Yuesstloo engine camshaft alignment timing tool kit is used to lock and align the camshaft, crankshaft, and time belt tensioner at the correct timing position, and also adjust the VTC device.. Compatible with the following engines ompatible with FORD Duratec petrol engine 1.25L, 1.4L, 1.5, 1.6L, 1.7L, 1.8L, and 2.0L twin cam 16V, 2.3L, 2.5L engine, Compatible with FORD Duratorg diesel engine 1.4L, 1.6L, 1.8L, 2.0L TDCI, Compatible with FORD ECOBOOST 1.6L Ti-VCT, 1.51.6 VVT, Compatible with MAZDA PSA 1.4L, 1.6HDI, 1.8L, 2.0L, 2.3L. Volvo 1.6T. Replace OEM Equivalent Part Number 303-1097 303-748 303-1550 303-1552 303-1054 303-1059 303-735 303-1552 303-393A 303-393-01 303-393-02 303-376B 303-651 303-193 303-507 303-734 303-732 303-xtra 303-574. Compatible with the following FORD Focus 1998-2008, Focus C-Max 2003-2008, Mondeo 2007-2008 1.6 Ti-VCT 16V Diesel, Duratorq Fiesta Courier 2000-2006, Tourneo Connect 2002-2008, Transit Connect 2002-2008, Fusion 2002-2008, S-Max 2006-2008, Galaxy 2006-2008, Escape, 2012 Ford B-Max 1.4L Duratec-16V, and 2015 Ford C-Max 1.5L EcoBoost.. Fitment Vehicle compatible with the following vehicles 2011 Ford C-Max 1.6L EcoBoost, 1.6L Duratec-16V Ti-VCT, 2013-2014 Ford Fusion 1.6L EcoBoost, 2013-2018 Ford Fusion 1.5L EcoBoost, 2014-2016 Ford Transit 1.6L EcoBoost, 2003-2005 Mazda MP 3.0L, 2004-2006 Mazda Tribute 2.0L, 2.3L, 3.0L, and 2004-2009 Mazda 3 2.0L, 2.3L, excluding 2.3T.. Engine Code 1.6 16V FYDAC, FYDBD, FYJA, FYJB, L1F, L1J, L1L, L1N, L1O, L1T, L1V, L1W, HWDA, HWDB 1.7 16V MHA, MHB 1.8 16V EYDB, EYDC, EYDD, EYDE, EYDJ, EYDG, EYDI, EYDJ, EYPA, EYPC, RKA, RKB, RKF, RKH, RKJ, RKK 1.8 16V with control chain CDBB, CGBAB, CHBAB, CSDA, CSDB, QQDA, QQDB, QQDC 2.0 16V EDBAC, EDBB, EDBD, EDDB, EDDC, EDDD, EDDF, NGA, NGB, NGC, NGD 2.0 RS ST170 ALDA, HMDA 2.0 16V with control chain AODA, AODB, AOWA, CJBAB.

Universal Fit This LS flywheel locking tool is compatible with ChevyGM, LS1, LS2, LS3, LS6,clears all rear-wheel drive bellhousings-manual and automatic Do not work for Front-wheel drive engines compatible with GM 97 -2019 rear-wheel drive V8 LS and LT baised engines,cars and trucks 4.8, 5.3, 5.7, 6.0, 6.2, 7.0 liter Will not fit Gen 3 coyote 18 and up engines. Easy Installation This flywheel holding tool just need to be bolted in place of your stater and and tighten them. Essential Tool This flywheel holder tool locks the flywheel to the engine, prevents the flywheel from moving an essential tool for removing and installing Chevrolet engine harmonic balancer. Kit Includes This flywheel holding locking tool comes with 1 x Engine Flywheel Locking Tool 2 x proper bolts FD 8.8 1 x pair of gloves.

Wide Applications Specifically designed for use with Caterpillar CAT engine series including 3176, 3196, 3200, 3208, 3300, 3400, 3406, 3500, 3508, 3512, C9, C10, C12, C13, C15, and C16. Also compatible with Mack E-7, E-7 ETEC engines. Perfect for both EUI and MUI systems.. Efficient Engine Rotation The barring socket is expertly designed to mesh seamlessly with every flywheel tooth, making engine rotation effortless and saving you time and energy during repairs or maintenance.. Premium-Grade Material Crafted from high-quality 42CrMo steel, ensuring superior durability, excellent tolerance, and resistance to corrosion and rust, making it a reliable tool for long-term use.. Precise Dimensions Features 8 splines with a 1.725 43.815mm diameter and a 12 square drive, providing a precise fit for optimal performance during engine servicing.. Direct Replacement Replaces OEM part numbers J-38587-A, Caterpillar 9S9082, 0508477, and OTC6749, offering a cost-effective alternative with the same quality and reliability as the original tool..

SIMPLE REMOVAL TOOL Our flywheel locking tool grabs the teeth of your flywheel or flexplate providing torque to quickly remove or install the car flywheel or flexplate Our turner helps you apply proper torque to nuts during flywheel installation. COMPLETE ENGINE ACCESS Sometimes it takes a specialty tool to get all of your engine work done efficiently This flywheel removal tool will remove flexplates and flywheels so that you can service clutches, transmission, and rotate the crackshaft. FLYWHEEL HOLDER Removing your flywheel bolt or torquing the harmonic balancer bolts can be a nightmare without a flywheel key Lock your cars flywheel sprocket or flexplate in position to get adequate nut torque for removal and installation jobs. COMFORTABLE FLYWHEEL PULLER Working beneath your vehicle is uncomfortable Let this flywheel turning wrenchs sure grip handle keep you locked on the flywheel teeth without hand slippage during torquing This flywheel tool folds for easy storage. SPECIALTY WORKING TOOL Other tools cant handle the pressure of removing your flywheel Our spring tensioned flywheel remover keeps your flywheel turning wrench securely engaged while torquing the harmonic and car flywheel bolts.

1.5 Timing Tool KitThe Engine Camshaft Alignment Timing Tool Kit contains all the necessary tools and accessories to enable you to accurately perform engine timing system adjustments and maintenance, ensuring engine efficiency and reliability. The 1.5 1.6 Engine Timing Tool Kit can lock and align the camshaft, crankshaft, timing belt tensioner in the correct timing position, and can also adjust the VTC device.. Suitable Engine1.5 1.6 Timing Tool Kit is compatible with Ford Duratec petrol engine 1.25, 1.4, 1.6, 1.7, 1.8, and 2.0 twin cam 16V, 2.3L, 2.5L engine compatible with Ford Duratorg diesel engine 1.4, 1.6, 1.8, 2.0 TDCI compatible with Ford Ecoboost 1.6 Ti-VCT, 1.51.6 VVT compatible with Mazda Psa 1.4, 1.6HDI,1.8L, 2.0L, 2.3L. Engine Code-11.25 16V DHA, DHB, DHC, DHD, DHG, DHH, M7JA, M7JB, F8JA, F8JB, FUJA, FUJB 1.4 16V ASDA, ASDB, FXDA C, FXDB D, FHA, FHD, FHE, FHF, FXJA, FXJB. Engine Code-2Engine Timing Tool Kit for 1.6 16V FYJA, FYJB, FYDAC, FYDBD, L1F, L1J, L1L, L1N, L1O, L1T, L1V, L1W, HWDA, HWDB 1.7 16V MHA, MHB 1.8 16V with control chain CDBB, CGBAB, CHBAB, CSDA, CSDB, QQDC, QQDB, QQDA 1.8 16V EYDB, EYDC, EYDD, EYDE, EYDG, EYDI, EYDJ, EYPA, EYPC, RKA, RKB, RKF, RKH, RKJ, RKK 2.0 16V EDBAC, EDBB, EDBD, EDDB, EDDC, EDDD, EDDF, NGA, NGB, NGC, NGD 2.0 16V with control chain AODA, AODB, AOWA, CJBAB 2.0 RS ST170 ALDA, HMDA.. OE Equivalent Part Number ReplacementEngine Camshaft Timing Tool Kit replaces OE 303-1097 303-1552 303-376B 303-651 303-393A 303-393-01 303-393-02 303-1270 303-1550 303-1054 303-193 303-732 303-735 303-620 303-1059 303-507 303-748 303-574. Fitment Vehicle1.5 1.6 Timing Tool compatible with 2011 Ford C-Max 1.6L EcoBoost, 1.6L Duratec-16V Ti-VCT13 - 14 Ford Fusion 1.6L EcoBoost 13 - 18 Ford Fusion 1.5L EcoBoost 14 - 16 Ford Transit 1.6L EcoBoost 04 - 06 Mazda Tribute 2.0L, 2.3L, 3.0L 04- 09 Mazda 3, 2.0L 2.3Lnot fit 2.3T 03 - 05 Mazda MP 3.0L Duratec petrol engine 1.25, 1.4, 1.6, 1.7, 1.8, 2.0 Twin Cam 16V Duratorg diesel engine 1.4, 1.6, 1.8, 2.0 TDCI Escoboost 1.6 Ti-VCT 1.51.6 VVT etc...

