COMPACT DESIGN Supports installation in tight spaces helps fit the unit into limited mounting areas. EMERGENCY COMBINE Provides a combine feature to draw power from both batteries during engine starting or essential radio use supports power availability when one battery is low. MOUNTING OPTIONS Offers three mounting methods for flexible installation can be placed on the surface, flush, or at the rear of the panel. CONTACT DESIGN Make before break contact design supports switching between battery banks without power interruption helps maintain continuity during transitions. IGNITION PROTECTION Includes ignition protection suitable for installation in the engine room of gasoline powered boats supports placement in locations requiring protected components.

Disconnect switch for GM side post battery, MarineRV battery, M8 AGM battery and other equipment - This battery switch can be used for any 12V-48V systems that not in use, prevent battery from parasitic drain or as a theft deterrent. Just flip the switch and no worry of any amprage draw with this mechanical battery switch. Also used as a cut off switch between batteries and accessories. Patented design, Compact size - The Height of this battery switch is only 1-12 inches. Designed for limited space install in the engine bay. Recommend install on the NEGATIVE side of the battery, can be installed on the positive if needed. Please check clearance requirements before purchase. High current device, Waterproof, Marine grade terminals - 300A Continuous 900A Crank Amps. 48V DC Max. Heavy duty tin-plated copper terminals for maximum conductivity and corrosion resistance. This battery disconnect switch is used to shut off the power when your vehicle or boat sits for a while. Quick disconnect switch for car, truck, RV, marine, boat, golf cart, jet ski and other equipment. Removable knob, Robust built to last - The knob is removable to prevent unauthorized action. Easy-to-turn large red knob. PA66 housing for safety use in the engine department Temp rating -40 to 284. Solid manual cut off switch with mounting hardwares - Package includes 1x Install Guide, 1x Disconnect Switch 38 hole terminals, 2x 516-18 Bolts, 2x 38-16 Bolts. Please note this switch is to power off the whole system by the battery, electronics that store data like your radio, will lose memory every time you switch off.

Blue Sea Systems Battery Switch m-Series Selector, Black, part number 6007200, is a Selector 4 Position switch. Switches isolated battery banks to all loads or combines battery banks to all loads. IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protectedsafe for installation aboard gasoline powered boats. Make before break contact design allows switching between battery banks without power interruption. Continuous Rating 300A, Maximum Voltage 32V DC.

SAE top post battery, Negative disconnect - This battery switch can be used for any 12V-48V systems that not in use, prevent battery from parasitic drain or as a theft deterrent. No need to manually disconnect the cable from battery every time. Patented design, Compact size - The Height of this battery switch is only 1-12 inches. Designed for limited hood clearance install. It can be installed directly on top of most batteries. Flexible installation for tight space, refer to image 6. Please check clearance requirements before purchase. High current device, Waterproof - 300A continuous 900A crank amps. 48V DC Max. IP66 waterproof. Heavy duty copper terminals for premium conductivity. This battery disconnect switch is used to shut off the power when your vehicle or boat sits for a while. Quick disconnect switch for car, truck, RV, marine, boat, and other equipment. Removable knob, Robust built to last - The knob is removable as an anti-theft feature or to prevent unauthorized action. Easy-to-turn large red knob. PA66 housing for safety use in the engine department Temp rating -40 to 284. Solid mechanical switch, Package includes 1x Install Guide, 1x Disconnect Switch, 1x SAE Female Battery Clamp Negative, 1x SAE Male Terminal Post Negative, 1x Adjustable Spacer. Please note this switch is to power off the whole system by the battery, electronics that store data like your radio, will lose memory every time you switch off.

Type Heavy Duty Dual Battery Switch Battery 1, Battery 2, Both, or Off positions. Isolates 1 battery or 2 batteries, or links up both batteries in parallel Suitable for use with two or more batteries and single or dual engine systems 6-32Vunder 50V. They permit selection between batteries for starting and charging or operation of both batteries in parallel.. Capacity Rated for 250A continuous,360A intermittent, at up to 32 volts.. MaterialPlastic Copper. Made of high-impact plastic with copper-plated cable lugs for durability Copper washers and solid brass stands up to tough marine conditions..

Easy Installation The side post design and removable bolts make the installation process more straightforward, eliminating the need for additional battery cables or connectors direct connection to the battery is sufficient. High Flexibility The removable bolts allow for easier maintenance and replacement of the switch, enabling users to adapt to different environments. Enhanced Connection Stability The design ensures a secure connection to the battery, reducing the risk of poor electrical contact and improving system stability. Versatile Application This design enables the switch to be used in various scenarios, such as boats, RVs, and campers, providing reliable power management and isolation solutions. Durability The combination of side posts and removable bolts enhances the overall strength and durability of the switch, ensuring stable operation even in harsh environments.

Streamlined Switch Design The 1-Both-2-Off knob switch is a 4-position selector switch. It allows for switching isolated battery banks to all loads or combining battery banks to all loads. Comes with 4 screws.. Uninterrupted Power Switching The make-before-break contact design allows for switching between battery banks without interrupting the power supply.. Superior Quality Constructed with high-quality ABS plastic for the housing and tinned copper studs, this design prevents battery switch leakage, protects the power supply, and safely disconnects the battery.. Spark-Proof Design Featuring an ignition-proof design, it can be safely installed on gasoline-powered boats. The chassis design supports surface, front panel, or rear panel mounting. Suitable for yachts, RVs, off-road vehicles, modified vehicles, and ATV UTVs.. Safety Protection With a continuous rating of 300A45 higher than standard switches, and a maximum voltage of 48V DC, it eliminates any power draw from the battery when vehicles or boats are not in use, ensuring a safe disconnection..

