Ultimate Protection The remote battery disconnect switch easily solves the problem of battery drain but also protects the circuit, No matter how long your car is parked, The battery always has a full charge. The battery is via the remote switch, which also reduces the risk of theft occurs.. Premium Quality Remote battery kill switch Instantaneous current of up to 450A rated current of up to 250A. Our remote battery kill switch is made with high-quality materials and pure copper wire, modules have larger rivers for better reception performance and can extend car battery life by 3 - 4 times.. Effortless Installation Our upgraded remote battery kill switch for cars is designed to directly disconnect the negative switch, fix the battery clip to the negative pole of the battery, and connect the red wire to the positive pole of the battery, our upgraded version reduces a black power cord, making installation simpler than other products.. Versatile Use Our 12V remote kill switch for cars is suitable for cars, trucks, RVs, travel trailers, campers, motorcycles, and any other engine application with 12-volt batteries. Please note that disconnecting the positive terminal may damage the battery and vehicle circuit.. Reliable Quality If it cannot be used normally after installation, please check whether the circuit is installed normally or send a message to contact us, quality after-sales service is provided to go to meet any of your needs. If you have any questions you can email us and we will get back to you within 24 hours..

COMPATIABLEThis knife-blade battery disconnect switch is suitable for TOP POST TERMINAL, battery NEGATIVE post only. Maximum Current 750A, Rated Current 250A. 6v 12v 24v car truck, bus, RV, Boat, trailer battery. TOP LEVEL HEAVY DUTY This top post battery disconnect switch is made of brass material, corrosion resistance, conductive performance is good, durably made for safety use. EASY TO INSTALLThis battery doctor knife switch for top post batteries can be adjusted into a vertical knife switch through the bottom of the screw, easy to install simple to use. Switch the knife, then power will cut. SAVE ELECTRYCITYThis knife blade master switch is used for the battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, stop unwanted battery drain and prevent theft or unauthorized use. Widely used for car, truck, boat or RV battery, also other electrical equipment's battery. BUY WITH CONFIDENCE We are so confident you'll think we have the satisfied battery disconnect switch on the market. If you have any problem about our product, please feel free to give us a message and we will do anything for you to make the thing right. We go out of our way to make sure every customer is happy and satisfied with our product and service..

High QualityA ABIGAIL Side Post Knife Blade Master Switch is made of Heavy Duty solid brass which is rust and corrosion resistant, durable made for safety use. Note Please Do Not choose the Material of brass plated with copper. OperationBattery Disconnect Switch is OnOff 2 position, with a long bolt, used for side post terminal, battery side post with 38 hole only, DC 12V-24V system, 250A continuous and 750A momentary at DC 12V.. Application Easy to UseRecommended to mount on NEGATIVE battery post, Widely used for Car, Vehicle, RV, ATV and Boat batteries, also used for electrical equipment. Vertical knife blade type, easy to install simple to use.. FunctionThis Switch Battery Disconnect Switch Isolator is Used for battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.. 100 satisfaction guaranteeIf you have any issues with our Side Post Battery Cut Off Shut Off Switch, simply contact customer service for troubleshooting help, parts, replacement, or refund. Our aim is to make you satisfy the parts and the service we provide for you..

Specifications Battery disconnect switch rated current 240A, rated voltage 12V, standby power consumption 3mA, power-off threshold 11.8V0.2V, instantaneous current 500A.. Automatic Cut Off Battery If the voltage is lower than 11.8V, the remote kill switch will automatically cut off the power supply after 120s to save electricity, if the voltage is higher than 13.2V, the remote control will be disabled to prevent accidental action to shut off the power while driving, and the power supply can only be controlled by the button on the switch.. Magnetic Latching Function This kill switch for car uses a new type of relay that controls circuit disconnection and cut-off by magnetic principle, with a standby current of 3mA, which is more energy-saving.. Protecting Automotive Battery Using this car battery automatic kill switch can avoid power consumption due to long-term parking, good point of electronic equipment, line aging, forgetting to turn off the light, etc. It can effectively protect and prolong the life of car battery.. Widely Applications This automatic kill switch suit for most 12V car, boat, Rv, trailer, trucks, ATV, UTV, motorcycle, vehicles with displacement less than 4.0 Negative pole 9-13 mm and 15-17mm, not fit for small pile head vehicles..