APPLICATIONPACCAR MX, PACCAR MX PMCI-2, PACCAR MX-13 PCI, MX-11 and PACCAR MX-13 Engines Commonly Used on Peterbilt and Kenworth T880 Trucks. DAF 35-42 TONS EURO 4 Truck, 12 Drive. BEST DESIGN Works Perfectly for Barring Over the Engine to Make Clutch Adjustments. HIGH QUALITY Well-Designed, Excellent Processing. Constructed of Heavy Duty,Carbon Steel and Heat Treated for Superior Strength. REPLACEMENTHeavy Duty Replacement for OEM Part 1453158PE 1453158. PACKAGE INCLUDED 1 Engine Barring Tool.

8809 Flywheel Locking Tool is used to lock the flywheel while the transmission is removed for service.. Applications Compatible with BMW N20 M47TU M54 M57T2 M57TU N40 N42 N43 N45T N46 N46T N51 N52 N53 N54 N62 N73 S85 W17 engines.. Comparable to BMW factory tool 119260.. Ultra-precise design, made of high quality material, with high hardness, durability and anti-corrosion.. If you have any questions with the Flywheel Locking Tool, please feel free to contact us..

APPLICATION - This flywheel puller tool designed for Polaris RZR 1000 900 570 2011- UPRanger 900 2011- UP Ranger 1000 2017- UP General 1000 2016- UP Ranger 570 2014- UP Sportsman 850 2009- UP Sportsman 570 2014- UP ACE 570 2016- UP.. SIZE - Flywheel puller is 50mm diameter x 1.5 left-hand thread pitch-female. Reverse Thread Design.. EASY TO USE - Used for removal of Polaris RotorFlywheel Part Numbers 4013225 4014404 4013969 and others. We suggest applying lubricating oil on the tools before use.. MATERIAL - Made of high quality steel. Strong and Durable. Central thread design can fix itself firmly and will not loosen while using.. NOTE - Please check the model carefully before purchasing to ensure that the product is the same as your desired model..

Compatible with Chevy LS 1 2 3 LSX, clears all RWD bellhousings-Manual and Automatic do not work on FWD engines. TIG welded using 14 cold rolled USA Steel, proven design for strength and reliability. Easy to install - just bolts in place of your starter and locks securely into the flywheel teeth. These tools are designed to work on engines mounted to an engine stand or an engine already installed in the vehicle. Packing 1PCS Engine Flywheel Locking Tool Comes with two proper length grade 8.8 bolts.

APPLICATION--- Fit for DD13 DD15 DD16 MBE 4000 MBE 900 Detroit Diesel, Mercedes Benz Actros, Atego, Man 5, 6, 8-cylinder engines - D2528.. REPLACEMENT--- This tool is comparable to the J-46392, and the W904589046300.. FUNCTION---Designed to adjust the engine for correct position. Used with 12 drive wrench. This tool is used to bar the engine over for service procedures, installs to engage the flywheel teeth and rotate the engine using standard square drive hand tools.. HIGH QUALITY MATERIAL---Constructed with high quality carbon steel, which is the best quality of those markets in sale, with great strength and durability for years of trouble-free use.. 100 Satisfaction Guarantee If you're not 100 satisfied with our items, simply return it for refund within 30 days. Support 12-month Warranty. Professional Sincere Service allows you to take no risks to purchase in E-cowlboy.

Applicable Engine Compatible with BMW M47T2, M47TU, M57T2, M57TU, M67, N45, N45T, N46, N46T, N51, N52, N53, N54 and W17 engine. Note Some models from certain years are not applicable, please check your vehicle model carefully. Function Designed for locking flywheels and crankshafts and is required when loosening the flywheel, crankshaft pulley or other work where locking crankshaft is required. OEM Equivalent Part Number 118180, 118181, 118182, 118183 and 118185, 83300493587, 83-30-0-493-587, 83 30 0 493 587, 83.30.0.493.587. Tips for Use When installing the tools, make sure that the claw of the locking lever are engages with the starter gear ring, for locking the flywheel and therefore the crankshaft. A Complete Set This flywheel holding tool kit includes flywheelcrankshaft alignment pin, locking pieces, basic body, adapter E65M67, adapter with setting sleeves E46 m47TU, a portable case and instruction manual.

Compatible with Cummins B C Series Engines Designed for use on 3.9L, 5.9L, 6.7L, and 8.3L turbo diesel engines found in Dodge pickups, including Cummins B C series engines.. Effortless Engine Rotation This tool allows you to manually rotate the engine with ease, providing a smooth and efficient method for engine maintenance.. Friction-Free Operation The load-bearing collar ensures friction-free movement while rotating the tool in the housing, making the task easier and more efficient.. Simple to Use Simply insert the tool into the flywheel housing to engage the ring gear, then attach a 12-inch square drive ratchet or breaker bar to rotate the engine.. OE Replacement Parts Replaces Cummins part numbers 3824591A, 5299073, and OTC-7471A, providing a reliable solution for your engine rotation needs..

Application 4024, 4039, 4045, 4239, 4276, 6359, 6076, 6081, 6090, 6105, 6125, 6619, 6059, 6068 and 6135 engines.. Replaces Models JDE81-1 JDE81-4 JDG820. High Quality Engine Turning Tool and Timing Set is crafted from premium metal, capable of withstanding immense torsional stress from the engine. It ensures no deformation or wear during repeated use, delivering reliable operational rigidity and extended service life.. Function The Engine Turning Tool and Timing Set features an all-metal JDE81-4 locking pin, significantly stronger than standard materials. It precisely inserts into the timing hole and locks securely, keeping the engine stable at TDC during inspection. The complete set of JDE81-1 turning tool and JDE81-4 metal locking pin works in perfect synergy, enabling one-stop flywheel turning and TDC locking to ensure continuity and accuracy throughout the timing inspection process.. Easy Installation The Engine Turning Tool and Timing Set strictly corresponds to genuine tool part numbers JDE81-1, JDE81-4, and other genuine tool part numbers. Specifically engineered for over ten major Deere engine models, it guarantees perfect alignment with flywheels and timing holes for precise positioning. Designed to exact OEM specifications, both the turning tool's teeth and the locking pin's diameter perfectly match the engine's original design, ensuring seamless integration and damage-free installation..

CompatibilityGY6 50 125 150cc Kawasaki Yamaha Suzuki Honda KTM Scooter ATV Dirt Bike, Small Engines and so on. more fitment information, please read the description below.. Fitment24mm0.94in side thread use for-most GY6 50 4 Stroke Scooter Moped ATV. 27mm1.06in side thread use for-most GY6 125 150cc Scooter and other 125cc Motorcycles.. MaterialMaterial is magnetic steel, surface phosphating antirust proc, sturdy and durable.The specially designed reverse thread and magnetic steel structure ensure a secure grip, making one tool suitable for all efficiencies.. Key tipDon't forget that the flywheel turning tool has reverse threads, which require counterclockwise rotation to tighten.. PackageFlywheel Puller Kit x 1 M24x1 RH M27x1 LH.

Compatible withApplication to rotate flywheel on engines with 142 tooth flywheel ring gear and a 26.5 mm 1.04 in. ID flywheel housing guide bore diameter. Application 3179, 4239, 6359, 4276, 6414, 3029, 4039, 4045, 6059, 6068, and 6619 Engines.Alternative to JDE83 JDE81-4TIMING LOCK PIN. Simple InstallationThis Engine Turning Tool Is Designed To Rotate The Engine Flywheel To The TDC Top Dead Center Position, Locking The Engine In Place For Accurate Timing Checks Of The High-pressure Fuel Pump. Direct replacement, NOT require any modification. High-QualityMade from high-quality materials for ultimate durability Manufactured to meet or exceed strict quality requirements. Note Please confirm that the parts are the correct ones you need before purchasing. If you are not sure, please contact us for verification.

It is necessary to hold the flywheel in a secure position while servicing the balancer retaining bolt.. The EN-46547 provides for damage free securing of the flywheel utilizing the access hole in the bell housing and reducing the likelihood of case damage. Mechanical Engine Flywheel Holding Tool. Type Flywheel Holding Tool. Application IN-LINE 4 5 ENGINE. OEM no. ref. EN-46547. The EN-46547 provides for damage free securing of the flywheel utilizing the access hole in the bellhousing and reducing the likelihood of case damage.

