Don't Let Your Expensive Engine To Fall Off The Stand And Get Damaged. Compatible With All Chevy Small and Big Block, LS LT Engines. Made in Wichita, Kansas From 6061-T6, USA Produced Billet Aluminum. Keeps Your Engine Secured To The Stand. Allows The Use Of A Flywheel Or Flexplate.

Compatible with all Gen 2, 3, 4, and 5 LS and LT engines and ignition coils. 8pcs of 5 foot length plug wires. Made in the USA. Spiral core wire, 350 ohm, with 8mm thick jacket. Package includes 8 plug wires, 8pcs 135 degree boots and terminals, 8pcs 90 degree boots and terminals, 8pcs straight boots and terminals.

Compatible with LSA, LS9, and LT4 superchargers. Can be used to plug 1 or both MAP sensor port locations. Billet plug securely seals MAP sensor bores. Includes 1 plug, with FKM oring, and USA made bolt. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum.

These brackets move your coils down toward the center of the valve cover from factory coil location.. These brackets are designed to fit D581 coils, and move them 1-18 down toward center of the valve cover from factory coil location.. These will also work with D510C or D514A coils if you get the spacer kit 551303, and will move them 1-38 down toward center of the valve cover from factory coil location.. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Included in the package are 2 coil brackets, and required mounting hardware..

This bracket will replace your factory coil bracket and is sure to dress up your LS engine and securely mount your ignition coils on your valve covers, similar to the factory arrangement. These brackets will only fit the Heat Sink style coils, also referred to as the D585. Other brackets are available to fit all other LS ignition coils. see photo coil guide. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. This kit will come with all mounting brackets and American-made hardware to mount all 8 coils on two valve covers. These brackets come in a satin aluminum finish for durability and corrosion resistance.

Conveniently add a 18 NPT port into your top radiator hose to feed your cylinder head crossover tube to. Compatible with 1-14 upper radiator hoses factory LS vehicle size. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Machined aluminum finish. Package Includes 1 hose barb coupler.

Take out all the guess work and have an adapter for any situation when swapping an LS engine.. This is a master set to adapt any SBCBBC and aftermarket sensors to fit into all LS series engines.. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Included in this package is 6 different adapter fittings for oil pressure or coolant temperature sensors.. Check out the ICT Billet store for more LS Swap Solutions..

This bracket mounts the alternator in front of the passenger side head.. This bracket will work with serpentine and V-belt pulleys.. You will need to make sure that your cylinder head has 38 threaded holes, same as the water pump. Some cylinder heads have 1116 threaded holes.. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Included in the package is 2 brackets, 1 turnbuckle tensioner, and required mounting hardware..

Build your own custom -AN transmission lines with these -6AN fittings. Compatible with GM transmission case holes, up to 2007. Compatible with TH350, TH400, 4L60E, 700R4, 200-4R, TR6060, Ford AOD 4R100, 4R70W, and C5 transmissions. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Includes 2 fittings and orings.

Designed for the Front short fitting and rear long fitting transmission line ports, -6AN to 14NPSM. thread O.D. .516, standard GM transmission case thread. These fittings are threaded into the cooler ports in your transmission and enable you to run AN lines to a transmission cooler.. This fitting kit compatible with 4L80E transmissions.. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum.. Package Includes 1 front fitting,1 rear fitting both are bare aluminum finish, and 2 O-Rings..

This bracket provides the missing bolt hole on the LS engine block that is used on SBCBBC engines to bolt the dipstick tube to the cylinder head. Compatible with TH400, TH350, 4L60E, 700R4, 2004R, 4L80E Transmissions. Made in the Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Included in the package is 1 adapter bracket, and 2 bolts. LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77.

Grade 10.9 bolts. Heavy duty, high strength. Zinc coated for long lasting corrosion protection and prevents threads from seizing. No washers needed with these flanged headed JIS spec bolts. Metric Flange Bolts.

Adapts Powerglide, 4L80E, TH400, TH350, 700R4, 4L60, 4L60E from non LS engine torque converter snout to LSLT engine. See our LSLT Crankshaft and Flexplate guide to determine where to place your crankshaft hub adapter. Made in Wichita, Kansas from USA produced steel. Compatible with all LS and LT series engines Gen 3, 4, 5 except 99-00' 6.0L does not require this. Includes 1 adapter ring inserts into rear of crankshaft.

