Kayak Keel Guard Protection Our 6.5-foot keel guard is expertly designed for kayaks, offering robust defense against rocks, sand, and boat ramps. Ensure your kayak's keel stays protected from scratches and impacts during use with this easy-to-install guard that features strong adhesion and a perfect fit for most kayak models. Perfect for Aluminum Boats This durable keel guard is ideal for aluminum boats, providing reliable protection and corrosion resistance. With dimensions of 6.5ft long, 4.8 inches wide, and 0.24 inches thick, it offers full keel coverage to withstand harsh water conditions and significantly reduce wear and tear.. Ideal for Bass Boats Bass boat owners will appreciate this keel guard's superior impact absorption and durable construction. Its flexible design seamlessly conforms to your bass boat's keel without adding drag, ensuring smooth performance and long-lasting protection against underwater hazards. Comprehensive Boat Keel Guard Coverage Measuring a full 6.5 feet in length, this guard provides complete protection for various boat types. Crafted from high-density materials, it effectively absorbs shocks and prevents damage from rocks, concrete ramps, and other obstacles, safeguarding your investment.. Easy Installation for Your Kayak Featuring a strong self-adhesive backing, this keel guard for kayak ensures a secure and hassle-free installation process. Simply prepare the hull surface, apply the guard, and enjoy immediate, dependable protection against abrasions and scratches.

Stainless Steel Marine-Grade Protection Crafted from rust-resistant 316 stainless steel with a mirror polish, our boat keel guard delivers long-term durability in harsh marine environments. Resists chipping, corrosion, and UV damage.. Package Includes You will receive 2 pcs stainless steel boat keel guard protector with strong double-sided adhesive sticker, size 9 x 8.75 inches, Fits most fiberglassaluminum boatsno drilling or hull modification required.. Safe-Engineered Fit Features smooth, rounded edges and a semi-flexible design that contours perfectly to your hull. Protects without compromising structural integrity.. Hassle-Free Setup ? Clean surface Bend to shape Adhere firmly. No tools neededsaves hours vs. traditional methods.. Bow Protector The bow guard can be firmly fixed to your boat's keel, protecting your boat from scratches and wear from trailer rollers during loading and unloading and transportation and daily water wear and tear, saving a lot of expensive maintenance costs.. ? Note Not compatible with multi-curvedprotruding hull designs..

Maximum Hull Keel Protection Protect your Bonafide kayaks hull and keel from scratches, rocks, abrasion, and daily wear with the BerleyPro Bumper Bro keel protector. This durable marine-grade accessory shields your kayak during paddling, docking, trailering, and fishing adventures, keeping your hull in pristine condition.. Enhanced Stability Tracking By safeguarding the keel, the Bumper Bro maintains your kayaks natural tracking and stability. Paddle with improved control, reduced drag, and smoother performance on rivers, lakes, and coastal waters. Ideal for anglers, recreational paddlers, and touring enthusiasts.. Heavy-Duty Marine-Grade Construction Crafted from high-quality, impact-resistant marine materials, this keel guard withstands sun, water, and repeated contact with rocks or rough surfaces. Its robust construction resists flex, corrosion, and wear, ensuring long-lasting protection and dependable performance for all kayaking conditions.. Custom Fit for Bonafide Kayaks Specifically designed for Bonafide kayak models, the keel guard mounts securely along the hull without interfering with handles, tracks, or other accessories. Easy to install and stays firmly in place, providing consistent protection and maintaining optimal kayak performance.. Essential Kayak Accessory for Any Adventure Whether youre fishing, touring, or enjoying recreational paddling, the Bumper Bro keel protector is an essential accessory for Bonafide kayaks. Protect your investment, maintain hull integrity, and enhance your paddling experience for smoother, worry-free adventures on any waterway..

Superior Hull Keel Protection The BerleyPro Bumper Bro keel guard shields your NuCanoe kayaks hull and keel from rocks, scratches, and abrasion. Protect your kayak from damage while paddling, docking, or trailering, ensuring long-lasting durability and a pristine hull.. Maintains Tracking Stability By safeguarding the keel, this hull guard preserves your kayaks natural tracking and stability. Enjoy improved control, reduced drag, and smoother paddling in rivers, lakes, and coastal watersperfect for fishing, touring, or recreational use.. Marine-Grade Durable Construction Built from high-quality, impact-resistant, marine-grade materials, the Bumper Bro withstands repeated contact with rough surfaces, sun exposure, and water. It resists flex, corrosion, and wear, providing reliable protection on every kayaking adventure.. Precise Fit for NuCanoe Kayaks Specifically designed for NuCanoe kayaks, this keel guard mounts securely to the hull and keel without interfering with handles, tracks, or other accessories. Quick and reliable installation ensures your kayak stays protected and performance-ready.. Ideal for All Kayaking Adventures Whether youre an angler navigating shallow rivers, a recreational paddler exploring lakes, or a touring kayaker on new waterways, the Bumper Bro keel guard is essential. Protect your investment, enhance stability, and enjoy worry-free kayaking on every trip..