COMPATIBILITY LS flywheel locking tool replacement for LS1, LS2, LS3, LS6, LSX engine, for GM V8 LS and LT baised engines, for car and truck 4.8, 5.3, 5.7, 6.0, 6.2, 7.0 L Not fit Gen 3 coyote 18 and up engines. MANUFACTURING PROCESS Automotive flywheel locking tool is made of 14'' cold rolled steel TIG welded for high strength and quality to withstand high torque. It is very sturdy and well made to work as intended. ESSENTIAL TOOL Flexplate locking holder tool is a must have tool for removing and installing the harmonic balancer on your engine. It locks the flywheel on the engine, prevents the flywheel from moving, and allows you to easily and efficiently torque the flywheel bolts to the starter position. EASY INSTALLATION You can install the flywheel locking tool directly in the designated position, the teeth on the tool engage with the teeth on the flywheel exactly, which can easily fix the flywheel and improve your working efficiency. PAVKAGE 1PCS Engine Flywheel Locking Tool 2 PCS Grade 8.8 Bolts. If you have any questions about the product, please feel free to consult with us, we will provide you with better service.

Great Compatibility Fit for all 2008-2020 Volvo D11, D13, D16 and Mack MP7, MP8, MP10.. Upgrade Design Used to turn the Crankshaft flywheel in order to position it during timing procedures. Remove flywheel cover plugs and place the rotation tool, to rotate the flywheel with ease. The Crank Flywheel Tool will rotate freely while barring the engine over.. Must Have Tool If youre planning on performing an overhead adjustment or are replacing your injectors on your D13, this tool is a must-have in your toolbox. Special designed to rotate the flywheel of crankshaft for correcting the timing position.. Special Features Directly replaces OEM Part Number 88800014 88840317 and work in a easier way to save your time and money.. 100 Satisfaction Guarantee If you're not 100 satisfied with our items, simply return it for refund within 30 days. Support 12-month Warranty. Professional Sincere Service allows you to take no risks to purchase in E-cowlboy.

Fitment - Used for holding the flywheel on fit for Ford 1.5L 1.6L engines. Apply to Escape, Fiesta, Fusion Transit Connect. Compare to Factory Tool 303-393A, 303-393-01 303-393-02. Feature - This flywheel locking tool is now available with 2 extra adaptors allowing use on a larger model group in the range in both petrol and diesel engines.. Package Includes - 1Pcs Flywheel Locking tool 21-168303-393, 1Pcs Flywheel Locking tool adaptor 01 303-393-01, 1Pcs Flywheel Locking tool adaptor 02 303-393-02. Service - You will receive 90 days shelf life on flywheel locking tool kit, hassle-free return and money back policy, buy with confidence If you have any questions about flywheel locking tool, please contact us by email, we will reply you within 12 hours.

Making Work Effectively - Are you always in trouble with the flywheel stator replacement Trying Valchoose Flywheel Stator Magneto Puller, work like a charm, quick tip, use your impact wrench to break loose, very Easy and Effective. Fitment Items - GY6 50 125 150cc Kawasaki Yamaha Suzuki Honda KTM Scooter ATV Dirt Bike, Small Engines and so on. more fitment information, please read the description below. 24mm27mm Double Head Size - 24mm0.94in side thread use for---most GY6 50 4 Stroke Scooter Moped ATV. 27mm1.06in side thread use for---most GY6 125 150cc Scooter and other 125cc Motorcycles. Material is magnetic steel, surface phosphating antirust proc, sturdy and durable. Tips - Need the repair tool for removing flywheel to replace the stator. Do not forget the puller are Reverse threaded Please carefully check whether your model is applicable to our products before buying. Kindly Reminder - Please check the model number carefully to make sure you don't order the wrong item, if you are not sure fitting or not, feel free to contact us to confirmImportant.

Wide Compatibility Gear puller fits Cummins VE, P7100, VP44, 4BT, 6BT pumps barring tool fit for Cummins BC Series pickups 3.9L-8.3L diesel engines.. Precision Fit Gear puller designed fit for 1989-2002 Dodge Ram Cummins injection pump gears, ensuring safe, damage-free removal.. Effortless Operation Gear puller removes pump gears quickly barring tool engages flywheel ring gear for easy timing adjustments use with 12 ratchet.. Premium Build High-strength carbon steel with anti-corrosion black finish, resistant to deformation for extended durability.. Complete Kit Includes 1x gear puller with 2 bolts 1x engine barring tool, ideal for professional repairs..

UNPARALLELED STRENGTH and STABILITY - Each Flywheel Removal Tool is Made Of Durable Steel with a Black Oxide Coating Ensuring Longevity and Durable Reliability For Long Lasting. PRACTICAL FEATURES - Flywheel Puller Set is Used to Separate The Flywheel From The Crankshaft Taper and Can Even Be Used to Pull Clutch Packs Permanently Laser-Etched with Metric Sizing. SPECIFICATIONS - Including Various Models 5 Single-Ended Pullers, M14xP1.5M16xP1.5M18xP1.5M13xP1.0M28xP1.5 5 Double-Ended Pullers M20xP1.0 M27xP1.25, M22xP1.0 M25xP1.5, M22xP1.5 M26xP1.5, M24xP1.0 M27xP1.0L, M26xP1.0 M28xP1.0. WIDELY USED - Suitable For The Vast Majority Of Motorcycles, ATVs Small Engines, Compatible with Honda, Suzuki, Kawasaki, Yamaha, Ducati, Arctic Cat. CONVENIENT STORAGE - For Your Convenience, We have Customized a Storage Box For Them Easy to Carry and Store Clear at a Glance Before Use.

Compatible withGZZTORES Flywheel Locking Tool for ChevyGM, LS1, LS2, LS3, LS6,clears all rear-wheel drive bellhousings-manual and automatic NOTEDo not work for Front-wheel drive engines. CompatibilityCompatible with GM 97 -2019 rear-wheel drive V8 LS and LT baised engines,Cars and trucks.4.8, 5.3, 5.7, 6.0, 6.2, 7.0 liter Will not fit Gen 3 coyote 18 and up engines. Durable Construction Made from high-quality 14 inch American cold rolled steel with a black anti-oxidation metallic paint to withstand the demands of professional automotive work. Essential Tool4 teeth for firm grip,perfect match,This is a great tool to help you complete your engine maintenance tasks quickly and efficiently. Package1PCS Engine Flywheel Locking Tool,2PCS proper length bolts.

Versatile Applications - The Flywheel Turner tool is suitable for various repair scenarios, including automotive transmission replacement, engine maintenance, outboard motor servicing, torque converter and flexplate replacement, as well as timing chain and cover replacement. It can also be used to position the flywheel for inspection and installation. Ergonomic Design - The user-friendly design ensures a secure grip on the flywheel without slipping, making it especially valuable for tasks like clutch replacements or engine rebuilds. Its adjustable feature accommodates various flywheel sizes, while the rubber-coated handle enhances grip and comfort during use. Additionally, the compact size allows for easy storage and transport, contributing to its overall ease of use. Adjusting Engine Position - This tool aids in accurately positioning the engine, which is crucial for various tasks such as timing adjustments, checking cylinder pressure, or disassembling specific engine components. Proper alignment ensures optimal performance and reduces the risk of errors during repairs. Rotating the Flywheel or Flexplate - The Flywheel Turner tool is specifically designed to engage with the teeth of the flywheel or flexplate, allowing you to manually rotate the component to the desired position. This facilitates precise installation or thorough inspection. Assisting with Bolt Tightening or Loosening - The Flywheel Turner securely holds the flywheel or flexplate in place, preventing any unwanted rotation. This stability simplifies the process of removing or tightening bolts, making it significantly easier and safer for you to perform your work. Trusted Service and Verified Quality - Buy with confidence from Bzcovac We aim to improve efficiency, save costs, and optimize time, allowing you to fully enjoy your pursuit of passion. Find your replacement parts here.

Versatile Applications - The Flywheel Turner tool is suitable for various repair scenarios, including automotive transmission replacement, engine maintenance, outboard motor servicing, torque converter and flexplate replacement, as well as timing chain and cover replacement. It can also be used to position the flywheel for inspection and installation. Ergonomic Design - The user-friendly design ensures a secure grip on the flywheel without slipping, making it especially valuable for tasks like clutch replacements or engine rebuilds. Its adjustable feature accommodates various flywheel sizes, while the rubber-coated handle enhances grip and comfort during use. Additionally, the compact size allows for easy storage and transport, contributing to its overall ease of use. Adjusting Engine Position - This tool aids in accurately positioning the engine, which is crucial for various tasks such as timing adjustments, checking cylinder pressure, or disassembling specific engine components. Proper alignment ensures optimal performance and reduces the risk of errors during repairs. Rotating the Flywheel or Flexplate - The Flywheel Turner tool is specifically designed to engage with the teeth of the flywheel or flexplate, allowing you to manually rotate the component to the desired position. This facilitates precise installation or thorough inspection. Assisting with Bolt Tightening or Loosening - The Flywheel Turner securely holds the flywheel or flexplate in place, preventing any unwanted rotation. This stability simplifies the process of removing or tightening bolts, making it significantly easier and safer for you to perform your work. Trusted Service and Verified Quality - Buy with confidence from Bzcovac You'll receive a brand-new product in its original packaging. We aim to improve efficiency, save costs, and optimize time, allowing you to fully enjoy your pursuit of passion. Find your replacement parts here. Technical Support - If you encounter any issues during installation or use, please feel free to reach out to us. We will respond to your email within 24 hours, providing installation guidance and necessary non-professional support please ensure our replacement parts are installed under the supervision of a qualified technician. We are also happy to listen to any concerns you may have. We hope you have a pleasant shopping experience with Bzcovac Store.