Note On some models of vehicles, after the remote control of this product is used to disconnect the vehicle battery and turn it on again, you need to wait about 6s before pressing the vehicle start switch to start the vehicle.. For facilitate installation, the black negative wire has been installed at the bottom of the battery switch. This product needs to be connected to the original negative wire on the car. If you mind this change, we recommend that you can choose the 250A Upgrade model. Please pay attention to the installation instructions If your car stereo can not be completely power off, then once you use our product to completely disconnect the battery, the stereo needs to be re-matched when you start the vehicle again. REPLACEMENT REMOTE BATTERY DISCONNECT SWITCH - Wireless kill switch enables you to kill your car battery power with remote control, which can help to prevent battery drain and protect the circuit. Besides, car battery disconnect switch can disconnect the power of your car, the theif cannot start and stole your car. Just press the remote control button to disconnect your car power system, easy to use and improve security. WIDE APPLICATIONS - Remote battery disconnect switch works well for Car, Truck, RV, Travel Trailer, Camper, SUV, ATV, UTV, Marine, Van, Boat, Agricultural Vehicle Trike Auto Off Road Jeep and other engine applications with a 12 volt battery.. PREMIUM QUALITY - Kill Switch for Car is made of silver contact and pure copper wires. Durable and Reliable. Rated current 200A DC12V, this Battery Disconnect Isolator is upgraded from the old model as the improved fittings make mounting contacts stronger. All required wiring harnesses included, no need to buy additional accessories.. EASY INSTALLATION - No modifications needed Step 1 Connect the red wire to the positive pole of the battery. Step 2 Fix the battery clip to the negative pole of the battery. 12V battery disconnect switch allows you not to open the hood every time for turn on the power, just press the remote control key button to disconnect your car power system, saving you plenty of time.. BUY WITH CONFIDENCE - FEITON Upgraded Remote Battery Disconnect Switch comes with 1-Year Warranty, if you have any questions when using this dual remote control 12V 200A car wireless remote battery disconnect switch isolator On Off kill master, please feel free to contact us for a replacement. We will reply your email as soon as possible.

With Silver Contact SurfaceCurrent Amperage is Larger and More Durable,Rated Current 300A Main Switch Silver Contact SurfaceCompared to copper contacts, it has a higher melting point, higher hardness, and oxidation resistance, avoiding the gradual melting and deformation of the product due to high temperature when the contacts come into contact.. Remote OperationCompared with traditional battery switches, this remote control electromagnetic battery switch is equipped with silver pin control, which can be up to 328 feet away.. Convenience and anti-theft The remote isolation switch is more convenient than other switches. You can turn off the battery without opening the hood. Simply press the unlock button to prevent the battery from malfunctioning when not in use and prevent thieves from starting your car. This can prevent the battery from running out and keep it fully charged.. Widely usedthis Remote Control Electromagnetic Battery Switch Disconnect for automotive, truck, RV, travel trailer, camping vehicle, boat, agricultural vehicle Auto off-road jeep,mechanical equipment, excavators, loaders, etc. and other engine applications with 12 volt batteries.. Package Includes1 x Electromagnetic Car Battery Switch, 2 x Remote Control, 1 x Manual.. NOTEUniversal for DC 12V Power System.Idea for different vehicle - 12V relay match 12V Electromagnetic ,24V relay match 24V Electromagnetic..

Heavy Duty all aluminium housing, durable made for safety use. Mounts in 34 hole, equiped with a face plate.. Operation OnOff 2 positions, 200 A continuous at DC 12V, 400 A momentary at DC 12V.. Compatible used for DC 12 - 24 V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.. Purpose eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.. Copper terminal stud size 38 10 mm x 2, very easy to install, universal used for car, vehicle, Rv and boat, also electrical equipment's switch..

SpecificationsBattery disconnect switch rated current 240A, rated voltage 12V, standby power consumption 3mA, power-off threshold 11.8V0.2V, instantaneous current 500A.. Magnetic Latching FunctionThis kill switch for car uses a new type of relay that controls circuit disconnection and cut-off by magnetic principle, with a standby current of 3mA, which is more energy-saving.. Automatic Cut OffIf the voltage is lower than 11.8V, the remote kill switch will automatically cut off the power supply after 120s to save electricity, if the voltage is higher than 13.2V, the remote control will be disabled to prevent accidental action to shut off the power while driving, and the power supply can only be controlled by the button on the switch.. Easy InstallationThe power shut off switch uses a negative connection to ensure stable performance. Please remember to turn off the power before installation.. Protect the BatteryUsing this car battery kill switch can avoid power consumption due to long-term parking, good point of electronic equipment, line aging, forgetting to turn off the light, etc. It can effectively protect and prolong the life of car battery..

