Direct Fit for Original. - Auger motor fits for Traeger grill models Traeger 070, 075, Texas Elite Series, Pro 22, Pro 34, Lil Tex Elite Series, Camp Chef smoker grill, Pit Boss Wood Pellet Grills EXCEPT PTG.. Auger Motor Feature - 2.0 RPM, 120V 60Hz 2 Pole comes with an auger pin for multi-models. This auger motor's main function is to generate power to push pellets into the fire pot.. Upgraded Auger Motor - Upgrade Auger Motor Wire, UL133218AWG PEP Material Special High Voltage and High-Temperature Resistance Wire. Make the Auger Motor More Durable and More Resistant to High Temperature.. Easy to Plug on - Remove the hopper, remove the burned-out or neglected motor, and install it as it was. Maintain Feed Tube - Clean out your auger tube. Blow it out with compressed air from the fire pot end, while the hopper is empty. It will prevent sawdust jams that kill auger motors.. When to Replace an Auger Motor - A Pellet Grills Auger Motor Keeps the Fuel Moving Into the Firepot. When Your Hardwood Pellets Wont Feed to The Fire, Please Replacement it. Charge Auger-Youll have to recharge the auger. Add a small amount of pellets to the hopper and throw a large handful on the igniter in the fire pit. the fire should ignite longer auger tubes take a while to charge. The controller will stop feeding pellets after five minutes if the fire is not lit. So turning off and back to smoke will reset the igniter sequence. When the auger is charged youll see pellets dropping into the fire pot..

England Pellet Stove PU-047040 Technical Specifications Volts 110V, Amps 1.03A, Cycles 60HZ, RPM 1, Direction Counter Clockwise. Wire Length 20 with 14 Male and Female Terminal, Gearbox Measures 2 34 Widex 4 58 High x 1 Width Width to screw mount hole 1 516, CCW1 Auger Motor x 2 Pack. England stove Replacement For Part Numbers PU-047040, 44269, B4415UI. Perfect Fit PU-047040 Auger Feed Motor Replacement for Englander 10-CPM, 25-CAB80, 25-PAF, 25-PDV, 25-PDVC, 25-PDVE, 25-PDVP, 25-PFS, 25-PI, 55-SHP22E, 49-SHCPM, 49-TRCPM, 55-SHPCAB80, 55-TRPCAB80, 55-SHP22, 55-TRP22, 55-SHP10, 55-SHP10L, 55-TRP10, 25-PFSP, 55-SHP25, 55-TRP25, 55-SHP15, 55-TRP15, 55-SHP20, 55-TRP20. Function Powerful The Englander auger motor is fully assembled, with built-in leads to connect to your existing furnace's wiring. The auger motor is securely mounted to the auger shaft and will have your furnace up and running in minutes. This auger motor is powerful, quiet, and rotates steadily.The Englander Replacement Auger Motor will keep your auger system running smoothly while keeping it warm during the cold winter months. EASY INSTALLATION To replace auger, remove all fuel from hopper and top auger assembly. Remove the four bolts that hold the bearings in place, then remove the auger assembly and use a wrench to loosen the two set screws to disconnect the bearings from the shaft. The bearing assembly and auger assembly can be replaced by reversing this process. Always tighten the four bolts diagonally when placing the auger assembly in the unit to ensure that the bearing and shaft are properly aligned. High-Quality Auger Motor 1 RPM PU-047040 provide both male and female spade connectors, depending on your stoves configuration. The CCW1 auger motor is made of quality stainless steel, durable material that can be applied for a long time. The auger motor turns the auger, which transfers thepellets from the hopper to the burn pot. lt feeds thefire and keeps the flame going. The auger motor mustbe replaced ifit slows down or skips under a load.

CU-047044 Motor Technical Specifications 110V, 60HZ, 1.28A, 4 RPM, sealed bearing motor, Clockwise rotation when facing the shaft, Our Pellethead PH-CW4 is a top quality replacement auger feed motor for Englander pellet stove models. This is a replacement for England stove Works factory part number CU-047044. Function Powerful Englander CU-047044 has powerful functions, guaranteed quality, and the installation process is very convenient, 4RPM auger motor for Englander corn stoves models 10-CDP, 10-CDV, 10-CDVG, 10-CDVL, 10-CDVP, 49-SHC22, 49-TRC22. Product Dimension 38 Diameter x 1 18 Length Shaft - Flat Edge of shaft for Securing with Set Collar, Wire leads measure 20 in length with 14 Male and Female Terminal. Gearbox Measures 2 34 Widex 4 58 High x 1 Width Width to screw mount hole 1 516, Total width including magnet, armature and gearbox measures 2 18. Highly functional The Englander auger motor is fully assembled, with built-in leads to connect to your existing furnace's wiring. The auger motor is securely mounted to the auger shaft and will have your furnace up and running in minutes. This auger motor is powerful, quiet, and rotates steadily.The Englander Replacement Auger Motor will keep your auger system running smoothly while keeping it warm during the cold winter months. High-Quality We include both male and female spade connectors depending on your stoves conhguration, CW4 auger motor is made of high quality stainless steel, durable for long term use.The auger motor turns the auger, which transfers thepellets from the hopper to the burn pot. lt feeds thefire and keeps the flame going. The auger motor mustbe replaced if it slows down or skips under a load.

Compatible with Traeger Pellet Grills This 17 Auger Shaft Push Rod and Auger Motor Bushing Replacement Parts are designed to fit for Traeger Pro 22, Lil Tex Elite 22, Eastwood 22, Fremont, Mesa 20 22, Professional, Lil' Pig, Longhorn Steer, Rolltop Renegade Elite 20. NOTE Measure your old auger kit size before purchasing to avoid wrong size fitting issues.. Compatible with Camp Chef Pellet Grills The 17 IN Auger Shaft Screw Kit fit for Camp Chef 24LS, 36ZD, SGX36 WIFI, SmokePro DLX 24, SmokePro LUX 36, SmokePro SE 24, SmokePro SG 24, SmokePro LUX 36, SmokePro SGX 36, SmokePro STX 24, SmokePro XT 24, Woodwind Classic 24, Woodwind SG 24, Woodwind WiFi 20, Woodwind WiFi 24, Woodwind WiFi 36, and XXL, Woodwind 24, Woodwind 36, Woodwind Pro 24, Woodwind Pro 36, for Camp Chef XX,PG36LUX PGVXXL. Functionality Grill Auger Shaft Screw kit paired with your Traeger auger motor, help you send the wood pellet to the Fire Burn Pot of your grill to burn. You can restore your grill's pellet feed efficiency with replace new Auger Shaft Screw, ensuring consistent heat and smoke distribution, get your grill back in top condition.. High-Quality Our Auger Shaft Screw is made of heavy-duty material for withstand long-term use without compromising performance, providing reliable and lasting functionality.. Easy Installation It is easy to replace, securely attach the screws, and properly fix the motor and auger kit before inserting it into the grill. Dimension auger motor bushing is 1.49 in outer diameter, 0.53 inside diameter and 1 in height, igniter auger shaft is 17 long. Package includes 1 x auger, 1 x Auger Motor Bushing nylon sleeve , 1 Set 74072 Auger Motor Shaft Nut Bolt..

Compatible ModelsSRV7000-670 Auger Feed Motor is calibrated to fit PelPro models PP60, PP60-B, PP60-RF, PP130, PP130-B, PP130-RF, PP70, PP150, PPC90, TSC90, as well as Pleasant Hearth models PH35PS, PH50PS, PH50CABPS, PHC90, and is compatible with Quadra-Fire Outfitter I II equivalents. The motor operates at 2 RPM in a dual-direction configuration CWCCW and ships with a 3-pin Molex pre-wired connector for easy installation and broad compatibility. Technical SpecificationsPower 120V, 60HzRPMDirection 2.0 RPM, CWCCWShaft Design drilled shaft with OEM-compliant and mounting hole spacingConnector 3-pin Molex pre-wired connector. Performance DurabilityA 2 RPM synchronous motor fireplace fans delivers stable and even fuel feed, supporting smooth ignition and sustained heat output for pellet stoves. High-quality materials and heat-resistant design enhance durability in high-temperature environments, reducing maintenance frequency and extending service life. Installation ReliabilityThis replacement part is a direct-fit installation, with a 3-pin Molex connector ensuring quick connection. Simple assembly suits both DIY homeowners and professional technicians. Pre-shipment testing includes extended run time 48 hours, load endurance, and voltage fluctuation tests to ensure reliability on arrival. Use Case ScenariosSuitable as a replacement part for PelPro, Pleasant H searth, and Quadra-Fire pellet stoves, helping maintain original performance and reduce downtime. OEM-grade replacement experience with easy installation and broad compatibility, ideal for replacing aging components and improving reliability. Wiring Safety and TroubleshootingThis dual-direction feed auger motor requires precise wiring1.White-Yellow CCW counterclockwise, smooth quiet 2.White-Black CW clockwise, stable performance 3. NEVER connect Yellow-Black causes severe vibration, noise, and motor burnout.Fix Power off immediately, restore correct wiring to eliminate issues.Always disconnect power before wiring changes to avoid shockdamage.