VERSATILE 4-POSITION CONTROL This battery selector switch 4-position 1-Both-2-Off offers complete power management. Easily switch between Battery 1, Battery 2, combine both BOTH for extra power, or shut everything off OFF to prevent battery drain. Perfect as a boat marine battery switch, battery cut off switch, or kill switch for car, truck, RV accessories. UNINTERRUPTED SAFE POWER SWITCHING The make-before-break design allows you to change settings without dropping power to critical devices. In the OFF position, it acts as a total battery cut off switch, eliminating parasitic drain to save your battery. This dc switch is ideal for use as a battery shut off during storage or maintenance. EASY INSTALLATION UNIVERSAL FIT This 12v battery switch is designed for easy setup with multiple mounting options surface, front, or rear panel. The 38-16 terminals easily accept up to 20 AWG cables for your RV battery kill switch or car's electrical system. The battery disconnect switch is equipped with mounting screws and for easy installation. HEAVY-DUTY DURABLE CONSTRUCTION Built to last with a high-quality ABS plastic housing and corrosion-resistant tinned copper studs. Achieves an IP68 waterproof rating, meeting ISO 8846 standards for marine use. It's the ultimate safe battery shut-off switch for boat accessories and vehicles, ensuring no sparks and all-weather reliability. ULTIMATE BATTERY ISOLATOR With a continuous rating of 300A and a maximum voltage of 48V DC, this heavy-duty cutoff switch outperforms standard automotive replacement battery switches. Functioning as a reliable battery cut-off switch, it completely eliminates parasitic power draw when your vehicle or vessel is stored. This ensures your batteries are always charged and ready, enhancing safety and longevity.

Reliably controls the battery charging and power draw on boats with two or more batteries. Use it to select which battery is providing a power draw for starting, general operation, and charging. Dependable switch also allows operation or charging of both batteries in parallel. Lets you select Battery 1 or Battery 2, or all available batteries for power draw and charging. Durable switch is designed for use with systems under 50V - 315A continuous and 450A intermittent. Red plastic housing measures 4 inches x 4 inches x 3 18 inches side panels are removable for easy wiring. Made in the USA. Manufacturer part number 50-11531.

Continuous rating 350A, Max volt 32V DC. High quality ABS and copper material can make sure the durability and stability of the product. With ignition protection function, can be safely installed on gasolinepowered boats. The terminal size is 38in-16, the standard specification make it convenient to connect. IP66 waterproof, ISO 8846 requirements,can accept 2 40 AWG 95mm battery cables, easy to connect.

Fast DC Failover Switching When the primary power fails, it rapidly switches to the backup power in just 0.007 seconds to minimize downtime and ensure continuous operation of critical equipment. This is not a seamless switch - a brief power interruption may occur during transition.. Comprehensive Protection Built-in reverse polarity protection and overload protection prevent damage from incorrect wiring or power surges. Safeguards your devices and power sources.. Auto External Trigger Select Automatic Control Mode A for automatic switching, or Input Control Mode B for manualexternal signal control.. Status Indication Clear LED indicators provide instant visual confirmation of the active power source primary or backup for easy monitoring.. Wide Applications Designed for DC 560V, 5A continuous 8A peak. Works seamlessly with solar panels, batteries, and Starlink Mini DC setups with proper DC-DC conversion..

MATERIAL RV Battery Disconnect Switch 12V made of ABS plastic housing, and the 4 sets of bolts are tinned copper studs2 x 38 10mm nuts for ignition protected to distinguish the different gears easily which you switch to even at night.. EASY OPERATION The Marine Battery Switch with OnOff position in clear color labels. Switch ONPower green to the closed circuit, Switch OFF No power red to the cut-off circuit.. COMPATIBLE Used for 12-48V, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V, battery selector 12V switch can stand alone or be locked together with other switches for minimizing battery loss and preventing electric leakage effectively.. SAFE PROTECTIVE The Battery Isolator Switch comes with CE Certification, and 4 removable side plates, the rear cover insulates terminals against any short circuit.. WIDE APPLICATION Kohree Battery Cut Off Switch 12V serves as a power cut-off when a vehicle or boat is not in use on RV, ATV, car, marine boat, camper, camper, travel trailer, truck, UTV, etc..

1-2-BOTH-OFF CONTROL HIGH CURRENT RATING Take full command of your dual battery setup. Easily switch between Battery 1, Battery 2, both batteries combined, or completely OFF. Perfect for isolating batteries to prevent drain during storage on your Boat or RV, or combining power for engine starting. Handles 200A continuous, 300A for 5 mins, and 1000A surge currents.. SUPERIOR CONDUCTIVITY DURABILITY Ensures minimal voltage drop and maximum reliability even under high loads. The premium tin-plated pure copper terminals and internal components offer excellent conductivity, reduce heat buildup, and resist corrosion in harsh marine or automotive environments.. IP54 WATERPROOF DUSTPROOF HOUSINGProtects the switch from water spray, moisture, and dust, ensuring dependable operation rain or shine.Ideal for exposed installation locations in marine applications boats, yachts or under the hood of off-road vehicles and RVs.. WIDE COMPATIBILITY EASY INSTALLATION A versatile solution for numerous 12V, 24V, and 48V DC systems. Works seamlessly for Cars, Trucks, Motorhomes, Campers, Travel Trailers, Boats, Yachts, ATVs, and UTVs. Includes 4x M8 8mm mounting bolts for straightforward panel mounting 68x68mm cutout.. SAFETY RELIABILITY FOCUS Safeguard your electrical system and batteries.This master battery disconnect switch allows for safe maintenance by cutting all power, helps manage battery usage to avoid being stranded, and features an insulated rear cover to prevent accidental short circuits..

High QualityA ABIGAIL Top Post Knife Blade Master Switch is made of Heavy Duty solid brass which is rust and corrosion resistant, durable made for safety use. Note Please Do Not choose the Material of brass plated with copper. OperationThis knife blade master switch is OnOff 2 position, Battery negative pole 15.5mm-17mm, DC 12V-24V system, 250A continuous and 750A momentary at DC 12V.. Application Easy to UseBattery NEGATIVE post only, Widely used for Car, Vehicle, RV, ATV and Boat batteries, also used for electrical equipment. Vertical knife blade type, easy to install simple to use.. Function This knife-blade battery disconnect switch is used for battery to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.. 100 satisfaction guaranteeIf you have any issues with our Battery Cut Off Shut Off Switch, simply contact customer service for troubleshooting help, parts, replacement, or refund. Our aim is to make you satisfy the parts and the service we provide for you..