Maximum Hull Keel Protection The BerleyPro Bumper Bro keel guard protects your FeelFree kayaks hull and keel from scratches, rocks, abrasion, and daily wear. Keep your kayak looking new while reducing damage during paddling, docking, or trailering. Ideal for recreational paddling and kayak fishing.. Improved Tracking Stability This hull and keel protector preserves your kayaks natural tracking and stability. By safeguarding the bottom of your kayak, it reduces drag and ensures smoother paddling, improved control, and efficient maneuverability on rivers, lakes, and coastal waters.. Durable Marine-Grade Construction Built with impact-resistant, marine-grade materials, the Bumper Bro withstands sun exposure, water, and repeated contact with rocks and rough surfaces. Designed to resist flex, corrosion, and wear, it provides long-lasting protection and reliable performance for years.. Precise Fit for FeelFree Kayaks Designed specifically for FeelFree kayak models, this keel guard mounts securely along the hull and keel without interfering with handles, tracks, or other kayak accessories. Easy to install and stays in place, it ensures consistent protection and optimal performance.. Perfect for Every Kayaking Adventure Whether fishing, touring, or exploring, the BerleyPro Bumper Bro keel guard is ideal for all types of kayaking. Protect your investment, maintain hull integrity, and enjoy smoother paddling and improved stability every time you hit the water..

Superior Hull Protection for Wilderness Systems Kayaks Shield your kayak hull from scratches, scrapes, and abrasion with the BerleyPro Bumper Bro Keel Guard. Perfect for Wilderness Systems kayaks, this durable guard preserves the integrity of your kayak during launches, portages, and trailering, making it an essential kayak accessory.. Heavy-Duty Marine-Grade Construction Made from high-quality, flexible, and impact-resistant materials, this kayak keel guard ensures long-lasting protection against rocks, docks, and other obstacles. Ideal for fishing kayaks, sit-on-top kayaks, and canoes, it delivers durability without compromising performance.. Easy Installation Secure Fit The BerleyPro keel guard contours to the hull of Wilderness Systems kayaks for maximum coverage. Designed for a secure fit, it installs quickly without affecting paddling performance, kayak tracks, handles, or accessory mounts, ensuring protection without interfering with your gear.. Enhanced Performance for Kayaking Adventures Maintain smooth tracking and stability while protecting the kayak bottom. This keel guard pairs perfectly with other kayak accessories like rudder systems, cockpit covers, keel guards, and deck padding, enhancing overall comfort and performance on lakes, rivers, and coastal waters.. Perfect Upgrade for Kayak Enthusiasts Anglers Whether youre an angler, recreational paddler, or adventurer, this hull protection guard keeps your Wilderness Systems kayak in top condition. Combine with kayak storage solutions, paddling gear, and other accessories for a fully upgraded, protected, and high-performing watercraft setup..

Comprehensive Keel Protection You'll receive a 6ft length, 5in width black keel guard protector, which can effectively prevent keel scratches and wear. Designed to resist underwater obstacles such as gravel, sharp rocks, concrete ramps, and oyster beds. High-Strength Material The boat keel protector is made with a composite of high-density polyethylene HDPE and fiberglass-reinforced plastic FRP. Offers excellent hardness and toughness, can effectively absorb shocks and vibrations during navigation. Easy Installation Stable Bonding The keel guard for boats has a self-adhesive backing design. and equipped with tools such as gloves, sandpaper pads, and polishing tools. Easy and quick installation. Note the primer needs to be prepared separately to improve adhesion effectiveness. Flexible Fit The 5-inch wide thickened rubber protective pad fits the bottom keel perfectly. It does not drag the hull or increase navigation resistance after installation, maintaining a balance between protection and performance for optimal sailing. Widely Compatible Compatible with FRP boats and some aluminum boats, including recreational wakeboards, dinghies, light boats, jet boats, bass boats, wake boats, speedboats, aluminum fishing boats, and punts. It fits most micro-convex hulls and keel types.

Comprehensive Keel Protection You'll receive a 9ft length, 5ft width white keel guard protector, which can effectively prevent keel scratches and wear. Designed to resist underwater obstacles such as gravel, sharp rocks, concrete ramps, and oyster beds. High-Strength Material The boat keel protector is made with a composite of high-density polyethylene HDPE and fiberglass-reinforced plastic FRP. Offers excellent hardness and toughness, can effectively absorb shocks and vibrations during navigation. Easy Installation Stable Bonding The keel guard for boats has a self-adhesive backing design. and equipped with tools such as gloves, sandpaper pads, and polishing tools. Easy and quick installation. Note the primer needs to be prepared separately to improve adhesion effectiveness. Flexible Fit The 5-inch wide thickened rubber protective pad fits the bottom keel perfectly. It does not drag the hull or increase navigation resistance after installation, maintaining a balance between protection and performance for optimal sailing. Widely Compatible Compatible with FRP boats and some aluminum boats, including recreational wakeboards, dinghies, light boats, jet boats, bass boats, wake boats, speedboats, aluminum fishing boats, and punts. It fits most micro-convex hulls and keel types.