Compatible With CU-047042 Feed Auger Motor for Englander Models 10-CPM 49-SHCPM 49-SHCPML 49-TRCPM Pellet Utility Furnace Models with PUF in the model number Pellet Auxiliary Heater Models with PAH in the model number Evolution Pellet Models with EP in the model number Imperial Pellet Models with IP in model number. Stirrer Agitator Motor for Englander Turns the agitator bar in the fire pot CORN stove models 10-CDV 49-SHC22 49-TRC22.. Included With Purchase This aftermarket england pellet stove auger motor is a durable sealed ball bearing motor, the quality of this replacement motor is equal to the original motor. 1 Year Warranty from Date of Purchase.. Quiet Motor This cu-047042 auger motor 2rpm is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.. Keep Your Home Warm Our aftermarket englander 25 pah pellet stove auger motor will have your englander 25-pah auger system running smoothly while keeping you warm during the cold winter months.. Technical Specs 2 RPM, CLOCKWISE Rotation When Facing Shaft, 110 V, 60 HZ, 1.03 Amps, 38 Diameter x 1-18 Length Shaft, Flat Edge of Shaft for Securing with Set Collar..

Compatible With EF-001 auger motor for Enviro Mini, Mini-A, EF3, Meridian, EF2, Milan, P3, Empress FS, Empress FPI pellet stove models. Agitator Motor for Enviro M55, M55 Cast, M55 Cast Insert pellet stove models. AugerAgitator Motor for VistaFlame VF100, VF 100, VF55, VF 55, VF100 Insert pellet stove models. AugerAgitator Motor for Regency GF55, GCI60, GFI55, GC60, GF40 pellet stove models. Auger Motor for hudson river davenport, kinderhook pellet stove models.. Included with purchase This aftermarket enviro m55 pellet stove agitator motor is a durable sealed ball bearing motor, the quality of this replacement motor is equal to the original motor. 1 Year Warranty from Date of Purchase.. Quiet Motor This enviro m55 agitator motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.. Keep Your Home Warm Our aftermarket enviro auger motor ef-001 will have your enviro pellet stove auger system running smoothly while keeping you warm during the cold winter months.. Technical Specs 1 RPM, CLOCKWISE Rotation When Facing Shaft, 110 V, 60 HZ, 1.28 Amps, 38 Diameter x 1-18 Length Shaft, Flat Edge of Shaft for Securing with Set Collar..

Perfect Compatible Models Auger motor for Lennox Winslow PS40 PI40 pellet stove models. Auger motor for Whitfield Advantage 2, Advantage I, Advantage II, Advantage II-T, Advantage III, Advantage III Insert, Advantage II-T Classic, Advantage II-T Insert, Advantage Plus, Advantage Plus Insert, Advantage 1, Profile 30, Profile 30 Insert, Profile 20, Quest, Quest Insert, Quest Plus, Quest Plus Insert, Optima 3, Optima 2, Cascade, Traditions T300P, Waterford Erin pellet stove models.. What You Will GetThis aftermarket lennox winslow ps40 auger motor is a durable sealed ball bearing motor, the quality of this replacement motor is equal to the original motor. 1 Year Warranty from Date of Purchase.. QuietThis winslow ps40 pellet stove auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.. Keep Your Home WarmOur aftermarket winslow ps40 pellet stove auger motor will have your lennox winslow auger system running smoothly while keeping you warm during the cold winter months.. Technical Specs 1 RPM, CLOCKWISE Rotation When Facing Shaft 110 V, 60 HZ, 1.28 Amps 38 Diameter x 1-18 Length Shaft Flat Edge of Shaft for Securing with Set Collar..

80606 Auger Motor Specifications Volts 110V, Amps 1.03A, Cycles 60Hz, 1RPM, CLOCKWISE Rotation When Facing Shaft, Hole Drilled in Shaft to Spec, Wire Length 20 with 14 Male and Female Terminal, Flat Edge of Shaft for Securing with Set Collar, Replacement For Part Number 80606. Widely Compatible Quality Sealed Bearing Replacement 1 RPM Auger Motor for US Stove, USSC, Ashley pellet stove models Compatible with US Stove 5660, Bay Front 5660, 5660E, USSC 5660, 5560, APS5660 Pellet Stoves 80606 Auger Motor Compatible with Ashley AP5660 AP5660L AP5660PE Pellet Stoves. Easy to Install ashley 80606 auger motor comes fully assembled is easy to install, we provide both male and female spade connectors, depending on your stoves configuration, 80606 auger motor is made of stainless steel, durable material that can be applied for a long time, Pellet stove operation can be kept efficient by replacing the auger motor. Powerful Functionality The auger motor's function is to manage the rate at which the pellets go through into the combustion compartment, which aids in maintaining the desired level of heat output and regulating temperature 1 RPM auger motor is designed to provide reliable, efficient performance to ensure your heating system runs smoothly and effectively. Quiet Operation 80606 Auger Motor is a durable sealed ball bearing motor, the quality of the replacement motor is equal to the original motor, safe and reliable to use, This upgraded motor has enough oil between the internal gears, so the gears rotate without making loud noise and rotate stably.

England Stove Works Auger Motor - Correct Replacement for Top and Bottom motor. 1RPM 110 V, 60 HZ, 1.03 Amps. Improved Easy Install with 12 Wire Leads. Full 1 Year Warranty. Free Fast Shipping - Guaranteed Best Price.

Why Need A Auger Motor - This c-e-017 auger motor's function is to manage the rate at which the pellets go through into the combustion chamber, which aids in maintaining the desired level of heat output and regulating temperature. This process will allow the stove to maintain a consistent temperature in the room by adjusting the auger motor according to changes in the ambient temperature.. Premium Performance - The breckwell auger motor c-e-017 is made of high-quality material, and each motor examnines before leaving factory and strict testing, to ensure a good structure, excellent suction, perfect matching and smooth operation, ensuring that you receive good motor replacement.. Quiet Operation - Upgraded this breckwell auger motor 80642 c-e-017 minimizing noise levels. The auger motor's shaft rotates clockwise and powers the agitator shaft to mix the pellets. A cotter pin mounting hole has been drilled in the shaft, and wire leads are already attached. Easy installation and maintenance. If your unit needs different femalemale spade clips, these can be removed and changed out.. Parameter of C-E-017 Auger Motor - 110V, 60 HZ, 1.03 Amps, 1 RPM Clockwise With Hole. Size 38'' Diameter x 1 18 Length Shaft Flat Edge of Shaft. Wire leads measure 20 12'' in length. Replaces Part Numbers - Breckwell Auger Motor 80642 C-E-017. Fit For US Stove Pellet Stoves Parts Models - 5040 Fit For Ashley Pellet Stoves Parts Models - APC4000.. Fit For Breckwell Pellet Stoves Parts Models - P22 Maverick, P22I Maverick Insert, P23 Sonora - Serial 7166 to Present, and Units BEFORE serial 6332, P23I Sonora Insert - Serial 2243 to Present, and Units BEFORE serial 1916, P24 Blazer - Serial 53664 to Present, P24I Blazer Insert - Serial 53795 to Present, P1000 Big E, P2000 Tahoe - Serial 11780 - Present, P2000I Tahoe Insert - Serial 22208 - Present, P2700 Mojave - Serial 8445 - Present, P4000 Classic Cast..

SPECIFICATIONSReplace Part Number PU-076002B Volts 115 Cycles 60 Hz Amps 0.9 Rpms 3000. COMPATIBILITY1The PU-076002B Combustion Exhaust Blower Fan is compatible with Englander 25-PAF, 55-SHP25, 55-TRP25 25-PAH, 55-SHPAH, 55-TRPAH 25-PDV, 55-SHP22, 55-TRP22 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10 25-PDVE, 55-SHP22E 25-PDVP, 55-SHP15, 55-TRP15 25-PI, 55-SHP20, 55-TRP20 25-SSP01, 55-SHSSP01, 55-TRSSP01 25-PFS, 25-PFSP Pellet Stoves. COMPATIBILITY2The PU-076002B Combustion Exhaust Blower Fan is compatible with Englander 10-CDV, 49-SHC22, 49-TRC22 25-CAB80, 55-SHPCAB80, 55-TRPCAB80 25-CB120, 55-SHPCB120, 55-TRPCB120 25-CBEP, 55-SHPCBEP, 55-TRPCBEP 25-CBPAH, 55-SHPCBPAH, 55-TRPCBPAH 25-EP, 55-SHPEP, 55-TRPEP 25-EPI, 55-SHPEPI, 55-TRPEPI 25-IP, 55-SHPIP, 55-TRPIP Pellet Stoves. DURABLE EFFICIENT PERFORMANCECrafted with premium materials and tested for long-term durability, this combustion exhaust blower fan delivers strong, consistent airflow to help effectively expel combustion gases and heat. Designed to reduce the risk of system overheating, minimize safety alarms, and improve heat outputan ideal upgrade for enhanced performance and peace of mind. ONE YEAR QUALITY ASSURANCEIf the product has any quality problems within one year, please contact us.

Compatibility Auger Feed Motor Replacement for PelPro PP60, PP60-B, PP70, PP130, PP130-B, PP150, PPC90, TSC90 Pellet Stoves. Compatibility Agitator Motor For Pleasant Hearth PH35PS, PH50CABPS, PH50PS, PHC90 Pellet Stoves. Replace Part Number SRV7000-670. Upgrade Quality SRV7000-670 motor with pure copper motor, it features powerful performance, greater energy efficiency, better conductivity, runs smoothly, quite working, longer service life. Perfect Replacement Auger motor highly suitable for replacing faulty parts or upgrading old ones, with a perfect match and being more cost-effective. Specification Voltage 120 V , Cycles 60 Hz, RPM 2.0, Direction Clockwise Counterclockwise.

