FITMENT Compatible with Mercury Outboard Motors 1994 and Later. OEM PART NUMBER87-88107 , 87-88107A5, 7-1155. PREMIUM QUALITYMade of high quality marine-grade glass-filled polyester, non-conductive housing eliminates potential shorts circuits. Marine pushbutton switches with chokes offer maximum protection against corrosion. SPECIFICATIONRated Up to 30 A 12V. Compatible with Side Mount Controls or Panels up to 58. SERVICEAUTOBABA offers 1 year product quality support to our customersIf you are uncertain of any problems, please contact us.

This ignition switch key assy for remote control box fits Yamaha Marine 2 4 stroke outboard models. Compatible with Yamaha International 6 8 9.9 13.5 15 25 30 40 48 50 55 60 70 75 80 85 90 95 100 115 130 140 150 175 200 225 240 250 300 HP. Also suitable for Yamaha International VMAX 2002-2013 and Yamaha Outboard 225 250 HP 2003. Replaces Yamaha 703-82510-40, 703-82510-41, 703-82510-42, 703-82510-43, 703-82510-44, 703-82510-45 and Sierra MP51040, MP51042. This key ignition switch assy is made of high-quality plastic, which makes it wear-resistant and maximizes strength and durability. Easy to install, no tools required, the wiring diagram is also included in the package.

Replace lgnition Key Switch - The boat ignition switch need to be replaced when you have to turn the key hard and the boat won't launch. Our boat lgnition switch with choke has great corrosion protection to eliminate oxidation. And the non-conductive housing of ignition key can prevent potential short circuit to extended service life.. Replaces Part Number -This 6 wire boat ignition key switch fits for most Mercury Outboard Motor Control Box, replaces for Mercury OE PART NUMBER 87-17009A5, 87-17009A2, mp51090, MP41070-2, MP41070-1. Please check the ignition switch part number carefully before you purchase.. Feature - This Boat Engine lgnition Switch has 2 keys, 6 wires for push to choke, and 3 position Offignition -Start. And it is made of high quality polyester and brass, the boat inition switch with key has an excellent Corrosion resistance, Abrasion resistance and Conductivity.. Easy lnstallation -- The color of the lgnition switch wire matches factory color code, so it is easy toinstall push choke ignition switch, just match the wire color to install. Note This ignition key switch is nota genuine Mercury part, it's a direct replacement and meets OEM standards Quality.. Service -- our ignition Switch comes with one year warranty. lf you have any questions about our Mercury boat lgnition Key Switch, please feel free to contact us. We are always here to support you..

FitmentThis engine starter ignition key switch fit for Mercury Outboard Control Box, Replacement for Mercury 87-17009A2, 87-17009A5,for Sierra MP41070, MP41070-1 MP41070-2. Please carefully confirm your part number before purchasing to ensure that this marine Ignition Key Switch is what you need.. High Quality MaterialThis boat ignition switch is made of high-quality ABS plastic and brass materials. The combination of ABS plastic's insulation properties and brass's high conductivity ensures the safety and reliability of the ignition switch. Additionally, both materials offer excellent corrosion resistance, making them highly suitable for use in the damp, high-salinity marine environment.. Easy to InstallOur marine ignition switch has a simple installation process. The color coded wiring matches perfectly with the factory color code, simply inserting and replacing wires by matching their color, simplifying the installation process.. FunctionThis marine engine ignition switch comes with 2 keys, features a 6-wire design supporting a push-to-choke function, and has 3 positions Off - Ignition - Start. Pull-push type choke function suit for magneto type ignition switch, making the engine easier to start.. Package Included 2 x Keys,1 x Boat Ignition Switch..

Boat Ignition Switch with Key High quality boat ignition switch with key 6 wire is made of marine-grade glass-filled polyester construction, durable in use. Boat Ignition Key is non-conductive housing eliminates potential shorts. Boat key switch with choke has maximum corrosion protection - eliminates oxidation. Ignition Switch Boat Push to Choke 6 Wire Base Mercury - inner seal between cylinder lock and contact plate. Fitment 6 wire boat ignition fits for Mercury applications wPotted Wires replacing OE's Listed - 6 wire marine ignition switch replaces for Mercury part number 87-88107, 87-88107A5, 7-1155. Boat Ignition Switch with Key 6 Wire fits for most Mercury Outboard Motors 1994 and Later using. Specification Push choke ignition switch has 3 Position Off - Ignition - Start, includes 2 keys, fits for Side Mount Controls or Panels up to 58. Boat Ignition Switch with Choke rated Up to 30 amps 12V. Ignition Key Switch with Push to Choke function, use with Magneto Ignition. Warranty 1x Ignition Key Switch, 2x Key - we offer 24 month warranty. If you have any other questions on our Boat Engine Ignition Key Switch, please contact us at the first time, We are always here to support you. We provide free service of REPLACEMENT or REFUND, you can buy our 6 wire ignition key switch with confidence. Note Please check the pictures of this boat ignition switch with key and compare boat ignition switch with key 6 wire with your part number carefully to make sure this push to choke ignition switch for boat is what you want before you purchase.

Compatible with129572 Ignition switch with key Compatible with Tracker Boats. Package Included 1 Ignition Key Switch with Wire Connector adapter, 2 Keys.. Position 3 positions Off-Ignition-Start,Ignition Key Switch with Push to Choke function, use with Magneto style ignition switch.It is used for the marine mercury outboard motor control box. Easy to install, no soldering or splicing.. Boat Ignition Switch with Key The boat identity switch is made of high-quality materials.. Note Please check the pictures of this boat ignition switch with key and compare boat ignition switch with key 6 wire with your part number carefully to make sure this ignition switch for boat is what you want before you purchase.

FITMENTCompatible with OMC Johnson Evinrude 40-200HP Outboard Motors. OE PART NUMBER5005801 175974. PREMIUM QUALITYMade of high-quality plastic and metal, ensuring resistance to aging and wear. It maximizes strength and durability for long-term use. Reliable quality and service will deliver an excellent user experience. COMPLETE KITIncludes a water-resistant ignition switch, 2 keys, and a safety lanyard, ensuring reliable engine startstop and emergency shutoff capability. EASY INSTALLATIONMatches factory wiring and mounting design, enabling a quick swap without modificationsideal for DIY repairs or professional servicing.

