Compatibility The oil catch can is compatible with 2018-2024 Jeep Wrangler 3.6L.. Function The 130ml oil separator effectively captures oil vapor and contaminants. It helps extend engine life and keep it running smoothly and cleanly.. Precision Filtration Utilizes a fine mesh aluminum filter to capture even the smallest oil vapors, The rotating disassembly tank base for effortless take out and drainage of spent oil, while an integrated O-ring seal safeguards against leaks. Custom Mounting Fitment Designed with the engine layout in mind, they include required hose, custom brackets and aluminum quick connect fittings. This means installation is more easy, with less need for modifications or additional adapters. Including installation instructions. Note It is recommended to check whether the oil separator needs cleaning after driving 800 to 1600 miles. Due to the high sensitivity of the pressure sensor, the check engine light may trigger above 4000 ft elevation..

FitmentCompatible with 2011-2021 F150 5.0L with RoushWhipple superchargers,2017-2021 Raptor 3.5L Ecoboost,2018- 2021 Expedition 3.5L EcoBoost,2011-2021 F150 3.5L Ecoboost,2015-2021 F150 2.7L Ecoboost. Increases Horsepower Keep Engine CleanCatch the oil and moisture in the blow-by gas that causes carbon and sludge build-up in the intake system and the engine Prevent the dirt and oil from your intake system into your car engine keep the engine clean and preserve engine life. Durable Aluminum MaterialMade of anodized aluminum for eresistant to high temperature and pressure, not easy to be damaged and lasted for long time. Rotating out the dipstick allows you to observe the oil level directly. Easy to Use CleanThis oil separator reservoir tank came with dipstick, measuring fluid level no need to open the can. The material of it is polished, Just need to unscrew the bottom part of the reservoir, so its easy to clean, no need any tools. Easy To Install BaffledThe top mounting braket of oil tank allows it to be mounted from multiple angles to fit for your car, package includes mounting hardware for your installation. Removable baffles inside can also store additional filter media for better filtration. Package Content1xOil Catch Can,1xBracket,2xFuel Line and necessary acessories.

Fitment This trash can is compatible with 2021 2022 2023 2024 2025 2026 Ford F150, serving as a practical accessory to meet family daily needs. The capacity of the trash can is 7.4L. Note ONLY for 40Console40 with flow-through center console, NOT for 402040 with jump seat.. Material The entire trash can is crafted from tough ABS plastic, withstand all weather without warping or cracking. Its three-piece design features a lid, body, and base that snap together securely. The textured lid surface conceals fingerprints while adding a stylish touch. Smooth edges eliminate sharp corners for safety, and the sleek plastic surface wipes clean in seconds.. Function Toss in tissues, packaging, or empty cans. A light press on the lid triggers the spring-loaded closure, instantly sealing away trash and odors. The low-profile design fits perfectly beneath the rear center armrest, ensuring all air vents and charging ports remain fully accessible. Operate with one hand for effortless use while driving. When passengers join the backseat, the lid instantly conceals clutter.. Installation Slide the base under the console, align the two holes, and tighten the screwscomplete in under a minute. No drilling required. The bin slides effortlessly into the slot, with the lid secured by a snap-on latch. It stays firmly in place even on bumpy roads. To empty, simply lift the bin, remove the lid, and rinse.. Warranty If you have problems about the 2021-2026 Ford F150 Trash Can, please tell us and we are willing to help..

Protect your engine and unlock peak performance Aluminum Oil Catch Can with Baffled Filter, 38 NBR Fuel Line Kit Black 300ml Say goodbye to oily intake, carbon buildup, and hidden engine damage Keeps your PCV system clean and intake spotless. Transforms hot oil vapors into liquid before they can harm your engine Ensures smooth motor operation and improved throttle response Built for drivers who demand perfection Premium baffled filter captures oil effectively. Crafted from high-quality aluminum Durable, corrosion-resistant, and sleek under-hood look Built-in dipstick allows easy fluid checks Removable bottom makes draining effortless and mess-free. Universal 38 NBR fuel line kit with M161.5 threaded inletoutlet Fits most cars, SUVs, and trucks Professional-grade protection without complicated installation In freezing temperatures, clean weekly or reinstall original PCV hose. Invest in a catch can that keeps your ride running at its best Prevents costly repairs and keeps your intake spotless Perfect for car enthusiasts who value reliability, longevity, and peak performance.

Baffled Oil Catch Can Design Equipped with a removable baffle and steel ball filter media, this oil catch can effectively traps oil vapor and moisture. It prevents carbon buildup in the intake tract, valves, and pistons, keeping your engine clean, running smoothly, and extending its lifespan.. Universal Fit - With a 300ml capacity, this catch can is compatible with most vehicles. Please ensure there is sufficient space for installation. Fuel Fitting Kits Comes with Metric M16x1.5 to 6AN 8AN 10AN fuel fitting straight.. PCV System Compatibility This universal air oil separator can be installed with or without a breather filter. Use with breather filter as a vent system on pre-PCV vehicles, or install inline between PCV hoses as a sealed catch can setup.. Note In low temperatures, excess crankcase moisture may freeze. To avoid blockages, clean the catch can weekly or reinstall the original PCV hose during freezing conditions..

Baffled Oil Catch Can Design Equipped with a removable baffle and steel ball filter media, this oil catch can effectively traps oil vapor and moisture. It prevents carbon buildup in the intake tract, valves, and pistons, keeping your engine clean, running smoothly, and extending its lifespan.. Universal Fit - With a 300ml capacity, this catch can is compatible with most vehicles. Please ensure there is sufficient space for installation. Fuel Fitting Kits Comes with Metric M16x1.5 to 6AN 8AN 10AN fuel fitting straight.. PCV System Compatibility - Oil Catch Can with or without Breather Filter Install the oil catch can with breather filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can. Note In low temperatures, excess crankcase moisture may freeze. To avoid blockages, clean the catch can weekly or reinstall the original PCV hose during freezing conditions..

UniversalIt can be applied to most cars, making sure there's enough room for Installation.. Size Hose length 31.5in 0.8m,hose ID38,hose OD23.The thread of the inlet and outlet is M161.5.Capacity300ML.. Baffled The baffle is disassembled in a rotary manner, adding an appropriate amount of steel balls can increase the surface area of steam condensation and more effectively catch oil.. Note When the temperature outside reaches the freezing point or below, the crank vent system will generate a much greater amount of moisture which can present a risk of freezing. Please clean your oil catch can on a weekly or install the original PCV hose.. Warranty EVIL ENERGY provide this product 3-month warranty. Any problem you might have, please feel free to contact us via Amazon message..