The Quadrafire 1000 Auger Motor Technical Specifications Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise. Wire Length 20 with Male and Female Terminal. CCW1 Auger Motor.. Compatibility Replacement 812-0170 Auger Feed Motor for Quadra-Fire 800 1000 Pellet Stove.. Replacement For Part NumberQuadra-fire 812-0170.High Quality Auger MotorPowerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. Easy to installThe 1RPM Quadra-Fire 1000 FS auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration.. High-qualityThe CCW1 auger motor is made of quality steel, durable material that can be applied for a long time..

The US Stove 80488 Auger Motor Technical Specifications Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise. Wire Length 20 with Male and Female Terminal.. Perfect Compatible Models Auger Motor for Vogelzang VG5790, 5790, VG5770, 5770, VG130 pellet stoves. 80488 AugerAgitator Motor for American Harvest 6039, 6041, 6500, 6100, 6037, 6033, 6039T, 6035, 6039HF, 6039I, 6041HF, 6041I, 6041TP, 6200, 6220 pellet stoves.. Perfect Compatible Models 80488 Auger Motor for AshleyKing 5500M, 5502M, KP130, AP5710, 5500, 5510, 5500XL, AP5780, AP5790, APC1406 pellet stoves. AugerAgitator Motor 80488 for US Stove 6041, 6039, 5500M, 8500, 5500, 5502M, 5520, 6041I, 5510, 6100, 6041HF pellet stoves.. Perfect Compatible Models 80488 AugerAgitator Motor for USSC 6039, 6041, 5500M, 6100, 5510, 8500, 6041I, 6041TP, 5500, 6039T, 6500 pellet stoves. Auger Motor for Breckwell SP6000 heartland multi-fuel, SP1002 big e ll, SP8500 pellet stoves.. High-quality Easy to installThe 1RPM auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CCW1H auger motor is made of quality stainless steel, durable material that can be applied for a long time.

Whitfield-quest, breckwell, Travis Avalon lopi, Quadra-fire, fasco 7021-9129. Fan 4.75 diameter, mounting plate 5.75, bolt hole centers 5 38. Shaft 516 x 1 78, rotation cw facing shaft, sleeve bearings. 3.3 diameter motor, includes gasket, fan blade plug. Motor case length 3.5, one year warranty.

Compatibility --- Replacement SRV7000-670 auger feed motor for PelPro PP60, PP60-B, PP70, PP130, PP130-B, PP150, PPC90,TSC90 pellet stove.. Compatibility --- Replacement SRV7000-670 auger feed motor for Pleasant Hearth PH35PS, PH50CABPS, PH50PS, PHC90 pellet stove.. The PelPro PP130 Auger Feed Motor Technical Specifications --- Volts 120V AC, Cycles 60 Hz, RPM 2, DirectionCW or CCW, Connector3 Pin Molex. Original parts number SRV7000-670. High Quality --- The PelPro Pleasant Hearth Auger Feed Motor is made of high quality materials, which is better than OEM standards. Every motor has been examnined before leaving factory, and each one has been tested before shipping too, it will ensure that you will get good motor replacement.. Great Customer Service --- We are professional pellet stove motor seller, and offer one year warranty for the PelPro PP130 auger motor. Whether you encounter any problems before or after the purchase, you can contact us directly..

The Whitfield Auger Motor Technical Specifications --- Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Clockwise. Wire Length 20 with Male and Female Terminal. CW1 Auger Motor.. Compatibility --- Replacement 12046300 Auger Motor for Whitfield Advantage IIIII-TIII WP2, Advantage Plus WP7, Cascade WP5, Explorer WF1, Frontiersman WF2, Legend WP1, Optima 2 A02, Optima 3 A03, Prodigy I II WP3, Quest WP4, Quest Plus WP4, Profile 20 P9 7495 - 7494, Profile 30 P10 11905 - 11904, Renaissance WW1, Waterford Erin, Traditions T300P, T301P, T305P, T308P, TP300, TP340.. Compatibility --- Replacement H5886 Auger Motor for Lennox PS40 Winslow FS, PI40 Winslow Insert, PS32 Montage Pellet Stoves.. Replacement For Part Number Lennox H5886, Whitfield 12026300 12046300. High Quality Auger Motor Powerful, Quiet, Energy Efficient and Long Lasting.. High-quality Easy to install --- The 1RPM Whitfield Advantage auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CW1 auger motor is made of quality stainless steel, durable material that can be applied for a long time..

Compatible With 3-20-60906 Auger Feed Motor Replacement for Harman P68, P43, P61, P38, Accentra 52i, P35i Pellet Insert, Accentra Insert, P61A , PC45, PF100 Furnace, DVC-500, Magnum Stoker, PC 45, Invincible RS, P38, Invincible Insert, PF120, PP38, Accentra 52i TC, DVC500, Pellet Pro II PP2, P61C, Invincible T Pellet and Coal Stoves. Included With Purchase This aftermarket harman auger feed motor 4rpm cw 3-20-60906 is a durable sealed ball bearing motor, the quality of this replacement motor is equal to the original motor. 1 Year Warranty from Date of Purchase.. Quiet Motor This aftermarket harman pellet stove auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.. Keep Your Home Warm Our aftermarket harman p61a auger motor will have your harman p61a auger system running smoothly while keeping you warm during the cold winter months.. Technical Specs 4 RPM, CLOCKWISE Rotation When Facing Shaft 110 V, 60 HZ, 1.28 Amps 38 Diameter x 1-18 Length Shaft Flat Edge of Shaft for Securing with Set Collar..

Perfect Compatible ModelsReplacement PU-076002B combustion exhaust blower for Englander 25-PDVC, 25-PDV, 55-SHP10, 25-PAH, 25PDVC, 55-SHP22, 25-EP, 55SHP22, 55-TRP22, 25EP, 55-SHPCB120, 25-CB120, 25PDV, 25-PDVP, 25-EPI, 55-SHP10L, 25PDVP Pellet Stove models. Replacement PU-076002B combustion blower for EnglanderEngland 10-CDV, 10-CDVG, 10-CDVL, 10-CDVP, 25-CAB80, 25-CAB80S, 25-CBEP, 25-CBPAH, 25-IP, 25-IPM, 25-IPS, 25-P, 25-PDVE, 25-PI, 25-SSP01, 25-PAF, 55-SHSSP01 55-TRSSP01 Pellet Stoves. Replacement PU076002B combustion exhaust blower for Englander England 49-SHC22, 49-SHC22G, 49-SHC22L, 49-SHC22P, 49-TRC22, 49-TRC22G,49-TRC22L, 49-TRC22P, 55-SHP15, 55-SHP20, 55-SHP22E, 55-SHP22L, 55-SHP25, 55-SHPAH, 55-SHPAHL, 55-SHPCAB80, 55-SHPCBEP, 55-SHPCBPAH, 55-SHPEPI, 55-SHPEPIL, 55-SHPEP, 55-SHPEPL, 55-SHPIP, 55-SHPIPL, 55-SHPIPM, 55-SHPIPS, 55-TRP10, 55-TRP15, 55-TRP20, 55-TRP25, 55-TRPAH, 55-TRPCAB80, 55-TRPCB120, 55-TRPCBEP, 55-TRPCBPAH, 55-TRPEPI, 55-TRPEP Pellet Stoves. Why Do You Need To Replace A New BlowerThe old englander 25-pdvc55-shp10 blower starts to make an unbearable metal-on-metal screeching noise, and your pellets don't burn out completely, wasting your money. The new combustion blower pu-076002b is a 100 improvement, this 25 pdvc combustion blower will have your Englander pellet stove running better and quieter, more even flame in pot, burns hotter and cleaner, saving you time and money on your heating costs. Save you from cold winter. Included With PurchaseThis aftermarket englander combustion blower pu-076002b-amp comes with everything you need for installation, includes exhaust fan motor with housing 2 piece gaskets motor gasket and housing gasket, also includes two extra female wire leads that make installation a breeze. Exclusive 1 Year warranty with our no hassle replacement guarantee.. Technical SpecsVolts 115, Cycles 60 Hz, Amps 0.94A, Rpms 3000, Clockwise Rotation While facing shaft. Sealed Ball Bearing Motor. 12 Fin Impeller, Fan Paddle 4-34 Diameter x 14 Tall. Housing Outlet Diameter 3.00 Standard.

Perfect Compatible Models Auger Motor for Vogelzang VG5790, 5790, VG5770, 5770, VG130 pellet stoves. 80488 AugerAgitator Motor for American Harvest 6039, 6041, 6500, 6100, 6037, 6033, 6039T, 6035, 6039HF, 6039I, 6041HF, 6041I, 6041TP, 6200, 6220 pellet stoves.. Perfect Compatible Models 80488 Auger Motor for AshleyKing 5500M, 5502M, KP130, AP5710, 5500, 5510, 5500XL, AP5780, AP5790, APC1406 pellet stoves. AugerAgitator Motor 80488 for US Stove 6041, 6039, 5500M, 8500, 5500, 5502M, 5520, 6041I, 5510, 6100, 6041HF pellet stoves.. Perfect Compatible Models 80488 AugerAgitator Motor for USSC 6039, 6041, 5500M, 6100, 5510, 8500, 6041I, 6041TP, 5500, 6039T, 6500 pellet stoves. Auger Motor for Breckwell SP6000 heartland multi-fuel, SP1002 big e ll, SP8500 pellet stoves.. What You Will Get This 80488 auger motor has 20 in length wire leads, also includes both male and female spade connectors depending on your stoves configuration. 1 Year Warranty from Date of Purchase.. Technical Specs 1 RPM, COUNTER CLOCKWISE Rotation When Facing Shaft Hole drilled in shaft to spec 110 V, 60 HZ, 1.03 Amps 38 Diameter x 1-18 Length Shaft Flat Edge of Shaft for Securing with Set Collar..