Grade 10.9 bolts. Heavy duty, high strength. Zinc coated for long lasting corrosion protection and prevents threads from seizing. No washers needed with these flanged headed JIS spec bolts. Metric flange bolts.

Compatible with 1998-02 LS1 Camaro water pump conversions to LS Truck engine to keep the belt aligned with truck accessories. Compatible with all LS engines. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Adapt a LS1 water pump with a forward facing radiator hose outlet to your truck engine. Includes 2 spacers, 4 gaskets, 1 steam port plug 18, and bolts.

This kit uses TruckSUV or LS3L99 Camaro crank pulley. Includes bracket, idler pulley, tensioner, and mounting hardware. Can be used with standard 105amp or high amp 145160amp LS style alternators. will not fit CorvetteCTSV or 2010-15 Camaro large bolt pattern alternators. Designed to be paired with a 551779-3 AC compressor and power steering pump bracket kit. Compatible with 965K6 belt when used with 551779-3 bracket kit. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. This kit uses USA made belt tensioner, flange bolts, spacers, brackets.

This plate allows the factory LS sending unit to be moved to the side of the oil pan. Compatible with LS series GM V8 engines EXCEPT GTO front sump oil pans and LS4 oil pans. M16-1.5 threaded port. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Included in the package is 1 adapter, 1 o-ring, required mounting hardware.

Made In Wichita, Kansas From Aerospace Grade, USA Billet Aluminum. This Kit Requires The Use Of A Corvette Or CTSVG8SS Crank Pulley 12560115 ICT Billet BAL100. Compatible With Chevy Corvette G8 SS CTS-V Z06 LS1 LS2 LS3 LS6 LS7 L77 5.7L 6.0L 6.2L 7.0L Gen III IV 1997-2013 Series Engines. Included in the package is the alternator, power steering bracket, 1 smooth pulley, and all required mounting hardware.. This Kit Will Place The Alternator Power Steering Pump In The Factory Corvette Location..

Compatible with Corvette Or CTSVG8SS Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Compatible with all GM LS series engines. Includes brackets and mounting hardware. Billet Alternator Bracket Low Mount.

1.25 hose barb to 1.5 barb reducer with a hose stop flange to keep the coupler centered in the splice connection. Commonly used to couple or repair your radiator hose, brake booster hose, vacuum line, or any other hoses together. Machined aluminum finish. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Package includes 1 coupler.

Factory LS cylinder heads are machined with metric M12-1.5 coolant sensor ports, so your factory Small Block Chevy sensor won't thread in to them. This adapter allows you to keep your original sensors and integrate them into your swapped LS engine.. Adapter has a female 38 NPT port, .85 deep. Refer to thread chart to check your correct fitting size.. Made in Wichita, KS from aerospace grade, USA billet aluminum. This adapter will fit all LS series engines.. Adapters are sold individually, and include 1 sealing washer.

R4 AC Compressor Heavy Duty Bracket Kit. Compatible With truckSUV or LS3L99 Camaro crank pulley. Kit uses USA Made belt tensioner, bolts, pulley, and bracket. Made in Wichita Kansas from Aerospace Grade USA Billet Aluminum. Includes bracket, belt tensioner, and mounting hardware.

Made with OEM specifications for the best possible fitment into your vehicle. These plates will move the crankshaft centerline up .17 in the vehicle. Made in Wichita, Kansas from aerospace grade, USA produced, 38 billet aluminum. Includes 2 adapter plates, 8 flat head bolts, and 6 flange M10-1.5 bolts plates are M10 threaded, use the hardware included. Natural aluminum finish.

Made From 14 Thick, Hardened Aluminum. Solid Mount Your Race Engine For Quicker E.T.'s. Made In Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Make Installation a Breeze By Using 2 Pieces Of Cardboard, Cut Each Side For Vehicle, Then Tape the 2 Pieces Together And Lay On Top Of The Engine Plate As A Template. 12 Tall x 36 Wide, Compatible with Most Applications.

Made From 14 Thick, Hardened Aluminum. Solid Mount Your Race Engine For Quicker E.T.'s. Made In Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Make Installation a Breeze By Using 2 Pieces Of Cardboard, Cut Each Side For Vehicle, Then Tape the 2 Pieces Together And Lay On Top Of The Engine Plate As A Template. 12 Tall x 36 Wide, Compatible with Most Applications.