Fitment Compatible with 2011-2023 F-150 5.0L, 2011-2023 F-150 5.0L with RoushWhipple superchargers, 2011-2023 F-150 3.5 EcoBoost, 2015-2023 F-150 2.7L EcoBoost, 2017-2023 Raptor 3.5L EcoBoost, 2018-2021 Expedition 3.5 EcoBost.. Installation Location In most cases you only need an air oil separator on the PCV side of the engine.. Note It is recommended to check whether the oil separator needs cleaning after driving 500 to 1000 miles.. Function The fine mesh aluminum filter captures fine oil vapor, helping to extend engine life and keep it running smoothly and cleanly.. Easy installationEquipped with the required hoses, custom brackets and fittings for direct replacement. Including installation instructions..

Application Compatible with Ford F150 5.0L Modular V8 2011-2024, Compatible with Ford F150 3.5L Ecoboost V6 2011-2024, Compatible with Ford F150 2.7L Ecoboost V6 2015-2024, Compatible with Ford Expedition 3.5L EcoBoost V6 2018-2021.. Enhanced Filtration The oil catch can comes with removable baffles for adding steel wire balls as additional filter media to enhance filtration efficiency.. Premium Construction Made from anodized aluminum for high-temperature and pressure resistance, with a leak-proof O-ring design and a dipstick for easy oil level checks.. Engine Protection Our oil catch can helps prevent carbon buildup in the intake valves, ensuring a cleaner engine for optimal performance.. Easy Installation Includes 350ml oil catch can with and without filter options, 18 21 inches NBR fuel line with adapters and mounting hardware. The catch can without filter can only be used as a seal can..

Baffled Oil Catch Can Design Equipped with a removable baffle and steel ball filter media, this oil catch can effectively traps oil vapor and moisture. It prevents carbon buildup in the intake tract, valves, and pistons, keeping your engine clean, running smoothly, and extending its lifespan.. Universal Fit - With a 300ml capacity, this catch can is compatible with most vehicles. Please ensure there is sufficient space for installation. AN10 CPE Hose Package Comes with a 5FT AN10 CPE fuel hose, AN10 swivel fittings 0 and AN10 swivel fittings 90. Also included metric M16x1.5mm to 6AN 8AN 10AN male flare adapter straight fuel fitting.. PCV System Compatibility This universal air oil separator can be installed with or without a breather filter. Use with breather filter as a vent system on pre-PCV vehicles, or install inline between PCV hoses as a sealed catch can setup.. Note In low temperatures, excess crankcase moisture may freeze. To avoid blockages, clean the catch can weekly or reinstall the original PCV hose during freezing conditions..

Package Content1150ml 2-Port Oil Catch Can, 110FT 38 NBR fuel line, 2Adapters, 1Adapters for Filter, 1Filter wClamp, 1Drain Valve, 2Screws Gaskets, 2Clamps.. with 10FT NRB Fuel Line ID 3810MM, OD 23 17MM. Working Pressure 300PSI 2.0Mpa Burst Pressure1160PSl 8Mpa.. Multiple Installation Options In-line Crankcase Hose wo Filter, Pre-Crankcase w Filter. The filter keeps impurities out and maintains an open system.. Keep Engine Clean The low micron bronze filter and dual filtration design effectively filter impurities and are detachable for cleaning.. Attention It is normal for the conical thread adapter to not fully enter the oil collection tank and does not affect the sealing effect..

Large Capacity 750ML breather catch can with 10AN fittings 78-14 UNF and a 38 NPT bottom valve. Big enough for high-performance setups.. Wide Compatibility Universal oil catch can fits most vehicles. Just ensure enough engine by space for proper installation.. Easy Draining Built-in drain valve lets you empty and reuse the catch can without removing itquick, clean, and convenient.. Engine Protection This catch can separates oil from PCVCCV vapors, keeping your intake valves clean and extending engine life.. Leak-Free Design Durable build with tight-seal fittings. For best results, follow the included catch can installation guide..

Baffled Design Featuring a removable baffle and adding an appropriate amount of steel wool, this oil catch can effectively traps oil and moisture, preventing carbon buildup. By keeping your engine's intake, valves, and pistons clean, it helps maintain optimal performance and extends engine lifespan. Universal Fit With a 300ml capacity, this catch can is compatible with most vehicles. Please ensure there is sufficient space for installation. Durable NBR Fuel Hose Kit Includes a high-quality NBR hose known for its exceptional wear and heat resistance. Hose length 5ft 1.5m ID 38 OD 58. The inlet and outlet ports feature an M161.5 thread for a secure fit. PCV System Compatibility Oil Catch Can with or without Breather Filter Install the oil catch can with breather filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can. Note In freezing temperatures, the crank vent system generates increased moisture, which may lead to freezing risks. To prevent blockages, clean the catch can weekly or reinstall the original PCV hose in cold weather conditions. After-sales Service We stand by the quality of our oil catch can. If theres a quality issue, well take care of a return or exchangeno hassle. Have questions or need help Our customer service team is here to provide fast, professional support whenever you need it.

Fitment Vehicle This Oil Separator Kit Compatible with F-150 5.0L 2011-2023, F-150 5.0L with RoushWhipple superchargers 2011-2023, F-150 3.5L EcoBoost 2011-2023, F-150 2.7L EcoBoost 2015-2023 Compatible with Ford Expedition 3.5L EcoBoost 2018-2021 Compatible with Ford Raptor 3.5L EcoBoost 2017-2023.. Upgrade structure Disassembly is easy, just unscrew the bottom of the oil Catch Can, using more reliable and sturdy NBR hoses, a fine mesh aluminum filter, strengthen the hose clamp to prevent the hose from falling off.. Product Function QBselecar Oil Separator Kit captures oil vapor through a fine mesh aluminum filter, prevent carbon and dirt buildup in the intake system and engine, extending the engine's lifespan.. Package IncludesQBselecar Oil Catch Can Kit include Aluminum pot body, Stainless steel bracket, Bolts and Nuts, NBR fuel hoses with fittings, seal tape.. Premium Service QBselecar is committed to providing customers with high-quality and cost-effective auto parts products, with each product being checked before it reaches your hands. If you have any product issues, please contact us, and we will respond to you within 24 hours..

Fitment Universal Baffled oil catch can fits for most cars, just make sure enough space to Install. Function The oil catch can kit can be installed with breather filter for pre-PCV cars as a vent system, or without breather filter in line between PCV hoses as a seal canbreather filter is not included. Parameter The oil catch can has a capacity 300ML Hose ID 38 Hose OD58 Hose length 31.5in 0.8m Inlet and outlet thread M161.5. Notice When the environment temperature reaches or below the freezing point, the vent system will generate a large amount of moisture which may present a risk of freezing. Weekly clean or original PCV hose is recommended. Install We advice more replacements from VehiMata for your fuel systems for a better compatibility, professional installation is highly recommended.