Compatibility Combustion Exhaust Blower Fan Replacement for Englander Pellet Stoves 10-CDV, 10-CDVG,10-CDVL, 10-CDVP, 49-SHC22, 49-SHC22P, 49-SHC22G, 49-SHC22L, 49-TRC22,49-TRC22G, 49-TRC22L, 49-TRC22P, 25-CAB80, 25-CB120, 25-CBEP, 25-CBPAH, 25-EP, 25-EPI, 25-IP, 25-PAH, 25-PDV, 25-PDVC, 25-PDVE, 25-PDVP, 25-PI, 25-SSP01, 25-PAF, 25-IPM, 25-IPS.Replacement part number PU-076002B. Compatibility Combustion Blower Fan Replacement for Englander Pellet Stoves 55-SHP10, 55-SHP10L, 55-SHP15, 55-SHP20, 55-SHP22, 55-SHP22E, 55-SHP25, 55-SHPAH, 55-SHPCAB80, 55-SHPCB120, 55-SHPCBEP, 55-SHPCBPAH, 55-SHPEP, 55-SHPEPI, 55-SHPIP, 55-TRP10, 55-TRP15, 55-TRP20, 55-TRP22, 55-TRP25, 55-TRPAH, 55-TRPCAB80, 55-TRPCB120, 55-TRPCBEP, 55-TRPCBPAH, 55-TRPEP, 55-TRPEPI, 55-TRPIP, 55-SHP22L, 55-SHPAHL, 55-SHPEPIL, 55-SHPEPL, 55-SHPIPL, 55-SHPIPM, 55-SHPIPS, 55-SHSSP01, 55-TRSSP01. Upgrade Quality Combustion blower with pure copper motor, it features powerful performance, greater energy efficiency, better conductivity, longer service life. Blower motor highly suitable for replacing faulty parts or upgrading old ones, with a perfect match and being more cost-effective. Working Quite High quality bearing motor have UL certification, runs smoothly, reduced vibration and noise,bringing you a quieter and more comfortable experience.Specification Voltage 115 V, Amps 0.94 A, Cycles 60 Hz, RPM 3000. Great Performance PU-076002B combustion blower motor provides a stable forced air flow to maintain efficient and stable combustion. Make the distribution of hot air more evenoptimizing combustion efficiency.

Perfect Compatible Models Replacement PU-076002B combustion exhaust blower motor for Englander 25-PDVC, 25-PDV, 55-SHP10, 25-PAH, 25PDVC, 55-SHP22, 25-EP, 55SHP22, 55-TRP22, 25EP, 55-SHPCB120, 25-CB120, 25PDV, 25-PDVP, 25-EPI, 55-SHP10L, 25PDVP Pellet Stove models. Replacement PU-076002B combustion blower motor for EnglanderEngland Pellet Stove model 10-CDV, 10-CDVG, 10-CDVL, 10-CDVP, 25-CAB80, 25-CAB80S, 25-CBEP, 25-CBPAH, 25-IP, 25-IPM, 25-IPS, 25-P, 25-PDVE, 25-PI, 25-SSP01. Replacement PU-076002B combustion exhaust blower motor for Englander England 49-SHC22, 49-SHC22G, 49-SHC22L, 49-SHC22P, 49-TRC22, 49-TRC22G,49-TRC22L, 49-TRC22P, 55-SHP15, 55-SHP20, 55-SHP22E, 55-SHP22L, 55-SHP25, 55-SHPAH, 55-SHPAHL, 55-SHPCAB80, 55-SHPCBEP, 55-SHPCBPAH, 55-SHPEPI, 55-SHPEPIL, 55-SHPEP, 55-SHPEPL, 55-SHPIP, 55-SHPIPL, 55-SHPIPM, 55-SHPIPS, 55-TRP10, 55-TRP15, 55-TRP20, 55-TRP25, 55-TRPAH, 55-TRPCAB80, 55-TRPCB120, 55-TRPCBEP, 55-TRPCBPAH, 55-TRPEPI, 55-TRPEP Pellet Stoves. Why Do You Need To Replace A New Blower Motor The old 25-pdvc55-shp10 blower motor starts to make an unbearable metal-on-metal screeching noise, and your pellets don't burn out completely, wasting your money. The new motor is a 100 improvement, this 25 pdvc Combustion blower will have your Englander stove running better and quieter, more even flame in pot, burns hotter and cleaner, saving you time and money on your heating costs. Save you from cold winter. Included With Purchase This 25-pdvc55-shp10 exhaust blower comes with everything you need for installation, includes new fan paddle, premium sealed ball bearing motor, 6 round gasket, also include extra female wire leads that make installation a breeze. Exclusive 1 Year warranty with our no hassle replacement guarantee.. Technical Specs Volts 115, Cycles 60 Hz, Amps 0.94A, Rpms 3000, Clockwise Rotation While facing shaft. Sealed Ball Bearing Motor. 12 Fin Impeller, Fan Paddle 4-34 Diameter x 14 Tall..

Compatibility-- Replacement PU-076002B Combustion Exhaust Blower Fan for Englander Pellet Stove 10-CDV, 25-CAB80, 25-CB120, 25-CBEP, 25-CBPAH, 25-EP 25-EPI Evolution Pellet, 25-IP Imperial Pellet, 25-PAF, 25-PAH Pellet Auxiliary Heater, 25-PDV, 25-PDVC, 25-PDVE, 25-PDVP, 25-PFS, 25-PFSP, 25-PI, 25-SSP01, 49-SHC22, 49-TRC22 Models.. Compatibility-- Replacement PU-076002B Combustion Exhaust Blower Fan for Englander Pellet Stove 55-SHP10, 55-SHP10L, 55-SHP15, 55-SHP20, 55-SHP22, 55-SHP22E, 55-SHP25, 55-SHPAH, 55-SHPCAB80, 55-SHPCB120, 55-SHPCBEP, 55-SHPCBPAH, 55-SHPEP, 55-SHPEPI, 55-SHPIP, 55-SHSSP01, 55-TRP10, 55-TRP15, 55-TRP20, 55-TRP22, 55-TRP25, 55-TRPAH, 55-TRPCAB80, 55-TRPCB120, 55-TRPCBEP, 55-TRPCBPAH, 55-TRPEP, 55-TRPEPI, 55-TRPIP, 55-TRSSP01 Models.. The PU-076002B Exhaust Blower Motor Technical Specifications--Volts 115, Cycles 60 Hz, Amps 0.94, RPM 3000. High Quality Bearing Motor--UL Certified, Powerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. The Criditpid PU-076002B combustion exhaust blower delivers a steady stream of forced air negative draft through the stove in order to keep the flame burning, while allowing you to set your heat range to your desired comfort level.. Our 25-PDVC55-SHP10 exhaust blower kit includes the combustion blower motor, 6 round gasket for the motor to the housing, 6 adapter plate, and 4-34 deep-lug fan paddle impeller blade. You will utilize your existing combustion blower housing with this kit which provides a significant cost savings. Easy installation for the specified Englander models replacing part PU-076002B..

The Englander PU-047040 Auger Motor Specifications Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise. Wire Length 20 with Male and Female Terminal. CCW1 Auger Motor.. CompatibilityReplacement PU-047040 Auger Feed Motor for Englander 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10 25-PDV, 55-SHP22, 55-TRP22 10-CPM, 49-SHCPM, 49-TRCPM 25-CAB80, 55-SHPCAB80, 55-TRPCAB80 Pellet Stove.. CompatibilityReplacement PU-047040 Auger Feed Motor for Englander 25-PAF, 55-SHP25, 55-TRP25 25-PDVE, 55-SHP22E 25-PDVP, 55-SHP15, 55-TRP15 25-PFS, 25-PFSP 25-PI, 55-SHP20, 55-TRP20 Pellet Stove.. High Quality MotorThe England pu-047040 auger motor mounts securely to the auger shaft and will have your stove up and running in minutes.This auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.. High-quality Easy to installThe 1RPM Englander 25-PDVC auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CCW1 auger motor is made of quality stainless steel, durable material that can be applied for a long time..

Auger Motor KS-5010-1010 Specifications Volts 110V, Amps 1.03A, Cycles 60Hz, 2RPM, Direction Clockwise, Wire Length 20 with 14 Male and Female Terminal, CW2 Auger Motor, Replacement For Part Number KS-5010-1010 Fit Sterling, Royce, Globe, Pel Pro, Pel Pro II. Widely Compatible Auger Motor KS-5010-1010 Fit Glowboy pellet stove models Bay View Freestanding, Bay View Insert, Classic FS, Classic INS, FBG Step Top, FGB Bay View, IGB Bay View, Home Heater HGBH1, Home Heater 120, Home Heater 300 HGBH3, Shop Heater, Shop Heater 120 HGB1, Shop Heater 300 HGB3 Fit PelPro pellet stove models PP300, Home Heater 300 HHPP32BD, Step Top FPP Fit Cheap Charlie pellet stove models Franklin 120 HCF120, Franklin 300 HCF300, Edison Junior HCJ, Edison Sr HCS. Easy to install The 2RPM Glow Boy KS-5010-1010 auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CW2 auger motor is made of stainless steel, The durable material is a good replacement. Ideal Choice This 2 RPM auger motor is designed to provide reliable, efficient performance to ensure your heating system runs smoothly and effectively, with its durable construction, reliable performance, this auger motor is the Ideal choice for replacing your auger motor. Quiet Operation Auger Feed Motor KS-5010-1010 is a durable sealed ball bearing motor, the quality of the replacement motor is equal to the original motor, safe and reliable to use, This upgraded motor has enough oil between the internal gears, so the gears rotate without making loud noise and rotate stably.