Ignition switch for most OMC inboardoutboard applications. Push to choke feature eliminates need for separate choke switch. Terminals 6. Size 2-764 inch x 1-2964 inch. Includes two keys.

Marine ignition switch for marine mercury outboard control box. Easily replace damaged mercury ignition switches with this exact replica, no soldering or splicing required. Ignition switch replaces most Mercury outboard control boxes, reference model Mercury 87-17009A5. Three-position ignition switch, 6-wire, marine ignition switch is made of high-quality materials, with good safety, durability, and good conductivity. Package includes, 1 six-wire ignition switch, 2 keys.

3-Position Off Run Start. 78 mounting hole with easy wiring to screw terminals. Universal fit for cars, motorcycles, buggies, mowers, go karts and more. Supplied with two keys. Rated 10A at 12vDC.

Higher compatibilty This ignition key switch fits most Mercury Outboard Control Boxes, Replacement Mercury OE Part No. 87-17009A2 87-17009A5, Sierra MP41070-2 MP41070-1 MP41070 Please double check the fitment for your motorized boat before purchasing to better help you.. Simple and quick installation our marine ignition switches have 2 push buttons, a 3-position design off-run-start and 6 wires for the choke function, and the wires of this marine engine ignition switch are color-coded to match the original factory color-coding, which makes your assembly more efficient and more convenient. Replacement Marine Ignition Switch with Key Our marine ignition switches are made of high performance polyester and high quality brass materials for superior durability and conductivity. It is the switch that starts and shuts down the motorized boat and is the main electrical system used to control the starting of the motorized boat.When you find that the engine won't start when you twist or turn the key hard, then you may need a new marine engine ignition key switch.. Package includes 1 x marine ignition switch, 1 x switch key cap. Professional after-sales service We provide One year warranty. If you have any questions or concerns about our marine engine ignition key switch, please feel free to email us, we will always provide you with 100 satisfactory after-sales service..

Application This ignition switch fits for Marine and Boat.. Marine Ignition Key Switch Part Number Si-erra MP39060-1, Se-achoice 50-11621, Cole Her-see M550 M550BPBX M550BX.. Position 3 Terminals Operation Mode Off-Run-Start Voltage 12V Current 15A.. Material The ignition key switch is made of brass material for durability.. Package Includes 1 x MP39060-1 Marine Ignition Switch, 2 x Keys. TIP The key will be a little hard to turn the first time you use it, try several attempts or use a lubricant..

100 Brand New and High Quality.Ignition Key Switch with Push to Choke function. Replaces for Mercury part number 87-88107 , 87-88107A5, 7-1155. Fits Most Mercury Outboard Motors 1994 and Later using. 3 Position Off - Ignition - Start,includes 2 keys.Fits for Side Mount Controls or Panels up to 58. Rated Up to 30 amps 12V.Direct Replacement..

Outboard Kill Stop Switch Cord Our universal boat lanyard is equipped with 7 keys that can be installed on all kill switches, making it perfect for Mercury, Yamaha, Honda, Tohatsu, Johnson, Evinrude, Suzuki jet skis. Features The boat safety lanyard kill switch, also known as the engine cutoff switch abbreviated as ECOS, ensures that your engine automatically shuts off in emergency situations. Superior Material Outboard kill switch lanyard is made of PU rope and high-quality ABS plastic clip. It is manufactured according to strict quality control standards. This safety lanyard is not easily damaged and can extend its service life. Moreover, It is a cord with elasticity. Effective Alternative Choosing our universal seven key lanyard can better meet your different needs without worrying about the type of lanyard, as it is suitable for most boat jet skis. Function When the mooring line is pulled up, the switch will turn off, the engine will stop, the ship will slow down, and then stop, effectively avoiding the occurrence of the story and protecting your safety. After Sales Service When you have any other questions about our products, or if the product you purchased does not meet your expectations, we are always ready to solve your doubts. We wish you a pleasant shopping experience.

Replacement Ignition Starter Switches The engine starter ignition key switch need to be replaced when you have to turn the key hard but the boat won't launch. Easy Installation Colors on switch wires match factory color codes. Direct replacement, a simple plug play with no wire splicing. Meets or exceeds OEM standards, 100 tested before shipping. Please check the pictures of this boat ignition switch with key and compare boat ignition switch with key 6 wire with your part number carefully to make sure this push to choke ignition switch for boat is what you want before you purchase. Professional Design This Boat Engine Ignition Switch has 2 keys, 6 wires for push to choke, and 3 position which made of polyester and brass, durability and excellent electrical conductivity. Inner seal between cylinder lock and contact plate, the maximum panel thickness is 58 inches, which is suitable for side-mounted controls or panels up to 58. Rated Up to 30 amps 12 V. Direct Replacement. Ignition Key Switch with Push to Choke function, use with Magneto style ignition switch. High Compatibility This Ignition Key Switch replacement for most Mer-cury Outboard Control Box, replace OE number for reference Mercury 87-17009A2 87-17009A5, Sierra MP41070-2 MP41070-1 MP41070. Please kindly check the fitment to ensure this will fit your model before ordering. Package Included 1 x 87-17009A5 Boat Ignition Switch, 2 x Keys.

Replacement Part Number Compatible with Yamaha outboard yacht switch panel, part number 704-82570-12-00 704-82570-08-00 704-82570-01-00 Single key switch panel suitable for Yamaha 2-stroke and 4-stroke mechanical shift outboard motors. Function Push the main switch to the air damper, with air damper switch and engine warning buzz. Your boat ignition switch is an important part of the starting process. It is connected to the starter through the boat's 12V system. Easy Installation The panel is easy to install only four screws are needed to secure the panel, the wiring harness is installed in place, and the emergency stop switch is installed at the top of the panel. Superior Materials The main switch panel single engine key switch panel is made of high-quality metal and plastic, with stable performance and high reliability, making it a perfect substitute Single Key Switch Panel. Assembly A switch panel, two keys, and four screws, as well as an external single engine switch panel assembly including warning horn and connector wiring harness. Size 110mm x 70 mm or 4.3 inch x2.8 inch. After Sales Service When you have any other questions about our products, or if the product you purchased does not meet your expectations, we are always ready to solve your doubts. We wish you a pleasant shopping experience.