Wide Compatibility Tailored for Paccar MX-13 engines, including MX-11, this tool is specifically designed to accommodate Kenworth T880 and Peterbilt trucks, featuring a 12 drive for seamless operation.. Direct Replacement This tool serves as a direct replacement for OEM part numbers 1453158PE 1453158, ensuring seamless compatibility and functionality.. Heavy-Duty Construction Constructed from premium heavy-duty steel and subjected to heat treatment for increased hardness, this tool is engineered to withstand the rigors of professional use, ensuring unparalleled durability and reliability. Additionally, it is finished with a slick black coating, enhancing its resistance to corrosion and guaranteeing long-term performance even in the harshest conditions.. Easy to Use This tool is meticulously engineered for precise operation, ensuring efficient barring over the engine for hassle-free clutch adjustments. Its straightforward installation and operation make engine maintenance more efficient..

Folds for easy storage. Use this special wrench to turn the flywheel and rotate the engine. Also holds the flywheel or flex plate when torqueing the flywheel or harmonic balancer bolts. Included components Flywheel turner.

Fitment Flywheel remove tool is for most flywheels with steel adjustable timing hubs, PVL clone flywheel and raceseng flywheel with puller hole. Applicable Engine Predator 6.5hp 212cc OHV horizontal shaft gas engine not for hemi engine, GX160 GX200 6.5hp clone engine, for Harbor Freight. Compatibility Coleman CT200U CT200U-EX BT200X, KT196 CK196-T mini bike go kart, Axis M200, Massimo MB200, Trailmaster MB200, Baja Warrior MB165 MB200. Efficient Flywheel Remove Tool Compared with hitting the crankshaft with a hammer, using this tool to remove the flywheel is more convenient, labor-saving and avoiding damage to the crankshaft and flywheel. Installation Notices 1. Install the threaded screws into clean and lubricated puller holes, be sure to thread screws in fully. 2. Tighten the nuts evenly back and forth in 12 turn increments until the flywheel pulls off. 3. Stubborn flywheels may require that you hit the center of the puller block with a hammer once significant pressure is applied by tightening the nuts. Be careful not to strike the threaded rods and never hit the flywheel itself with a hammer. Note Pls check installation pictures if have problems on installation.

APPLICATION -- Set of 2 works on Any 1998-2007 for Volvo D12, D16 Engines 2008-2018 for Volvo Mack Truck, D11 D13 D16 MP7 MP8 MP10 Engines.. DIRECT REPLACEMENT -- OEM number references 9996956, 9996620 88800014. FUNCTION -- Special designed to rotate the flywheel of crankshaft for correcting the timing position. Help rotate your crankshaft with ease.. QUALITY -- Corrosion-resistant Quality Steel construction with extreme anti-wear property.. SATISFACTION GUARANTEE -- If you are not satisfied with Camoo products, simply return it for a full-refund in 30 days. Guarantee with 12 months warranty. No worry about buying.

Comprehensive Kit This harmonic balancer puller set makes removing and installing most press-fitted harmonic balancers and drive pulleys easy. It includes all necessary bolts and adapters for most applications, making it a comprehensive tool set for a wide range of jobs. Product Specifications This harmonic balancer puller kit includes bolts with threads 38-24 UNF, 38-16 UNC, 516-18 UNC, 516-24 UNF, 14-28 UNF, M10x1.5, M10x1.0, M8x1.25, and M6x1.0 for versatile compatibility. Wide Application This harmonic balancer puller set includes metric and standard bolts for flywheel, crankshaft pulley, and steering wheel removal. Note Not compatible with all vehicles, lacks M12x1.75 bolt, and not for LT1 Gen 2 or 4.0L Chrysler engines. Durable and Long-Lasting The harmonic balancer puller is made of high-quality, heavy-duty steel with exceptional strength and hardness. The surface is coated with an anti-oxidation coating to prevent rust, ensuring a long service life. Easy Removal and Installation This harmonic balancer kit removesinstalls balancers quickly and easily without damaging engine parts. Its thrust bearing design ensures smooth, even operation with minimal effort.

Replaces Flywheel puller with crank shaft protector 91-849154T1,Lifting Ring 91-90455-1. Function A must have tool when changing outboard motors on boats and lifting the engine off transom. Fitment For Most 45HP replacement for Mercury, replacement for Mariner, replacement for Force and replacement for Yamaha outboard motors with 1 12-16 TPI threads units from the 1960s to present. Size Please check the thread diameter, 1 12-16 TPI Threads Per Inch tool, 58-18 TPI Bolt and Lift Ring Threads. Package Include 1 Flywheel Puller Removal Tool with Crank Shaft Protector, 1 Lifting Ring.

ReplacesFlywheel puller with crank shaft protector 91-849154T1,Lifting Ring 91-90455-1. Size58-18 TPI Bolt and Lift Ring Threads. Usage scenarioA must have tool when changing Mercury outboard motors on boats and lifting the engine off transom. Anti-corrosion coatingmercury flywheel puller black oxidized finish to prevent rust, suitable for Marine environment. For Most 45HP Mercury, Mariner, Force and Yamaha outboard motors with 1 12-16 TPI threads units from the 1960s to present,but pls check thread diameter to verity.

FITMENT Perfectly fits for PACCAR MX, PACCAR MX PMCI-2, PACCAR MX-13 PCI and PACCAR MX-13 Engine Barring Flywheel Cranking Turning Tool. Commonly Used on Kenworth T880 and Peterbuilt Trucks. 12 Drive. REPLACEMENT Replaces 1453158PE 1453158. SUPERIOR MATERIAL Crafted from high standard Steel with black finish for great durability and superior protection, resistance to corrosion, providing a long-term service.. SATISFACTION GUARANTEE Yoursme aims to provide the best service for our customer and built to provide exceptional levels of durability, if you're not 100 satisfied with our item, simply return it for a full-refund in 30 days. We support 12 months' Warranty. If you have any problems about our products, please feel free to contact us..

Fitment Replaces 3824591A, 5299073, 7471A. Works for Selected B C series Diesel engines, and 3.9L, 5.9L, 6.7L, 8.3L liter turbo diesel engine used for Dodge pickups. 12 Drive. Function Suitble Barring Over the Engine to Make Clutch Adjustments, used to turn engineflywheel. For you to rotate an engine or turn the crank while performing valve lash adjustment, this tool makes the job easy.. Feature Adopting with super duty carbon steel and heat treated with black powder coated for durability and solid protection, anti corrosion and rust, no deform no fade. Well fit flex plate teeth to get friction-free use while rotating it in the housing, providing a longer service life.. Usage insert this engine barring tool into the flywheel housing until it engages the ring gear. Then attach a 12-inch square drive ratchet or breaker bar, and turn it to rotate the engine. Allows you to manually rotate an engine.. Package Include 1x Diesel Engine BarringRotating Tool with strict tolerance. Please check engine, part size and function before purchase..

SUPPORTED MODELS All two-stroke jet ski engines are compatible with our flywheel puller. In addition to being incompatible with Sea-Doo 787, 787 RFI, 800, 800 RFI, 947, 947 DI, 951, and 951 DI engines, nor compatible with Kawasaki 900, 1100, 1200 engines. CONFIGURATION DETAILS Flywheel Puller Tool x1. We pack professionally so that the Flywheel Puller will be free from bumps and wear and tear during transportation. It reaches you without any damage. MATERIAL USED The main body and key parts of the flywheel puller are made of special steel, which is very sturdy and can withstand the high-strength tension when removing the flywheel to avoid deformation or breakage. PRIMARY ROLE Our flywheel puller can safely remove the flywheel. Smoothly pulls the flywheel out of the engine crankshaft by applying an even force, avoiding damage to parts due to violent handling. CORE ADVANTAGES The material of the flywheel puller is specially treated, which is not easy to wear and rust in long-term use. Ergonomic design reduces the brute force required for disassembly.