FITMENTThis oil catch can kit compatible with 2011-2021 F-150 5.0L2011-2021 F-150 5.0L with RoushWhipple superchargers2011-2021 F-150 3.5L 2015-2021 F-150 2.7L 2017-2021 Raptor 3.5L 2018-2021 Expedition 3.5 .. PRESERVE ENGINE LIFEINCREASES HORSEPOWERThe catch can will keep out the dirt and oil get inside your engine from your intake system. To keep engine clean , Increases horsepower and Preserve Engine Life.. InstallationThe oil catch can top mounting bracket allows mounting from multiple angles to fit your car, easy and convenient.. 400ML CAPACITY- The capacity is 400ml,enough for daily use.. FEATUREIt is fully Tig Welded and Thread Come with O-ring Gasket to Prevents oil leakage. Just need to unscrew the bottom part of the reservoir, easy to clean.And it's also very lightweight,very suitable for installation in your car or motorcycle..

Oil Catch Can Separate oil particles from PCVCCV to prevent intake valve carbon accumulation and keep the engine clean.. Durable Made of anodized aluminum, resistant to high temperature and pressure. Will not leak with O-ring. Rotating out the dipstick allows you to observe the oil level directly.. Application Compatible with Ford 11-22 F150 5.0L or with RoushWhipple superchargers,11-22 F150 3.5L Ecoboost, 15-22 F150 2.7L Ecoboost, 17-22 Raptor 3.5L Ecoboost, 18-22 Expedition 3.5L EcoBoost.. Baffled Removable baffles inside can also store additional filter media for better filtration.. Easy to install You can use the 350ml oil catch can with breather filter as a vent system or a seal can..

Wide Compatibility for Specific Ford ModelsCompatible with 2011-2023 F150 5.0L including models with RoushWhipple superchargers, 2011-2023 F150 3.5 EcoBoost, 2015-2023 F150 2.7L EcoBoost, 2017-2023 Raptor 3.5L EcoBoost, and 2018-2021 Expedition 3.5 EcoBoost. This oil catch can is perfectly fitted to these specific vehicles, with a design that blends seamlessly with factory components, complementing your vehicles original aesthetics and layout without visual inconsistency.. Core Function Protect Engine Life Performance This oil catch can oil separator effectively captures oil vapor and contaminants from the PCV system. By preventing oil buildup in the engine, it keeps the engine running smoothly and cleanly, directly extending engine service life and maintaining optimal performance.. recision Filtration Leak-Proof Design Features a fine mesh aluminum filter to trap even the smallest oil vapors, ensuring thorough filtration. The rotating disassembly tank base allows effortless removal and drainage of collected oil, while an integrated O-ring seal provides reliable leak protection, avoiding messy oil spills.. Custom Mounting Kit for Easy Installation Comes with all necessary accessories required hoses, custom brackets, and aluminum quick connect PCV fittings. Designed based on the target engines layout, it minimizes the need for modifications or additional adapters. Detailed installation instructions are included, making the setup process fast and hassle-free.. PCV Side Installation Maintenance Tip In most cases, this air oil separator only needs to be installed on the PCV side of the engine, aligning with standard engine ventilation systems. For long-term efficiency, it is recommended to check and clean the oil separator after every 500 to 1000 miles of driving..

FitsOur oil catch can kit is compatible with 2011-2023 F-150 5.0L, 2011-2023 F-150 5.0L with RoushWhipple Superchargers, 2011-2023 F-150 3.5L Ecoboost, 2015-2023 F-150 2.7L Ecoboost, 2017-2023 Raptor 3.5L Ecoboost, 2018-2023 Expedition 3.5L EcoBoost.. FeatureMade of anodized aluminum, resistant to high temperature and pressure. Will not leak with O-ring. It's very lightweight, suitable for installation in your car or motorcycle. The sight glass lets you know the amount of oil in the can.. FunctionSeparate oil particles from PCVCCV, it prevents dirt and oil get inside your engine from your intake system, thus keeping the engine clean and prolonging its life.The maxed capacity of the tank is 400ml, compact size, easy to use and clean.. InstallationThe top mounting bracket allows mounting from multiple angles to fit your car. And you just need to unscrew the bottom part of the reservoir to clean it easily.. After salesIf you have any problem, please contact us at the first time, we are always here to support you. You can buy it with confidence..

Baffled Oil Catch Can Design Equipped with a removable baffle and steel ball filter media, this oil catch can effectively traps oil vapor and moisture. It prevents carbon buildup in the intake tract, valves, and pistons, keeping your engine clean, running smoothly, and extending its lifespan.. Universal Fit - With a 300ml capacity, this catch can is compatible with most vehicles. Please ensure there is sufficient space for installation. AN6 CPE Hose Package Comes with a 5FT AN6 CPE fuel hose, AN6 swivel fittings 0 and AN6 swivel fittings 90. Also included metric M16x1.5mm to 6AN 8AN 10AN male flare adapter straight fuel fitting.. PCV System Compatibility - Oil Catch Can with or without Breather Filter Install the oil catch can with breather filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can. Note In low temperatures, excess crankcase moisture may freeze. To avoid blockages, clean the catch can weekly or reinstall the original PCV hose during freezing conditions..

FitsOur oil catch can kit is compatible with 2011-2023 F-150 5.0L, 2011-2023 F-150 5.0L with RoushWhipple Superchargers, 2011-2023 F-150 3.5L Ecoboost, 2015-2023 F-150 2.7L Ecoboost, 2017-2023 Raptor 3.5L Ecoboost, 2018-2023 Expedition 3.5L EcoBoost.. FeatureMade of anodized aluminum, resistant to high temperature and pressure. Will not leak with O-ring. It's very lightweight, suitable for installation in your car or motorcycle. The sight glass lets you know the amount of oil in the can.. FunctionSeparate oil particles from PCVCCV, it prevents dirt and oil get inside your engine from your intake system, thus keeping the engine clean and prolonging its life.The maxed capacity of the tank is 400ml, compact size, easy to use and clean.. InstallationThe top mounting bracket allows mounting from multiple angles to fit your car. And you just need to unscrew the bottom part of the reservoir to clean it easily.. After salesIf you have any problem, please contact us at the first time, we are always here to support you. You can buy it with confidence..

SizeHeight without filter96mmHeight with filter163mmWidth 63mm.InletOutlet38 NPTPlug Adapter9.5mm12.7mm. This Oil Catch Can is fit for small spaces.. High Quality100 Billet, 6061 Aluminum, Anodized Surface which ensures the High-temperature resistance and corrosion resistance, achieving optimal durability and lifespan.. Performance upKeeping the engine intake, valves, and pistons clean will not lose power in the future.. FunctionWith this oil catch can you keep your engine clean under hard driving conditions allowing cleaner gases to be passed back into the intake.. Fit forThis Oil Catch Can is fit for small spaces and also easy to clean.Universal fit for most car,compatible with Honda Toyota Nissan Lexus Mazda Jeep Dodge Ford Chevy Volvo etc..