77 Series Switch.

Applicable ModelsCompatible with Mercury Marine Quicksilver Outboard Motor.Please refer to the product description below for detailed model data.. Replace Part Number87-897716K01 897716 8M0059686.In order to fit your boat perfectly and save you time,please carefully check your boat model and part number before purchasing.. Suitable Durable Crafted with premium materials and rigorously tested to meet strict quality standards, our product provides a perfect fit for your boat while maintaining durability and reliability in the long term.. Satisfied serviceWe will provide 12-month after-sales service. We are committed to providing excellent customer service to our customers, if you have any questions, please feel free to contact us. We will do our best to make your shopping experience perfect.. Package Contains1x Ignition Key Switch WHarness. 1x key.As shown in picture.

4 Position Ignition Switch Design Designed as a replacement for Sierra MP41040 marine ignition switch. Features ACC-OFF-RUN-START operation for reliable engine starting and ignition control.. Corrosion Resistant Construction Built with corrosion-resistant materials and a brass back-up nut to help withstand moisture, salt spray, and harsh marine environments.. Protective Rubber Cap Features a rubber cap design to help reduce exposure to water mist, spray, and outdoor marine conditions.. Reliable Electrical Control Provides dependable ignition and accessory control for compatible marine electrical systems.. Suitable for Marine Applications Ideal for replacing worn, damaged, or corroded ignition switches on boats and marine equipment..

REPLACEMENT IGNITION STARTER SWITCHES - An ignition switch, starter switch or start switch is a switch in the control system of a motor vehicle that activates the main electrical systems for the vehicle. If you have to wiggle the key hard or the boat won't start when the key is turned, it means you need to replace a new engine starter ignition key switch for your boat.. PROFESSIONAL DESIGN - 3 Position OFF - RUN- STAR and 6 wires for push to choke. This Boat Engine Ignition Switch made of high performance polyester and high quality brass, which provides safety, durability and excellent electrical conductivity. You can buy it with great confidence.. COMPATIBILITY - This Ignition Key Switch replacement for most Mercury Outboard Control Box, replace OE number for reference Mercury 87-17009A2 87-17009A5, Sierra MP41070-2 MP41070-1 MP41070. Please kindly check the fitment to ensure this will fit your model before ordering.. EASY INSTALLATION - Colors on switch wires match factory color codes. Direct replacement, a simple plug play with no wire splicing. Meets or exceeds OEM standards, 100 tested before shipping. Please kindly check the fitment to ensure this will fit your model before ordering.. 24-MONTH WARRANTY - Order from SKARUMMER, we offer 24 month warranty. If you have any other questions on our Boat Engine Ignition Key Switch, please contact us at the first time, We are always here to support you. You can buy it with confidence..

Marine-Grade Durability Heavy-duty stainless steel boat ignition switch with corrosion-resistant housing, brass terminals, and flame-retardant plastic. Built to last as a boat ignition switch in harsh marine conditions.. Superior Conductivity Three high-quality brass terminals ensure a secure connection. This marine ignition switch delivers smooth operation and consistent starts, ideal as a reliable starter ignition key switch.. 3-Position Function Standard Off-On-Start mode. The 3 position ignition switch fits 12V systems, 20mm mounting hole, and panels up to 34mm thick.. Universal Fit Designed as a versatile boat main switch ignition compatible with most outboard ignition switch applications. Simple replacement for your old boat key switch.. Complete Kit Package includes 1 ignition switch and 2 keys..

Premium Replacement Ignition Switch 5005801 175974Brand new ignition key switch with safety lanyard, designed for Johnson, Evinrude OMC 40-200HP outboard motors. Direct plug-and-play installationno wiring modifications needed.. Push-to-Choke Emergency Cut-Off SafetyFeatures a push-to-choke function for easy cold starts. The safety lanyard instantly kills the engine if detached, preventing accidents in emergencies.. Heavy-Duty Construction for Marine UseMade of high-grade plastic metal for corrosion resistance and long-term durability. Meet the OEM standards for reliable performance in harsh marine conditions.. Complete Kit with 2 Keys Extended LanyardIncludes 1 ignition switch, 2 keys, and a 49.2 125cm safety lanyard. The extended length ensures easy attachment to life vests or boat operators.. Hassle-Free Warranty SupportBacked by a 1-year warranty and 247 customer support. If you have any issues, contact us for a quick solution or replacement..

Application This ignition starter switch fits for most Si-erra and mer-cucy, Accommodates 58 Panel, Magneto.. Boat Ignition Switch Replace Part Number Si-erra MP41000 MP52000 Mer-cucy 87-88107 87-88107A5 17393 88107 S-EA-Dog 420381-1.. Features Push-to-choke, polyester housing with rust and corrosion resistance.. Specification Terminals 6 Positions 3 Operation Mode Off-Run-Start Rated Choke 7 Amp 12v DC Rated Ignition 15 Amp 12v DC Rated Solenoid 30 Amp 12v DC.. Package Includes 1 x MP41000 Marine Ignition Switch, 2 x Keys..

Direct Replacement Design Designed as a replacement for Sierra MP39770 marine ignition switch. Features OFF-RUN-START operation for dependable engine starting and ignition control.. Corrosion Resistant Construction Built with corrosion-resistant materials and a brass back-up nut to help withstand moisture, salt spray, and harsh marine environments.. Protective Rubber Cap Design Features a protective rubber cap to help reduce exposure to water mist, spray, and outdoor marine conditions.. Reliable Ignition Control Provides dependable ignition and starting control for compatible marine electrical systems.. Suitable for Marine Applications Ideal for replacing worn, damaged, or corroded ignition switches on boats and marine equipment..

Compatible with Yamaha 704 Control Box This single engine key switch panel is compatible with Yamaha outboard 704 control box systems using a 10-pin wiring harness. It fits many 2-stroke and 4-stroke mechanical shift outboard motors. Please confirm your original plug and part number before purchase.. Replacement Part Numbers Designed to replace 704-82570-08-00, 704-82570-11-00, and 704-82570-12-00 key switch panel assemblies. A practical replacement for a worn, cracked, loose, or failed marine ignition switch panel.. On-Off-Start Key Operation The marine ignition switch panel supports standard On-Off-Start key control for single engine operation. It helps restore reliable starting and shut-off control when the original switch panel is damaged or not responding properly.. Easy Direct Installation Pre-drilled mounting holes and screws are included for easier installation. The 10-pin plug design helps simplify replacement without complicated rewiring, saving time during boat or yacht maintenance.. Package Package includes 1 key switch panel, 1 key, 1 wire harness, and 4 screws. Single engine key switch panel, compatible with Yamaha. This single engine key switch panel was not created by Yamaha. Brand names and part numbers are used only to show compatibility..