Conveniently add a 18 NPT oil supply for your turbocharger. Compatible with all LS oil pans except dry or front sump. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Heavy duty, 12 thick billet aluminum plate for maximum oil circulation. Includes re-usable oring seal and mounting hardware.

This plate is used to seal off the oil port in your oil pan above the oil filter while also offering two2 18-2NPT ports straight up or straight down, for sensors or turbo oil feed line. This plate compatible with all LS oil pans, except GTO front-sump oil pans, dry-sump oil pans LS7, LS9, etc, and LS4 oil pans. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Machined out of 1 thick billet aluminum. Includes one adapter plate, one reusable o-ring seal, 2 - 18 pipe plugs, and mounting bolts.

Grade 10.9 Bolts. Heavy Duty, High Strength Bolts. Zinc Coated For Long Lasting Corrosion Protection and Prevents Threads From Seizing. Compatible with Any 97-14 GM LS Series Engine Oil Pan. Metric Flange Bolts.

-6AN Oil cooler feed and return block. Features 2 -6AN ORB threaded holes. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Includes re-usable oring seals and mounting bolts. LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77.

Compatible with SBC engines with long water pump. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. For use with Sanded 508 V-belt pulley AC compressor. This kit works with 3-rib V-belt pulleys. Includes brackets, instructions, and mounting hardware.

Assembled with OEM tooling, OEM connector, lock, seals, and terminals,uses OEM harness wire colors for a perfect fit. Assembled in Wichita, Kansas with USA made OEM grade TXL wire. Adapt Your Factory Wire Harness With ICT Billet Wire Extension Harnesses To Accept Different Sensor Connector Styles. Includes 1 Wire Harness Adapter. Highest Quality Wire Connectors On The Market, For the Most Dependable, Longest Lasting Connections.

Low mount alternator bracket and head mounted power steering bracket. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Compatible with any LS series engine block and heads. Mounts the alternator and power steering in 4th gen LS1 original location. Includes 2 brackets.

Compatible with 1998-02 Camaro LS1 GTO Any Year Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Compatible with all GM LS series engines. Compatible with 1998-02 LS1 Camaro power steering pump pulley. Package Includes mounting bracket and mounting hardware.

Made In Wichita, Kansas From Aerospace Grade, USA Billet Aluminum. This Kit Requires The Use Of A 98-02 Camaro Crank Pulley ICT Billet. Compatible with 1998 1999 2000 2001 2002 Chevy Camaro Z28 SS Pontiac Firebird Formula Trans Am WS6 GT0 LS1 LS6 5.7L 6.0L Gen III Series Engines. Included in the package is the alternator, power steering bracket, 1 smooth pulley, and all required mounting hardware.. This Kit Will Place The Alternator Power Steering Pump In The Factory Corvette Location..

Compatible with Gen 4 LS Engines. Compatible with all years factory LS oil pressure sensors. Includes Adapter Bolts and Oring. M16-1.5 thread. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum.

Compatible with all GM LS series engines. Passenger side port adapter has two 18npt ports, drivers side port adapter has one 18npt port. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Can be installed on the front or rear of the cylinder heads. 18 NPT threaded ports.

Commonly Used for fabricating custom radiator, thermostat housings, or heat exchanger connections.. 37 degree flare fitting automotive standard. Machined aluminum finish. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. See thread chart photo in this listing to identify your fitting size.

Most LS oil pickups are secured to the oil pump using only 1 bolt on one side of the flange. This girdle straddles the flange and secures the pickup tube to the oil pump with 2 bolts for maximum clamping capacity.. Compatible with all LS series engines 1997-2014. Made in the Wichita, KS from aerospace grade, USA billet aluminum. Will not work with pick up tube with flange retainer tab see photo. Sold individually, includes 2 new bolts.