Prevent Battery Drain 12-48v battery switch is provide a convenient to disconnect the batteries from the electrical system, which refrains battery from draining during storage and isolate power in case of emergencies Avert accidental discharge, electrical fires, helping you get the most out of your battery. Specification RED WOLF 1-2-Both-Off boat battery cut off switch 12V-48V features OnOff 4 Position Rating 200A DC Continuous, 300A DC Intermittent, 1000A DC Cranking Stud Size 3 x 516 8mm Power busbar is able to reach 250A MAX when inputoutput voltage between 12V-48V DC, NOTE MAX Continuous Current will DECREASE with Temperature Humidity Effection. 1-2-Both-Off Functionality Control over which batteries are connected to auto boat's electrical system Whether you need to isolate a single battery for maintenance or balance the load between multiple batteries for optimal performance, this switch offers unparalleled flexibility. Solid Durable Quality Power Disconnect wABS plastic housing rear cover insulates terminals against any short of circuits 3 x 516- M8 tinned copper studs and nuts, which is safer and more reliable in electrical conductivity Flame retardant rating 94VL. Widely Application Battery isolate switch is usually used with the battery box, fuse block which can isolate and protect the electrical system widely applied to marine, boat, yacht, car, RV, camper, travel trailer, truck, ATV, UTV, etc. Easy installation Straightforward and easy to operate RED WOLF battery switch is designed for surface, front panel, or rear panel installation, and you can choose any one according to your needs Clockwise to turn on , counter clockwise to turn off.

Heavy Duty ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits. Design for 2 batteries vehicles, can switch battery 1 battery 2 separately or both on and off.. Purpose eliminate any power from the battery when vehicle or boat is not in use, disconnects the battery safely.Avoid battery drain off.. Operation 1-2-Both-Off,4 positions, 600A continuous at 12VDC, 455A intermittent at 12VDC, 1250A momentary at 12VDC.. Compatible used for 12 - 48VDC systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.Widely used for cars, marine boats, RVs, campers, travel trailers, trucks, ATVs, UTVs, battery banks and other devices.. Package include1x battery switch, 4 bolts,3x Copper Ring Terminals,4x Heat Shrink Tubings , 1x hex wrench..

Premium Quality,Durablehe white cover can be removed. Made of premium ABS and metal material, 12-32V battery disconnect switch is sturdy, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage.. Waterproof Protective CoverThis waterproof power disconnect cut off switch is designed with a waterproof cover on the top can better protect the key hole. Professional characteristics, high reliability. Compact size, sleek modern appearance, easy to install and Cable connection.. Disconnect Battery SafelyThis battery isolator switch can eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely. 2-Position ON and OFF positions. Battery Disconnect Shut Off SwitchThey are offered as main car kill disconnect switches, Continuous Rating 200Amps 32VDC Max. Intermittent Rating 300Amps Cranking Rating 1000 Amps 5 sec. Contact Resistance 50m ohm Max Insulation Resistance DC 500V 100M ohm Min Dielectric Strength AC 1000V 1 minute, DC 2000V 1 minute Operation Temperature 30 60 Switch Function 2P SPST OFF-ON Mounting Hole 38mm. Wide ApplicationQuality GuaranteeThe waterproof battery isolator Selector switch is perfect suitable for cars, off road vehicle, truck, motorcycle, boat, etc.Professional characteristics, high reliability, 100 test before shipping to ensure product perfect, stability and durability.If you are not satisfied with our Battery Isolator Switch,We accept all of the return, replacement or refund requests.

AUTOMATIC CHARGING RELAY Includes Automatic Charging Relay that senses charge voltage combines batteries during charging and isolates at rest. DUAL CIRCUIT PLUS SWITCH Manages starter and house banks independently maintains power distribution while protecting reserve capacity. EMERGENCY PARALLEL FUNCTION Integrated combine feature links batteries when needed supports engine starting if one battery is discharged. SIMPLIFIED TWO BANK CONTROL Single ON and OFF operation controls two battery banks reduces switching errors and wiring complexity. MARINE RATED COMPONENTS Tin plated copper studs resist corrosion in harsh environments continuous rating of 120 A for inboards and larger outboards.

Switch Function This battery disconnect switch is used in 32-volt DC systems to isolate and protect the electrical system for safe switching between batteries, loads and charging sources.. High-quality Material Made of ABS plastic housing and silver-plated copper studs to maximize conductivity and protect wiring from dust, corrosion and rain. Safety Our marine battery switches meet CE certification and ABYC requirements, and the one-piece terminal stud design will not loosen over time. External ignition protection allows for safe installation on gasoline-powered boats. Easy To Install Just follow the instructions to connect the power supply and the device. Wide Applications Suitable for large construction vehicles, ships, boats, yachts, campers, RVs, travel trailers, trucks, ATV, UTV, etc.

Tested to UL1107 ignition protection, CE. Tinned copper 10mm 38 studs. Stainless steel washersnuts. Fiber reinforced plastics. 400A Continuous 600A 5 minutes Intermittent 1500A 10 seconds Cranking.

Widely Application The battery switch widely used for car, marine, boat, RV, camper, travel trailer, truck, ATV, UTV, battery banks and other devices. The 300A battery switch can be installed on the circuit on the gasoline powered boat.. Premium Quality The battery disconnect switch with Isolating ABS plastic shell and red copper plated silver inner core for maximum conductivity. Safe ignition protection for installation aboard gasoline powered boats.. Main Function 3position 3stud dualcircuit battery switch, switches a single battery to a single load group. Connect first and then break contact design, allowing to switch between battery packs without interrupting the power supply.. High Performance 300A battery switch is used to isolate and secure the electrical system, eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely. Ideal for marine or RV applications.. Simple Installation Label with OFF12, rotary actuator, IP66 waterproof protection function is ideal for replacement of old or damaging. Installed in the circuit, directly installed for use. Case design allows surface, front panel, or rear panel mounting..

The safe switching between batteries, loads, and charge sources is achieved using products like the m-series battery switches.The contact design before the break point can switch between battery packs without interrupting the power supply.. Our Battery switches feature durable heavy-duty housing constructed from high-quality ABS plastic housing and Tin-plated Copper studs, providing excellent weather resistance and an extended service lifespan. With a fully enclosed design, these switches safeguard internal components from harsh conditions, preventing dirt, corrosion, and rain damage.. Battery Switch m-Series Off,1,2 with Knob.Switches isolated battery banks to all loads or combines battery banks to all loads. Make before break contact design allows switching between battery banks without power interruption. Continuous Rating 300A, Maximum Voltage 32V DC IP66 waterproof.. An innovative snap-together design increases reliability and longevity without the use of internal fasteners. The back cover is one-piece with break-out-sides, for easier installation. Every stud is pressed into a copper reinforced bus for added support..

GET NEW ONE IF NOT MAN MADE BROKEN IN 3 YEARS SINCE YOU PURCHASE THE SWITCH.. Product Name 3 Position Lacthing Selector, Ui 690V, Ith 20A 12 Terminals.. Model LW28, 3 positions1-0-2, 3 phases. Panel size 48 x 48 mm, Install Size36 x 36mm. Material Flame retardant PC material, high temperature resistance Premium copper parts with silver alloy point..