Premium Quality Made of quality brass and exquisite technology, wear-resistant and corrosion-resistant, stable performance and long service life. All the items have passed strict quality inspection before shipment. Replace Part Number MP39060-1, 50-11621. Fitment Wide application, fit for Marine and Boat. Easy to Install Strictly according to standard specifications and dimensions. Plug and play, easy to install. What You Get 1 x Ignition Switch, 2 x Keys. Please carefully check the part number before purchase.

Single Engine Key Switch When you have a cracked ignition switch panel, failed keys, and poor wiring harness contact, you may need to replace the key ignition switch panel to ensure optimal performance. Quality Outboard Switch Panel AFEISOL main switch panel is made of premium alloy, which is effectively waterproof and dustproof, corrosion and vibration resistant. And also has stable performance even in harsh marine environments, provides reliable On-Off-Start functionality. Switch Panel Assembly Outboard single engine switch panel assembly includes 1 main switch panel, 1 key, 1 pc 10pin harness and 4 screws. Plus an emergency stop button, voltage 12 v. power 0.1 w. choke by pressing main switch, with choke switch and engine warning buzzer. Easy Installation The panel is easy to install, just install the wiring harness in place, the panel requires four screws to secure it, and the emergency stop switch is mounted on top of the panel for stopping the engine in the event of an emergency. Compatibility AFEISOL main switch panel compatible with Yamaha single vertical control yachts, replace OE 704-82570-12-00, 704-82570-11-00, 704-82570-08-00. Ensures seamless integration with original 704 control box systems with strict control of manufacturing. Safety User-Friendly Design Outboard key switch features a secure key-lock mechanism to prevent accidentally miss. Waterproof Main Switch Panel design enhances durability and operational safety.

This Key Ignition Switch Assy for Yamaha 2 4 Stroke Outboard Motors meets or exceeds OEM specifications. Fits for Yamaha Outboard 225 250 HP 2003, Yamaha International 6 8 9.9 13.5 15 25 30 40 48 50 55 60 70 75 80 85 90 95 100 115 130 140 150 175 200 225 240 250 300 HP 1998-2013, Yamaha International VMAX 2002-2013. Replaces Yamaha Outboard Part 703-82510-44-00 703-82510-43-00 703-82510-42-00 703-82510-11-00. Easy to Install, No Tools Required. Connect the original cable, pull on the protective sleeve, and tighten the nut, then complete the installation. Made of High-Strength Polyoxymethylene Material and High-Quality Pure Copper Core, Durable. Sealed Glue Process, Waterproof, Dustproof and Insulation.

Perfectly compatible Designed for Yamaha outboard yacht switch panels direct replacement for 704-82570-12-00, 704-82570-11-00, 704-82570-08-00. Single-key switch panel suitable for two-stroke and four-stroke mechanical-shift outboard engines.. Package Contents 1 Main Switch Panel, 1 Key, 1 10-pin Wiring Harness, 4 Screws. Additionally, includes an emergency stop button 12V, 0.1W, and a choke activation feature when the main switch is pressed featuring a choke switch and engine warning buzzer. Dimensions 110 mm x 70 mm or 4.3 inches x 2.8 inches. Plug-and-play, quick 10-minute installation Comes with a standard 10-pin wiring harness simply plug the harness into place and secure the panel with 4 screws. No additional modifications or wiring adjustments are required, making installation easy and hassle-free.. High-quality materials, long-lasting performance The panel body features a composite structure of high-quality alloy and high-strength plastic, providing effective protection against water, dust, corrosion, and vibration. It will not rust or degrade in performance even when used in environments with prolonged high humidity or salt spray. The key-locking mechanism is reliable and durable, preventing accidental power loss and ensuring every start-up is safe, stable, and long-lasting.. After-sales service and purchase guarantee This product comes with a 1-year unlimited mileage quality guarantee. During the warranty period, if any quality issues arise, we will provide free repair, replacement, or technical support. Buy with confidence, enjoy a reliable user experience, and have no concerns..

This Key Ignition Switch Assy for Suzuki Outboard Motors meets or exceeds OEM specifications. Fits for Suzuki 2-Stroke Outboard DT 8 9.9 15 20 25 30 35 40 55 65 75 85 90 100 115 140 150 175 200 225 HP 1983-2003, 4-Stroke Outboard DF 9.9 15 25 30 40 50 60 70 140 HP 1996-2011. Replaces Suzuki Outboard Part 37110-99E02 37110-99E01 37110-99E00 37110-92E02 37110-92E01 37110-92E00. Easy to Install, Connect the original cable, pull on the protective sleeve, tighten the nut, then complete the installation. Made of High-Strength Material and High-Quality Pure Copper Core, Durable. Sealed Glue Process, Waterproof, Dustproof and Insulation.

Good Replacement Push to choke ignition switch is used to replace and refurbish the original ignition switch to improve the ignition performance. High-Quality Materials This bass tracker ignition switch is made of high-quality ABS plastic and brass metal materials, which are sturdy, durable, waterproof, and highly reliable. High-Quality Materials This bass tracker ignition switch is made of high-quality ABS plastic and brass metal materials, this for evinrude ignition switch is sturdy, durable, waterproof, and highly reliable. Manufacturer Part Number 50-11651 ignition switch. Wide Adaptability The boat ignition switch is widely compatible with most OMC inboard and outboard powered boats for motor control.