Boat Bow Guard The bow protector for boat can be tightly attached to your boat keel, protecting your boat from the wear and scratches of the trailer roller during loading, unloading and transportation, avoiding expensive maintenance costs.. Easy to Install First apply strong adhesive to the outer shell, dry the surface of the target location, then bend the boat bow protector to fit your hull, and peel off the adhesive back protective film, then attach it to the target location, and finally Peel off the thin film on the surface of the guard.. Durable Material Our bow guards for boats are made of stainless steel, mirror polished, not easy to rust, not easy to break, can effectively protect your boats for a long time.. Packaging Includes You will receive 2 pcs stainless steel boat keel guards, the size is 9 x 8.75 inch, which fits most boats and no more worries about damaging your boat bow.. Safe to Use Our bow protective guard fits your boat perfectly, it is polished, smooth edges, comfortable to touch, will not hurt your hands, and more beautiful..

Function ForoGore Boat Bow Guard design to protect your boat keel, prevent your boat from the trailer roller, rock Perfect Dimension, Suitable for many kinds of boats to use. Premium Material The Bow Guard for boat is made of stainless steel, Excellent Weather Rust Proof Performance. Sturdy and durable for long-lasting use. Product Size 9 x 8.85 inch Easy to bend design. Installation 1.Clean the surface of the boat keel 2.Pre-bend the guard to fit the surface shape of the boat 3.Peel off the protective adhesive film and stick to the target location tightly. Package Include Quality Guarantee 2 Pcs Stainless Steel Boat Keel Guard.

Product Size This kayak keel guard measures 3.3 yards in length and 3.9 inches in width. You are free to cut it according to your specific needs. Premium Material This kayak keel protective cover is made of rubber, which is durable and helps protect the hull from impact. Easy to Use Just peel off the red paper on the back and stick it directly onto the boat. You can also cut it to any shape or length as needed. Wide Applicaition Our kayak keel guard is universally compatible with most boat types, including kayaks, fiberglass, inflatables, and aluminum vessels. Warm Tips For best results, when using it, wipe the area with alcohol, press firmly during application, and allow 24 hours for full adhesion before use.

RELIABLE, LONG LASTING PROTECTION From rocks and concrete to ramps and docks, our keel guard is your boats first line of defense against damage Incredibly strong and durable, our hull guard helps protect against abrasions, scratches and scars.. VERSATILE DESIGN Whether you own a bass boat, a runabout or a recreational watercraft, our keel protector keeps your vessel in tip top shape Compatible with both fiberglass and most aluminum boats, it safeguards your precious investment.. DIY INSTALLATION Thanks to an exclusive 3M adhesion system, applying your keel guard is as easy as prep, peel, stick With no mixing or curing required, youll finish the job in an hour. The thickest marine adhesive around, it stays firmly in place.. MADE IN THE USA Combining the strength of pure Urethane Polymers with the quality of American workmanship, our protector kit is the one boaters trust Measuring 5 wide with lengths from 4 to 12 available in a range of colors, get a perfect match. LIFETIME GUARANTEE Were so confident in our boat keel guards, theyre backed with a limited lifetime guarantee against defects in materials or workmanship If you have any problems or questions, dont hesitate to let our customer service team know..

RELIABLE, LONG LASTING PROTECTION From rocks and concrete to ramps and docks, our keel guard is your boats first line of defense against damage Incredibly strong and durable, our hull guard helps protect against abrasions, scratches and scars.. VERSATILE DESIGN Whether you own a bass boat, a runabout or a recreational watercraft, our keel protector keeps your vessel in tip top shape Compatible with both fiberglass and most aluminum boats, it safeguards your precious investment.. DIY INSTALLATION Thanks to an exclusive 3M adhesion system, applying your keel guard is as easy as prep, peel, stick With no mixing or curing required, youll finish the job in an hour. The thickest marine adhesive around, it stays firmly in place.. MADE IN THE USA Combining the strength of pure Urethane Polymers with the quality of American workmanship, our protector kit is the one boaters trust Measuring 5 wide with lengths from 4 to 12 available in a range of colors, get a perfect match. LIFETIME GUARANTEE Were so confident in our boat keel guards, theyre backed with a limited lifetime guarantee against defects in materials or workmanship If you have any problems or questions, dont hesitate to let our customer service team know..