COMPACT DESIGN Supports installation in tight spaces helps fit the unit into limited mounting areas. EMERGENCY COMBINE Provides a combine feature to draw power from both batteries during engine starting or essential radio use supports power availability when one battery is low. MOUNTING OPTIONS Offers three mounting methods for flexible installation can be placed on the surface, flush, or at the rear of the panel. CONTACT DESIGN Make before break contact design supports switching between battery banks without power interruption helps maintain continuity during transitions. IGNITION PROTECTION Includes ignition protection suitable for installation in the engine room of gasoline powered boats supports placement in locations requiring protected components.

Tested to UL1107 ignition protection, CE. Tinned copper 10mm 38 studs. Stainless steel washersnuts. Fiber reinforced plastics. 400A Continuous 600A 5 minutes Intermittent 1500A 10 seconds Cranking.

Universal mount selector switch without AFD. Continuous Amps 230, Momentary Amps 345. Longer stud lengths for improved assembly and easier cable routing. Built with heavy-duty copper sweep contacts to ensure positive circuit control. Rugged internal components protected by a tough, impact resistant polycarbonate housing that is impervious to the elements. Cable Lug Size 38. Dimensions 5.0 x 2.75.

LED digital voltage displayThe battery disconnect switch features a large, bright LED digital voltage display and an intuitive onoff position. When the battery switch is turned on, it can display the current voltage status in real-time, allowing you easily monitor your battery health without needing an additional multimeter. When the battery kill switch is turned off, the screen does not display.. High Quality MaterialCrafted from high-quality nylon materials, the internal screw uses copper-plated silver silver contacts. Compared with the traditional ABS plastic shell material, our 12v battery disconnect switch with a better high-temperature resistance effect, oxidation resistance and better electrical conductivity, can withstand harsh environments and provide long-lasting performance.. Great functionality SafetyThe car battery disconnect switch suitable for DC voltage between 5-60V, making it compatible with various 6V12V24V48V60V vehicle types and battery configurations. Current 250A Continuous at DC 12V, 300A for 30 minutes. The cut-off feature allows you to completely disengage the battery, which is critical during long periods of inactivity. This not only helps in preventing battery drainage but also adds a layer of safety by reducing the risk of electrical fires.. Easy InstallationEasy to install, small arrow forward for display direction up. Comes with all necessary mounting hardware battery shut off switch, screws, nuts, removable side plate, back cover and rubber gasket for 3 different mounting methods and needs. 38 ring terminals can also be easily installed.. Wide ApplicationThis heavy duty cutoff switch is suitable for DC 5-60V system to isolate and secure the electrical system, it is widely used for RV, Marine, Car, Boat, Camper, Travel Trailer, Truck, ATV, UTV battery and other engine application. It can stand alone or be locked together with other isolator switch.. Lifetime Money Back GuaranteeWe provide a Lifetime Guarantee for this boatmarine battery switch, if you have any problem or are unsatisfied with your order, you can contact us at any time, and we will try our best to help you..

Switches isolated battery banks to all loads. Includes AFD Alternator Field Disconnect. Ignition protectedsafe for installation aboard gasoline powered boats. IP66 waterproof, ISO 8846 and meets ABYC requirements. Accepts two 40 AWG 95mm battery cables. Terminal Stud Size 12. Continuous Rating 500A, Max Voltage 32VDC.

IP66 waterproof, ignition protection - can be safely installed on gasoline powered ships. Ignition protection for safe installation on gasoline powered boats.. Will be used for the system of 12 - 32 V, 300 A continuous 500 A intermittent, suitable for outboard engines and small diesel or gasoline engines.. The make-before-break contact design allows switching between battery packs without interrupting power.. Tin plated copper has the greatest conductivity and corrosion resistance. The integrated terminal design will not loosen over time.. Battery master disconnect switch serves as a main switch for RV, ATV, car, boat, motorhome, caravan, truck, UTV, etc..

Heavy Duty - Rated at 900 Amps momentary, 500 Amps intermittent and 300 Amps continuous at 12V. Disconnects the battery safely, to eliminate any power draw from the battery when vehicle or boat are not in use.. Great for your boat, RV, show car, trailer, winch power cable, and more. Heavy Duty Switch combined with small footprint.

Blue Sea Systems.

Blue Sea Systems.

Flexible Installation Upgrade This battery disconnect switch comes with a heavy-duty mounting bracket, supporting both surface mount and flush mount installation. Compared to traditional battery switch or battery disconnect, no large panel cutout is required, making it easier to install in tight spaces. Ideal as a battery switch 12V marine, RV battery disconnect switch, or car battery disconnect switch. Heavy Duty Power High Conductivity Built with tinned copper studs, this battery switch ensures excellent conductivity and reduced power loss. Rated at 300A continuous, 500A for 5 minutes, and 900A cranking, making it a reliable heavy duty battery cut off switch for high-load systems such as boat battery switch, marine battery switch, and solar setups. Safe Battery Protection Kill Switch Function This battery kill switch features a simple ONOFF design for quick power shut-off, preventing battery drain and electrical hazards. It functions as a reliable battery shut off switch 12V, battery cut off switch, or battery switch disconnect, helping protect your electrical system when not in use. Waterproof Marine Grade Design Designed for harsh environments, this marine battery disconnect switch features a sealed waterproof housing and flame-retardant materials. Resistant to moisture, corrosion, and outdoor conditions, it works perfectly as a marine kill switch, boat battery disconnect switch, or battery switch 12V marine. Wide Compatibility for Multiple Vehicles Compatible with 12-48V DC systems, this battery disconnect is widely used in boats, RVs, trucks, cars, campers, trailers, ATV and UTV. It serves as a versatile disconnect switch for battery systems, improving safety, reducing power consumption, and extending battery life.

HIGH QUALITY DESIGN Flame retardant PC material shape has good insulation and high temperature resistance. With flexible handle conversion, rotary selector is easy to control, square plate and screws for easily mounting.. EXCELLENT COPPER PARTS Premium copper parts with silver alloy point, make it not easy to slide and has strong thermal conductivity. The quality and service life of changeover switch are improved, it is durable for use.. TECHNICAL SPECIFICATIONS Model LW28-322, 3 positions1-0-2, 2 phases, 8 terminals latching type switch, Ui 690V Ith 32A. Image 3 has shown which terminal will be connected in different position, please read the wiring diagram as a reference.. WIDE APPLICATION RANGE Ideal for electrical wiring in the power switch, speed switch and induction motor, also can make the conversion of the control circuit.. WHAT YOU GET 1pcs x Changeover Switch, 4pcs x Screws. Technical parameters as images show. If you have any question, please feel free to contact us .