Replacement Replace 6E9-82575-00 6E9-82575-01 6E9-82575-02 65W-82575-00 65W-82575-01 Sierra 18-65450. Suitable for Yamaha Mercury Tohatsu Mercruiser marine engine motor. Please check the replacement model before placing the order. Premium Material Boat emergency kill switch cord is made of PU rope and excellent ABS plastic clips, It is manufactured according to strict quality control standards. It is lightweight, convenient, and easy to use and it is 3.5 inch coiled and stretched is extend to 48 inch. Essential Lanyard Emergency safety lanyard is used to cut off the power or ignition of the engine, which is not foolproof, but designed to allow the motor to run when the switch is damaged and cannot be touched for some reason such as corrosion. How to Install When pulling the hanging rope, the switch will come into contact or close, so the switch must be closed in order to turn off the motor. Tip When sliding the plastic key under the device, pull out the parking device of the boat. Function With this boat engine switch lanyard, you won't be trapped in the water due to a faulty switch. Please make sure to regularly test the switch to ensure it works properly. After Sales Service When you have any other questions about our products, or if the product you purchased does not meet your expectations, we are always ready to solve your doubts. We wish you a pleasant shopping experience.

Excellent Material Ignition switch with key is made of high-performance gumwood material with good insulation, heat and corrosion resistance, and high strength. The four studs are made of copper-plated iron for excellent electrical conductivity and safety. 4-Position Design Ignition switch is a 4-position design with Ign, Bat, Acc and Start functions, which control the 4 operations of Battery-Ignition-Accessory-Start respectively, ensuring the forklift and vehicle starting system to function properly and provide a stable and safe starting experience. Product Information Package includes an ignition switch with key replacement, 2 keys and 4 hex nuts. The switch measures 3.03 inches x 1.7 inches, is specified for use with a DC12V power supply, and is rated at 30A. Ideal for automotive applications where reliable starting is required. Easy to use Equipped with a screw locking nut, this starter switch connects wires easily to the right studs. No ground needed for the switch, but your loads connected to the switch need to be grounded. Simple key turn for starting or off, ensuring a quick and reliable vehicle start. Widely Used Key switch is compatible with a wide range of vehicles including cars, trucks, SUVs, tractors, trailers, forklifts, etc.Suitable for both agricultural and industrial applications.Ideal for 12-volt vehicles, it offers a wide range of solutions for industrial and commercial applications.

INTRODUCTION Brand new ignition switch and key assembly with safety lanyard, compatible with OMC Johnson Evinrude 40-200HP outboard motor, in line with original factory specifications.. PART NUMBER Replacement of outboard motor assembly 175974, 5005801 Use this kit to repair your boats ignition and starting system quickly. Easy to install, just simple plug and play.. HIGH QUALITY The ignition switch assembly is made of high-quality plastic and metal, not easy to age and wear-resistant, and can ensure the maximum strength and durability, so that it can be used for a long time. Reliable quality and service will bring you a wonderful use experience.. PACKAGE INCLUDE 1ignition switch and key assembly with safety lanyard.. WARRANTY 100 Service. We Promise the Premium Quality and the Best Service, One-year warranty and 247 Professional Customer Service Technical Support. Contact us freely if have any questions. If You are Not Completely Satisfied with Your Purchase Simply Let us Know and Youll be Offered Replacement, No Questions Asked. Enjoy this Absolutely RISK FREE Purchase..

Versatile Compatibility Compatible with Yamaha multiple part numbers 704-82570-11-00, 704-82570-12-00, 704-82570-08-00, ensuring a perfect fit for Yamaha outboard motors.. Easy Installation Designed for quick and hassle-free installation, this key switch panel fits seamlessly with Yamaha 2-stroke and 4-stroke outboard motors that have a 10-pin wiring harness, saving you time and effort.. Premium PerformanceCrafted with high-quality materials, this boat ignition switch panel kit ensures long-lasting durability and dependable performance, making it ideal for harsh marine environments.. Comprehensive Control Equipped with clear indicator lights and user-friendly controls, this panel offers comprehensive engine monitoring and management, keeping you informed of your engines status at all times.. Enhanced Security Provides a secure ignition system to prevent unauthorized use, giving you peace of mind when your boat is unattended..

Compatible With This ignition switch is compatible with Mercury Marine and Quicksilver outboard motor boat engines, ensuring seamless integration for marine starting systems.Notesnot fit 2006.. Replace OE This ignition key switch replaces OE part numbers 87-897716K01, 897716, and 8M0059686, making it a direct-fit replacement part.. High Quality This 897716K01 ignition switch is constructed from marine-grade materials, ensuring excellent water resistance, durability, and long-lasting reliability in harsh boating environments.. Function This 3-position ignition switch Off Ignition Start provides smooth engine start-up and is designed to maintain consistent electrical connection under marine conditions.. Package include 1 Boat Engine Ignition Key Switch with pre-attached harness, 1 ignition key.

FITMENTCompatible with Yamaha outboard yacht switch panel. Compatible with Yamaha 2-stroke and 4-stroke mechanical shift outboard motors. OE PART NUMBER704-82570-12-00 704-82570-08-00 704-82570-01-00. PREMIUM QUALITYMade of high quality metal and plastic, stable performance and high reliability to ensure long term usage. EASY INSTALLATIONEasy to install, just four screws to secure the panel, install the wiring harness, and the emergency stop switch is mounted on the top of the panel. PACKAGE INCLUDED 1 x Switch Panel, 2 x Key, 1 x Wire,4 x Screws.

Boat Key Lanyard you will get 4 pieces of red boat kill switch lanyards, they can be applied to cut off the powerignition of the outboard engine. kill switch lanyard the outboard kill switch lanyard is made of quality plastic Very strong but lightweight, durable quality can be applied for a long time And it is very convenience to carry. boat safety lanyard the length of the safety lanyard is 59 inch when uncoiled, coil extendable lanyard with swivel snap hook, which can prevent tangles. How to use you can fix the plastic end under the boat lanyard kill switch, and then tie the other end to your hand Pull down the switch lanyard in an emergency, the engine power on the ship will be disconnected Safety note Do not overtighten when tying to hand or fixed point. Fits for most outboard engine this outboard switch lanyard is very convenient to use and can handle emergency situations It is a stop switch lanyard cord, the switch fits for most brand outboard engine.

Strong and durable.. Easy to install.. Please confirm whether suitable before buying.. Product number 703-82510-43-00, 703-82510-42-00, 703-82510-44-00, MP51040. fit For Yamaha Outboard 75-85-115-150HP 703-82510.