Compatible with ChevyGM LS1, LS2, LS3, LS6 LSX Engine, to be used on engine mounts or in vehicles. NOTENot suitable for all-wheel drive engines.. Designed to work on engines already installed in vehicles. Works on all GM 97 -2019 rwd V8 LS and LT baised engines. Cars Trucks. 4.8, 5.3, 5.7, 6.0, 6.2, 7.0 liter NOT fit Gen 3 coyote 18 and up engines.. Simply bolt the starter into place and lock it securely to the flywheel teeth.. Welded using 14 US cold rolled steel with black coating, for strength and reliability.. Tools that must be had for cam or balancer replacement..

UNIVERSAL REMOVAL TOOLS This 3 jaw puller set by Orion Motor Tech fits your wrench or ratchet to work as a gear puller, bearing puller, crank pulley puller, flywheel puller and more, letting you easily handle worn or broken parts. BETTER TOGETHER Our bearing puller set includes three puller sizes, offering maximum spreads of 3, 4, and 6 and reaches of 4.3, 5, and 7.3 to cover most applications. 3 JAW DESIGN These power steering pulley pullers bite tightly onto your components with their reinforced jaws and distribute even pulling force to remove parts without causing damage. REVERSIBLE JAWS Each pulley removal tool can be reversed to pull parts from either the inside or outside, with the 6 gear puller provides 4 configurations for a sure grip thanks to its dual fixing holes. TOOLS FOR MECHANICS Drop-forged and heat-treated carbon steel builds with corrosion proof coatings ensure these pullers last for resilient service with unrivaled strength and durability.

Benefits -- Locks flywheel in place when removing harmonic balancer on 6.6L Duramax engines with Allison automatic transmissions. Saving time than removing the starter for water pump replacement.. Duramax 2500 3500 Pickups Use toothed pieces only removes metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel.. Duramax 4500 5500 Trucks -- Use toothed pieces with screws remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place.. 36mm Socket -- Use 36mm 12 point socket with 34 square drive to remove harmonic balancer bolt and re-torque on installation. 36mm 12 point socket can also be used on axle..

APPLICATION -- Used with 12 drive wrench. For Detroit Diesel DD13 DD15 DD16 MBE 4000 MBE 900, for Mercedes Benz Actros, Atego, Man 5, 6, 8-cylinder engines - D2528.. OEM QUALITY -- Comparable to the J-46392, W904589046300, W470589046300 Engine Barring Tool.. FUNCTION -- Designed to used with a 12 drive wrench to turn the flywheel and crankshaft manually.. MATERIAL -- Corrosion-resistant Durable Steel construction with extreme anti-wear property.. SATISFACTION GUARANTEE -- If you are not satisfied with Camoo products, simply return it for a full-refund in 30 days. Guarantee with 12 months warranty. No worry about buying.

APPLICATION -- Used with 12 drive wrench. For DD13 DD15 DD16 MBE 4000 MBE 900 Detroit Diesel, for Mercedes Benz Actros, Atego, Man 5, 6, 8-cylinder engines - D2528.. OEM QUALITY -- Comparable to the J-46392, W904589046300, W470589046300 Engine Barring Tool.. FUNCTION -- Designed to used with a 12 drive wrench to turn the flywheel and crankshaft manually.. MATERIAL -- Corrosion-resistant Durable Steel construction with extreme anti-wear property.. SATISFACTION GUARANTEE -- If you are not satisfied with Camoo products, simply return it for a full-refund in 30 days. Guarantee with 12 months warranty. No worry about buying.

Great Function Specially designed for flywheel fixing in the gearbox before removingdisassembling the engine.. Fitment Suitable for BMW N20old, N26old, N55 engine.. Feature For holding the flywheels on BMW engines N55, N20, N26 with automatic transmissions when loosening and tightening the pulley central bolt.. OEM Number Reference To be used as BM OEM 118660.. Satisfaction Guarantee - Yoursme aims to provide the best service for our customer and built to provide exceptional levels of durability, if you're not 100 satisfied with our item, simply return it for a full-refund in 30-days. We support 12 months Warranty. If you have any problems about our products, please feel free to contact us..

Fits most 14mm 2-cycle chainsaws including Husqvarna models 340, 345, 346, 350, 351, 353, 362, 365, 371, 372, 372XP, 385, 390, 390XP, 445, 450, 455, 455 Rancher, 460, 570, 575, 576, and more. Also works with Stihl, Echo, and other small engine chainsaws, trimmers, and blowers.. Package includes 1 piston stop tool, 1 clutch removal tool, and 1 clutch puller everything you need to disassemble the flywheel and clutch on 2-cycle chainsaws.. Replaces part numbers 502541601, 502541000, and 502541603. Perfect for clutch and flywheel service or maintenance.. Simply remove the spark plug and install the piston stop tool to hold the crankshaft in place. Tools are made from quality materials for durability and long-lasting performance.. Whether youre a small engine mechanic or a chainsaw owner doing your own maintenance, this tool kit makes clutch and flywheel service quick and easy..

Fitment Works on Cummins B C series diesel engines and 5.9L liter diesels. Quality Made of high quality-42CrMo Steel, to ensure great tolerance and resistance to corrosion and rust. Benefits Exclusively designed fits the flex plate teeth, the load-bearing collar provides friction-free operation while rotating the tool in the housing.. How to use Just insert the tool into the flywheel housing until it engages the ring gear, then attach a 12 square drive ratchet or breaker bar and turn.

Designed for 1.5 threaded flywheels, seamlessly compatible with most Non-Verado Mercury outboards. Includes AMT0022 Universal Lifting Ring adapters, engineered to replace OEM part 91-904551.. Built for engine removal, repowering, or maintenance tasks. Supports up to 1,000 lbs working load with reinforced load-bearing structure.. The tool with 1 12-16 threads. Fits most 45HP Mercury, Mariner, Force and Yamaha outboard motors. Outboard Lifting Ring Tool,Replace Part 91-904551, AMT0022, 18-9896.

Wide Range of Applications This adjustable pully holder is suitable for flywheel and clutch pulleys Wide application, universal for various motorcycle , which is practical to use. Superior Performance The flywheel holder is made of superior iron and rubber material, rugged, and has long durability Sophisticated production, provides excellent quality, very stable performance and high work efficiency. Well Made The Fly Wheel Holder has stable performance, manufactured for According to the original specifications Exquisite workmanship, stylish and generous appearance Conform to strict quality control, dependable to use. Easy to Use Compact size, lightweight and portable, easy to carry and convenient for using Ergonomic designed, easy to operate, high working efficiency, save time and effort. No Risk Purchase Our main goal is to make you have a happy purchase experience If you have problems, please tell us, and we will solve it as soon as possible.

OE Number ---- The referencing OE number of this locking kit is 09231 2B100, which is molded and designed depend on the original car data. Please double check the part number of your item, matching information is for reference only.. OE Number ---- The referencing OE number of this locking kit is 09231 2B100, which is molded and designed depend on the original car data. Please double check the part number of your item, matching information is for reference only.. Fitment ---- The engine flywheel holding is a repalcement for , repalcement for for more detailed information please refer to the parameters. We only use the highest grade materials, built to strict quality control standards. Every product must take inspected and tested multiple times before the shipment.. Features ---- This tool ensures the crankshaft is locked to allow the crankshaft pulley, clutch bolts and flywheel bolts to be removed and torqued without moving the crankshaft. You just need to bolt in place of your starter and locks securely into the flywheel teeth.. High strength steel ---- Engine Flywheel Locking Tool is used for timing chain and engine rebuild use, which is made of high strength steel, robust and , ensuring not easy to crack, scratch resistant, increasing product life.. Replacement ---- Engine Flywheel Locking Tool is made by exquisite processing and strict accordance with standard requirements, which have professional production, high precision and good reliability. replacement for your old or broken..

APPLICATION -- Suitable for BMW N20old, N26old, N55 engines.. FUNCTION -- For holding the flywheels on BMW engines N55, N20, N26 with automatic transmissions when loosening and tightening the pulley central bolt.. BENEFITS -- Designed to fix the flywheel in the gearbox before removing the engine.. REPLACE OEM -- To be used as BMW OEM 118660' For JTC-6670.. TOP QUALITY -- Heat-treated high-carbon steel construction ensures long-lasting performance. It delivers exceptional durability and proven to withstand heavy-duty tasks. Corrosion Resistance. Black coated offer superior rust protection to enhanced durability and a reliable finish, offering exceptional value.. SATISFACTION GUARANTEE -- If you are not satisfied with Camoo products, simply return it for a full-refund in 30 days. Guarantee with 12 months warranty. No worry about buying.

Use it to turn the flywheel and rotate the engine. Insert the spring loaded hook tip into the flywheel. Pivot tool handle to engage the handle tip in the flywheel.