Blue Sea Systems.

SpecificationsBattery disconnect switch rated current 240A, rated voltage 12V, standby power consumption 3mA, power-off threshold 11.8V0.2V, instantaneous current 500A.. Magnetic Latching FunctionThis kill switch for car uses a new type of relay that controls circuit disconnection and cut-off by magnetic principle, with a standby current of 3mA, which is more energy-saving.. Automatic Cut OffIf the voltage is lower than 11.8V, the remote kill switch will automatically cut off the power supply after 120s to save electricity, if the voltage is higher than 13.2V, the remote control will be disabled to prevent accidental action to shut off the power while driving, and the power supply can only be controlled by the button on the switch.. Easy InstallationThe power shut off switch uses a negative connection to ensure stable performance. Please remember to turn off the power before installation.. Protect the BatteryUsing this car battery kill switch can avoid power consumption due to long-term parking, good point of electronic equipment, line aging, forgetting to turn off the light, etc. It can effectively protect and prolong the life of car battery..

Note On some models of vehicles, after the remote control of this product is used to disconnect the vehicle battery and turn it on again, you need to wait about 6s before pressing the vehicle start switch to start the vehicle.. For facilitate installation, the black negative wire has been installed at the bottom of the battery switch. This product needs to be connected to the original negative wire on the car. If you mind this change, we recommend that you can choose the 250A Upgrade model. Please pay attention to the installation instructions If your car stereo can not be completely power off, then once you use our product to completely disconnect the battery, the stereo needs to be re-matched when you start the vehicle again. REPLACEMENT REMOTE BATTERY DISCONNECT SWITCH - Wireless kill switch enables you to kill your car battery power with remote control, which can help to prevent battery drain and protect the circuit. Besides, car battery disconnect switch can disconnect the power of your car, the theif cannot start and stole your car. Just press the remote control button to disconnect your car power system, easy to use and improve security. WIDE APPLICATIONS - Remote battery disconnect switch works well for Car, Truck, RV, Travel Trailer, Camper, SUV, ATV, UTV, Marine, Van, Boat, Agricultural Vehicle Trike Auto Off Road Jeep and other engine applications with a 12 volt battery.. PREMIUM QUALITY - Kill Switch for Car is made of silver contact and pure copper wires. Durable and Reliable. Rated current 200A DC12V, this Battery Disconnect Isolator is upgraded from the old model as the improved fittings make mounting contacts stronger. All required wiring harnesses included, no need to buy additional accessories.. EASY INSTALLATION - No modifications needed Step 1 Connect the red wire to the positive pole of the battery. Step 2 Fix the battery clip to the negative pole of the battery. 12V battery disconnect switch allows you not to open the hood every time for turn on the power, just press the remote control key button to disconnect your car power system, saving you plenty of time.. BUY WITH CONFIDENCE - FEITON Upgraded Remote Battery Disconnect Switch comes with 1-Year Warranty, if you have any questions when using this dual remote control 12V 200A car wireless remote battery disconnect switch isolator On Off kill master, please feel free to contact us for a replacement. We will reply your email as soon as possible.

Great Product.

Blue Sea Systems Battery Switch m-Series series ONOFF with Knob, part number 6006300, is a Traditional Style Single Circuit ON-OFF switch. Switches a single battery to a single load group. IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protectedsafe for installation aboard gasoline powered boats. Make before break contact design allows switching between battery banks without power interruption. Continuous Rating 300A, Maximum Voltage 48V DC. Premium warranty and support.

Blue Sea Systems.

ICON Label Set Included for Circuit Identification.. Label with International ONOFF Legends.. All Non-Corrosive Marine Grade Metals.. Product Dimensions 2.9H x 2.9W x 3.1D.. Weight 0.8lbs..

Heavy Duty ABS plastic housing, durable made for safety use, rear cover insulates terminals against any short of circuits. Design for 2 batteries vehicles, can switch battery 1 battery 2 separately or both on and off.. Purpose eliminate any power from the battery when vehicle or boat is not in use, disconnects the battery safely.Avoid battery drain off.. Operation 1-2-Both-Off,4 positions, 200A continuous at 12VDC, 300A intermittent at 12VDC, 1000A momentary at 12VDC.. Compatible used for 12 - 48VDC systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.Widely used for cars, marine boats, RVs, campers, travel trailers, trucks, ATVs, UTVs, battery banks and other devices.. Package include1x battery switch,4 boltsscrews incuded..

Switches isolated battery banks to all loads or combines battery banks to all loads. Ignition protectedsafe for installation aboard gasoline powered boats.. IP66 waterproof, ISO 8846 and meets ABYC requirements. Accepts two 40 AWG 95mm battery cables. Terminal Stud Size 12. Continuous Rating 500A, Max Voltage 32VDC.

WATERPROOF STURDY The heavy duty cut off switch is made of ABS plastic housing and copper tin plating inner stud. Fully enclosed design to protect wiring from dirt, corrosion, and rain.. SAFETY PROTECTION This battery on off switch can isolate and secure the electrical system eliminate any power draw from the battery when vehicle is not in use, disconnects the battery safely provide a reliable way to shutdown electrical power during maintenance and protect batteries from excessive drain. ROTATE BUTTON FOR EASY OPERATION OnOff 2 position, Suitable for various 12V 24V 36V 48V systems. Rating 275A DC Continuous 1hr, 455A DC Intermittent 5 min, 1250A DC Cranking 10 sec. Clockwise to turn on , counter clockwise to turn off. WIDE APPLICATION This master battery shut off switch is universal used for RV, Marine, Car, Boat, Camper, Travel Trailer, Truck, ATV, UTV battery and other engine application, makes it an effortless job of turning the battery on and off. PACKAGE INCLUDE Equiped with 1 Battery Switch, 4 Pcs Mounting Bolts, 4 Pcs 238 Copper Ring Terminals, 4 Pcs Heat Shrink Tubings and a hex wrench, which can provide great convenience for your installation..