Used for relocating the alternator and power steering pump close to the engine centerline to clear turbo headers. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. This kit includes USA made metric flange bolts, belt tensioner, and idler pulleys. Compatible with truckSUV or LS3L99 Camaro crank pulley ICT BAL300. Compatible with LS1 '98-'02 Camaro power steering pump pulley ICT PUM200 and PUL200 Truck any year Alternator ICT ALT300will not fit CorvetteCTSV, SS, G8 or 2010-15 Camaro large bolt pattern alternators, or 160 amp LS truck alternators LS1 '98-'02 Camaro water pump WAT200 this kit includes water pump spacers and LS3L99 Camaro water pump WAT302-spacers not needed Bracket kit not compatible with any other water pump.. LS1 '98-'02 Camaro power steering pump pulley ICT PUM200 and PUL200. Truck any year Alternator ICT ALT300will not fit CorvetteCTSV, SS, G8 or 2010-15 Camaro large bolt pattern alternators, or 160 amp LS truck alternators. LS1 '98-'02 Camaro water pump WAT200 this kit includes water pump spacers and LS3L99 Camaro water pump WAT302-spacers not needed. Bracket kit not compatible with any other water pump.. Fits all LS series engines. Includes mounting brackets, tensioner, idlers pulleys, and all mounting hardware. Not compatible with low mount 4-rib AC compressor on passenger side. Please see ICT 551137-LS76-3 for our compatible low mount 6-rib AC option. Please see ICT 551137-LS76-3 for our compatible low mount 6-rib AC option. If using Camaro Intake Manifold and Throttle Body you may need a throttle body rotation adapter 551781 when using with LS3. If needing to extend your alternator harness connection, use ICT WEALT30-36 4-pin or WEALT40-36 2-pin. This kit is made with part 's 551587-LS01-3, 551581-3, and 551527-LS01-3 bracket kits.

Fits with truckSUV or LS3L99 Camaro crank pulley ICT BAL300. Fits with TruckSUV any year power steering pump pulley ICT PUM300 and PUL300. Fits with Truck any year Alternator ICT ALT300 excludes CorvetteCTSV large bolt pattern alternators, or 160 amp LS truck alternators. Suitable for all LS series engines. Manufactured in Wichita, Kansas using aerospace grade, USA produced, billet aluminum. Includes part 551321-3 and 551799-3 bracket kits, and 551690-71 water pump spacers. Belt length with 105amp alternator 68.0 680K6.

Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Compatible with all gen III engine blocks. Includes stainless steel bolts. Includes gasket.

This fits with ALL transmissions installed does not require trans removal. Use when installingremoving balancer, flywheel, torque converter, and many other parts or bolts. Made in Wichita Kansas from heavy duty, aerospace grade, USA produced billet aluminum. This package includes 1 holding tool, 2 mounting bolts.. Mounts to starter bolt flange.

This fitting has a 34 barb on both sides of the fitting with a hose stop flange to keep the coupler centered in the splice connection.. Commonly used to couple or repair your radiator hose, brake booster hose, vacuum line, or any other hoses together.. Machined aluminum finish. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Package includes 1 coupler.

Used to plug the oil galley when the vacuum pump is removed from the engine block. Compatible with ALL Gen V, 2014 newer LT series engines LT1 LT2 L82 L83 L84 L86 L87 L8B LT4 LT5 LV3. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Compatible with ICT Billet LS Swap adapter plate 551363X. Oringed for leak free seal no gasket required.

Use this to make your own custom power steering lines.. 37 degree flare fitting automotive standard. Machined aluminum finish. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. See thread chart photo in this listing to identify your fitting size.

This throttle body adapter will allow you to install a 3-bolt DBC LS throttle body onto a 4-bolt LS intake. For example, an LS2 or LS3 intake manifold.. Compatible with up to 75mm Throttle Body. Compatible with intake manifolds up to 92mm. Does not work with 3-bolt drive by wire throttle body or LS4 intakes. Natural finish aluminum as shown, includes mounting hardware and gasket.

This throttle body adapter will allow you to install a 3-bolt DBW LS throttle body onto a 4-bolt LS intake. For example, an LS2 or LS3 intake manifold.. Compatible with up to 75mm throttle body. Compatible with intake manifolds up to 102mm. Does not work with 3-bolt drive by cable throttle body or LS4 intakes. Natural finish aluminum as shown, includes mounting hardware and gasket.

Dress up your engine with this great looking billet aluminum valley cover. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Compatible with Gen IV Engine Blocks LS2 LS7 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77. Machined aluminum finish. Includes stainless steel bolts.