Fits for Motorcycle ATV Scooter Dirt Bike Go Kart. Material The spanner wrench is made of high quality iron, which is not easy to bend. Flywheel Puller is made of magnetic steel ,surface phosphating antirust proc. With good manufacturing, fine workmanship and in reliable quality, it is durable and strong. Spanner wrench adjustable Screw, 2 sizes of pins, fit for different sizes of flywheel slots. Double Head Magneto Puller Size 24mm x 27mm. Package includes 1 Spanner Wrench , 1 Flywheel Puller.

High-quality Materials This flywheel puller is crafted from premium-grade metal, offering excellent adhesion, water resistance, and impact resistance, while withstanding high-temperature, low-temperature, and high-pressure environments. The product is resistant to aging and deformation and is not prone to breakage, ensuring long-term durability.. Easy to Use Simply clean the contact surface between the flywheel and the crankshaft. Align the suction end of the puller with the center of the flywheel or the designated suction point. Adjust the length of the puller rod or the thread depth according to the flywheel's thickness. Then, slowly and evenly turn the wrench, gradually increasing the pulling force until the flywheel is separated.. Easy Removal The flywheel puller utilizes a dual mechanism of suction and pulling to efficiently separate the flywheel from the crankshaft. This effectively reduces human error and minimizes the risk of flywheel slippage or tool dislodgement, significantly reducing the force required for operation. It is suitable for both manual and power-assisted use.. Wide Applicability This flywheel puller is compatible with most motorcycles on the market, fitting Gy6, CG25, JH70, SG50, and other 50cc150cc engines of equivalent dimensions. It accommodates flywheels of various sizes, further enhancing the tools practicality.. Packaging Upon purchase, you will receive 1 flywheel puller. This specialized tool, designed for motorcycle engine maintenance, has a total length of 3.15 and a top diameter of 1.06 ..

Function-- Clutch plate hub nut spanner tool designed to loosen and tighten the lock nut for the removal and installation of a motorcycle clutch.Another Used for removal of the flywheel or rotor if applicable.. Fits Flywheel Puller for GY6 50CC 125CC 150CC Yamaha Honda Suzuki KTM ATV scooter dirt bike Clutch lock tool for 50cc-125cc Honda Motorcycle ATV Dirt Bike Go Kart Pit Bike 4 Wheeler. Flywheel puller Size Material-- Stator magneto flywheel puller with 2 sizes24mm27mm Magnetic steel. Clutch lock Size-- Clutch lock tool Inner Diameterupper 20mm Inner Diameterunder 24mm Solid steel material. Package includes-- 1Magneto Flywheel Puller, 1Clutch lock tool.

Function--Remove your flywheel magneto rotor dynamo alternator generator stator and other uses.Essential tool to remove magneto flywheels without causing damage to crankshaft threads.. Usage-- Removes flywheels from ATVs,PWCs, motorcycles, lawn mowers, and chainsaws.. Size--Main Base Diameter 110 mm 4.3 inch. Material-- Iron. Package-- 1 Set Motorcycle Magneto Flywheel Puller Tool.

Chainsaw flywheel puller for Stihl 020T MS200T 026 MS260 028 030 031 032 036 MS360 038 MS380 041 044 MS440 045 046 MS460 MS280.. Chainsaw flywheel puller size is 22mm 26mm outside threads stator. Chainsaw clutch flywheel removal tool screw diameter 1.4cm 0.55inch, Material Metal.. for Motorcycles, Dirt Bikes, ATV Flywheel Puller Removal Tool. Compatible with Bosch. and for Stihl Echo 2 Cycle.. You will receive 1 x piston stop, 1 x clutch removal tool, 1 x flywheel puller chainsaw repair kit.. Welcome to contact with us before or after your purchase. Our warm responsible always be here for you..

Function-- Fits scooter magnetic motor, clutch and most straddle type motorcycle magneto demolition, the front and rear transmission gear of motorcycle and flywheel. Fits-- Adjustable Screw and two sizes of pin on either side make this spanner wrench suitable for different distances between slots and different sizes of slots.. Material-- High quality iron, can be long time using.. Size-- Total Length 29.7cm 11.7inch, Larger Pins diameter 9mm 0.315, Smaller Pins diameter 5.4mm 0.215, Arms Opening Width 15mm-120mm 0.6- 4.72. Package includes-- 1Flywheel Variator Clutch Spanner Wrench.

FITMENT This Engine Flywheel Locking Tool kit is compatible with all LS engines all GM gen III, IV, and V engines.. HIGH QUALITY Brand new, precisely manufactured from high-quality materials with Zinc coating, durable and long service time. Please rest assured that the latest products have been processed twice to prevent rust.. EASY INSTALLATION You just need to put the bolts in the corresponding holes and tighten them, only takes a few minutes.. PACKAGE INCLUDED It comes with one holding tool starter and two bolts FD 8.8, Pretty Tough New Design, Better than others.. A good handy tool can help you save time and money. We that it is tested before shipping. If you have any questions, please feel free to contact us for help and a Satisfactory solution..

10 pcs tool set servicing 15 different applications Please ensure the type of puller you need firstly such as size and LeftRight hand thread Except for M27x1.0, All pieces are right-hand thread. This motorcycle flywheel puller for most motorcycles dirt bikes ATVs. Package Includes 5 single-ended pullers M14 x P1.5, M16 x P1.5, M18 x P1.5, M19 x P1.0, M28 x P1.5 and 5 double-ended pullers M28x1.0 M26x1.0 M25x1.5 M22x1.0M26x1.5 M22x1.5 M27xp1.25 M20x1.0 M27xp1.0L M24x1.0for even more versatility. Made from quality steel surface covered with black oxide coating durable for a long time. Stay Organized Equipped with a sturdy and durable blow-molded casing, it is used for safe storage.

Why Need It The 10 pieces flywheel puller set can help you separate the flywheel from the crankshaft taper, and pull your clutch packs. Repair small engines on your motorcycle, scooter, ATV, mini bikes, metric bikes and dirt bikes, etc. Wide Applications Please ensure the type of puller you need firstly such as size and LeftRight hand thread. All pullers are right hand threads. 10pcs Different Size 5PCS single-ended pullers include M141.5, M161.5, M18P1.5, M19P1.0, M281.5 And 5PCS double-ended pullers include M20P1.0 M27P1.25, M22P1.0 M25P1.5, M221.5 M261.5, M24 P1.0 M27P1.0, M26P1.0 M28P1.0. High Quality Made from high-carbon steel, surface covered with black oxide coating, durable for a long time.

Fitment Crankshaft holder tool is for most engines with 34 crank, NOT for other size, pls check and note shaft size of your engine. Function No more struggling to hold the crank when torqueing a flywheel This tool slides over any 34 keyed crank and allows the flywheel to be torqued properly. It makes install the flywheel easier and saves time. How to Lock Tool The crankshaft holder tool locks into place through the long hole at the end, the 38 square hole allows you to use a ratchet or breaker bar to hold the crank for engines without the threaded holes in the sidecover. Durable Material Made of steel material, firmer and not easy to deform. Package List 1 crankshaft holder bracket, 1 aluminum hub, 1 keyway, 1 set nuts.

Firm lock the secure locking mechanism ensuring the flywheel remains stationary during repairs, offers dependable engineering crafted with meticulous precision, this ensuring stable operation,flywheel turner,flywheel turning universal flywheel locking. Ease of operation universal flywheel tool's user-friendly type makes flywheel locking quick and easy, improving efficiency,engine flywheel tools,flywheel locking adjustment tool universal flywheel locking tabs. Secure locking the tight locking mechanism ensuring the flywheel stays in place during maintenance,flywheel holder tool,flywheel holder. Precision manufactured with precise engineering, this tool provides consistent and reliable performance,camshaft flywheel locking tools,flywheel turner tool. Durability constructed from sturdy metal, this tool built to withstand wear and tear,flywheel holding ,flywheel holding tools.

Holds the flywheel in a locked position for servicing. Fits GM 6.6L Duramax Diesel, 2001 to present. Similar to J-44643.