SpecificationsBattery disconnect switch rated current 240A, rated voltage 12V, standby current 3mA, instantaneous current 500A.. Magnetic Latching FunctionThis kill switch for car uses a new type of relay that controls circuit disconnection by magnetic principle, with a standby current of 3mA, which is more energy-saving.. Intelligent Led Voltage DisplayThe LED voltage display detects the battery voltage at any time, if the voltage is lower than 11.8V, the remote kill switch will automatically cut off the power supply after 120s to save electricity. If the voltage is higher than 13.2V, the remote control will be disabled to prevent accidental action to turn off the power while driving, and the power supply can only be controlled by the button on the switch.. Easy InstallationThe power shut off switch uses a negative connection to ensure stable performance. Please remember to turn off the power before installation.. Protect the BatteryUsing this wireless car battery kill switch can avoid hidden additional power consumption due to long-term parking, aging of electronic equipment, line aging, forgetting to turn off the light, etc. It can effectively protect and prolong the life of car battery..

PURPOSRBy cutting off the battery with a master battery disconnect switch removes all parasitic loads and small leakage currents, Works Great As a Power Disconnect for RV's When Not in Use.. PREMIUM QUALITYMade of robust aluminum alloy heavy duty housing, strong weather resistance and long service lifespan. Protects against parasitic battery drain.. EASY TO INSTALLThis battery isolator switch with face plate is easy to install. The panel faceplate is clearly labeled with off and on positions. And they also included 38 brass studs with nuts and locking washers to ensure that the switch is snugly secured to your power panel.. COMPATIBLEThis high current battery disconnect switch is used for DC 12 - 24 V systems to isolate and secure the electrical system, rated to 300A Continuous or 1000A Intermittent.This makes sure that the item will not fail even when the system experiences an electrical surge.. WIDE APPLICATIONWidely used for ATVs, Trailers, UTVs, Cars, Marine Outboard, Off-road, RVs, Trucks, Heavy Vehicles, and electrical equipment's switch..

Heavy Duty ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equiped with 4 sets of bolts.. Operation OnOff 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.. Compatible used for DC 12 - 48 V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.. Purpose eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.. Copper terminal stud size 38 10 mm x 2, very easy to install, universal used for car, vehicle, Rv and boat, also electrical equipment's switch..

UNIVERSAL BATTERY DISCONNECT SWITCH - High current battery disconnect switch is designed to cut off the electrical power of the electrical system, which protects against electrical fires and theft when equipment is not in use and provides a reliable way to shutdown electrical power during maintenance and protect batteries from excessive battery drain. Disconnct the battery when you are not driving a car boat RV vehicle ATV Trailers Off-road, etc. Keep you safe all the time.. APPLICATIONS - Rated to 300 Amps continuous duty, 1000 Amps intermittent duty, used for 12-48 VDC systems to isolate and secure the electrical system. Master battery disconnect switch is widely used for ATVs, Trailers, UTVs, Cars, Marine Outboard, Off-road, RVs, Trucks, Heavy Vehicles, and electrical equipment's switch.. PREMIUM QUALITY - Master battery disconnect switch with face plate is made of robust aluminum alloy heavy duty housing, strong weather resistance and long service lifespan. It can protect the internal components of the switch for use in the harsh condition. Replace part number 20701, 062790.. EASY TO INSTALL - 12V Battery isolator switch comes with onoff indicator, it includes a definitive click when turning on and off. No modifications required HOW TO INSTALL Step 1 Disconnect the battery and choose the negative cable Step 2 Choose the proper mounting position for the switch Step 3 Connect the positive and negative cables DO NOT ATTACH AT THE SAME TIME to shut off the switch , then install the switch Step 4 Reconnect the battery and check for correct operation.. BUY WITH CONFIDENCE - This battery disconnect switch comes complete with a 1-Year warranty. If the shut-off switch ever fails on your ATVs, Trailers, Off-road, RVs, Trucks, Heavy Vehicle, UTV, Boats, Cars Rated to 300 Amps continuous duty, 1000 Amps intermittent duty, used for 12-48 VDC systems. during this period, please feel free to contact us for a replacement. Save time and money by purchasing this part, replacing them by yourself within minutes..