Compatible With Truck SUV or LS3 L99 Camaro Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Compatible with a Saginaw Type 1 power steering pump. Compatible with any LS Powered Vehicle Alternators with any Amperage. Includes Brackets idler pulley and Mounting Hardware.

Compatible With Truck SUV or LS3 L99 Camaro Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Compatible with a Sanden 508 AC Compressor. Includes belt tensioner, AC compressor bracket, idler pulley, and mounting hardware. Compatible with all GM LS series engines and works with any water pump.

Compatible With Truck SUV or LS3 L99 Camaro Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Includes alternator bracket, power steering bracket, smooth pulley, and mounting hardware. Compatible with all GM LS series engines. Compatible with 1998-02 LS1 Camaro power steering pump pulley.

Compatible With Truck SUV or LS3 L99 Camaro Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Includes Front and Rear Bracket Idler Pulley and Mounting Hardware. Billet Low Mount Alternator Bracket Kit with Pulley. Compatible with any LS Powered Vehicle Alternators with any Amperage.

Requires truckSUV or LS3L99 Camaro crank pulley 12634105. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Includes alternator bracket, idler pulleys, and mounting hardware. will fit any other LS powered vehicle alternators with any amperage. LS Truck Heavy Duty Billet Alternator Bracket Kit LSX 4.8L 5.3L 6.0L Top Driver Head Mount.

Keep your belt from throwing during deceleration with this manual belt tensioner. Easily adjust the tensioner with a 12 drive ratchet. Compatible with LS series GM truck engines. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Includes complete belt tensioner, pulley, and mounting hardware.

Compatible With Truck SUV or LS3 L99 Camaro Crank Pulley. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Includes Alternator Bracket with Turnbuckle Belt Tensioner and Mounting Hardware. Compatible with TruckSUV Alternator use 105 Amp Only. LS Truck Passenger Alternator Relocation Bracket w Turnbuckle Tensioner.

12 Thick Heavy Duty Aluminum Allows More Oil To Flow Through The Engine Internally. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Used When The Engine Oil Cooler Is No Longer Needed. Plugs The Oil Cooler Area Of The Oil Pan, Yet Allows The Oil Passage To Remain Open Inside The Engine. Compatible With 2014 and Newer, LT Series V8 Engines, Chevy Silverado 1500, Tahoe, Suburban, GMC Sierra 1500 Truck, Yukon.

Replaces your vehicles GM LS Gen III IV series engine with the newer style LT series direct injection engine. Compatible with all V8 LT Gen V Engines. Made in Wichita, Kansas from Aerospace Grade, USA Produced, Billet Aluminum. These plates locate the LT engine in the factory LS bellhousing and crankshaft location. Includes 2 Adapter Plates with Bolts.

Engine Mount Brackets. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Includes 2 adapter plates, 8 flat head bolts, and 6 flange M10-1.5 bolts. Made with OEM specifications for the best possible fitment into your vehicle. Natural aluminum finish.

Replace your old stamped steel factory alternator bracket oftentimes won't work with electric water pumps. Bolt on your alternator with this American-made billet aluminum bracket. This bracket uses a slotted tension design to maintain a tight belt.. This bracket kit will come with a satin finish and include all necessary bolts and hardware to mount your alternator.. Made in the USA from aerospace grade billet aluminum. Designed for V-belt systems only using an electric water pump, using Chevy alternators with 6.56 inch, center to center bolt holes 12si style alternators. This alternator bracket will use a 36.5 V-belt, when using factory OEM size pulleys..

This battery tray is designed to securely mount your battery in your vehicle using sturdy base plates and hold-down plates and includes heavy duty 38 hardware. Bottom tray will accept batteries up to 10.5 Length x 6.95 width x 6.7 height with provided thread sleevesbatteries over 7.4 tall will require longer 38-16 all-thread.. Compatible with Most Car and Truck batteries including the following optima sizes Red top 34, 34R, 3478 Yellow top D34, D3478 Blue top 34M, D34M may fit other optima battery sizes. Made in the USA from aerospace grade billet aluminum. Package includes 1 base plate, 1 top plate, 3 all-thread hold downs with nuts, 3 thread sleeves.

This bracket moves the idler pulley over and down, between the alternator and power steering pulleys, to allow LS1 intake manifolds to be used with truck accessory brackets.. Will require modification of factory bracket for intake manifold clearance. Trim as needed for your intake.. Made in Wichita, Kansas from Aerospace Grade, USA Produced, Billet Aluminum. Belt routing will change. Requires belt 780K6 for 105 amp alternators and 787K6 for high output alternators. Natural finish aluminum, includes hardware..