Applicable model - The kayak accessory and serves as an abrasion resistant for keel, bow, hull replacement accessory guard for your kayak. Designed for compatibility with most kayak models, including the compatible with Hobie 2019 Outback. It maintains structural integrity while allowing heat-adjustable customization for a seamless installation.. Easy Installation - The kayak keel guard is generally straightforward to install and takes the wear and tear instead of your kayak. This easy-to-install accessory ensures that your boat is protected quickly and efficiently. It's an essential kayak keel guard protector.. For Hobie Outback Kayak Accessories - Defend your kayak hull from boat launches, rocky shores, oyster beds, and abrasive surfaces with this rugged keel protector, engineered to prevent scratches, gouges, and impact damage while maintaining structural integrity through repeated hard-surface contact.. Kayak Hull Protector - The boat keel guard is made of high-density ABS material, offers outstanding durability and impact resistance. Its sleek design not only enhances the appearance of your kayak but also ensures it can handle the rigors of regular use, provides an additional layer of hull protection to your kayak.. For Hobie Parts - Each package includes 1 x Kayak Keel Guard. If you have any questions or concerns, please dont hesitate to reach out We will reply as soon as possible within 24 hours..

High Quality Durable Self-adhesive keel protector is made of thick and durable pvc material, which can effectively absorb the impact of collision and maximize the protection of your boat's keel 3M adhesive has been tested for waterproofing, which not only can fit the hull well but also is not easy to fall off. Compatible Boats Keel protection is available for fiberglass boats and some aluminum boats Fiberglass boats such as Bass Boats, Ranger Bass Boats, Ski Boats, Wake Boats, and Runabouts Aluminum boats mainly Fishing Boats and Jon Boats and can also be used for some recreational watercraft, Ski Boats, Skiffs, Dinghies, and most Jets. speedboats. Self-adhesive keel protection 5in wide, fits well on the keel protects your keel from gravel, sand, ramps, and oyster beds reduces damage to your boat when docking and reduces repair costs. Size selection Our keel protectors are available in three sizes, you can choose the right length according to the size of your boat 8FT is suitable for 22FT long boats, 9FT is suitable for 24FT long boats, 10FT is suitable for 26FT long boats. Installation steps You can read the instructions for specific precautions the installation is easy and concise the tape provided can be used to demarcate the boundaries mainly follow the following steps sanding, cleaning, priming not included, and applying.

Optimal Protection you will receive 2 keel protector measuring about 30 inches in length and from 4 inches to 2.5 inches in width, these keel guards provide extensive coverage Their design conforms seamlessly to your boat, safeguarding it from sand, rocks, concrete ramps, and other abrasive surfaces. Durable Protection for Your Boat our felt keel guard, crafted from fiber material, provides exceptional resistance to abrasion, heat, and tension Its durable design ensures long-lasting protection against harsh elements, keeping your boat safe. Convenient Installation equipped with a self-adhesive backing, our keel protector offers a simple, hassle-free application Just clean your hull surface, secure the felt, apply epoxy, and let it cool The keel guard has adhesive backing that helps with positioning, but additional glue needs to be applied for reinforcement Important Note Glue is not included in the package packing list you will need to prepare it separately.. Tapered Design for Optimal Fit the intelligently designed tapered shape ensures our keel protector conforms seamlessly to your boat's hull This precise fit enhances its protective capabilities, shielding your boat from potential damage. Fit for Various Boat Types whether you own a kayak, inflatable boat, fiberless boat, or aluminum boat, our keel guard is your versatile solution, offering extended coverage and protection for multiple areas of your boat.

Ultimate Keel Protection Our keel guard effectively shield your boat keel from abrasive sand, sharp rocks, concrete ramps, oyster beds, and other underwater obstacles, significantly reducing scrapes and wear and tear during daily use. Protect your keel from potential damage and save on future repair costs with our durable keel guards.. Wide Compatibility Our keel guard are designed for fiberglass boats Bass Boats, Ranger Bass Boat, Ski Boats, Wake Boats, Runabouts, some aluminum boats Fishing and Jon Boats, and recreational watercraft Ski Boats, Skiffs, Dinghies, and most Jet Boats. The guards can be applied on slightly raised strakes and chines with the included sealant for gap sealing.. Superior Craftsmanship Our keel guard for fiberglass boat are made from high-density polyethylene HDPE and fiberglass-reinforced plastics FRP, providing excellent hardness and durability. These materials effectively absorb shocks and impacts, offering maximum protection for your boat's keel. The rugged yet flexible design easily conforms to your boat's keel without adding drag.. STRONG ADHESION FOR EASY INSTALLATION Our keel guard for fiberglass boat feature strong self-adhesive 3M Marine Adhesive Sealant 5200 for a secure, tight fit. Simply follow these steps prepare hull surface, scribe, etch, clean, primer and attach. Buy with Confidence We stand behind our keel guards with a robust warranty and responsive customer service. If you have any issues or questions, our dedicated team is ready to assist you within 24 hours.. Buy with Confidence We stand behind our keel guards with a robust warranty and responsive customer service. If you have any issues or questions, our dedicated team is ready to assist you within 24 hours..