Simple OperationSwitch on Power Switch off No power.Rating 275A DC Continuous 1hr, 455A DC Intermittent 5 min, 1250A DC Cranking 10 sec Stud Size 2x38 10mm. Durable Material This battery disconnect switch is made of ABS plastic housing, tinned copper studs and nuts.Come with 4 stainless steel mounting screws and caps to help fix the switch tightly. 4 Removable side plates provide access for battery cables. Safety Protectionbattery shut off switch can disconnects the battery safely, protect batteries from excessive drain when vehicle or boat is not in use. Great CompatibilityThis battery quick disconnect is used for DC 12 - 48V systems to isolate and secure the electrical system,and can stand alone or be locked together with other switch, simple and economical way to separate batteries.. Wide Applicationuniversal used not only for Car, Van, Caravan, RV, Truck, Marine Boat, but also electrical equipment's switch, such as flashing light, chassis light, fog light, dome light..

Heavy Duty ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits, equipped with 4 sets of bolts.. Operation OnOff 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.. Compatible used for DC 12 - 48V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.Its purpose is to eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.. Widely used for car, marine boat, RV, camper, travel trailer, truck, ATV, UTV, battery banks and other devices.. Package include1x OnOff battery switch,4 bolts incuded..

Must Have Battery Disconnect Switch Battery disconnect switch protects everything from cars to boats to semis with this knob, handling 12V of up to 125A continuous 500A momentary current. It is ideal for cars, boats, trucks, RVs vehicle and electrical equipment batteries.. Safety Protection Battery cut off switch 12v is designed to cut-off power flowing of the vehicles battery to avoid unauthorized use of your vehicle or unwanted battery consumption when not used, prevent vehicles from battery drain and reduces the risk of electrical fire. Easy Use Spurtar battery kill switch is convenient to use. Simply to engage power by hand tighten the green knob and slightly loosen the green knob to disconnect all power. Make sure the negative battery post and battery clamp original battery connector clean before install. Wide Application Spurtar battery disconnect switch is suitable for most top post terminal 15-17 mm cone battery negative post. Please make sure this battery terminals top post kill switch for car use under the condition of 12V voltage, 125 A, knob type. Premium Quality Battery disconnect switch 12v battery isolator made of heavy duty solid brass, rust and corrosion resistant, greatly protect the battery disconnect isolator from rust and corrosion, durable for long term safety use.

INSTALLATION AND USE Install the Battery Disconnect Switch on the negative cable, toggle the lever up or down to turn the power off or on, make sure the connection is good, onoff 2 positions.. HIGH COMPATIBILITY 12V 24V Vertical Top Post Knife Blade Switch Continuous 250A and Momentary 750A is easy to install, compact, flexible and convenient to use. Widely used in Car, Boat, RV and ATV.. QUALITY MATERIAL Battery Cut Off Shut Off Switch made of pure copper, good conductivity, rust and corrosion resistant.. FUNCTIONAL USE Not commonly used cars parked for a long time will consume battery power, battery disconnect switch for battery isolation and protection of the electrical system, prevent the battery from running out of power, prolonging the service life of the battery.. GOOD CHOICE The battery cut off switch is smooth and shiny, not easy to hurt your hand, protect the battery, it is a must-have good thing for family. We always take your satisfaction as the ultimate goal..

Remote Battery Disconnect Switch Function Long term parking, electronic device power consumption, line aging, forgetting to turn off the lights, which will cause battery to run out and vehicle cannot start normally, installing our kill switch can maximize the storage of car battery power, effectively protecting and extending lifespan. Remote control distance 30-70M, rated voltage 12V, rated current 500A, instantaneous current 2400A, battery disconnect switch is suitable for cars, boats, campers, RVs, ships, travel trailers, beaches with displacement less than 4.0 Cars, motorcycles, etc. Smart Voltage Kill Switch battery kill switch detects the voltage at all times. In smart mode, when the battery voltage is lower than 11.9V, the switch will automatically turn off after 5 minutes, when the battery voltage is higher than 13.3Vfor example, driving, remote will not control the switch. The standby current of this car kill switch anti theft is only 0.005A, which is far lower than the standby current of the original car, which is more than 65 mA. It will not drain your battery. The car battery switch is made of pure copper. Durable and reliable. The battery disconnect isolator is upgraded from the old model, because the improved accessories make the installation contact more secure..