Compact Size The PQY oil catch can has a small body,can save the pace in your engine. Universal Fittment The universal oil catch can tank can be used on many cars.Just make sure there is enough space in your engine to install it. Baffled Oil Catch Can The oil reservoir tank separates oil particles by using 50 micron bronze filter. Defends intercooler, intake system and essential components from oil blow-by.Helps maintain proper octane levels to reduce potential detonation. Material The baffled 2 port oil catch can is made of 6061 aluminum with black coating,features M16 x 1.5 threads of inlet and outlet. Package Includes The oil catch tank kit comes with 2pcs black anodized, CNC-machined aluminum hose fittings.

Compatible with 2011-2023 F150 5.0L2011-2023 F150 5.0L with RoushWhipple superchargers2011-2023 F150 3.5L Ecoboost2015-2023 F150 2.7L Ecoboost2017-2023 Raptor 3.5L Ecoboost2018-2023 Expedition 3.5L EcoBoost.. Portable Separator The sight glass lets you know the amount of oil in the can.The maxed capacity of the tank is 400ml, compact size, easy to use and clean.After installing the valve, when it gets too full of oil, you just need to unscrew the valve to empty its contents without reinstalling and it could be reused constantly.. Features One inlet and one Exit Filter and can are both fully serviceable.Internal air diverter turbulates air longer to improve oil separation.. Multiangle Installation The top mounting braket of oil tank allows it to be mounted from multiple angles to fit for your car, package includes mounting hardware for your installation.. Support For any questions or concerns regarding the oil separator catch can kit, please inform us so we can resolve the issue.

The capacity of the tank is 750 ml about 25.3 oz, which is easy to clean and generally fit for most cars.. With this oil catch can you keep your engine clean.keeping the engine intake,valves and pistons clean will not loss power in the future.. The baffle system in the tank could catch the oil and moisture, prevent misfires due to carbon accumulation, keep the engine clean, and prolongs engine life.. High-quality aluminum and the anodized technology make the catch can strength,durable with a beautiful appearance.. Packing Include1 x Billet aluminum Oil catch can1 x Filter1 x Hose Clamp1 x Drain Valve5 x Hose connectorAs the picture shows.If you have any problems, contacting us and we will serve you within 24 hours..

Universal 400 mlThe air oil separator catch can kit fits for most cars and small parts of motorcycles. And the capacity of the polish baffled reservoir is 400 ml, enough for daily use. High QualityThe oil catch can crafted from lightweight aluminum offers strength and durability. Note Surface scratches may occur due to the aluminum material, but they do not affect usage effect. The anodized finish enhances its aesthetic appeal. FunctionThe baffled oil catch can traps oil and moisture, preventing carbon buildup. The baffle cools vapor into liquid, collected at the bottom, keeping the engine clean and extending its life by minimizing waste oil vapor re-circulation. Upgrade StructureHose clamps reinforce to prevent detachment. Adapters in 3 sizes with o-ring gaskets fit various hoses, preventing leaks. The built-in dipstick checks fluid levels without frequent opening. Use the breather filter for venting. 2 Types of InstallationEasy to install the baffled oil catch tank with breather filter as a vent system or without breather filter as a seal can, both for your option.

FitmentThis oil catch can kit compatible with 2011-2021 F-150 5.0L2011-2021 F-150 5.0L with RoushWhipple superchargers2011-2021 F-150 3.5L2015-2021 F-150 2.7L2017-2021 Raptor 3.5L2018-2021 Expedition 3.5L.. 400ML CapacityThe capacity of the polish baffled reservoir is 400ml,enough for daily use.. InstallationThe oil catch can top mounting bracket allows mounting from multiple angles to fit your car, easy and convenient.. Upgrade structureThe baffle can cool the hot oil steam and turn it into liquid, capture oil and wet oil steam, keep the engine clean and prolong the service life of the engine. Strengthen the hose clamp to prevent the hose from falling off.. CharacteristicAll TIG welding, thread with O-ring seal to prevent oil leakage. Simply unscrew the bottom of the reservoir for easy cleaning. And very light, very suitable for installation in cars or motorcycles..

HIGH QUALITY Made of high quailty 6061 Aluminum material, durable, heat-resistant and corrosion-resistant.. FUNCTIONCatch oil and moisture in PCVCCV air, prevents misfire due to carbon buildup, keeps engine clean and extends engine life.. PACKAGE INCLUDED1 x Oil Catch Can, 1 x Breather Filter, 1 x Drain Valve, 1 x Hose Clamp, 5 x Hose connector.. NOTEThis oil catch can compatible with most cars. When it is filled with oil, you will need to empty it and clean it so it can be used again.. Service We offer 1 year product quality support to our customers. Any questions please feel free to contact us, we will reply to you within 24 hours.

Durable Aluminum Quality Made of anodized aluminum for eresistant to high temperature and pressure, not easy to be damaged and lasted for long time. Fitment Our oil catch can kit is compatible with 2011-2021 F-150 5.0L, 2011-2021 F-150 5.0L, 2011-2021 F-150 3.5L Ecoboost, compatible with 2015-2021 F-150 2.7L Ecoboost, 2017-2021 Raptor 3.5L Ecoboost, 2018-2021 Expedition 3.5L EcoBoost. Increases Horsepower Keep Engine Clean This Oil Separator can catch the oil and moisture in the blow-by gas that causes carbon and sludge build-up in the intake system and the engine. It will prevent the dirt and oil from your intake system into your car engine which can keep the engine clean and preserve engine life. Multi-angle Installation Mounting brackets included with the Oil Separator allow mounting from multiple angles to fit your car, easy installation in under 30 minutes. Easy to Use Clean This oil separator reservoir tank came with dipstick, measuring fluid level no need to open the can. The material of it is polished, Just need to unscrew the bottom part of the reservoir, so its easy to clean, no need any tools.

Durable Aluminum Quality Made of anodized aluminum for eresistant to high temperature and pressure, not easy to be damaged and lasted for long time. Fitment Our red oil catch can kit is compatible with 2011-2021 F-150 5.0L, 2011-2021 F-150 5.0L, 2011-2021 F-150 3.5L Ecoboost, compatible with 2015-2021 F-150 2.7L Ecoboost, 2017-2021 Raptor 3.5L Ecoboost, 2018-2021 Expedition 3.5L EcoBoost. Increases Horsepower Keep Engine Clean This Oil Separator can catch the oil and moisture in the blow-by gas that causes carbon and sludge build-up in the intake system and the engine. It will prevent the dirt and oil from your intake system into your car engine which can keep the engine clean and preserve engine life. Multi-angle Installation Mounting brackets included with the Oil Separator allow mounting from multiple angles to fit your car, easy installation in under 30 minutes. Easy to Use Clean This oil separator reservoir tank came with dipstick, measuring fluid level no need to open the can. The material of it is polished, Just need to unscrew the bottom part of the reservoir, so its easy to clean, no need any tools.