Compatibility PU-047040 Auger Feed Motor Replacement for Englander 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10 25-PDV, 55-SHP22, 55-TRP22 10-CPM, 49-SHCPM, 49-TRCPM 25-CAB80, 55-SHPCAB80, 55-TRPCAB80 Pellet Stove. Compatibility PU-047040 Auger Feed Motor Replacement for Englander 25-PAF, 55-SHP25, 55-TRP25 25-PDVE, 55-SHP22E 25-PDVP, 55-SHP15, 55-TRP15 25-PFS, 25-PFSP 25-PI, 55-SHP20, 55-TRP20 Pellet Stove. Upgrade Quality PU-047040 motor with pure copper motor, it features powerful performance, greater energy efficiency, better conductivity, runs smoothly, longer service life.Auger motor highly suitable for replacing faulty parts or upgrading old ones, with a perfect match and being more cost-effective. Flexible installation The auger motor is equipped with a 20-inch wire and provides male and female connectors, which can be removed and replaced according to your stove configuration. Specification Voltage 110 V Amps 1.03A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise.

The Englander Wood Stove Convection Blower Technical Specifications Volts 115 V, Cycles 60 Hz, Amps 0.8 A, Rpms 3000 RPM, Wire Length 90 with Triangle plug. Replacement For Part NumbersAC-16.. High Quality Bearing MotorUL Certified, Powerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. CompatibilityThe AC-16 Convection Blower Replacement Parts for Englander 10-CDV, 12-FP, 13-NC, 13-NCI, 15-SSW01, 15-SSW02, 17-VL, 18-MH, 18-TR, 24-ACD, 24-ICD, 24-JC, 27-C2000, 27-C3000, 30-NC Stove.. Adjustable speedThe Englander AC-16 variable speed blower with 3 position switch Off, Low, High. Evens heat flow throughout your heating area by circulating warm air over your stove and around your room.. BenefitsReplaces worn, damaged or noisy blowers, The Englander AC-16 Convection Blower Helps reduce costly energy bills, Heats large rooms efficiently, Installs quickly and easily, Affordable..

The Englander PU-047040 Auger Motor Specifications Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise. Wire Length 20 with Male and Female Terminal. CCW1 Auger Motor x 2 Pack.. Compatibility PU-047040 Auger Feed Motor Replacement for Englander 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10 25-PDV, 55-SHP22, 55-TRP22 10-CPM, 49-SHCPM, 49-TRCPM 25-CAB80, 55-SHPCAB80, 55-TRPCAB80 Pellet Stove.. Compatibility PU-047040 Auger Feed Motor Replacement for Englander 25-PAF, 55-SHP25, 55-TRP25 25-PDVE, 55-SHP22E 25-PDVP, 55-SHP15, 55-TRP15 25-PFS, 25-PFSP 25-PI, 55-SHP20, 55-TRP20 Pellet Stove.. High Quality MotorThe pu-047040 auger motor mounts securely to the auger shaft and will have your stove up and running in minutes.This auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.. High-quality Easy to installThe 1RPM Englander 25-PDVC auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CCW1 auger motor is made of quality stainless steel, durable material that can be applied for a long time..

CompatibilityWorks with England Stove Works, Summers Heat, and Timber Ridge Ideal for Englander pellet stoves and multi-fuel models.. Sturdy MotorSimple to set up with the built-in plug n play 12 wire connectors. Improved from the original, Stanbroil auger motor runs cooler with no rear plastic cooling fan required. 1-year warranty.. Specification1.2 RPM. 120 V, 60 HZ, 1.03 Amps. 38 Diameter x 1 Length Shaft. Flat Edge of Shaft for Securing with Set Collar. Wire leads measure 12 in length.. Energy EfficientWorks with top and bottom auger feed motors and installs in minutes. Mounts securely to the auger shaft and will have your stove up and running in minutes. Provides a steady rotation that allows for an even distribution of fuel.. Fits Models25-PDV, 25-PDVC, 25-PI, 25-PAF, 25-PDVP, 55-SHP10, 55-SHP10L, 55-SHP20, 55-TRP10, 55-SHP22, 55-SHP22L, 55-TRP15, 55-TRP22, SHP25, 55-TRP2, American Heritage, American Standard, US 25-5670. NOTE Correct replacement for the upper and lower augerdrive motors in the above-mentioned models..

Perfect Compatible Models Auger feed motor 812-4421 for QuadrafireQuadra-Fire Castile, Castile-C, Castile Freestanding Castile FS, Castile-FS-B, Castile FS MBK, Castile Insert, Castile Insert-B, Castile Insert-C, Classic Bay 1200 Freestanding CB1200FS, Classic Bay 1200 Insert CB1200i, Classic Bay 1200i Insert, Santa-Fe, Santa Fe B, Santa-Fe-C, Santa Fe-C INS, Santa Fe Freestanding Santa Fe FS, Santa-Fe-MBK, Santa Fe Insert pellet stoves.. Perfect Compatible Models 812-4421 auger feed motor for QuadrafireQuadra-Fire MT Vernon, MT Vernon E2, MT Vernon E2 FS, MT Vernon E2 Insert MT Vernon E2i, MT Vernon OE, MTV-E2-C, CB1200, CB1200-C, CB1200M-MBK, Trekker, Trekker Insert, Contour, CAB50-C pellet stoves. Auger motor for Heatilator CAB50, PS50, PS35, PS35-C pellet stoves.. What You Will Get This aftermarket quadra fire pellet stove auger motor includes the motor, mounting bracket and wire adapter, that will replace factory part number 812-4421 812-4420. 1 Year Warranty from Date of Purchase.. High Quality Motor Our aftermarket quadrafire auger motor replacement is a sealed bearing motor with all specifications matching exactly to the original factory motor, which is Quiet, Strong Sturdy.. Technical Specs RPM 2.4, Direction Normally Clockwise Rotation CW, Volts 120, Cycles 60 Hz, Watts 6, Shaft , Connector 3 Pin Molex..

Compatibility 3-20-60906 Auger Feeder Gear Motor Replacement For P35i Pellet Insert, P35i-C, P38 Post 008080066, P38, PP38, P43, P43-C, P61 Post 008085055, P61-C Post 008085803, P61A Post 008085803, P68 Pre serial 008280309, PC45, Pellet Pro II, PF100 Furnace Pre serial 008350087, PF120. Compatibility4 RPM Clockwise Auger Motor For Harman Pellet Stoves Accentra 52i, 52i TC, Accentra Insert, Invincible Insert, Invincible RS, Invincible T. For Harman Coal Stoves DVC-500, Super Magnum Stoker.Replacement Part Number 3-20-60906. Upgrade Quality 32060906 motor with pure copper motor, it features powerful performance, greater energy efficiency, better conductivity, runs smoothly, longer service life.Auger motor highly suitable for replacing faulty parts or upgrading old ones, with a perfect match and being more cost-effective. Flexible installation The auger motor is equipped with a 20-inch wire and provides male and female connectors, which can be removed and replaced according to your stove configuration. Specification Voltage 110 V, Amps 1.28 A, Cycles 60 Hz, RPM 4.0, Direction Clockwise.

Compatibility --- 3-20-60906 auger motor Replacement for Harman pellet stove Accentra 52i, Accentra 52i TC, Accentra Insert, Invincible Insert, Invincible RS, Invincible T, P35i, P35i-C, P38, P43, P43-C, PC45, Pellet Pro II, PF100, PF120 Models.. Compatibility --- 3-20-60906 auger motor Replacement for Harman pellet stove P38 Post 008080066, P61 Post 008085055, P61-C Post 008085803, P61A Post 008085803, P68 Pre 008280309.. Compatibility --- 4 RPM Clockwise Auger Motor for Harman wood coal stove DVC-500, Super Magnum Stoker. High Quality Auger Motor Powerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. The 3-20-60906 Auger Motor Technical Specifications --- Volts 120V AC, Amps 0.72 A, Cycles 60 Hz, RPM 4.0, Direction Clockwise. Wire Length 20 with Male and Female Terminal. AMP-CW4 Auger Motor.. High-quality Easy to install --- The Harman 4RPM auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CW4 auger motor is made of quality stainless steel, durable material that can be applied for a long time.

Compatibility Replacement 80488 auger motor for Vogelzang VG5790, VG5770, VG130 pellet stove. 1 RPM Counter Clockwise Auger Motor for AshleyKing pellet stove 5500, 5500M, 5500XL, 5500XLT, 5502M, 5510, AP130, AP5710, AP5770, AP5780, AP5790, APC1406, APCI1406, KP130 Models.. Compatibility Replacement king kp130 pellet stove auger motor for US Stove USSC 5500, 5500M, 5500XL, 5502M, 5520, 8500 Multi-Fuel, American Harvest 6033, 6035, 6037, 6039, 6039HF, 6039i, 6039T, 6041, 6041HF, 6041i, 6041TP, 6100, 6200, 6220, 6500 pellet stove.. Compatibility Replacement kp130 auger motor for Breckwell SP1002 Big E ll, SP6000 Heartland Multi-Fuel, SP8500 Multi-Fuel. High Quality king pellet stove kp130 auger motorPowerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. The vg5790 auger motor Technical Specifications Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise. Wire Length 20 with Male and Female Terminal. CCW1H Auger Motor. High-quality Easy to installThe 1RPM auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The ap5710 auger motor is made of quality stainless steel, durable material that can applied for a long time.