Anti-Theft Security Equipped with a remote control, this switch provides a powerful anti-theft feature by allowing you to remotely disconnect the battery, preventing unauthorized vehicle use.. Battery Leakage Protection Features a leakage indicator that actively monitors and signals any battery drain when the vehicle is off, ensuring your batterys longevity and reliability.. Durable Design Built from thick pure copper and equipped with a magnetic latching relay, the switch is designed for durability and long-lasting performance.. Easy Installation Simple to install with a clear, five-step process, making it accessible for most vehicle owners.. Wide Vehicle Compatibility Suitable for a variety of vehicles including cars, boats, and RVs, particularly those with engine displacements under 4.0 liters..

Ideal Power Switch - With tinned copper inner studs, the boat battery switch has better contact performance and good conductivity, greatly reducing power consumption. Studs Size 2 x 38 10mm. Furthermore, the housing of battery kill switch is made of flame-retardant plastic for safer use in messy or moist environment.. 2 Position Ignition Protected - This battery shut off switch is single circuit ONOFF design, simply turning the knob to ON or OFF position to realize the control of the power circuit. Of course this car battery switch has ignition protection as its crank rating that withstands 900A for 30 seconds, 500A for 5 minutes, and 300A continuously.. Easy to Install - The battery disconnect switch is euipped with mounting screws for easy installation which could save your time and money on extra accessories. The 12V switch shell is easily disassembled, and the space inside the shell is large to complete the wiring tasks. Moreover, the switch base has partition design to reduce interference between wires.. Safe and Practical - This battery cut off switch is suitable for 12-48V DC systems, often used for the control and protection of electrical systems. When the battery is not in use for a long time, this car battery switch can safely disconnected the power supply so that can prevent leakage and reduce energy consumption.. Wide Compatibility - The marine battery switch is usually used with the battery box, fuse block which can isolate and protect the electrical system. This battery switch is widely applied to marine, boat, yacht, car, RV, camper, travel trailer, truck, ATV, UTV, etc. When your RV, boat or car is not in use, the power switch can safely disconnect the battery power, reducing the additional loss of battery power and extending the battery life.

Save Your Battery The Spartan Power OnOff Battery Switch prevents any current from being drawn from the battery when your RV, van, boat, or car is not in use Disconnect your battery safely and extend its life. Ignition Protected Our switch has a crank rating that withstands 900A for 30 seconds, 500A for 5 minutes, and 300A continuously, protecting against fluctuations in current during ignition. Simple, 2 Position Design Our simple design is easy to read and to operate, simply turn the knob to either the On or Off position, and a satisfying click will let you know it's changed. Screws Included The casing design allows for front or rear panel mounting, and we are now including screws to facilitate installation on your DC system. Giving Power to The People Helping people arm themselves with the right tools and accessories, Spartan Power manufactures ultra-high quality, durable, and heavy duty products Trusted by professionals, enthusiasts, and DIYers everywhere.

High Current Battery Switch With a rated current of 200 Amp Continuous, and 1000A Intermittent, Spurtar battery disconnect switch safely isolate and secures 12-48V DC electrical system connections. Safety Protection Spurtar battery switch provides power cut-off to the electrical system, prevents your vehicle from battery drain, and reduces the risk of an electrical fire. When your car, boat, or RV is not in use, disconnect the battery for the safety of your vehicle and property. Easy Operation The battery shut-off switch is toggled smoothly with a clear click sound, without jamming. Spurtar battery cut-off switch with on off indicated face plate is easy to install, and can be for professional installation. Wide Application The RV battery disconnect switch is widely used for heavy vehicles, boats, RVs, campers, trailers, off-road, ATVs, trucks, tractors, forklifts, motors, electric winches, and other electrical equipment. Battery Kill Switch Kit You will get 1x 200 amp disconnect switch, 2x 38 Copper Lugs, 2x Heat Shrinks, 2x Rubber Terminal Insulator Sleeves to prevent incidental shorting and improve the appearance of your wiring. Important Notice Before purchasing please compare the Spurtar heavy-duty switch dimensions with your application requirements. Ensure your mounting location can accommodate the dimensions to avoid fitting issues..