Reliable Keel Guards for Boats Our boat keel guard protect your boat keel from sand, rocks, concrete ramps, oyster beds, underwater objects and reduce scrapes, daily wear and tear on the water Our boat keel protector save the keel from any future possible damage for long lasting protection and save the cost of boat repairing form continuous shore landing. Compatibility Please MUST read the boat keel protector Product Description before purchase Keel guard for fiberglass boats Bass Boats, Ranger Bass Boat, Ski Boats, Wake Boats, Runabouts Keel guard for Some aluminum boats Fishing and Jon Boats Boat keel guard for Recreational watercraft Ski Boats, Skiffs, Dinghy and most Jet Boats The boat keel guard protector can be applied on slightly raised strakes and chines with applied sealant to seal off gaps. NOT FIT Our boat keel protector can NOT be bonded on LSE plastic that most Kayak or Canoe be made of NOT fit most Catamarans with sharp keels with a steep 90 upturn NOT fit boats that have raised or reinforced center keel that higher than 14 inch and build with reinforced welding around the edge, rivets or sharp angles. Premium Workmanship The keel protector for boats is produced from thick and durable Polymers materials that absorb the shocks and impacts with maximum protection on your boat keel The rugged and flexible 5 inch wide boat hull protector conforms to your boat's keel easily and won't drag your boat down. Easy to Install with Strong Adhesion The boat keel protector comes with strong self-adhesive 3M tape that provide firm and tight application Just stick keel guards on prepared hull surface, delimit, etch, clean, prime and apply. Size Guide The 7 foot Keel Guard fit boat size up to 20 ft It is recommended that apply the keelguard keel protector beyond the lowest point of the boat which protect your boat from snagging and tearing when beaching or loading The length of boat keel protection can be extended, but not shorten it. Warm Tips Please repair any damage and keep the surface of shield keel guards for boats in good state before application Please install the keel guard 4-6 inches ABOVE the resting water line to avoid the keel guard peel off the hull Please do NOT touch lean against anything such as v-blocks, bunks, rollers, or bow stops for best adhesion of 3M adhesive.

Product specifications Length 6.4 inches Width 4.84 inches Thickness 0.24 inches. Keel Guard Compatible Always read product description before purchase Keel Protector for Fiberglass Boats Bass Boats, Ranger Bass Boats, Ski Boats, Wake Boats, Speedboats Keel Protector for Some Aluminum Boats Fishing Boats and Jon Boats Keel Protector for Recreational Watercraft Ski Boats, Dinghies, Skiffs and Most Jet Boats Guards can be applied to slightly raised gunwale and keel, and gap sealed with included sealant.. Keel Guard Easy to Install Boat Keel Protector comes with strong self-adhesive 3M tape for a secure and tight fit Simply stick the keel guard to the prepared hull surface, delineate, etch, clean, prime and apply, Note Keel Primer is not included in the kit.. Keel Guard Premium Craftsmanship Our fiberglass boat keel guard is made of high-density polyethylene HDPE and fiberglass reinforced plastic FRP for excellent hardness and durability. These materials effectively absorb shocks and impacts, providing maximum protection for your boat's keel. The strong yet flexible design easily fits your boat's keel without adding drag.. Keel Guard Premium Not Applicable Our boat keel protector cannot be bonded to the LSE plastic used in most kayaks or canoes not suitable for most catamarans with sharp keels with steep 90 upturns not suitable for boats with raised or reinforced center keels higher than 14 inch, and reinforced welds around edges, rivets or sharp corners.

Product specifications Length 6.4 inches Width 4.84 inches Thickness 0.24 inches. Keel Guard Compatible Always read product description before purchase Keel Protector for Fiberglass Boats Bass Boats, Ranger Bass Boats, Ski Boats, Wake Boats, Speedboats Keel Protector for Some Aluminum Boats Fishing Boats and Jon Boats Keel Protector for Recreational Watercraft Ski Boats, Dinghies, Skiffs and Most Jet Boats Guards can be applied to slightly raised gunwale and keel, and gap sealed with included sealant.. Keel Guard Easy to Install Boat Keel Protector comes with strong self-adhesive 3M tape for a secure and tight fit Simply stick the keel guard to the prepared hull surface, delineate, etch, clean, prime and apply, Note Keel Primer is not included in the kit.. Keel Guard Premium Craftsmanship Our fiberglass boat keel guard is made of high-density polyethylene HDPE and fiberglass reinforced plastic FRP for excellent hardness and durability. These materials effectively absorb shocks and impacts, providing maximum protection for your boat's keel. The strong yet flexible design easily fits your boat's keel without adding drag.. Keel Guard Premium Not Applicable Our boat keel protector cannot be bonded to the LSE plastic used in most kayaks or canoes not suitable for most catamarans with sharp keels with steep 90 upturns not suitable for boats with raised or reinforced center keels higher than 14 inch, and reinforced welds around edges, rivets or sharp corners.