COMPLETE KIT FOR ECOBOOST TI-VCT This 18PC timing tool set is engineered for Ford 1.6L2.0L EcoBoost, 1.6L Ti-VCT, and a wide range of DuratecDuratorq engines engine codes FYDA, HXDA, HWDA, also compatible with select Mazda 3 and Volvo models to provide a comprehensive solution for precise engine timing repairs and VCT system adjustment. PRECISION OE REPLACEMENT This kit ensures fit and OEM-level performance, directly replacing critical OE parts including VCT Setting Tool 303-1097, Camshaft Setting Bar 303-1552, Camshaft Positioning Plate 303-376B, Flywheel Locking Tool 303-393A, and other tools, for accurate camshaft, crankshaft, and timing component locking. VARIETY FIT This ford 3.5 timing tool kit enables confident repairs on popular models like Ford Focus 2004-2018, EcoBoostTi-VCT versions, Fiesta 2005-2017, 1.6L Ti-VCT, Escape 2013-2019, 2.0L EcoBoost, Fusion, C-Max, and Mazda 3 2004-2009, 2.0L Duratec, designed to work with specific engine codes such as FYDA, HXDA, HWDA for flawless timing alignment. DURABILITY ERROR PREVENTION These tools are forged from high-hardness carbon steel to resist wear and deformation, with precision machining ensuring accurate TDC Top Dead Center alignment, preventing costly valve timing errors and engine damage to safeguard your vehicle and avoid repair comebacks. READY-TO-USE Tools arrive with a light anti-rust oil film. This is a standard professional preservation measure, please wipe it off with a dry towel before use, while 18 components are organized, ensuring immediate use and long-term tool protection right out of the box.

Fitment Flywheel remove tool is for most flywheels with steel adjustable timing hubs, PVL clone flywheel and raceseng flywheel with puller hole. Applicable Engine This crankshaft hold and flywheel remove tool is a perfect tool for flywheel installation and disassembly. For Predator 6.5hp 212cc OHV horizontal shaft gas engine not for hemi engine, GX160 GX200 6.5hp clone engine, 212cc, for Harbor Freight. Note Crankshaft holder tool is for most engines with 34 crankshaft, not for other size, and make sure your flywheel has puller hole to use this flywheel puller. Flywheel Installation and Removal Tool This tool slides over any 34 keyed crank and allows the flywheel to be torqued properly. It makes install the flywheel easier and saves time. Compared with hitting the crankshaft with a hammer, using this tool to remove the flywheel is more convenient, labor-saving and avoiding damage to the crankshaft and flywheel. Installation Notices 1. Install the threaded screw into clean and lubricated puller holes, be sure to thread the screws in fully. 2. Tighten the nuts evenly back and forth in 12 turn increments until the flywheel pulls off. 3. Stubborn flywheels may require that you hit the center of the puller block with a hammer once significant pressure is applied by tightening the nuts. Be careful not to strike the threaded rods and never hit the flywheel itself with a hammer.

Mounts To Starter Bolt Flange. Color Natural. Material Aluminum. Use When InstallingRemoving Balancer, Flywheel, Torque Converter, And Lots Of Other Parts Or Bolts. Compatible with all GM gen III, IV, V, and all LS engines. Package Includes 1 Holding Tool, 2 Mounting Bolts.

Locks flywheel in place when removing harmonic balancer on 6.6L Duramax engines with Allison automatic transmissions. Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement. Use 36mm 12-point socket with 34 square drive to remove harmonic balancer bolt and retorque on installation. Package dimension is 4.5 inches width by 5 inches height by 2 inches depth.

Crafted from high strength steel,this tool features wear resistance and durability,ensuring it stays damage resistant over long use.. Perfect for use in professional marine repair shops for engine maintenance,outdoor boats upkeeps during docking,or projects home.. Its lightweight ensures easy portability and storage,making it a addition to any toolkit,suitable for various repair tasks beyond just flywheel removal.. The 91 849154T1 Flywheel Puller Removal Tool powerful pulling capabilities,allowing for quick and efficient flywheel removal,significantly enhancing repair efficiency for Outboards engines.. For boats maintenance technicians,or owners,and enthusiasts who enjoy boats repairs and maintenance..

Valuable BenefitsLocks the flywheel in place during the removal of the harmonic balancer for 6.6L Duramax engines equipped with Allison automatic transmissions, reducing time compared to removing the starter for water pump replacement.. 2500 3500 Flywheel HolderDesigned for use with Duramax 25003500 pickups. Install the toothed pieces by removing the metal spring-loaded inspection plate located on the bottom of the transmission. Slide the tool into the opening toward the engine, ensuring the top of the tool engages with the teeth of the flywheel.. 4500 5500 Flywheel HolderIntended for use with Duramax 45005500 trucks. Install the toothed pieces with screws after removing the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage with the flywheel, then hand-tighten the bolt to secure the tool in place.. 36mm SocketUtilize a 36mm 12-point socket with a 34 square drive to remove and re-torque the harmonic balancer bolt during installation. This socket can also be employed for axle maintenance tasks.. Efficient MaintenanceThis flywheel holder tool streamlines the process of removing and installing the harmonic balancer on engines. By securely locking the flywheel in place, it simplifies water pump replacement and other maintenance tasks, saving you time and effort while ensuring precise, stable operations..

Nitro Gas Engine Flywheel Remover Puller Tool Utility Wrench. for RC Car Buggy.

Applicable Engine Compatible with FORD Duratec petrol engine 1.25, 1.4, 1.6, 1.7, 1.8, and 2.0 twin cam 16V compatible FORD Duratorg diesel engine 1.4, 1.6, 1.8, 2.0 TDCI compatible with FORD ESCOBOOST 1.6 Ti-VCT, 1.51.6 VVT compatible with MAZDA PSA 1.4, 1.6HDI engine. engine code 1.25 16V DHA, DHB, DHC, DHD, DHH, DHG, F8JA, F8JB, FUJA, FUJB, M7JA, M7JB 1.4 16V ASDA, ASDB, FHA, FHD, FHE, FHF, FXDA C, FXDB D, FXJA, FXJB. Engine Code 1.6 16V FYDA C, FYDB D, FYJA, FYJB, L1F, L1J, L1L, L1N, L1O, L1T, L1V, L1W, HWDA, HWDB 1.7 16V MHA, MHB 1.8 16V EYDB, EYDC, EYDD, EYDE, EYDJ, EYDG, EYDI, EYDJ, EYPA, EYPC, RKA, RKB, RKF, RKH, RKJ, RKK 1.8 16V with control chain CDBB, CGBA B, CHBA B, CSDA, CSDB, QQDA, QQDB, QQDC 2.0 16V EDBA C, EDBB, EDBD, EDDB, EDDC, EDDD, EDDF, NGA, NGB, NGC, NGD 2.0 RS ST170 ALDA, HMDA 2.0 16V with control chain AODA, AODB, AOWA, CJBA B. OEM Equivalent Part Number This flywheel locking timing tool kit have 18pc tools, have everything you need for timing, replace OEM 303-1097 303-748 303-1550 303-1552 303-1054 303-1059 303-735 303-1552 303-393A 303-393-01 303-393-02 303-376B 303-651 303-193 303-507 303-734 303-732 303-xtra. Compatible with Vehicle for Focus 2004-2008 for Focus C-Max 2003-2008 for Mondeo 2007-2008 1.6 Ti-VCT 16V HXDA Diese engines for Duratorq Fiesta Courier 2000-2006 for Focus 1998-2006 for Focus C-Max 2003-2008 for Mondeo 2007-2008 for Tourneo Connect 2002-2008 for Transit Connect 2002-2008 for Fusion 2002-2008 for S-Max 2006-2008 for Galaxy 2006-2008 012 Ford B-Max 1.4L Duratec-16V 2015 Ford C-Max 1.5L EcoBoost. Fitment Vehicle 2011 Ford C-Max 1.6L EcoBoost, 1.6L Duratec-16V Ti-VCT13 - 14 Ford Fusion 1.6L EcoBoost 13 - 18 Ford Fusion 1.5L EcoBoost 14 - 16 Ford Transit 1.6L EcoBoostfor 03 - 05 Mazda MP 3.0L 04 - 06 Mazda Tribute 2.0L 2.3L 3.0L 04- 09 Mazda 3 2.0L 2.3L the timing tool kit compatible with Ford and Mazda vehicles with a wide range of modern, there are many models have not been written.

Part Number Manufactured according to strict original specifications, engine barring tool reference OEM numbers are J 46392, W904589046300.. Applicable Model Replacement for Detroit Replacement for Detroit MBE 4000 900 Replacement for Benz Actros Atego and more.. Function This tool is used to bar the engine over for service procedures, installs to engage the flywheel teeth and rotate the engine using standard drive hand tools.. Construction Made of carbon steel, which is rustproof, wearproof, impact resistant, not easy to break, and has high strength and durability.. Practical Tool Designed to adjust the engine for correct position. Used with 12in drive wrench. and trouble for years of use..

Exclusive Design The set is designed for quick water pump replacement. Locks flywheel in place when removing harmonic balancer on 6.6L Duramax engines with Allison automatic transmissions.. Time Saver Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement. Easy to install and effectively keep the flywheel from turning.. Easy to Use Locks the flywheel easily to the transmission when changing water pump. The flywheel locking tools work with Duramax 2500 3500 pickups and 4500 5500 trucks.. Heavy Duty Comes with flywheel holder OEM no.AM-J-44643-A, AM-J-44643-B, and 36 mm 12 point socket. Constructed of quality CR-V Steel with a manganese phosphate coating to resist rust and corrosion.. 126 MonthDurable products backed by an extraordinary 126 months warranty..