The baffle system in the Oil Catch Can Kit could catch the oil and moisture from PCVCCV air, prevent misfires due to carbon accumulation, keep the engine clean and prolongs engine life. Don't use the filter on a PCV system, you'll just break the vacuum and cause engine problems. This filter applies only to the front of the PCV system.. Our Oil Catch Can Kit has a removable baffle that can store additional filter media. Oil Catch Can have a built-in dipstick to check fluid level and a removable bottom to drain making it reusable, hose clamp reinforcement to prevent the hose from falling off.. The Oil Catch Can Kit uses NBR 38 hose which is Excellent oil resistance resistance to mineral oil, liquid fuel, high wear resistance, good heat resistance. You don't need to buy an additional hose.. Our Oil Catch Can Kit has hoses, clamps, and mounting brackets which are made of aluminum, lightweight, and durable. It can greatly prolong the service engine life of your car.. When the temperature outside reaches the freezing point or below, the crank vent system will generate a much greater amount of moisture which can present a risk of freezing. Please clean your oil catch can on a weekly or install the original PCV hose..

UniversalIt can be applied to most cars, making sure there's enough room for Installation.. Size Hose length 2.6ft 0.8m,hose ID38,hose OD23.The thread of the inlet and outlet is M161.5.Capacity300ML.. Breather Filter You can install the oil catch can with Breather Filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can, all for your option.. Note When the temperature outside reaches the freezing point or below, the crank vent system will generate a much greater amount of moisture which can present a risk of freezing. Please clean your oil catch can on a weekly or install the original PCV hose.. Oil Catch Can with or without Breather Filter Install the oil catch can with breather filter for pre-PCV cars as a vent system or without breather filter in line between PCV hoses as a seal can.. After-sales Service We stand by the quality of our oil catch can. If theres a quality issue, well take care of a return or exchangeno hassle. Have questions or need help Our customer service team is here to provide fast, professional support whenever you need it.

FitmentThis oil catch can kit compatible with 2011-2021 F-150 5.0L2011-2021 F-150 5.0L with RoushWhipple superchargers2011-2021 F-150 3.5L 2015-2021 F-150 2.7L 2017-2021 Raptor 3.5L 2018-2021 Expedition 3.5 .. 400ML CapacityThe capacity of the polish baffled reservoir is 400ml,enough for daily use.. InstallationThe oil catch can top mounting bracket allows mounting from multiple angles to fit your car, easy and convenient.. Upgrade structureThe baffle can cool the hot oil steam and turn it into liquid, capture oil and wet oil steam, keep the engine clean and prolong the service life of the engine. Strengthen the hose clamp to prevent the hose from falling off.. CharacteristicAll TIG welding, thread with O-ring seal to prevent oil leakage. Simply unscrew the bottom of the reservoir for easy cleaning. And very light, very suitable for installation in cars or motorcycles..

Baffled Can Can Benefits After installing an oil catch can, this oil catch can could keep your car better.. Strengthened Shell NBR Hose Our research team found that many buyers from the rival complained about the shell's long scratches and the useless, cheap silicone hose. NBR HOSE is more reliable and robust.. Aluminum Bracket for Location Unlike rivals' ordinary accessories configuration, we upgraded the package and included an aluminum bracket, which allows you to fix the oil can at the proper location.. Universal Design and Package Ideal for both vehicles and motorcycles, this catch can with 3 pairs of adapters 6mm 8mm 10mm meets all your needs As long as the space allows.. Kindly Reminder Clean the oil can once a week or install the original hose..

Accessories Compatible with 2019-2022 Chevy Silverado 1500 5.3L and 6.2L, GMC Sierra 1500 5.3L and 6.2L. Compatible with 2021-2022 Chevy Tahoe, Suburban, 2021 GMC YukonYukon XL. Not suitable for 2019 LD Classic.. Capturing Oil and Keeping Engine Clean-- The oil collection tank will collect oil and moisture in the air of PCVCCV, prevent carbon and sludge deposits in the intake system and engine, keep the engine clean and prolong its life.. Good tightness to prevent leaks-- Fully Tig welded and with O-ring gaskets in fittings to prevent oil leaks, ideal for use as a sealed catch tank.. Superior Quality-- Made of high quality 0046 aluminum for added strength and durability, fully tig welded, light weight and corrosion resistant. It is convenient to check the liquid level in the collection tank through the dipstick, without frequently opening the connecting bracket, hose.. Perfect customer service--If you encounter product problems, please contact us, we will help you solve the problem in time..

FitmentCompatible with 2014-2018 Chevy Silverado 1500 5.3L 6.2L,2015-2020 Chevy Tahoe 5.3L 6.2L,2015-2020 Chevy Suburban 5.3L 6.2L,2014-2018 GMC Sierra 1500 5.3L 6.2L,2015-2020 GMC YukonYukon XL 5.3L 6.2L,2015-2019 Cadillac Escalade 6.2L.. Installation LocationIn most cases you only need an air oil separator on the PCV side of the engine.. NoteIt is recommended to check whether the oil separator needs cleaning after driving 500 to 1000 miles.. FunctionThe fine mesh aluminum filter captures fine oil vapor, helping to extend engine life and keep it running smoothly and cleanly.. Easy installationEquipped with the required hoses, custom brackets and fittings for direct replacement. Including installation instructions..

FITMENTThis oil catch can kit compa tible with 2011-2021 5.0L2011-2021 5.0L with RoushWhipple superchargers2011-2021 3.5L 2015-2021 2.7L 2017-2021 Raptor 3.5L 2018-2021 Expedition 3.5 .. PRESERVE ENGINE LIFEINCREASES HORSEPOWERThe catch can will keep out the dirt and oil get inside your engine from your intake system. To keep engine clean , Increases horsepower and Preserve Engine Life.. InstallationThe oil catch can top mounting bracket allows mounting from multiple angles to fit your car, easy and convenient.. 400ML CAPACITY- The capacity is 400ml,enough for daily use.. FEATUREIt is fully Tig Welded and Thread Come with O-ring Gasket to Prevents oil leakage.Just need to unscrew the bottom part of the reservoir, easy to clean.And it's also very lightweight,very suitable for installation in your car or motorcycle..

Efficient Oil Catch Use this oil catch can kit reduce oil and water buildup in your engine use this oil catch can. Oil Separator making sure there's enough room for Installation, suitable for most cars. Oil Catch Cans Size Hose length 31.5in 0.8m, hose ID38, hose OD23. Featuring a convenient 300ml capacity and oil dipstick for hassle-free fluid level checks. Prevent Carbon Build-Up Oil separator automotive prevent carbon and sludge build-up in the intake system and the engine, keep your engine running smoothly and efficiently, keep engine clean and prolongs its life. Easy Maintenance Featuring a convenient 300ml capacity and oil dipstick for hassle-free fluid level checks. This Oil Catch Can Kit is a must-have for any vehicle enthusiast looking to protect their engine and improve overall performance. Enhance Engine Performance Prevent oil vapors and high temperatures from damaging engine components. Meet the solution for enhancing your engine's performance and longevity - our 300ml Oil Catch Can Kit, complete with a coolant reservoir tank.