Expert Advice Available we are here to answer your questions.. Megaware KeelGuard - 8 - Red 20808. MSRP 194.95, Mfg Part Number 20808. Return shipping for damageddefective items will be covered by the seller.. Authorized Dealer.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. Designed for Specific Motors SkegGuard 27071 FITS Honda 60BFP Power Thrust 2010-Present, 75-90hp 4 stroke 4 cyl 1995-Present, 100hp 4 stroke 4 cyl 2007-Present, 115hp 4 stroke 1999-2010. FORCE 70-90hp 2 stroke by Mercury 1998-2002. MERCURY MARINER 40-50-60hp 4 stroke Big Foot, Command Thrust, Sea Pro 4.25 2001-Present, 75-90-115hp 2 4 stroke 1984-2014, 125hp 2 stroke 2000-2012. NISSAN TOHATSU 70-75-90-115-120-140hp 2 stroke 1993-2018, 75-90hp BFT 4 stroke 2014-2019.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. Designed for Specific Motors SkegGuard 27151 for Yamaha 150-175HP 2 4 Stroke 1984-Present, 200HP 2 Stroke No VVX 1984-2006, 200HP 4 Stroke I-4 2012-Present, 300HP 4 Stroke 2007-2009, 350HP 4 stroke 2007-2019. For 350HP year 2023 See Megaware SkegGuard 27301.

Skeg Guard Protector - Add an extra layer of protection to your skeg against ramp dragging, damage from hidden debris, and everyday wear and tear on the water with the SkegGuard from Megaware - also great for replacing a broken skeg. Easy to Install - The skeg protector features a 3mm lower wear tab and is easy to install in just 4 simple steps in under 10 minutes using a rubber mallet, slide the SkegGuard onto the existing skeg and gently tap on it until fully seated use the pre-drilled holes to drill skeg using a 14-inch drill bit. Superior Engineering - Our skeg protector is made from heavy-duty 18 gauge marine grade 316 stainless steel with a mirror-polished finish and easily conforms to your skeg it also features a drain hole on the bottom to prevent water from collecting and causing corrosion or freezing. Installation - You can attachinstall the SkegGuard with as little as 2 to 3 inches of the original skeg remaining comes with a 3-year warranty. SkegGuard 27321 FITS Yamaha 50-60hp 4 Stroke High Thrust 2003-Present, 60hp 2 stroke 2002-2005, 70hp 2 4 stroke 2002-Present, 75hp 4 stroke 2003-2017, 90hp 2 4 stroke 2002-2016.

Skeg Protector - Reduce wear and tear while protecting your skeg against damage from ramp dragging, rocks, debris, and submerged objects with the Megaware SkegPro - the makers of the original KeelGuard. Proper Protection - Our guard helps prevent corrosion and freezing on your skeg it also features a drain hole at the bottom to prevent water from collecting to ensure your boat doesn't become stagnant. Strong and Reliable - The skeg cover is made from 18 gauge marine grade 304 stainless steel with self-locking hardware and a mirror-polished finish. The easy do-it-yourself application ensures you'll have your SkegPro installed in less than 10 minutes. FITS Yamaha 75-90hp 4 Stroke 2017-Present 115-130hp 2 4 Stroke 1994-Present No PB Series 150-175hp 24 Stroke 1984-Present 200hp 2 stroke HPDI VMAX HPDI 2000-2012 200hp 4 Stroke 2.8L I-4 2012-Present 300 4 Stroke 2007-2009 350hp 5.3L V8 2007-2019 IO Sterndrive Models 1989-1993. A Commitment to Excellence - Megaware KeelGuard is a family-owned business that revolutionized the keel protection industry with its patented, do-it-yourself keel protector in 1992. We offer a range of high-quality products to keep innovating and providing top-notch support for your investment..

Pontoon Protector - Protect vulnerable and exposed areas of your pontoon against unsightly dents and scrapes with Megaware Keelguard Pontoon Guard - comes in 4 colors Blue, Red, Gray, and Black and is UV-stabilized. Solid and Durable - The pontoon docking guard is made from strong 14-inch thick ultra-tough polymer composite for maximum durability. It also features a wide machine-contoured leading edge and contoured sides for a clean, sleek, and tight seal. Increases Visibility and Safety - The boat tube protector features a 3M reflective strip to make your vessel more visible during night operations or while anchored or beached when illuminated by headlights or searchlights. Two Lengths for Double the Options - Our boat dock bumper guards come in 2 lengths to ensure you find the right fit for your pontoon. Our sizes include a 32 feet kit - 2 16 feet lengths for pontoons up to 21 feet, and a 40 feet kit - 2 20 feet lengths for pontoons 2225 feet. 3-Year Warranty - The Megaware KeelGuard Pontoon Guard is so tough and reliable that we include a 3-year warranty during regular use of your boat for as long as you own your vessel.