CompatibilityThe auger motor replacement is compatible with all Traeger grill mode EXCEPT PTG and Pit Boss wood pellet grill smokers. Specifications1.6 RPM, 120V 60Hz , 2 Pole. Material Made of Ul 133218awg Pep high-temperature resistance wire and heavy duty plastic construction, the auger motor is built to last. After-Sales Service100 customer satisfaction If you have any questions when you receive the replacement auger motor, please feel to contact us directly We will give you a satisfactory reply within 24 hours. Installation Insturctions from our customer 1 Empty wood pellet bin 2 Unscrew the auger shim holder screw at the bottom of the bin 3 Remove the bottom of the bin cover by unscrewing 4 screws 4 Unplug the motor 5 Unscrew the bolt nut holding the augermotor 6 Plug in the motor 7 Install new motor..

Replacement PU-047040 Auger Feed Motor for Englander 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10 25-PDV, 55-SHP22, 55-TRP22 10-CPM, 49-SHCPM, 49-TRCPM 25-CAB80, 55-SHPCAB80, 55-TRPCAB80 Pellet Stove.. Replacement PU-047040 Auger Feed Motor for Englander 25-PAF, 55-SHP25, 55-TRP25 25-PDVE, 55-SHP22E 25-PDVP, 55-SHP15, 55-TRP15 25-PFS, 25-PFSP 25-PI, 55-SHP20, 55-TRP20 Pellet Stove.. The PU-047040 Auger Motor Technical Specifications --- Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Counter Clockwise. Shaft Diameter 38, Shaft Length 1-18, Wire Length 20 with Male and Female Terminal.. Easy to install The 1RPM Englander 25-PDVC auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration.. Upgrade Quality PU-047040 motor with pure copper motor, it features powerful performance, greater energy efficiency, better conductivity, runs smoothly, longer service life.Auger motor highly suitable for replacing faulty parts or upgrading old ones, with a perfect match and being more cost-effective.

Compatibility Auger Feed Motor Replacement for Whitfield Pellet Stoves Advantage I , II, II-T, II-T Classic, II-T Insert, III , III Insert WP2, Advantage Plus Plus Insert WP7, Optima 2 A02, Optima 3 A03, Profile 20 P9, Profile 30 P10, Cascade WP5, Explorer WF1, Frontiersman WF2. Compatibility Agitator Motor For Whitfield Pellet Stoves T300P, Legend WP1, Prodigy I II WP3, Quest, Quest Plus WP4, Waterford Erin, Renaissance. For Lennox Pellet Stoves PS40 Winslow FS, PI40 Winslow Insert, PS32 Montage, Cascade. Upgrade Quality H5886 motor with pure copper motor, it features powerful performance, greater energy efficiency, better conductivity, runs smoothly, longer service life.Auger motor highly suitable for replacing faulty parts or upgrading old ones, with a perfect match and being more cost-effective. Flexible installation The Agitator auger motor is equipped with a 20-inch wire and provides male and female connectors, which can be removed and replaced according to your stove configuration. Specification Voltage 110 V , Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Clockwise. Replace Part Number H5886, 12026300 12046300.

The Auger Motor Technical Specifications-- Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Clockwise. Wire Length 20 with Male and Female Terminal. CW1H 1 RPM Clockwise Auger Feed Motor with Hole in Shaft, Easy to install.. Compatibility-- Replacement NPAM auger feed motor for Napoleon NPI40, NPI45, NPS40, NPS45, TPS35 Economizer Pellet Stove. Replacement auger feed motor for Timberwolf TPS35, TPI35 Pellet Stove.. Replacement For Part Number--Napoleon part NPAM, Replaces old part numbers W435-0009 and W435-0048.High Quality Auger MotorPowerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. High-quality Easy to install--The 1RPM Napoleon auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration.. High-quality--The CW1H auger motor is made of quality stainless steel, durable material that can be applied for a long time. The Napoleon NPAM auger motor will have your auger system running smoothly while keeping you warm during the cold winter months..

The EF-001 Auger Motor Technical Specifications --- Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Clockwise. Wire Length 20 with Male and Female Terminal.. Compatibility --- Replacement EF-001 Auger Feed Motor For Enviro EF1, EF2, EF3, EF4, EF5, Empress FS, Empress FPI, M55 Agitator Motor, Meridian, Milan, Mini, Solus, Omega, P3, P4, Windsor Pellet Stove. Replacement EF-001 Auger Feed Motor For Vistaflame VF 55 Agitator Motor, VF 100, VF Windsor Pellet Stove.. Compatibility --- Replacement EF-001 Auger Feed Motor For Regency GF40, GF55, GFI55 Pellet Stove. Replacement EF-001 Auger Feed Motor For Hudson River Chatham, Davenport, Kinderhook Pellet Stove.. Replacement For Part Number --- Enviro EF-001, EF4i-001, EF5-116. High Quality Auger Motor Powerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. High-quality Easy to install --- The 1RPM Enviro EF-001 auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CW1 auger motor is made of quality stainless steel, durable material that can be applied for a long time..

Compatibility --- Replacement 80456 Auger Agitator motor for US Stove American Harvest 6033, 6035, 6037, 6039, 6039HF, 6039i, 6039T, 6041, 6041HF, 6041i, 6041TP Pellet Stove. Replacement 80456 Agitator motor for Ashley King APC1406, APCi1406 Pellet Stove.. The 80456 AugerAgitator Motor Technical Specifications --- Volts 120V AC, Amps 0.72 A, Cycles 60 Hz, RPM 4.0, Direction Clockwise. Wire Length 20 with Male and Female Terminal. CW4H AugerAgitator Motor.. Replacement For Part Number USSC 80456. High Quality Auger Motor Powerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. High-quality Easy to install --- The 4RPM auger agitator motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CW4 auger motor is made of quality stainless steel, durable material that can be applied for a long time. Note To best determine compatibility, please double check the spacing on your auger shaft. The auger shaft coils will be spaced 1 apart to indicate set up for 4RPM, whereas 2 spacing indicates set up for 1RPM..

The C-E-017 Auger Motor Technical Specifications --- Volts 120 V, Amps 1.03 A, Cycles 60 Hz, RPM 1.0, Direction Clockwise. Wire Length 20 with Male and Female Terminal. The Breckwell C-E-017 1 RPM Clockwise Auger Feed Motor with Hole in Shaft, Easy to install.. Compatibility --- Replacement C-E-017 auger motor for Breckwell Pellet Stove P1000 Big E, P2000 Tahoe11780 Present, P2000I Tahoe Insert22208 Present, P22 Maverick, P22I Maverick Insert, P23 Sonora7166 to Present, and Units BEFORE 6332, P23I Sonora Insert2243 to Present, and Units BEFORE 1916, P24 Blazer53664 to Present, P24I Blazer Insert53795 to Present, P2700 Mojave8445 Present, P4000 Classic Cast, P7000 Solstic.. Replacement For Part Number Breckwell C-E-017, 20275, 80642. High Quality Auger Motor, Powerful, Quiet, Energy Efficient and Long Lasting. 1 year warranty.. High-quality Easy to install --- The 1RPM Breckwell auger motor is easy to install with 20 inch wire, we provide both male and female spade connectors, depending on your stoves configuration. The CW1H auger motor is made of quality stainless steel, durable material that can be applied for a long time.. To best determine compatibility, please double check the spacing on your auger shaft. The auger shaft coils will be spaced 1 apart to indicate set up for 4RPM, whereas 2 spacing indicates set up for 1RPM..

Replacement PU-4C447 Convection Blower Fan Motor for Englander 10-CDV, 49-SHC22, 49-TRC22 10-CPM, 49-SHCPM, 49-TRCPM 25-CAB80, 55-SHPCAB80, 55-TRPCAB80 25-IP, 55-SHPIP, 55-TRPIP 25-PAH, 55-SHPAH, 55-TRPAH 25-PUF, 55-SHP240, 55-TRP240 25-PUF, 55-SHP240, 55-TRP240 Pellet Stoves.. Replacement PU-4C447 Convection Blower Fan Motor for Englander Models 2002 to Present 25-PDV, 55-SHP22, 55-TRP22 25-PDVE, 55-SHP22E 25-PDVP, 55-SHP15, 55-TRP15 25-PI, 55-SHP20, 55-TRP20 Pellet Stoves. NOTE Please confirm in which year your unit was made in when purchasing. The PU-4C447 Convection Blower Technical Specifications --- Volts 115V, Cycles 60Hz, Amps 1.75A, RPM 1570, CFM 250. 4-516 x 4-78 Flange mounting measuring center to center. Two 13 length wires with 14 male connections. Thermally protected ball bearing design. 3.3 style motor.. This englander pellet stove convection blower fan pu-4c447 is a complete assembly with the housing mounting gasket sold separate. This pu-4c447-amp blower assembly comes with a 1 year manufacturer warranty.. The PU-4C447 Convection Blower is manufactured by FASCO factory. UL Certified, Powerful, Quiet, Energy Efficient and Long Lasting..

Top Quality 2RPM Synchronous Auger Feed Motor for PelPro, Pleasant Hearth and QuadraFire Pellet Wood Stoves.. Fits Models PP130, PP150, PP60, PP70, PPC9,0 TSC90, PH35PS, PH50CABPS, PH50PS, PHC90, Outfitter I, Outfitter II. Durable Design Reliable and efficiently built to withstand continuous operation for dependable performance.. Warranty 1 Year Manufacturer Warranty.