Specification Spurtar battery disconnect switch is rated for 200 amps continuous, 455 amps intermittent, and 1000 amps cranking. Voltage 12V-48V DC. Stud Size 3x 516 8mm. Dual 1-2-Both-Off Battery Switch With a battery shut off switch you can ON or OFF or both ONOFF a group of loads irrespective of their individual ONOFF switch control. Heavy Duty Boat Battery Switch Made ABS plastic housing, and the 4 sets of bolts is tinned copper studs3x 516 8mm. Marine battery kill switch Fits into the contour lock system allowing it to be a stand alone unit, or locked together with other switches. Safe Protective Battery master disconnect switch certificated by CE, and 4 removable side plates, the rear cover insulates terminals against any short of circuit. Please rest assured to choose as your rv battery switch disconnect atv battery switch. Widely Use Marine battery selector switch isolator switch is well suited to larger vessels and can be recess or surface mounted. Also widely used for RV, ATV, car, marine boat, camper, camper, travel trailer, truck, UTV, etc.

PREMIUM MATERIAL Crafted from ABS and tinned copper, our marine battery disconnect switch offers rustproof durability, unmatched strength, and a sturdy construction for long-lasting use. PROFESSIONAL DESIGN Experience professional-grade manufacturing and exquisite workmanship with our heavy-duty 4-position battery switch OFF1212. Designed to withstand tough conditions, it ensures a secure connection without easy loosening. EXCELLENT PERFORMANCE Enjoy superior electrical conductivity, IP66 rating, ignition , stable performance, and high reliability with our power kill switch. This switch offers peace of mind and consistent functionality. SIMPLE INSTALLATION Convenient and user-friendly, our battery selector switch features mounting holes that accept 14in M6 screws and 12in terminal studs. Easy installation saves time and effort, providing hasslefree usage for your convenience. FUNCTIONALITY AT ITS BEST The make before breakcontact design allows seamless switching between battery banks without power interruption, boasting a continuous rating of 500 amperes. Effortlessly control power distribution with this efficient feature.

Function Make before break contact design allows switching between battery banks without power interruption, with 500 amperes continuous rating.. Excellent Performance Power kill switch has good electrical conductivity, IP66 waterproof, ignition protection, stable performance and high reliability.. Premium Material Battery switch is made of premium ABS and tinned copper material, rustproof, high strength, sturdy and durable.. Professional Design Professional manufacturing, exquisite workmanship, heavy duty, 4 position OFF1212, not easy to loosen.. Simple Installation The installation is simple, mounting holes accept 14in M6 screw, 12in M12 terminal stud, convenient for using, save your efforts..

Simple Installation The installation is simple, mounting holes accept 14in M6 screw, 12in terminal stud, convenient for using, save your efforts.. Premium Material Battery switch is made of premium ABS and plated red copper material, rustproof, sturdy and .. Excellent Performance Good electrical conductivity, IP66 waterproof, prevents a strong spray of water, with ignition , and reliable.. Wide Application 500 amp continuous rating suitable for outboard and small petrol or engines, ideal for RV or boat.. Function The make before break contact design allows switching between battery packs without interrupting power supply, with AFD..

Current Rating 300A continuous current capacity, suitable for heavy-duty marine and automotive applications. Design IP66 rated enclosure provides complete protection against water ingress and dust. Material Construction Premium ABS housing with tinned copper terminals for resistance and durability. Installation Standard 38 inch M10 mounting studs for easy and secure installation. Switch Positions 3-position design OFF-1-2 allows flexible battery bank selection without power interruption.

Versatile and Efficient Power Control Our battery switch offers powerful functionality with its 3 position, 3 stud dual circuit design, allowing you to switch a single battery to a single load group. It is the choice for marine or RV applications, providing power control and ensuring the smooth of your electrical systems. Easy and Flexible Installation Options With its ignition , our battery switch can be safely installed aboard gasoline powered boats. The versatile case design allows for surface, front panel, or rear panel mounting, giving you the flexibility to adapt to your specific installation requirements with ease. Maximum Conductivity for Optimal Performance The battery switch features an isolating ABS plastic shell and a red copper plated silver inner core, ensuring optimal conductivity and minimizing energy loss. This combination of materials guarantees stable and efficient power , providing performance for your electrical systems. for Battery Banks Our 300A battery switch is designed to isolate potentially destructive energy in the battery banks when your boat is not in use or during emergencies. This ensures the safety and longevity of your battery and electrical systems, giving you peace of mind while on the water or during critical situations. User Friendly Design with IP66 Featuring a label with OFF-1-2, a rotary actuator, and IP66 , our battery switch offers ease of use and durability. The clear instructions and design make it easy to navigate and operate under various weather conditions, ensuring performance even in challenging environments. This user friendly design makes the battery switch an essential component for ships, yachts, RVs, large trucks.

BETTER CONDUCTIVITY LONGER SERVICE LIFE You will be pleasantly surprised when you receive our products Compared with other battery switches, this battery isolator has a smoother surface, heavier weight and easier operation, thanks to our quality control. The heavy duty cut off switch uses a better nylon 66 shell, high temperature resistance effect is better, more safe to use The internal screw of the cutoff switch uses copper plated silver silver contacts, which has better electrical conductivity, oxidation resistance and longer service life. LED DIGITAL VOLTMETER DISPLAY The battery isolator switch surface is equipped with an LED voltage display, allowing you to better monitor the battery status at any time. When the battery switch is on, the upper button screen monitors the voltage in real time. When the master disconnect switch is off, the screen does not display. COMPATIBILITY SAFETY This Battery Kill Switch Used for DC 5 - 60V systems to isolate and secure the electrical system eliminate any power draw from the battery when vehicle is not in use, disconnects the battery safely provide a reliable way to shutdown electrical power during maintenance and protect batteries from excessive drain. EASY TO OPERATE OnOff 2 position, Suitable for various 6V12V24V48V60V systems. Current 250A Continuous at DC 12V 300A for 30 minutes. Clockwise to turn on , counter clockwise to turn off. WIDE APPLICATION Battery isolator switch is universal used for RV, Marine, Car, Boat, Camper, Travel Trailer, Truck, ATV, UTV battery and other engine application, makes it an effortless job of turning the battery on and off. PACKAGE INCLUDE Equiped with 1 Battery Switch, 4Removeable Side Plate, 1Rubble Gasket, 1Rear Cover, 4Nut, 4Screw, 128 Terminal.