Compatible withOur Oil Catch Can is compatible with Ford F-150 2011-2025 5.0L, F-150 with RoushWhipple superchargers 2011-2025 5.0L, F-150 EcoBoost 2011-2025 3.5, F-150 EcoBoost 2015-2025 2.7L, Raptor 3.5L EcoBoost 2017-2025, Expedition EcoBoost 2018-2021 3.5.. Catch Can BenefitsFiltering consists of a fine mesh aluminum filter that can catch the oil and moisture from PCVCCV, prevent carbon and sludge build-up in the intake system and the engine, keep the engine clean, and prolong its life.. Kindly ReminderWhen the outside temperature is at or below freezing, the crankshaft ventilation system generates a lot of moisture, posing a risk of freezing. Clean the oil catch can once a week please.. Recommended cleaning mileage It is recommended to clean after driving 500 to 1000 miles.. PackageThis Oil Separator Kit with 1x Aluminum pot body, 1x Aluminum Filter, 2x Bolt, 2x NBR fuel hose with fittingsNBR HOSE is more reliant and robust, 1x Bracket..

3 inch2 inch Leveling kit Shocks struts adopt high-precision dynamic balance detection technology to effectively reduce vehicle impact. Compatible for 2004-2020 for F-150. Safest way to level lift 32 suspension leveling kit Will Raise the front of your truck by 3 inches2 inches , improving the look of your vehicle and providing additional fender clearance for larger tires and wheels. Please note that spacer thickness to lift height, not the 11 ratio. eg.The thickness of a 2 spacer is 1.2, but lifted to a height of 2. Strong Durable SCITOO 3 inch2 inch Leveling kit are made from premium 6061-T6 billet aluminum, with precision CNC machining for a perfect fit. Uses black anodized surface to match your factory suspension Lift kit. High strength hardware with a durable finish. Solid bolts are extremely strong and durable without compressing or warping over time. Leveling kit Benefits ? You can use larger than stock wheels on all corners. It allows you to operate the front of the truck You can avoid the sagging problem of some makes and models. It reduces brake pressure when emergency stop. The truck leveling kit does not affect the static weight balance of the vehicle. Better handling with truck leveling kit installed. Easy to Install Bolt-on installation is convenient and easy. No need to strutssprings to install these suspension leveling kit, Simple Bolt-On. Custom fit for each application. Please pay attention to the parts of your model when purchasing, this product is for coil springs.

Content1Billet Catch Can, 1Breather Filter2 Braided Hoses,1 Bracket, and Other Accessories.. Durable Aluminum QualityMade of anodized aluminum for eresistant to high temperature and pressure, not easy to be damaged and lasted for long time. Oil Catch CanSeparate oil particles from PCVCCV to prevent intake valve carbon accumulation and keep the engine clean. BaffledRemovable baffles inside can also store additional filter media for better filtration.. Easy to Use CleanThis oil separator reservoir tank came with dipstick, measuring fluid level no need to open the can. The material of it is polished, Just need to unscrew the bottom part of the reservoir, so its easy to clean, no need any tools.

Keep Engine CleanThe oil catch tank will catch the oil and moisture from PCVCCV air, prevent carbon and sludge build-up in the intake system and the engine, keep engine clean and prolongs its life.. Prevent Oil LeakThe oil catch can kit can effectively reduce the fuel consumption of high-speed engines and turbine engines. Extend engine life.Fully tig welded and come with O-ring gasket, hose clamps to prevents oil leakage.. 350ML Capacity for Universal Car350ml Capacity catch can comes with 3 types of adapters, Universal for most car.. Superior 0046 Aluminum MaterialThis Oil Catch Can is Made of high quality 0046 aluminum for added strength and durability, fully tig welded, lightweight and corrosion resistant.. Valuable Oil Catch Can KitPackage includes 1xOil Catch Can,1xFuel line,1xStainless Steel Wool,6xFittings,1xThread Seal Tape and necessary screws. Come with Oil Dipstick-It is convenient to check the fluid level in catch can by oil dipstick without opening it frequently..

Universal and REUSABLE Air breather oil catch can be applied to most cars, As long as you know how to route the hose making sure there's enough room for Installation. When it gets too full of oil you need to empty it and clean it for reuse.. FUNCTIONS oil catch can be reducing the amount of steam entering the intake branch, and reduce the probability of secondary combustion. So it can increase horsepower, preserve engine life and keep the engine clean.. Worth BuyingOur oil catch can the hose clamp reinforcement to prevent the hose from falling off,it have a washable stainless screw-on filterbreather with Hose Clamp to stop it from coming loose with vibration. Also, you can choose not to install.. High QualityOur oil catch can is made of high-quality aluminum and is anodized, which is not only high in strength, durable, but also has a beautiful appearance.. WARRANTY- POSENG provides oil catch can have a 4-month warranty. If you have any problems, contacting us and we will serve you within 24 hours..

300ML Capacity UniversalThe air oil separator catch can kit fits for most cars and small parts of motorcycles. And the capacity of the polish baffled reservoir is 300ml,enough for daily use.. Washable Breather FilterSeparates oil particles from PCVCCV air using 50 micron bronze filter. Defends intercooler, intake system and essential components from oil blow-by. Helps maintain proper octane levels to reduce potential detonation.. Good Sealing to Prevent LeakageFully Welded and comes with O-ring gasket in fittings to prevent oil leakage, works great as a sealed catch can.. Premium Durable QualityMake of High Quality Billet,6061 Aluminum, Anodized Surface, high temperature resistance and corrosion resistant for optimal durability and longevity.. Keep Engine CleanThe baffle system could catch the oil and moisture from PCVCCV, prevent misfires due to carbon accumulation, keep engine clean and prolongs engine life. 2 TYPES OF INSTALLATION - Easy to install oil catch can with breather filter as a vent system or without breather filter as a seal can, all for your option..