FITMENT The England Stove Works Igniter compatible with Englander Stoves 25-EP, 25-EPI, 25-IP, 25-PAF, 25-PAH, 25-PDV, 25-PDVC, 25-PFS, 25-PI.. REPLACE PART NUMBER PU-CHA, PU-CHA AMP-CIENG. 120V 9.5123 300W Igniter replacement for England Stove Igniter.. SPECIAFICS 38 inch diameter Anti-seize Threading Easy to install and uninstall. 120 Volts 300 Watts Provide continuous sheath temperatures up to 1,200 F. Female Spades Connectors Quick Connect.. PREMIUM QUALITY High Temperature Wire - Fiberglass insulation Fiberglass woven glass strands provides good insulation for use in high temperature process heating applications over stranded Grade A nickel wire. Heat Shrink used on solder joints to prevent breaking.. SERVICE GURANTEE Package include 1Pc x PU-CHA Englander Igniter. If it fails on you stove, feel free to contact us any time..

Replacement Part Number 812-4421, 812-4420, 7000-004, 12-1020, PH-4421. High QualityMade of high quality materials, high reliability and durability, tested many times before leaving the factory, meet or exceed OEM standards.. Specification Includes Motor, Mount Screws Wire Adapter.. Compatible with Models812-4421 Auger Feed Motor Compatible with Quadra-Fire Models CAB50-C, Castile FS, Castile FS MBK, Classic Bay 1200, Classic Bay 1200i, Contour, Mt Vernon E2 FS, Mt Vernon E2i, Santa Fe B, Santa Fe MBK, Santa Fe-C INS, Trekker Insert, PS35, PS50 etc.. Service We always provide cost-effective products that consistently meet our customers' needs. If you have any question about this Auger Feed Motor, please contact us at any time.

Pellet Grill Auger Motor Shaft Nut Bolt, Just replace the old Auger Motor Shafts Nut Bolts, Replacing the new Shaft Nut Bolt set reactivates the motor and rotating screw for work and feeding. Fits for Traeger Z Grills Embers Grills Grilla Grills Rec Tec Englander pellet stoves and grills. Used to secure the auger shaft to the auger motor, Ideal for use on most pellet grills. The package includes 3 pcs Auger Motor Shaft Nuts Bolts. Check the size before purchase, and avoid buying the wrong motor nuts and bolts, Easy to install, can be directly replaced and fixed. Please make sure it is compatible with your grillsmokers. Many auger motor shaft nuts look similar but are completely different models. Don't buy the wrong one.

UsageThe auger motor shaft nut bolt kit is ideal for use on most AC pellet grills to fasten the auger shaft to the auger motor.. Fit forAuger motor pins are specific to AC pellet grill, compatible with brands Traeger, Pit Boss, Rec Tec, Z Grills, Camp Chef, Grilla Grills, Embers, Cabelas, Englander, etc. Replacement Part NumbersFor Pit Boss auger motor shaft nut bolt, 74072, 74073 For Camp Chef pellet grill auger motor shaft bolt, pg24-25 For Traeger wood pellet grill auger motor shear pin SUB186, KIT0783. Easy To InstallThe installation is really easy, plug and play. The auger motor pin is situated between the auger motor and the auger bushing, the shear pin secures the auger in place inside the auger shaft. Get your pellet grill fired up again with this replacement auger motor shear pin. Package Includes2 Sets auger motor shaft nut bolts. Check the size before you buy to prevent getting the wrong motor nuts and bolts..

CompatibilitySRV7000-670 auger feed motor for Pelpro PP130, PP60, PP70, PP130-B, PP130B, PPC90, TSC90, PP60-B, PP60B, PP150, PPC90 pellet stoves. Auger motor for Pleasant Hearth PH50CABPS, PH35PS, PH50PS, PHC90 pellet stoves.. Quiet OperationThis auger feed motor replacement is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel. Safe and reliable to use.. High QualityThe PelPro Pleasant Hearth auger feed motor is made of high-quality materials, it features powerful performance, greater energy efficiency, runs smoothly, energy saving and long lasting.. Technical Specifications Volts AC 120V, Cycles 60Hz, 2 RPM, Direction CW or CCW, Connector 3 Pin Molex.. Powerful Functionality2 RPM auger motor is easy to install, and replacement improves pellet utilization for better pellet stove operation. Keeping you warm during the cold winter months..

Replacement Part Number 812-4421, 812-4420, 7000-004, 12-1020, PH-4421. Fits Models Compatible with Quadra-Fire Pellet Stove Models --Classic Bay 1200 Insert CB1200i Contour Castile Insert Classic Bay 1200 Freestanding CB1200FS Castile Freestanding Mt Vernon Original 4 Spd Model. Mt Vernon E2 InsertMt Vernon E2 Santa Fe B Santa Fe Freestanding Trekker InsertSanta Fe Insert Trekker 200 FS, 1200i, Castile FSMt Vernon OE Compatible with Heatilator Eco-Choice Models-- PS50CAB50 PS35 7000-500 PH. Product Specs 2.4 RPM Clockwise Rotation, 120 Volts, 14-inch Shaft, 3 Pin Connector. Includes Motor, Mount Screws Capacitor Bypass Wire Adaptor. Feature Made of premium material, it has the advantages of long service life, low noise, high vibration frequency, sufficient power, easy installation and so on. Service We always provide cost-effective products that consistently meet our customers' needs. If you have any question about this Auger Feed Motor, please contact us at any time.

Compatible Smoker Grills- The upgraded auger motor replacement for all Traeger, Pit BossEXCEPT PTG and Camp Chef, Oklahoma Joe, Cuisinart WoodCreek and Cabelas Pellet Grills. Such as Traeger 070, 075, Texas Elite Series, Pro 22, Pro 34, Lil Tex Elite Series, pit boss pro series 850, 820, pit boss austin xl, oklahoma joe rider dlx smokers, etc. Powerful 2.0RPM Auger MotorOffers 25 more power compared to 1.6RPM motors. Results in smoother grill operation, minimizes large temperature fluctuations, and reduces auger clogging. Universal grill auger motor kit with parameters 2.0 RPM, 120V 60Hz 2 Pole. Heavy duty replacement helps power the auger to move pellets from the hopper to the firepot during cooking. High - Quality ConstructionTraeger auger motor replacement wire is made of UL133218AWG Pep special high - voltage and high - temperature - resistant wire. Every Auger Motor is run checked and tested at the factory to make sure that they meet quality control standards, ensuring durability and long - lasting performance. Simple InstallationThe Pit Boss Auger Motor Replacement features a plug - and - play design. Enables grill restoration in just a few minutes, saving both time and money. Please make sure you are purchasing from QuliMetal with brand - name package. PackagePackage includes 1 Pit Boss auger motor 2.0 RPM, 120V 60Hz 2 Pole check your grill model before ordering to ensure compatibility. We have professional engineer team online 24 hours a day to solve any problems for you.

Wide Compatibility The universal auger drive motor replacement is suitable for all Traeger, Pit Boss except PTG and Camp Chef, Oklahoma Joe, Cuisinart WoodCreek and Cabelas pellet grills. Suitable for Camp Chef smoker grills. Including but not limited to Traeger 070, 075, Texas Elite Series, Pro 22, Pro 34, Lil Tex Elite Series.. Excellent Durability This replacement auger motor for pit boss grill is made of high temperature resistant UL 133218AWG PTFE wire, equipped with sturdy plastic gears, running smoothly and without noise, the motor housing is plastic, not easy to strip, it can provide long-term service.. Prevent Auger Clogging 2 rpm replacement barbecue auger motor can power your auger, help reduce temperature fluctuations when using the auger and reduce clogging. 2-pole design, high efficiency and reliability, ensure stability even during high-load operation.. Easy Installation Plug and Play, simple and convenient, allowing you to easily replace a burned out or neglected motor without professional skills. Simply remove the auger motor assembly and feeder gear motor, and replace with a new auger motor replacement parts kit.. After-Sales When your pellets fail to feed into the fire, it may be time to replace the auger motor. Please check your grill model when purchasing. If you have any questions after receiving the auger drive motor replacement parts, please feel free to contact us directly.. Please note Oversized or damp pellet fuel can cause blockages and motor overload, potentially damaging the motor. Please use standard 6mm pellet fuel and remove all remaining fuel after use. Damage or deformation of other components in the fuel hopper will also affect motor operation. Therefore, before replacing the motor, please check the fuel hopper for damage and blockages, and use standard 6mm pellet fuel to avoid motor overload..

PLUG AND PLAY - Replace drive motor kit, Compatible with most Traeger, Traeger 070, 075, Texas Elite Series, Pro 22, Pro 34, Lil Tex Elite Series and Pit Boss Wood Pellet Grills TIP EXCEPT PTG, and fit for Camp Chef smoked grill.. 1.6 RPM AUGER MOTOR - 110V 60Hz 2 Pole, heavy duty replacement auger drive motor.. KEEP THE FIRE FED - The auger drive motor and the screw push rods are used together to keep the fire source.. EASY TO INSTALL - Replace burned or neglected grill auger motor, must have when grilling.. FRIENDLY SERVICE - If you have any questions, please contact us through Amazon Messenger..