Replace Part Number 176408. Ignition cut off switch replacement for for Johnson BRP Evinrude boat motor.. Material This single engine ignition key switch made of premium quality ABS, PVC and metal for durability and reliability.. Easy to Install This engine ignition starter cut off switch comes with pre-drilled mounting holes and mounting screws for easy installation. Mount and secure to the appropriate location in the control box, then connect the wires. The wiring is designed with clasp, plug and play. However, professional installation is strongly recommended.. Performance This boat kill switch is characterized by high precision, moderate weight, no stopping due to vibration.. Flexible Strap This outboard ignition switch lanyard is expandable and flexible. It is flexible and elastic with a swivel hook that prevents tangling. And it is very convenient to carry..

Package Included 1 Ignition Key Switch, 2 Keys. High Quality Boat ignition switch with key 6 wire is made of marine-grade glass-filled polyester construction to ensure reliable performance and long service life, trustworthy quality. Function Boat Ignition Key is non-conductive housing eliminates potential shorts. Boat key switch with choke has maximum corrosion protection - eliminates oxidation. Replacing number for reference 87-88107 , 87-88107A5, 7-1155. Fits Most Mercury Outboard Motors 1994 and Later using. Position Off - Ignition - Start,includes 2 keys. Ignition Switch Boat Push to Choke 6 Wire Base Mercury - inner seal between cylinder lock and contact plate.The maximum panel thickness is 58 inches, which is suitable for side-mounted controls or panels up to 58.Rated Up to 30 amps 12V.Direct Replacement. Ignition Key Switch with Push to Choke function, use with Magneto style ignition switch. Easy install.Colors on switch wires match factory color codes. Direct replacement, a simple plug play with no wire splicing. Meets or exceeds original standards, 100 tested before shipping. Please check the pictures of this boat ignition switch with key and compare boat ignition switch with key 6 wire with your part number carefully to make sure this push to choke ignition switch for boat is what you want before you purchase.

The bottom has 6 clearly labeled terminals simply connect the corresponding wires, making installation easy.. Size 2-764 inch x 1-2964 inch. Ignition switch for most OMC inboardoutboard applications. The materials used in the switch structure are relatively sturdy, have corrosion-resistant properties, and have a long service life.. Includes two keys.

Product Specifications The product package includes 1 ignition switch and 2 keys. Ignition switch diameter is 1.65 inches and its height is 1.77 inches. Please check product size before purchasing boat ignition switch with key. Easy to Install First find the original ignition position, remove the screws and buckles, then insert ignition start switch into the socket and clamp. After restoring power supply, insert key ignition switch key again for testing. Easy to Use Ignition key switch 6 wire ignition has 2 gears, one on and one off. Compared with other 3- and 4-gear switches, ignition key switch is easy to use, not easy to touch by mistake, and can bring better using experience. Plastic and Metal Switch starter ignition key is made of metal and plastic materials, which is sturdy and has a long service life. Ignition key switch 6 wire ignition start has stability and can meet your long term use needs. Scope of Application 6 Wire ignition key switch is suitable for 2.5-6.5KW 188F cars, boats, bicycles, tractors, trailers and other fuel generators. Switch key starter can also be used as a replacement for your old ignition switch.

Replace Part Number The Heavy Duty Marine Ignition Switch is suitable for MP39060-1. Fitment The Ignition Switch has wide applicability and can be used in automobile switch, ship switch and so on. Great Performance The Ignition Switch is made of brass material, the use of exquisite technology and quality testing, so that it has good performance at the same time the structure is stronger, better durability, longer service life. Package Includes 1MP39060-1 Heavy Duty Marine Ignition Switch. 2 Keys. Please compare the specific applicable models listed at below to make sure it'll fit.

Tilt Trim Switch Body with brass back-up nut and hex black plastic, with Off-Ignition-Start 3 positions.. 7-1150 Replaces 87-88107A5 Replaces for Mercury 87-88107 and 87-88107A5.. Fit for most Mercury applications.. Accommodates 58 panel, Weatherproof cover included.. Package Includes 1x Boat Ignition Switch with 2 Keys..

Heavy duty three-position offignitionstart switch. Plastic construction ensures maximum corrosion resistance. Max Panel Thickness Up to 1-18 inch. Terminals 3. Includes two keys. Manufacturer part number 50-11641.

Hole Size 78 Rated Ignition 15 Amp,12v DC Rated Solenoid 30 Amp, 12v DC. Replace Part Number 87-88107, 87-88107A5, 87-17393, 87-88107, 87-88107A5, 420381-1. Fit Type Universal fit. Features Push-to-choke, maximum corrosion protection, inner seal between cylinder lock and contact plate, non-conductive housing eliminating potential shorts, 20 Amp rating. Package Included 1 x Ignition Switch, 1 x keys.

Engine Position Outboard. Replaces Part OEM Number 176408 0176408. This items Include the Ignition Switch Keys Wires, as show on the picture.. If you are unsure, please provide your engine serial number.. fits Johnson BRP Evinrude 176408 0176408 Single Engine Ignition Starter Cut Off Switch With Keys.

MARINE ENGINE IGNITION SWITCHMarine Ignition Switch Engine Ignition Kit for Mercury, when you turn the key and find that the engine won't start, you may need a replacement ignition key switch for your marine engine. HIGH QUALITY HOUSINGThe six-wire ignition switch with key is made of marine-grade fiberglass and the locking cylinder is made of premium quality pure copper to ensure reliable performance, waterproof as well as rust-proof, long service life and high quality. PUSH SWITCHThis 87-17009A2 ignition switch adopts 3-position press design, off-run-start, more convenient to use, with six wires connected externally that can be pressed to the choke, superior quality and waterproof, dustproof and insulated. EASY INSTALLATIONThe switch wiring color of the marine engine ignition key switch is the same as the original color code, it is directly replaceable, plug and play, no additional wiring is required, please check carefully whether the relevant wiring is the same at the time of purchase. APPLICABLE MODELSMarine switch key replacement OE numberFor Mercury 87-17009A5, 87-17009A2, 17009A2,for Sierra MP41070-2 MP41070-1 MP41070, please make sure your model number matches before purchasing.

BEST IN CLASS PRODUCT. Fit type Universal Fit. Oem equivalent part number OMC 393301.