Easy to Install - The boat protector features an exclusive self-sealing contoured edge that creates a clean, tight seal no messy sealants needed. Easy install in 4 simple steps etch, clean, prime, apply. Superior Engineering - This patented hydrodynamic drag reduction design is produced using the highest quality materials and 3M premium adhesives. Pliable and tough, the 5-inch wide boat keel protection easily conforms to your boat's keel its shock absorbing, exclusive contoured edge design, and drag reduction channels won't slow your boat down. 9 Standard Length Kits - Our boat keel guard comes in 9 different sizes that range from 4 to 12 feet long to ensure you have the correct size shields come in 12 colors that will not fade or dull while enhancing the look of your boat. Note if the size of your boat falls between 2 sizes, order a size up for additional keel protection. Lifetime Warranty - The Megaware KeelGuard is so tough and reliable that we include a lifetime warranty during normal use of your boat, for as long as you own your boat..

Ultimate Keel Protection for Your BoatShield your hull from rocks, oyster beds, sand, and concrete ramps with our high-density, wear-resistant keel guard. Say goodbye to scratches and costly repairsprotect your boat every time you hit the water. Fits Fiberglass, Aluminum MoreDesigned for bass boats, ski boats, wake boats, jon boats, dinghies, and most jet boats. Easily fits slightly raised keels and strakes, sealing gaps with included marine-grade adhesive for a perfect, secure fit.. Shock-Absorbing, Low-Drag DesignMade of thick, durable rubber, our keel protector absorbs impacts while maintaining smooth hull performance. Resistant to saltwater, scratches, and harsh marine environmentsstrong, flexible, and built to last.. Quick Easy DIY InstallationIndustrial-strength Marine Adhesive Sealant 5200 ensures a secure hold. No special tools neededsimply clean, prime, and attach. Perfect for boat owners to install themselves and save on professional costs.. Reliable Warranty 247 SupportBuy with confidence Our keel guard comes with a robust warranty and responsive customer service. Protect your boat today and enjoy peace of mind with long-lasting, hassle-free hull protection..

Ultimate Kayak Keel Guard Protection Our 6.5-foot keel guard is expertly designed for kayaks, offering robust defense against rocks, sand, and boat ramps. Ensure your kayak's keel stays protected from scratches and impacts during use with this easy-to-install guard that features strong adhesion and a perfect fit for most kayak models. Perfect for Aluminum Boats This durable keel guard is ideal for aluminum boats, providing reliable protection and corrosion resistance. With dimensions of 6.5ft long, 4.8 inches wide, and 0.24 inches thick, it offers full keel coverage to withstand harsh water conditions and significantly reduce wear and tear.. Ideal for Bass Boats Bass boat owners will appreciate this keel guard's superior impact absorption and durable construction. Its flexible design seamlessly conforms to your bass boat's keel without adding drag, ensuring smooth performance and long-lasting protection against underwater hazards. Comprehensive Boat Keel Guard Coverage Measuring a full 6.5 feet in length, this guard provides complete protection for various boat types. Crafted from high-density materials, it effectively absorbs shocks and prevents damage from rocks, concrete ramps, and other obstacles, safeguarding your investment.. Easy Installation for Your Kayak Featuring a strong self-adhesive backing, this keel guard for kayak ensures a secure and hassle-free installation process. Simply prepare the hull surface, apply the guard, and enjoy immediate, dependable protection against abrasions and scratches.

Great Compatibility 27341 SkegGuard kit is perfectly compatible with Evinrude Johnson 40 - 50 hp 4 Stroke 1999-2003, Mercury Mariner 40 hp 50 hp 60 hp 2 4 Stroke 2003-Present. Also available for many selected inboardoutboard engines such as Evinrude, Johnson, Force, Honda, Mercury, Mariner, Nissan, Tohatsu, OMC, Suzuki, Volvo and Yamaha engines. Replace OE Part Number 27341. Skeg Guard Broken Skeg Fixer Indispensable SkegGuard not only protects motors skeg from damage, also quickly fixes broken skeg with as little as 2-3 inches of skeg remaining. Meanwhile, perfect design with drain hole in the bottom to prevent water from collecting and stagnating, causing corrosion. Matches your lower unit to ensure no discernible drag or compromise in performance.. Built for Marine Environment Keel Guard Constructed of high quality marine-grade 316 stainless steel material with an extra reinforced 3mm lower wear tab across the bottom. Protect against ramp dragging or damage from hidden debris. Corrosion resistance and resist damage. Stable, reliable and long-lasting durability.. Easy to Install It takes a breeze to install. Simply slide and match the skeg guard to the skeg. Use mallet for proper fit. Drill through with 14 holes. Install hardwares with hex wrenches provided. Then, youre ready to go. Comes with stainless steel self locking hardware and hex wrenches. Please make sure the model fits well with the skeg on your motor before purchase.. 100 Satisfaction Guarantee Your satisfaction is our priority. We strive to give our customers excellent service. All Sixcow products support 30-Day money-back guarantee, 12-Month warranty for quality-related issues. Simply return it for your warranty..