PU-047040 Auger Motor Specifications 120V, 1.03A, 60 Hz, 1RPM, Counter Clockwise, Wire Length 20 with 14 Male and Female Terminal, 38 Diameter x 1 18 Length Shaft, Replacement Part Numbers PU-047040. Widely Compatible PU-047040 Auger Feed Motor and PU-UCF204-12 Auger Bearing Replacement for Englander Pellet Stove Models 25-PDV, 55-SHP22, 55-TRP22, 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10, 25-PDVE, 55-SHP22E, 25-PDVP, 55-SHP15, 55-TRP15, 25-CAB80, 55-SHPCAB80, 55-TRPCAB80, 25-PAF, 55-SHP25, 55-TRP25, 25-PFS, 25-PFSP, 25-PI, 55-SHP20, 55-TRP20. Easy to Install Auger Motor PU-047040 comes fully assembled, easy to install, Auger motor is made of stainless steel, durable material that can be applied for a long time, PU-UCF204-12 Auger Bearing has abrasion resistance, meaning it will not deteriorate under strong pressure. Powerful Functionality The auger motor's function is to manage the rate at which the pellets go through into the combustion compartment, which aids in maintaining the desired level of heat output and regulating temperature PU-047040 Auger Motor is designed to provide reliable, efficient performance to ensure your heating system runs smoothly and effectively. Quiet Operation PU-047040 Auger Motor is a durable sealed ball bearing motor, safe and reliable to use, This upgraded motor has enough oil between the internal gears, so the gears rotate without making loud noise and rotate stably, The PU-UCF204-12 Auger Bearing has a solid cast iron housing that provides a sturdy base for the bearing to keep it in place.

Compatible WithSRV7000-670 Auger Feed Motor Replacement for Pelpro PP130, PP130-B, PP130-RF, PP60, PP60-RF, PP70, PP150,PPC90, TSC90 Pellet Stove.. Fits ModelsSRV7000-670 auger feed motor Replacement for Pleasant Hearth PH35PS, PH50CABPS, PH50PS, PHC90 pellet stove.. Outstanding SpecificationsThe PelPro PP130 Auger Motor parameter 2RPM 120V, Cycles 60 Hz, DirectionCW or CCW. package Includes pelpro pp130 auger motor 3 Pin Molex Connector.can meet your installation needs, avoid the time to buy spare parts, and save your time and energy.. High QualityThe PelPro Pleasant Hearth Auger Feed Motor is made of high-quality raw materials, and the products are produced in strict accordance with OEM standards. They have undergone multiple inspections before leaving the factory to ensure the quality of the products.. Professional after-sales serviceWe have a professional after-sales team. For whatever reason, we will reply to you within 24 hours, giving you a sincere attitude and a satisfactory solution. We pride ourselves on understanding consumers' needs and how to meet them..

Available for Pelpro brand PP130, PP130-B, PP60, PP60-B, PP150, PPC90, TSC90 pellet stoves.. Available for Quadre-Fire brand MT Vernon E2, MT Vernon E2 Insert, Trekker, Trekker Insert, Outfitter-I, Outfitter-II pellet stoves.. Available for Pleasant Hearth PH35PS, PH35PS-B, PH50PS, PH50PS-B, PH50CABPS, PH50CABPS-B, PHC90 pellet stoves. Precision manufacturing technology and high quality workmanship ensures that our feed motor is quieter and more durable.. Made of high-quality materials, rigorous factory testing ensures superior quality and performance, we also provide good customer service and 1-year warranty, so you can have peace of mind during use..

IDEAL AUGER MOTOR REPLACEMENT PARTS 2.0 RPM, 120V 60Hz 2 Pole Heavy Duty Auger Motor Compatible with TraegerEXCEPT PTG, Pit Boss, Camp Chef wood pellet grill smokers.. UPGRADED 2.0RPM AUGER MOTOR WITH MORE POWER Compaired with the 1.6RPM auger motors, Our 2.0RPM auger motor provide stronger power make the grill run smoother, which help reduce large temperature fluctuations and reduce clogging when using augers.. HIGH QUALITY Upgraded Auger Motor wire, Made of UL133218AWG Pep Special High Voltage and High-Temperature Resistance Wire, strict factory inspection make it durable and long last.. EASY TO INSTALL Plug and Play. Just a few minutes, your grill will work again, save your time and money.. AFTER-SALES SERVICE If you have any questions about our Auger Motor, Please feel free to contact us, we will provide you with a satisfactory solution within 12 hours..

PERFECT COMPATIBLE WITH ENGLANDER MODELS - 25-CAB80, 55-SHPCAB80, 55-TRPCAB80,25-CBEP, 55-SHPCBEP, 55-TRPCBEP,25-EP, 55-SHPEP, 55-TRPEP, 25-EPI, 55-SHPEPI, 55-TRPEPI,25-IP, 55-SHPIP, 55-TRPIP,25-PAF, 25-PDV, 55-SHP22, 55-TRP22,25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP20,25-PUF, 55-SHP240, 55-TRP240,25-PUF, 55-SHP240, 55-TRP240 Auto-Start units that have a manufacture date of 2004 or later.. SPECIAFICS 38 inch diameter Anti-seize Threading Easy to install and uninstall. 120 Volts 300 Watts Provide continuous sheath temperatures up to 1,200 F.. REPLACE PART NUMBER PU-CHA, PU-CHA AMP-CIENG. 120V 9.5123 300W Igniter replacement for England Stove Igniter.. PREMIUM QUALITY High Temperature Wire - Fiberglass insulation Fiberglass woven glass strands provides good insulation for use in high temperature process heating applications over stranded Grade A nickel wire. Heat Shrink used on solder joints to prevent breaking.. PackagePackage included igniter 1. The metal part of the ignition rod is 4.8 and the wire lead is 15.8, Female spades connectors are easy to install, can quickly Ignite your stove and send the warmth through all rooms in your home..

1 RPM, COUNTER CLOCKWISE Rotation When Facing Shaft 120 V, 60 HZ, 1.03 Amps 38 Diameter x 1 Length Shaft Flat Edge of Shaft for Securing with Set Collar. Wire leads measure 20 in length. We include both male and female spade connectors depending on your stoves configuration.. Gearbox Measures 2 Wide x 4 58 High x 1 Width Width to screw mount hole 1 516 Total width including magnet, armature and gearbox measures 2 18.. Highest Durability and Lowest Operating Decibels Exceeds all OEM aftermarket motor standards. Exclusive 1 Year warranty with our no hassle replacement guarantee.

FREE Tech Support. Use amazon messager to contact Seller.. RPM 1, Voltage 115 VAC 60 Hz. Motor Protection Thermally Protected Bearings Oilless. Termination 2 wire with AMP terminal. Warranty 1 Year.

Replaces PU-047040, 1 RPM - 120V AC. Full 1 Year Warranty. Sealed Ball Bearing - Best on the Market. Free Shipping - Guaranteed Best Price. Our Premium Motor - Made in the USA.

Highest Quality Englander Auger Feed Motor Replacement. Needle Point Ball Bearing, USA Made, 1 Year Warranty.. Fits Models 25-PDV 25-PDVC 25-PI 25-PAF 25-PDVP 55-SHP10 55-SHP10L 55-SHP20 55-TRP10 55-SHP22 55-SHP22L 55-TRP15 55-TRP22 SHP25 55-TRP25 American Heritage American Standard US 25-5670. Replaces Part PU-047040 B4415UI. 38 Diameter x 1 18 Length Shaft 120V AC, 60Hz. Genuine Gleason Avery Brand Top Tier Motor.

FEEDAUGER MOTOR FOR 10-CPM 49-SHCPM 49-SHCPML 49-TRCPM Pellet Utility Furnace Models with PUF in the model number Pellet Auxiliary Heater Models with PAH in the model number Evolution Pellet Models with EP in the model number Imperial Pellet Models with IP in model number. STIRRERAGITATOR MOTOR FOR Turns the agitator bar in the fire pot CORN stove models 10-CDV 49-SHC22 49-TRC22. Replaces Part PU-047042 - Exceeds all OEM aftermarket motor standards. Highest Durability and Lowest Operating Decibels. Exclusive 1 Year warranty with our no hassle replacement guarantee.

Correct replacement for both the top and bottom auger motors in England Stove Works pellet stoves.. Highest Quaility Auger Motor - PU-047040, Auger Bearing Replacement for PU-UCF204-12. Auger Bearing Gasket Included - PU-ABG. One Year Warranty. Free Lifetime Tech Support from ESESStoves.

Bottom Auger Feed Kit For Englander Pellet Stoves Made 1992 And Later 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10, 25-PAF, 25-PI. Includes 1 RPM Counter Clockwise Auger Motor, PU-047040. Also Includes Auger Bearing Block Bearing, Locking Collar, Bottom Auger Shaft Part PU-AF11B, Two Styles Of Bearing Gaskets. Stoves Made Before 2001 Use The Soft Fiberglass Bearing Gasket and Newer Stoves Use The Nylon Bearing Gasket. Extremely Durable, Easy Installation.

Fits Models 25-PDV 25-PDVC 25-PI 25-PAF 25-PDVP. 25-PDVT 55-SHP10 55-SHP10L 55-SHP20 55-TRP10 55-SHP22 55-SHP22L. 55-TRP15 55-TRP22 SHP25 55-TRP25 American Heritage American Standard US 25-5670. Part NumbersPU-047040 B4415UI PH-CCW1. Contact with us If you have questions about part number model ..

2PACK - England Stove Works Auger Motor. 1RPM, 120V ACEngland Stove Works Auger Motor. Improved Easy Install with 12 Wire Leads. Full 1 Year Warranty. Free Shipping - Guaranteed Best Price.