High-Quality Materials This baffle-type oil separator is made of aluminum alloy, silicone, and stainless steel, featuring high hardness and durability. The oil separator effectively captures oil and moisture, prevents carbon buildup, is corrosion-resistant, rust-proof, and resistant to aging, ensuring a long service life.. Excellent Sealing Performance The fuel vapor separator can also function as a sealed tank. Remember to use the O-ring seal provided in the packaging on the accessories. It offers superior sealing performance, effectively preventing oil leaks, keeping the interior clean, and making your daily maintenance easier.. PCV Function CompatibilityThe fuel tank vent filter captures oil and moisture from the PCV intake, preventing carbon buildup and oil sludge in the intake system and engine, keeping the engine clean, and extending engine life. If not using the vent filter, install it between the PCV hoses as a fuel tank seal.. Wide CompatibilityThe oil-gas separator has a capacity of 300ML, and the packaging includes three sizes of adapter accessories 6mm, 8mm, and 10mm. It is suitable for most vehicles. Please ensure there is sufficient installation space.. Product Includes You will receive 1 x 300ML breathable fuel tank, height 4.4 inches, diameter 2.7 inches. 1 x Breathing Filter, 1.5 inches in height, 2 inches in diameter. 1 x Oil Tube, 3 x Clamps, 6 x Adapter Accessories 2 x 6mm, 2 x 8mm, 2 x 10mm, 2 x Screws, 2 x Nuts, 6 x O-Rings..

Premium Material This baffle type oil catch can is made of aluminum alloy, silicone and stainless steel, high strength, strong and durable. It easily captures oil and moisture in the air, does not rust, is corrosion resistant, not easy to age, and has a long service life.. Perfect Sealing It also works great when used as a sealing can Remember to use the O shape ring seal in the package on the fitting, it provides superior sealing performance, effectively prevents oil leakage, keeps the interior clean, and makes your daily maintenance more effortless.. Function After installing the oil collection tank, it can collect the oil and water in PCVCCV, prevent carbon and sludge from accumulating in the intake system and engine, keep the engine clean and extend its life The built-in dipstick is used to check the liquid level, and the removable bottom is used for drainage, making it reusable and easier to clean.. Easy Maintenance Featuring a convenient 300ml capacity. This Oil Catch Can Kit is a must-have for any vehicle enthusiast looking to protect their engine and improve overall performance.. What You Will Get 1 x 300ML breathable oil catch can, which is 4.4 inches high and 2.7 inches in diameter. 1 x breather filter, which is 1.5 inches high and 2 inches in diameter. 1 x oil hose, 3 x clamps, 6 x adapter fittings 2 x 6mm, 2 x 8mm, 2 x 10mm, 2 x screws, 2 x nuts, 6 x O shape rings, 1 x seal tape..

Direct fit for 2021 Ford Bronco with 2.7L EcoBoost. Pre-installed factory-style quick-disconnect fittings for clean installation. Direct-fit bracket mounts the catch can away from engine vibration. Sturdy 2.5mm-thick steel brackets withstand rough roads and off-road abuse. Helps prevent fuel dilution and preserve its octane rating.

Direct fit for 2020 Ford Explorer ST with 3.0L EcoBoost. Protects intake valves from power-robbing carbon buildup. Catch can captures blow-by, preventing it from fouling the engine oil. Patented billet 6061 aluminum can sealed with Viton O-rings. Mishimoto Lifetime Warranty.

Compatible with 2015-2017 Ford F-150 2.7L EcoBoost. Dual-can setup captures blow-by from both the PCV and CCV systems. CCV side accommodates stock pressure sensor for CEL-free running. In-line check valve prevents can from being pressurized under boost. Filters and can are fully serviceable.

Helps prevent intake related problems by keeping intake tract cleaner. Filtering consists of a fine mesh stainless steel filter that traps fine oil vapors and releases them once heavy enough to fall.. Plug-N-Play Installation, includes video instructions. Made in the USA. Knurled tank base for easy removal to drain the spent oil and an O-ring seal to prevent any leaks..

Direct fit for 2011-2014 Ford F-150 3.5L EcoBoost. Dual-can setup captures blow-by from both the PCV and CCV systems. Large 7.5 oz and 12 oz cans for longer service intervals. In-line check valve prevents can from being pressurized under boost.. Filters and cans are fully serviceable and comes with the Mishimoto Lifetime Warranty.

Compatible with2011-2021 F150 5.0L2011-2021 F150 5.0L with RoushWhipple superchargers2011-2021 F150 3.5L Ecoboost2015-2021 F150 2.7L Ecoboost2017-2021 Raptor 3.5L Ecoboost2018-2021 Expedition 3.5L EcoBoost.. Portable SeparatorThe maxed capacity of the tank is 400ml, compact size, easy to use and clean.After installing the valve, when it gets too full of oil, you just need to unscrew the valve to empty its contents without reinstalling and it could be reused constantly.. FeaturesOne inlet and one Exit Filter and can are both fully serviceable.Internal air diverter turbulates air longer to improve oil separation.. Multiangle InstallationThe top mounting braket of oil tank allows it to be mounted from multiple angles to fit for your car, package includes mounting hardware for your installation.. Lifetime WarrantyThe oil separator catch can kit from KET comes complete with a lifetime warranty.If there is any problem with the product,please contact us and we'll solve it for you immediately..

fit for Scat Pack Shaker 11-21. Anodized black, corrosion resistant. Made of high-quality aluminum alloy. 1 year warranty.

Fitment Compatible with 2011-2023 F150 5.0L, 2011-2023 F150 5.0L with RoushWhipple superchargers, 2011-2023 F150 3.5 Eco-Boost, 2015-2023 F150 2.7L Eco-Boost, 2017-2023 Raptor 3.5L Eco-Boost, 2018-2021 Expedition 3.5 Eco-Bost. Function Fine mesh aluminum filter traps fine oil vapors, helping to prolong the life of your engine and keep it running smoothly and cleanly. Installation Location In most cases, you will only need to install the air-oil separator on the PCV side of the engine. Comes with hoses, custom brackets and fittings needed for direct replacement. Includes installation instructions. NOTE It is recommended that the oil separator be checked after 500 to 1,000 miles to see if it needs to be cleaned.

Size Catch can capacity 750ml The thread size of 10an is 78-14 UNF Bottom drain valve thread is 38 NPT. 10AN fuel hose ID 0.5614.22mm OD 0.7819.8mm Length 10 feet.. Universal Oil catch can kit be applied to most cars. Please make sure you have enough space in your car before installation.. Material Oil catch can is made of aluminum alloy. Fuel line is made of CPE, stainless steel and nylon braid.. Parameter Working pressure 500PSI. Burst pressure 2000PSI. Operating temperature -40F to 257F. Minimum bending radius 101.6mm.. Feature A drain valve at the bottom of the oil catch can makes it easier to clean and reuse. Thread come with o-ring gasket to prevent oil leakage. For optimal performance, apply lubricating oil to the joint thread and tighten securely with a wrench..