Back Up Nut Brass. Inner seal between cylinder lock and contact plate. Maximum corrosion protection - eliminates oxidation. Non-conductive housing eliminates potential shorts. Face Nut Knurled Black Plastic with Rubber Cap.

Ignition switch for most OMC inboardoutboard applications. Push to choke feature eliminates need for separate choke switch. Terminals 6. Size 2-764 inch x 1-2964 inch. Includes two keys.

BEST IN CLASS PRODUCT. Fit type Universal Fit.

BEST IN CLASS PRODUCT. Fit type Universal Fit. Compatible with vehicle type off-road-motorcycles.

Sierra products are engineered to meet todays high horsepower engine demands and stand up in the harsh marine environment. All Sierra products meet or exceed the original equipment part it replaces. Sierra supplies many OEM engine manufacturers and boat builders hundreds of quality parts every day.. Backup Nut brass Face Nut knurled black plastic. Hole Size 78 Length short 1-18 maximum panel thickness. Rated 15 Amp 12 VDC. Terminal Type 4 Screw Tab. Fit type Universal Fit.

Impact- and corrosion-resistant switch fits standard 78 inch dia. Hole and includes PVC boot for added weather protection. Nominal voltage is 6-36v DC. Rated for 15a ignition, 5a start. 8-32 screw terminals. Fits panels upt to 78 inch thick. Replaces Cole hersee part number m-850.

Back Up Nut Brass. Inner seal between cylinder lock and contact plate. Maximum corrosion protection - eliminates oxidation. Non-conductive housing eliminates potential shorts. Face Nut Hex Black Plastic.

4 Position Starter Switch Acc.-Off-Ignition-Start. Includes two keys and a boot. Stem Width 1316. Ignition 15 Amps 12V. Solenoid 13 Amps 12V.

Heavy duty three-position offignitionstart switch. Brass construction ensures lasting durability. Max Panel Thickness Up to 1 inch. Terminals 3. Includes two keys.

Push to choke. Maximum corrosion protection - eliminates oxidation. Inner seal between cylinder lock and contact plate. Non-conductive housing eliminates potential shorts. Hole Size 78.

Kit includes switch, 50-inch coiled lanyard and disconnect clip. Universal fit. Black nylon casing. Rating 5A at 12V. Protective clear package for easy visability and application. Manufacturer part number 50-11681.

AUTOMOTIVE REPLACEMENT IGNITION STARTER SWITCHES The replacement for mercury outboard ignition switch is made of quality material. Make it reliable and wear-resistant to use. FITMENT FOR BOAT KEY LANYARD IGNITION SWITCH The ignition switch and key assembly with lanyard replacement for Johnson ignition switch, for evinrude ignition switch, for omc ignition switch. Quality boat kill switch suitable for evinrude motor. REPLACE NUMBER FOR BOAT KILL SWITCH IGNITION The marine ignition switch with key boat ignition key replacement number 175974 5005801 357868. Designed to directly fit the original factory oem one. FEATURE FOR MARINE KEY SWITCH The replacement for mercury outboard key motor assembly is easy to install, strong and flexible enough to use. Plug and play, direct fit for the oem ignition. BUY WITH CONFIDENCE You'll get 1 pc tracker boat ignition switch, 1 pc ignition switch key and 1 pc kill switch lanyard.

Professional Designcompatible with Mercury Outboard Remote Control Box 3 Position OFF-RUN-STAR and 6 wires with push to choke. Replaces OEM Numbers87-17009A5 87-17009A2 Sierra MP41070-2, MP41070-1, MP41070 , MP51090. Easy InstallationFactory-matching wire colors for direct replacement, no splicing needed, 100 tested before shipping. Reliable Performance6-wire ignition switch with keys features marine-grade fiberglass housing and a premium pure copper lock cylinderwaterproof, rustproof and durable. Package Include1 x ignition key switch, 2 x keys.

Compatibility AFEISOL boat ignition key switch safety lanyard assembly compatible with Johnson Evinrude OMC 40-200HP outboard motors ignition switch and key assembly, this ignition key switch with safety lanyard provides perfect replacement and reliable engine starting for boats. Replace Part Number Ignition switch key assembly with safety lanyard replacement for 5005801, 175974. Strict quality control, our marine ignition switch with key lanyard is reliable and trustworthy, ideal ignition key switch replacement for outboard motor kill switch. Enhanced Safety With a quality safety lanyard that ignition key kill switch cuts off power if in the event of an accident, the marine ignition key switch is designed to prioritise the protection of the user. Premium Material Great value ignition switch and key safety lanyard are manufactured from premium quality materials, which are designed to reliably ignite and shut down the engine, and provided high durability, reliability and safety for you. Easy to Use Directly replacement ignition kill switch key lanyard is very easy to use, just plug and paly. With extendable safety lanyard allows for flexible use, more user friendly. You Will Get 1 x boat ignition switch, 2 x ignition switch keys and 1 x ignition kill switch safety lanyard. If you have any questions about this ignition key switch safety lanyard assembly, we always be here to help you.

Replaces Single Ignition Key Switch Panel Part OEM Number 37100-96J24 37100-96J25. If you are unsure, please provide your engine serial number.. Engine Position Outboard.

Waterproof Marine-Grade Primarily designed as a reliable ignition switch for boats, this 12V 10A marine ignition switch comes with a heavy-duty, sealed waterproof rubber boot. It provides superior protection against saltwater spray, humidity, and engine compartment elements, ensuring dependable starts for yachts, speedboats, and personal watercraft.. Universal Practical Functioning as a versatile universal key switch, it features a standard OFF-ON-START 3-position operation. The set includes 2 identical stainless steel keys, making it an ideal direct replacement ignition switch for a wide range of marine and vehicle ignition systems. Wide-Ranging Application Beyond marine use, this robust ignition switch replacement is also compatible with cars, trucks, ATVs, UTVs, and tractors. It serves as a direct upgrade for automotive electrical system switches, engineered to withstand vibration and harsh conditions across various environments. Simple Installation Designed for convenience as a direct replacement ignition switch, its standard 3-terminal design and universal mounting pattern allow for a simple, wire-for-wire swap in most boat and vehicle ignition systems, significantly reducing installation time. Complete All-in-One Kit This comprehensive kit provides everything needed to restore ignition function 1x ignition , 2x spare keys, and 1x waterproof sealing boot. It is the trusted solution for fixing a faulty ignition key switch on both water and land.