These adapters are used when going from a short Compatible with LS3, LS7, LS9, LSA, or Bosch 210 fuel injector into a taller LS1 intake manifold and fuel rail.. These spacers add approximately 26.7mm 1.05 of length to the fuel injector.. Made in Wichita, Kansas from Aerospace Grade, USA Produced, Billet Aluminum. Included in the package are 8 spacers, and 8 o-rings.. Check out the ICT Billet store for more LS Swap Solutions..

This spacer set allows you to adapt short LS3 fuel injectors into a taller Gen 3 or Gen 4 LS Truck intake manifold and fuel rail.. Commonly used when swapping LS3 injectors on an LS Truck engine.. These spacers adds approximately 12.32mm .48 of length to the fuel injector. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Package includes 8ea injector spacers, 4 fuel rail riser spacers, and 4 fuel rail bolts.

Inline resistor reduces 12 volt power to the correct alternator on signal voltage when not using an ECM. Compatible with 1999 and newer GM LS series engines with 4-terminal, flat alternator connector. Assembled in Wichita, Kansas with USA made OEM grade TXL wire. Includes 1 pigtail with 72 inches of wire lead. Allows use of 105 amp alternator without 5v reference signal from the ECM.

This throttle body adapter will allow you to install a 4 bolt LS throttle body onto a 3 bolt LS intake. For example, a 92mm billet throttle body. Adapter Has 75mm Through Hole, Tapered To 92mm For The Throttle Body.. Compatible With Both DBW And DBC 4 Bolt Throttle Bodies.. Made in Wichita, KS from aerospace grade, USA billet aluminum.. Throttle Body Adapter Will Come With A Adapter Plate, All Bolts, And An Oring Seal Needed For Installation..

Saves Room Under The Hood And Gives The Engine Bay A Custom Look. Compatible With LLY LBZ LMM 6.6L 2004.5 2005 2006 2007 2008 2009 2010 Chevy Duramax Diesel Engines. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Increases Intake Sound. Includes 1 Resonator Adapter with Orings.

Moves the alternator out down. Brings power steering pump in closer from stock location. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Includes 1 front 1 back bracket, 1 idler pulley, and all required mounting hardware. Compatible with TruckSUV 1999-2014 LS series engines.

BBC alternator and power steering pump bracket for electric water pump. Compatible with BBC engines with electric water pump, must use long water pump pulleys and 36P1435 style power steering pump. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Includes alternator bracket, power steering pump bracket, instructions, and mounting hardware. Works with serpentine and V-belt pulleys.

Used to raise valve covers for valve train clearance. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. These will require a gasket andor sealer on both sides of the spacer. Includes 2 spacers, and mounting hardware. Billet 34 Valve Cover Spacer.

Compatible with big block Chevy engines. Made in Wichita, Kansas From Aerospace Grade, USA Produced, Billet Aluminum. Compatible with long water pump. This kit will work with V-belt 1, 2, or 3 rib pulleys and Serpentine belt pulleys. Includes pump bracket, instructions, and mounting hardware.

Relocates LS1 Gen III knock sensors from valley pan to side skirt of the engine block. Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum. Compatible with all LS gen III harnesses and gen III knock sensors. Fits engine RPO codes LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33. Includes 2 billet aluminum knock sensor brackets and mounting hardware.

Conveniently add a 18 NPT port into your top radiator hose to feed your cylinder head crossover tube to. Compatible with 1-14 upper radiator hoses factory LS vehicle size. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Machined aluminum finish. Package Includes 1 hose barb coupler.

Compatible With SBC Engines With Double Hump Heads Or Standard Heads. Compatible With A V Belt System. Compatible With A Long Style Water Pump. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Includes Alternator Brackets, Power Steering Pump Brackets, And All Required Mounting Hardware..

This drill template allows you to mark the center point for drilling and tapping the second mounting hole for, low mount alternators or other accessories, in LS truckSUV iron blocks.. Allows you to mark the center point for precise drilling tapping location.. Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum. Included in the package is 1 aluminum drill template.. Check out the ICT Billet store for more LS Swap Solutions..