Baffled Design Featuring a removable baffle and adding an appropriate amount of steel wool, this oil catch can effectively trap oil and moisture, preventing carbon buildup, keeping your engine's intake, valves, and pistons clean. It helps maintain optimal performance and extends engine lifespan.. Universal Fit With a 300 ml capacity, this catch can is compatible with most vehicles. Please ensure there is sufficient space for installation.. Durable NBR Fuel Hose Kit The kit includes a high-quality NBR Hose that is known for its exceptional wear and heat resistance. The hose length is 59 in 1.5 m, with an ID of 58 and an OD of 0.945. The inlet and outlet ports feature an M161.5 thread for a secure fit.. PCV System Compatibility Oil Catch Can with or without Breather Filter You can install it with a breather filter for pre-PCV cars as a vent system, or install it without a breather filter in line between PCV hoses as a sealed can.. Note In freezing temperatures, the crank vent system generates increased moisture, which may lead to freezing risks. To prevent blockages, clean the catch can weekly or reinstall the original hose in cold weather conditions..

Compatibility The oil catch can is compatible with 2011-2014 Ford Mustang 5.0L. Function The 130ml oil separator effectively captures oil vapor and contaminants. It helps extend engine life and keep it running smoothly and cleanly.. Precision Filtration Utilizes a fine mesh aluminum filter to capture even the smallest oil vapors, The rotating disassembly tank base for effortless take out and drainage of spent oil, while an integrated O-ring seal safeguards against leaks. Custom Mounting Fitment Designed with the engine layout in mind, they include required hose, custom brackets and aluminum quick connect fittings. This means installation is more easy, with less need for modifications or additional adapters. Including installation instructions. Note It is recommended to check whether the oil separator needs cleaning after driving 800 to 1600 miles. Due to the high sensitivity of the pressure sensor, the check engine light may trigger above 4000 ft elevation..

Compatibility The oil catch can is compatible with 2018-2023 Jeep Wrangler 2.0L. Function The 295ml oil separator effectively captures oil vapor and contaminants. It helps extend engine life and keep it running smoothly and cleanly.. Precision Filtration Utilizes a fine mesh aluminum filter to capture even the smallest oil vapors, The rotating disassembly tank base for effortless take out and drainage of spent oil, while an integrated O-ring seal safeguards against leaks.. Custom Mounting Fitment Designed with the engine layout in mind, they include required hose, custom brackets and aluminum quick connect fittings. This means installation is more easy, with less need for modifications or additional adapters. Including installation instructions.. Note It is recommended to check whether the oil separator needs cleaning after driving 800 to 1600 miles. Due to the high sensitivity of the pressure sensor, the check engine light may trigger above 4000 ft elevation..

knurled tank base for easy removal to drain the spent oil and an O-ring seal to prevent any leaks.. Filtering consists of a fine mesh stainless steel filter that traps fine oil vapors and releases them once heavy enough to fall.. The tank holds 3 oz of fluid, Check the oil separator after 1000 miles of. Most applications can make it 2500-3500 before filling the unit but every vehicle is different. Oil Separators.

Direct fit for 2021.5 Ford F-150 3.5L EcoBoost. Dual-can setup captures blow-by from both the PCV and CCV systems. Includes oversized 12 fl. oz. can for longer service intervals. CCV side accommodates stock pressure sensor for CEL-free running. Mishimoto Lifetime Warranty.

FitsOur oil catch can kit is compatible with 2014-2018 Chevy Silverado 1500 5.3L 6.2L, 2015-2020 Chevy Tahoe 5.3L 6.2L, 2015-2020 Chevy Suburban 5.3L 6.2L, compatible with 2014-2018 GMC Sierra 1500 5.3L 6.2L, compatible with 2015-2020 GMC YukonYukon XL 5.3L 6.2L, 2015-2019 Cadillac Escalade 6.2L.. FeatureMade of anodized aluminum, resistant to high temperature and pressure. Easy installation in 30 minutes.. FunctionInstall the oil catch can on the PCV side of your engine for efficient oil separation. The fine mesh aluminum filter captures fine oil vapor, helping to extend engine life and keep it running smoothly and cleanly.. InstallationEquipped with the required hoses, custom brackets and fittings for direct replacement.. TipsIt is recommended that the oil separator be checked after 500 1000 miles to see if it needs to be cleaned..

Compact Size The catch can has a small body,can save the pace in your engine. Universal Fittment The catch can can be used on many cars.Just make sure there is enough space in your engine to install it. Baffled Oil Catch Can Separates oil particles by using 50 micron bronze filter. Defends intercooler, intake system and essential components from oil blow-by.Helps maintain proper octane levels to reduce potential detonation.. Material The PQY oil catch can is made of 6061 aluminum with black coating,features M16 x 1.5 threads of inlet and outlet. Convinient The oil reservoir tank comes with a drain valve,which is convenient for you to empty the contents in the catch can without opening cap of the tank..

Keep Engine CleanThe baffle system in the tank could catch the oil and moisture from PCVCCV air, prevent misfires due to carbon accumulation, keep the engine clean, and prolongs engine life. Premium Quality Made of High Quailty Aluminum, durable and not easy to fade. Rust-resistant,scratch-resistant and corrosion-resistant. Make sure you use it for a long time. Big CapacityThe capacity of the tank is 750 ml about 25.3 oz, which is easy to clean and generally fit for most cars. Package Included 1x Oil Catch Can, 1x Breather Filter, 1x Drain Valve,1x Hose Clamp, 5x Hose connector. PURCHASE WITH CONFIDENCE Any questions please feel free to reach out to us, we will reply to you within 24 hours. Your satisfaction is fully guaranteed..

Plug n Play Installation - UPR Lifetime Warranty - All Catch Cans Ship Priority Mail and generally take 2 to 3 days from order date. Exclusive Continental Insta-Grip Braided Hoses w UPR Billet Fittings. UPR 3-Stage Oil Diffuser with Multi-Hex Coalescing media for the Best Oil Separation. Detailed Install directions included - Exclusive Self Tapping Machine Screw with Nuts - Made in the USA. Happy with your purchase, be sure to share installed images to be eligible for a FREE UPR T-Shirt. UPR Catch Cans are designed to be opened and closed with no effort. Overtightening will cause them to get stuck. When hard to open you overtightened it and need to use less effort and gently snug it closed..

FITMENTOil Separator Reservoir Tank compatible with Ford F-150 3.5L 2.7L2011-2021Expedition 3.5L2017-2021. WHY NEED ITThe Separator will keep out the dirt and oil get inside your engine from your intake system. To keep engine clean , Increases horsepower and Preserve Engine Life.. EASY INSTALLATIONEasy Plug Play installation,The oil catch can top mounting bracket allows mounting from multiple angles to fit your car, easy and convenient.. HOW DOES IT WORKDuring the process of venting crankcase pressure back through your intake track, large amounts of oil, in the form of vapors can gatheraccumulate in your intake tube, intake manifold runners and even dilute your gas, lowering its octane level.. PACKEG INCLUDEAluminum Tank1,812 Fitting1, M5 Nuts2, M520 Bolts2, M625 Bolts2, M6 U-shaped Spring Nuts2.