1.Compatibility This ignition key switch replacement fits most marine outboard control boxes. Reference replacement OE numbers 87-17009A2, 87-17009A5, Sierra MP41070-2, MP41070-1, MP41070. Please check the fitment carefully to ensure this will fit your model before ordering.. 2.Replacement Marine Ignition Switch with Key Marine ignition switch engine ignition key switch kit, 3-position Off-Run-Start design, suitable for DFI, EFI MPI outboard motor control boxes.. 3.Details This Boat Engine Ignition Switch is made of high performance polyester 6 wires for push to choke and high quality brass, which provides safety, durability and excellent electrical conductivity. Sealed glue process,Waterproof, dustproof and insulation.Long service life.. 4.Easy installation Our marine ignition switch has 2 push buttons, 3-position design OFF-RUN- START and 6 wires for choke function, and the wire color coding of this marine engine ignition switch is the same as the original factory color coding, which makes your assembly more efficient and convenient. 5.Package Includes including 1 pc 3-position boat ignition starter switch, and 2 pc ignition keys..

Replace Ignition Key Switch The engine starter ignition key switch needs to be replaced when you have to turn the key hard but the boat won't launch. Our boat ignition switch with choke has corrosion protection to eliminate oxidation. Easy Installation Colors on switch wires match factory color codes. Direct replacement, a simple plug and play with no wire splicing. Meets or exceeds OEM standards, suitable for boat owners, DIY enthusiasts, and maritime aficionados, even non-professionals can install it within 10 minutes. Professional Design This boat engine ignition switch has 2 keys, 6 wires for push to choke, and 3 position Off, Ignition, Start. Made of polyester and brass for durability and excellent electrical conductivity. Inner seal between cylinder lock and contact plate, the maximum panel thickness is 58 inches, which is suitable for side-mounted controls or panels up to 58 inches. High Compatibility This ignition switch with key is compatible with Mercury OE PART NUMBER 87-17009A5, 87-17009A2, mp51090, MP41070-2, MP41070-1. This boat ignition switch perfectly matches the original factory interface for seamless compatibility. Please check the ignition switch part number carefully before you purchase. Package Contents Package includes boat ignition switch and 2 keys. Constructed with durable materials to withstand marine environments and provide reliable performance for your boat's electrical system.

Replace Part Number The heavy duty marine ignition switch Replace MP39060-1 50-11621. FitmentThe ignition switch fit for 15Amps 12Volts 3 Position automotive and marine switches. Product SpecificationsPositions 3 TerminalsOperation Mode Off-Ignition-Start Voltage 12V Current 15A Mounting Hole 78'' Max Panel Thickness 1 18''.. High Quality Brass MaterialThe ignition switch is made of high-quality brass material, which has excellent corrosion resistance and rust prevention performance, can effectively resist the erosion caused by seawater, has excellent conductivity, ensures stable ignition signal transmission, can maintain good performance in frequent starting and closing operations, is not prone to faults, reduces maintenance costs, and ensures the normal operation of the ship.. Easy to InstallThis marine ignition switch is easy to install, simply remove the old ignition switch and replace it with a new one, without the need for complex installation steps. Pay attention to matching the wiring with the terminals on the ignition switch during installation.. Package Include1 X Ignition Switch, 2 X Keys..

This Marine Ignition Switch and Key Assembly with Safety Lanyard Replacement for OMC Johnson Evinrude 40-200HP Outboard Motors. Replaces part numbers 5005801 175974. Please verify fitment and part number before purchasing. Made of premium plastic and metal for reliability, safety, durability, and excellent conductivity, ensuring long-lasting performance. Features a safety lanyard that attaches to the operator's life vest or wrist. If the operator falls overboard, the engine shuts off immediately, protecting both the person and the boat. Simple plug-and-play design for quick and hassle-free setup. Package Contains 1 X Ignition Switch, 2 X Keys, 1 X Safety Lanyard. Contact us if you encounter any issues or need assistancewere here to help.

Brand new, Evinrude Johnson OMC BRP Ignition Key Switch with Safety Lanyard.. Push to choke. Replaces Yamaha part 5005801, 175974. This trim switch meets or exceeds OEM specifications. Direct aftermarket replacement with a simple plug play design.

Replace part number 37100-96J24, 37100-96J27, 37100-96J25. Fitment Replacement for Suzuki outboard engines.. Features Ignition switch panel will not turn off from vibration, stable performance, dependable to use.. Package Content 1x single engine ignition key switch panel, 2 keys, 1x switch panel, 1x safety lanyard and 4x screws. If you are unsure, please provide your engine serial number..

4 Positions ACC OFF RUN START. Universal fit for car, truck, tractor, trailer, forklift, and more. Designed with a screw lock-nut for through-panel mounting. Studs are labeled for easy wiring Battery-Ignition-Accessories-Start. Supplied with 4 x ring crimp terminals.

sturdy and durable made of high-quality plastic and well-conductive pins ensure long lasting durability,highly optimized for general use and will give you a pleasant experience.. idea replacements 5 pin on-off rocker switch with spst design single pole single throw, simple installation, freely turn on or off the light. the switches can be replaced with any defective 5 pin spst switches.. wide application standard 5 pin switch, rated at 20amp12vdc and 10amp24vdc, available for upgrading most wiring harness to control led light bar, led work lights, fog lamps, headlights, taillights and auxiliary lamps, etc.. diy stickers products also shipped with 1 pcs of diy sticker and 1 pcs of night glow sticker with various patterns, can be diy used to control any vehicle electrical appliance for your specific needs.. package include 6pcs rocker switches, 6 sets of jumper wires, 2 pieces of diy stickers. 2 Year Warranty.

Compatible with Johnson Evinrude Boat.. Replaces Part number 5005801, 175974.. Use this kit to easily and quickly repair you boat ignition and starting system.. Easy to install, just simple plug and play.. Warranty For any reason, if you are not satisfied with your purchase, please contact us directly. We offer a one-year warranty, 100 satisfaction guarantee..

Brand New Aftermarket 3 Position Brass Ignition Switch. Durable,High Performance. From Top Quality Manufacturer,Strict Quality Control. Fulfillment by Amazon. One Year Warranty.