FUNCTION This M-Series Battery Switch with OnOff position acts as a power cut off, eliminating any power drain from the battery pack. Disconnect the batteries safely when the vehicle or boat is not in use.. DESIGN Make-before-break contact design allows switching between battery banks without power interruption.. IGNITION PROTECTION The battery disconnect switch has a crank rating of 900A for 30 seconds, 500A for 5 minutes, and a continuous rated current of 300A. Maximum Operating Voltage 48V.. ABOUT MOUNTING This battery switch can be safely mounted on gasoline powered boats, the chassis design allows for surface, front panel or rear panel mounting.. WIDE APPLICATION This red battery cut off switch is ideal for RV, travel trailer, marine, boat, camper, truck, ATV, UTV, etc..

Application 3position 3stud dualcircuit battery switch, switches a single battery to a single load group. Ideal for marine or RV applications.. Function 300A battery switches can isolate the potentially destructive energy in the battery banks when boat is not in use or during emergencies.. Flexible Installation ignition for installation aboard gasoline powered boats. Case design allows surface, front panel, or rear panel mounting.. Circuit Identification Label with OFF12, rotary actuator, IP66 waterproof . Installed in the circuit, directly installed for use.. Good Conductivity Isolating ABS plastic shell and red copper plated silver inner core for maximum conductivity..

Selector 4 Position. Switches isolated battery banks to all loads or combines battery banks to all loads. Ignition protectedsafe for installation aboard gasoline powered boats. IP66 waterproof, ISO 8846 and meets ABYC requirements. Terminal Stud Size 38 - 16. Continuous rating 350A, Maximum voltage 32V DC.

Operation 1-2-Both-Off, Rating 200A DC Continuous 1hr , 300A DC Intermittent 5 min, 1000A DC Cranking 10 sec, Voltage 48V DC, Stud Size 3x516 8mm. Please note Selector switches will not separate electronics from harmful engine starting spikes. Offers a simple economic way of separating two batteries. Tin-plated copper studs and nuts. Three removable side plates for access of up to 10 cables plus a rear cover insulating the rear terminals against any short circuits. This ensures the switch meets ABYC requirements. Ignition protected.

Heavy duty selector switch. Offers a simple economical way of separating two batteries. Housed in the same module as the 720, it includes the same removable plates and back cover. Fit type Universal Fit.

Polycarbonate body with brass terminals. Ignition protected. For use with 6 to 50 volt Marine Electrical Systems. 90 rotation feature allows users to feel the switches' position in no light situations and the classic shape of the knob makes it easy to turn. Optional spacer ring PN 0462DP0RED allows for the use of larger cables.

Battery selector switch for use with 6, 12, 24, and 32 volt marine electrical systems. Rated at 380 amps continuous, 850 amps intermittent 5 minutes on, 5 minutes off. Easy Installation. Built with quality materials.

Polycarbonate body with brass terminals. Dimensions 4 width x 4 height x 3 depth, 38 teminal size. For use with 6 to 50 volt marine electrical systems. Capacity - 315 AMPS Continuous, 450 AMPS 5 Mins. Intermittent. Ignition protected.

Versatile use for 6-volt to 32-volt D. C. direct current systems. Rated for 300 amps continuous use at 6 volts and 150 amps continuous use at 12 volts. Includes an automatic alternator field circuit disconnect to prevent surges and so, protect your valuable boat electronics. Rugged build features Bakelite housing, copper washers, and solid brass terminals and nuts. Attwood products are both compatible and reliable, engineered and built with a never-fail attitude. Sport type Boating.

Guest 2300A Diesel Power Battery Selector Switch 2300A.

VERSATILE BATTERY DISCONNECT SWITCH This 12V 24V knife blade battery cut off switch is perfect for cars, marine vessels, RVs, pickups, boats, ATVs, and more, ensuring your battery stays preserved when not in use.. TOP POST BATTERY KILL SWITCH Equipped with a top post design, this battery power shut off isolator switch provides a convenient way to disconnect the NEGATIVE terminal of your battery, preventing drainage and extending its lifespan.. EFFICIENT POWER MANAGEMENT The vertical orientation of this battery disconnect switch allows for easy access and operation, making it a practical choice for quickly cutting off power to your vehicle or equipment when necessary.. DURABLE RELIABLE CONSTRUCTION Crafted from high-quality materials, this battery disconnect switch is built to withstand tough environments, ensuring long-lasting performance and dependable power isolation whenever needed.. SIMPLE INSTALLATION OPERATION With its user-friendly design, this battery isolator switch can be easily installed and operated, offering a hassle-free solution for safeguarding your battery and preventing unintended power consumption..

1-Click Protection - Upgraded Heavy Duty 250ATap the keychain remote to immediately cut off power, thwarting potential theft and halting parasitic battery drain. Whether parked in a bustling lot or stored remotely, your car, RV, truck, trailer, ATV or marine boat remains safely guarded, particularly useful for long-term parking, anti-theft measures, car wiring changes, accidentally leaving lights on, and dealing with aging wiring. WARNING PLEASE ENSURE ALL SCREWS ARE SECURELY TIGHTENEDONLY FITS POST DIAMETER RANGE 15-17MM TAPERED. Dual Control Mode - Remote Manual ConvenienceSwitch effortlessly between the compact remote for everyday ease and the manual ONOFF button. The battery disconnect switch features 5 bright green LEDs that light up to confirm each action, eliminating uncertainty about your vehicle's protection status. Extend the external black spring-shaped antenna for enhanced remote range. EXTEND EXTERNAL BLACK STRING-SHAPED ANTENNA FOR ENHANCED REMOTE DISTANCE.. Smart Voltage Guardian - 1224V Wide Voltage CompatibilityThe kill switch constantly monitors battery voltage. In smart mode, if the voltage drops below 11.4V, the remote control function is disabled to prevent accidental shutdowns. The switch operates normally within voltage ranges of 11.4-14V or 23-27V, ensuring your battery is always safeguarded. If the battery voltage is below 6.5V, the device will not function. For voltages between 6.5V and 11V, remote control is not available, but manual control is supported. DO NOT USE THIS BATTERY DISCONNECT SWITCH ON INDUSTRIAL EQUIPMENT. Long-Lasting Performance - Ultra-Low Standby CurrentWith a standby current of just 0.007mAsignificantly lower than the original vehicle's 65mAthis kill switch ensures your battery stays charged even during extended periods of inactivity, providing reliable long-term protection. PLEASE DON'T DISASSEMBLE THE DEVICE ON YOUR OWN TO AVOID DAMAGING THE CIRCUIT BOARD, WHICH MAY AFFECT THE NORMAL USE OF THE PRODUCT. Premium Copper Anti-False Contact Protection - Durable ReliableCrafted from high quality copper, this battery cutoff switch boasts enhanced durability and reliability. This upgraded model features enhanced accessories for a more secure installation, advanced design to prevent false contact issues, and ensures a stable, safe connection with superior, lasting performance..