100M REMOTE CONTROL BATTERY DISCONNECT SWITCH. 100M remote battery kill switch used for 12V equipment that not in use, prevent battery from parasitic drain or as a theft deterrent. Convenient FOB remote control, no need to open the hood to disconnect battery, just a quick button push. The remote is preprogrammed and ready to go out of the box. HEAVY DUTY HIGH CURRENT DEVICE. High current rated to 200A Continuous 1000A Crank Amps. Enough crank amps to start your car in cold weather. This is a high quality solid state relay with a remote control receiver circuit built into it. This switch lasts 3-4 times longer than an ordinary relay switch. ZOZOMOTORS uses high quality durable parts only. The current draw of this switch the remote receiver is 0.001 - 0.005 AMPS while connected. it's very minor. VOLTAGE 12V, FLEXIBLE CONNECTION WIRE PROVIDED FOR EASY INSTALL EVEN IN TIGHT SPACE. You can use the provided 2AWG connection wire or copper bars to easily connect the switch to your battery 38 diameter hole with bolts. Recommend install on the NEGATIVE SIDE of the battery. Installation on the positive side is also allowed. This switch can be used to disconnect 12V system including cars, trucks, RVs, boats, and other equipment. EASY TO INSTALL, WIRING DIAGRAM IS PROVIDED. Package includes Installation Instructions with Wiring Diagram, Relay Switch with Wire Harness, 1 Remote Switch, 1 Connection Wire 2AWG, 2 Connection Copper Bars, 3 Bolts 38-16 Thread, 2 Relay Mount Screws. The red and black wires power the remote receiver in the relay and should always go to the positive and negative battery poles respectively. One side stud terminal of the relay goes to the negative pole on the battery, and the other gets the negative wire from the car. REMINDER. This switch is to disconnect power directly from the battery, electronics that store data, like your radio, will lose memory. California users must keep the battery connected without activating the switch for several days before a smog test.

Wide ApplicationThe battery isolation switch is suitable for automobiles, vans, RVs, trucks, ships, campers, travel trailers, battery boxes, ATVs, UTVs, or any vehicle that requires a battery disconnect switch.. Compatibility Benefits Used in DC 12-48V systems, for isolating and fixing electrical systems When the vehicle is not in use, eliminate any power consumption from the battery and safely disconnect the battery Provides a reliable method to turn off the power supply during maintenance and protect the battery from excessive consumption.. Heavy Duty ConstructionDurable and sturdy ABS shell, with a back cover that insulates the terminals to prevent any short circuits 4 detachable side panels, capable of connecting up to 10 cables Tinned copper studs and nuts with strong oxidation and corrosion resistance. Simple OperationTwo positions onoff 0off, 1on, continuous 275A at 12V DC, intermittent 455A at 12V DC, and instantaneous 1250 A at 12V DC Voltage 12V-48V DC Terminal size 2x38 10mm. Warranty ServiceIf you encounter any problems while using this product, we will solve it for you as soon as possible. A 6-month warranty for refunds or replacement of any defective products.

EXTEND THE LIFE OF YOUR BATTERY The battery kill switch helps to disconnect battery easily to prevent it from draining down when not in use. EASY TO INSTALL It only takes 5 steps to install. 1, Make sure the negative battery post and battery clamp original battery connector clean before installation. 2, Tighten the green knob. 3, Remove the negative cable from battery. 4, Install the disconnect switch on the battery post. 5, Install the cable on the stud end of the disconnect switch. EASY TO SWITCH ON AND OFF Disconnect or connect battery by twisting the green knob a few turns. And also you can take the knob off to prevent vehicle theft. Much easier than taking the battery cable off each time. DURABLEHIGH QUALITY The battery cut off switch is made of zinc alloy with brass plating, corrosion resistance. Widely used for car, boat, truck, RV vehicles and electrical equipment. REST ASSURED TO PURCHASE We offer 30-day money-back for any reason, 12-month warranty for quality-related issues. Any problem in using our battery disconnect switch, please kindly contact us, your problem will be solved within 24 HOURS.

Rotary Switch. Panel Mount. 125 amp 12V. Aluminum On Off Panel. Fit type Vehicle Specific.

Compatible- The battery disconnect switch is used for top post terminal0.59''- 0.67'' cone battery negative post only. Compatible the condition of 12V voltage, 125A rated current, heavy duty.. High Quality- Our solid brass 12v battery disconnect switch with stainless steel fasteners provide excellent oxidation resistance and corrosion resistance, no need to worry about its service life.. Easy to UseKnob type design to disconnect or connect battery, just follow the direction instructions on the switch, unscrewing or tightening the battery switch into an on or off position to control current.. Protect BatteryThis battery shut off switch is designed to cut-off power flowing to the battery, avoid unwanted battery consumption when not used for long periods of time, extend the life of battery.. Widely Applications- Suitable for Car, Marine,tractor, camper, boat, RV, truck batteries which have a standard 0.59''-0.67''15-17 mm cone top post terminal, also used for electrical equipment..