Compatible with B-riggs S-tratton Number19069. Size Holes on puller 1-58 Center to Center ,Bolt Length 2-12 Inches ,Bolt 14-20 Thread. This Part fits too many models to list. 090602-0111-B8, 091202-0150-01, 091202-1210-E1, 091212-0004-01, 091212-0193-01, 091212-1302-E1, 091232-0067-01, 091232-0203-01, 091232-1207-E1, 091232-1369-E1, 092232-0007-02, 092232-1238-E1, 093232-0540-01, 093302-0188-E1, 093312-0142-E1, 093312-1182-B1, 093332-0136-E1, 093332-0184-B1, 093332-1156-B1, 093412-0039-01, 093432-0035-01, 093432-1036-E1,. Usage steps 1. Disconnect the power supply of the motor and let it cool down to room temperature. Clean the oil stains around the flywheel and mark the relative position of the flywheel and the crankshaft. 2. Align the adapter with the center hole of the flywheel, and screw the pull rod clockwise until it is tightened. Fix the counterweight arm onto the crankshaft gear, and alternately tighten the two side nuts. 3. Slowly rotate the central screw. If there is resistance, gently tap the edge of the flywheel to assist in loosening..

MODEL FITMENT For use on all two stroke jet skis engines EXCEPT, for Sea-Doo 787, 787 RFI, 800, 800 RFI, 947, 947 DI, 951 and 951 DI engines, for Kawasaki 900, 1100, 1200. INCLUDED IN PACKAGE Flywheel Puller Tool 1, making it the perfect addition to your toolbox for efficient, hassle-free repairs and maintenance. EFFICIENT FLYWHEEL REMOVAL Ideal for flywheels with three off-center threaded mounting bolts for the puller. If your model uses different holes, a simple M18x1.5 bolt will be required for smooth flywheel removal. PREMIUM TOOL Built with durable, long-lasting materials, this tool is designed for effective flywheel removal on 2-stroke jet ski engines. AFTER-SALES SUPPORT Please verify that your vehicle model is compatible with GOLKNHA product. We offer a 1-YEAR warranty. If you have any questions, our 247 CUSTOMER SERVICE team is always here to assist you..

Locks flywheel in place when removing harmonic balancer on 6.6L Duramax Engines with Allison automatic transmissions. Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement. On 2500 and 3500 pickups, remove metal spring-loaded inspection plate on the bottom of the transmission. For more information check the main Lisle tool- 22100. Replacement part for Lisle tool- 22100.

Compatible for 6.6L Duramax engines with Allison automatic transmissions.. Materior All components made of CNC steel, surface black coated with great rust and corrosion resistance, excellent solid and durable.. Work with Duramax 4500 5500 trucks.Remove the rubber inspection cap on the bottom of the transmission.Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place.. Forged 36mm socket Use on the balancer bolt.Use with a 34 square drive wrench,Locking the flywheel at the transmission instead of having to remove the starter for water pump replacement.. Work with Duramax 4500 5500 trucks.Remove the rubber inspection cap on the bottom of the transmission.Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place..

Peace of Mind Keep your flywheel in place when removing a harmonic balancer with this flywheel lock, so you can focus on the task at hand worry-free. No Extra Steps If you need to replace your water pump, lock your flywheel with this flywheel locking tool set instead of removing the starter to save time and simplify your work process. Everything You Need The flywheel locks come with a 36MM 34 drive 12 point socket, making it simple to remove and reinstall the harmonic balancer bolt during your projects. Set It and Forget It For Duramax 25003500 vehicles, the toothed attachment quickly locks the flywheel Remove the inspection plate to align the lock with your flywheel. Tightly Fastened For Duramax 45005500 vehicles, the toothed piece with its included fastener is easy to hand-tighten once the teeth are aligned with the flywheel.

Will fit on most Stihl Chainsaws, Trimmers, Blowers, etc....

MULTIFUNCTION - Allowing unit to be used with harmonic balancer, flywheel, crankshaft, steering wheel, pulley and other two or three hole applications.. HIGH-QUALITY - All components are crafted from heat treated carbon steel with oxide finishes, helping the tool withstand tough pulling jobs and resist rust.. COMPATILIBIYTY - Includes 30 different bolts and a four-yoke slot, can handle a range of jobs on most cars, trucks, SUVs and small engine vehicles.. PACKAGE - Comes with a heavy duty blow molded carrying case, for easy transportation, safe storage and quick organization.. 100 SALE SUPPORT -We back up all products for life, 247 fast response customer service free all your concerns. Sincerely thanks for your support to Thorstone.

Fitment -- This flywheel locking tool designed for various vehicles flywheel turner, it fits for Renault MOT582-01, fits for Peugeot, fits for Citroen 0153A, 6012T, 9765.54, fits for BMW 119260 and mini cooper S, fits for Mercedes 607589014000, fits for Honda K series, fits for Fiesta ST, fits for Fiesta ST, fits for Buick 3, fits for GM LS engine and more.. Function -- This car flywheel timing tool mesh with the flywheel teeth pretty well to lock and hold the flywheel securely, allow you to carry out the operations of setting the timing, dismantling the damper pulley etc.. Superior Quality -- Made from high standard carbon steel which can withstand corrosion, rust and impact, its solid construction ensures an unparalleled long lifespan.. Easy to Use -- Our flywheel locking tool features an elongated bolt hole. Just bolts through one of the transmission mount holes and locks securely into the flywheel teeth.. Save Time and Labor -- User-friendly type makes flywheel locking quick and easy, highly efficient save your time..

Function--- Engine Timing Tool Kit Set Timing Belt Tool For FORD MAZDA. Suitable for a wide range of modern Ford and Mazda vehicles.. Wide Compatibility--- Engine tools are compatible with a large range of Ford vehicles B-MAX, C-MAX, Cougar, Courier, EcoSport, Escape, Fiesta, Focus, Focus C-Max, Fusion, Galaxy, Ka, Kuga, Mondeo, Puma, S-MAX, Tourneo Connect, Tourneo Courier, Transit, Transit Connect, Transit Courier.. Package Includes---This engine timing belt tool set includes reinforced OEM replacement camshaft and flywheel locking tools, crankshaft pulley alignment tools, a camshaft sprocket puller, a camshaft alignment plate, a camshaft setting bar, as well as all the pins required for locking other various parts of your engine.. High Quality Material---Made of high quality heavy duty steel and corrosion-resistant longevity. These tools' heat treatment and reinforced construction ensure robust and long-lasting help for safely fixing all your vehicle's timing difficulties.. Accurate---All tools have undergone rigorous engine testing, we use precise processing technology to ensure the accuracy of products, specialized, so trusted..

Application -- Engine Timing Tool Kit Set Timing Belt Tool For FORD MAZDA. Suitable for a wide range of modern Ford and Mazda vehicles.. Usage -- To lock andor position camshaft, crankshafts and time belt tensioners, as well as for adjusting the VTC unit.. Fitment -- Ford flestacourier 2000, focus 1998-2000, focus 2004-2008, focus c-max 2003-2008, mondeo 2007-2008 Ford 1.8 D TDCI. Package includes -- Camshaft and flywheel locking tools various timing pins plus a camshaft sprocket removal tool.. Convenient -- Heavy-duty blow-molded plastic carrying case for quick transportation, simple storage, and organization..

VERSATILE APPLICATIONS Bushing Bearing Race and Seal Driver Tool for Cars and Motorbikes. MAIN FUNCTION Special designed for checking and adjusting of engine timing and align and lock the camshaft in TDC position properly. FEATURES This tool kit is by forged high carbon steel. Heat treatment would help the tool kit achieve high hardness and and good wear resistance, which can provide a longer service lifetime. PACKAGE INCLUDING 1pc Flywheel Locking Tool ,1pc Inlet Camshaft Locking Tool, 1pc Exhaust Camshaft Locking Tool. TIPS Please check the vehicles information or tool information before purchasing, welcome to contact us if you have any questions.

Fits 1998-2018 Volvo Trucks All Models VN VNL VNM VHD D11 D12 D13 D16 Engines and 2008-2018 Mack Trucks All Models MP7, MP8, MP10 Engines. Turning over engine, makes adjusting injectors and valve lash easier. Exclusively designed fits the flex plate teeth, the load-bearing collar provides friction-free operation while rotating the tool in the housing. Needn't to manually rotate an engine. Use with a 12-Inch square drive ratchet or breaker bar. Package included 1Volvo truck engine barring socket 1998-2008 and 1 Volvo Mack truck engine barring socket 2008-2018.