Complete Boat Keel Protection Kit the package includes 2 stainless steel bow guards, 118 x 4.72 inch boat keel protector, gloves, sandpaper, and smoother With all these accessories, you can easily complete the boat body protection installation. Size The bow guards measure 9 x 8.75 inches, the DIY keel protector is 118 inch long and 12cm4.72 wide. These sizes are suitable for the bow and keel dimensions of most boats. Moreover, you can make some adjustments according to your specific needs for a better fit. Fit Design The keel protector for fiberglass boats device features a grooved design that fits the contour of the boat's bow precisely. The PVC friction strip has a drag - reducing grooved edge, which does not affect the boat's speed. Both are designed to fit most bass boats and fishing boats. Fit Design The keel guard device features a grooved design that fits the contour of the boat's bow precisely. The PVC friction strip has a drag - reducing grooved edge, which does not affect the boat's speed. Both are designed to fit most bass boats and fishing boats. Versatile Application This boat keel protection kit is suitable for various small boats such as bass boats and fishing boats. It can protect the bow and keel from scratches and impacts caused by rocks, sandy beaches, concrete ramps, and underwater objects, making it a practical equipment for daily boat protection and damage prevention.

SizeTotal length 10ft 3 meters per roll Width 4.7212cm. Material the boat keel protector is made of thick and durable PVC material, which can absorb the impact and maximize the protection of your boat's keel. The 4.7212cm wide hull protector is rugged and resilient and fits easily over the keel of the boat without dragging the boat down. ForKeel guards protect your boat's keel from sand, rocks, concrete ramps, oyster beds and underwater objects, reducing scratches and everyday wear and tear on the water. Package 10ft PVC boat keel protector with self-adhesive 3M-tape Warm tips keel primer was not included in the kit..

Product specifications Length 6.4 inches Width 4.84 inches Thickness 0.24 inches. Keel Guard Compatible Always read product description before purchase Keel Protector for Fiberglass Boats Bass Boats, Ranger Bass Boats, Ski Boats, Wake Boats, Speedboats Keel Protector for Some Aluminum Boats Fishing Boats and Jon Boats Keel Protector for Recreational Watercraft Ski Boats, Dinghies, Skiffs and Most Jet Boats Guards can be applied to slightly raised gunwale and keel, and gap sealed with included sealant.. Keel Guard Easy to Install Boat Keel Protector comes with strong self-adhesive 3M tape for a secure and tight fit Simply stick the keel guard to the prepared hull surface, delineate, etch, clean, prime and apply, Note Keel Primer is not included in the kit.. Keel Guard Premium Craftsmanship Our fiberglass boat keel guard is made of high-density polyethylene HDPE and fiberglass reinforced plastic FRP for excellent hardness and durability. These materials effectively absorb shocks and impacts, providing maximum protection for your boat's keel. The strong yet flexible design easily fits your boat's keel without adding drag.. Keel Guard Premium Not Applicable Our boat keel protector cannot be bonded to the LSE plastic used in most kayaks or canoes not suitable for most catamarans with sharp keels with steep 90 upturns not suitable for boats with raised or reinforced center keels higher than 14 inch, and reinforced welds around edges, rivets or sharp corners.

RELIABLE, LONG LASTING PROTECTION From rocks and concrete to ramps and docks, our keel guard is your boats first line of defense against damage Incredibly strong and durable, our hull guard helps protect against abrasions, scratches and scars.. VERSATILE DESIGN Whether you own a bass boat, a runabout or a recreational watercraft, our keel protector keeps your vessel in tip top shape Compatible with both fiberglass and most aluminum boats, it safeguards your precious investment.. DIY INSTALLATION Thanks to an exclusive 3M adhesion system, applying your keel guard is as easy as prep, peel, stick With no mixing or curing required, youll finish the job in an hour. The thickest marine adhesive around, it stays firmly in place.. MADE IN THE USA Combining the strength of pure Urethane Polymers with the quality of American workmanship, our protector kit is the one boaters trust Measuring 5 wide with lengths from 4 to 12 available in a range of colors, get a perfect match. LIFETIME GUARANTEE Were so confident in our boat keel guards, theyre backed with a limited lifetime guarantee against defects in materials or workmanship If you have any problems or questions, dont hesitate to let our customer service team know..

KeelShield is easy to install. just Prep-Peel-Stick. Once its on you are good to go. Installation does not require time to cure.