Simple Installation The installation is simple, mounting holes accept 38in M10 terminal stud, convenient for using, save your time and energy.. Wide Application Power kill switch with 300 amp continuous rating suitable for outboard and small petrol or engines, ideal for RV or boat.. Premium Material Battery switch is made of premium ABS and tinned copper material, wear resistant, rustproof, sturdy and durable.. Function Make before break contact design allows switching between battery banks without power interruption, with 3 position OFF12.. Excellent Performance Battery disconnect switch has good electrical conductivity, IP66 waterproof, ignition protection, safe and reliable..

1-2-BOTH-OFF SWITCH - This Battery Disconnect Switch 12V features 1-2-Both-Off 4 Position Rating 200A continuous at 12VDC, 300A intermittent at 12VDC, 1000A momentary at 12VDC. Stud Size 2x38 10mm. It is designed for 2 batteries, can switch to battery 1, battery 2, both batteries connect or both disconnect.. SUPERIOR QUALITY - The battery kill switch is made of high quality ABS plastic, the copper terminal studs with nuts and washers, which makes it more durable and safer to use, rear cover insulate terminals against any short of circuits.. SAFETY PROTECTION - This Waterproof Battery Switch 12V can disconnects the battery safely, protect batteries from excessive drain when vehicle or boat is not in use.. WIDE APPLICATION - This battery shut off switch is suitable for DC 12 - 48V system to isolate and secure the electrical system, can stand alone or be locked together with other switches. It is widely used for Car, Marine, Boat, RV, Camper, Travel Trailer, Truck, ATV, UTV, Battery banks and other electrical equipment's switch.. PACKAGE INCLUDE - Package includes 1 Battery Switch, 4 stainless steel mounting screws and caps to help fix the switch tightly. For any problems, please do not hesitate to write to us..

SIMPLE EASY SETUP Directly connects to standard side post batteries negative 17-19mm terminals with no modifications. Effortless installation in under 5 minutes, eliminating complex wiring or extra parts. Please note this battery disconnect switch always requires much force to rotate on and off to ensure stable operation.. RELIABLE POWER ISOLATION Designed for 12-48V DC systems, instantly cuts off battery drain during vehicle storage and supports 275A continuous 500A intermittent 1300A momentary current 12V. Ideal for cars, boats, RVs, ATV, marines and seasonal equipment to prevent accidental discharge.. BUILT FOR TOUGH ENVIRONMENTS Reinforced ABS housing resists extreme temperatures and moisture. Smooth switching mechanism ensures long-term reliability. UNIVERSAL COMPATIBILITY Fits most of top-post batteries, including common automotive and marine models. Compact design adapts to tight spaces without interfering with existing systems. EXTENDED BATTERY LIFESPAN Safeguards against parasitic power loss, proven to maintain battery health during extended inactivity. Backed 247 support..

For use with 12, 24 and 32 Volt Marine Electrical Systems. Capacity - 250 AMPS Continuous, 360 AMPS Intermittent. Ignition Protected. Built with quality materials.

Permits selection between batteries for starting, charging or operation in parallel. For use with two or more batteries and systems under 50V. UL listed, ignition protected and CE approved. Capacity 250A continuous, 360A intermittent. Size 5-14 inch x 2-58 inch. Manufacturer part number 50-11501.

High Conductivity Power Control - Pure copper contact structure provides high electrical conductivity and low resistance, supporting stable current transmission and reduced energy loss. Helps maintain consistent power flow and reliable circuit performance during daily operation. Designed to minimize voltage drop and improve overall battery system efficiency in automotive and marine applications. Simple Manual Rotary Switch - Manual rotary design allows fast and direct power control without electronics. Rotate the switch 90 degree upward to cut off battery power, and rotate downward to restore power. Easy to understand and operate, suitable for users who prefer mechanical control with clear on and off status and no learning curve. Battery Drain Prevention - Disconnects battery power when the vehicle or equipment is not in use, helping reduce parasitic drain and unnecessary energy consumption. Supports extended battery service life during long-term parking, storage, or seasonal use. Ideal for vehicles that sit idle for extended periods without frequent charging. Wide 12 Volt And 24 Volt Compatibility - Compatible with both 12 volt and 24 volt battery systems, making it suitable for a wide range of vehicles and equipment. Commonly used in cars, trucks, RVs, boats, trailers, campers, and marine battery setups. One switch supports multiple use scenarios without complex configuration. Compact Size And Easy Installation - Compact structure fits standard battery terminals and common battery layouts. Designed for straightforward installation using basic tools, with no complex wiring or modification required. Suitable for vehicle owners, RV users, and boat owners seeking reliable battery power management with low maintenance requirements.

Wide Application Designed for a wide range of applications, the battery disconnect switch is ideal for marine, RV, gasoline-powered boats, battery applications, and electrical equipment to meet your needs.. 3-Position Battery Selector Switch The battery disconnect switch can switch a single battery to a single load group, suitable for situations where a simple battery management system is required. AFD Alternator Field Disconnect is included for practical use.. Marine Use Our battery master switch has an IP66 waterproof rating, making it resistant to powerful water jets it also provides ignition protection and can be safely installed on gasoline-powered boats.. Conductive Tinned Copper Stud The battery disconnect switch accepts battery cables up to 40 AWG, and the stud accepts 12-inch M12 ring terminals. The 78-inch 22 mm stud length accepts multiple cable terminations.. Flexible Installation The housing design of this battery switch allows for surface, rear panel, or front panel mounting options, adding installation flexibility. Tactile indicators sense knob position for ease of use..

FITMENT COMPATIBLE This switch is used on TOP POST battery DC 12V - 48V only, standard top post battery size 19 mm conetapering positive 17 mm conetapering negative, hook up to TOP post battery NEGATIVE directly. Installation SPACE should be checked to prevent incompatible.. Convenience direct fit and no modifications, hook up to TOP post battery negative directly, do not need additional battery cables or lugs, isolate and secure the electrical system easily.. Specification used for DC 12 - 48 V systems, ONOFF 2 positions, 275 A continuous at DC 12V, 455 A intermittent at DC 12V, 1250 A momentary at DC 12V.. Heavy Duty ABS plastic housing, durable made for safety use. Extended the top post battery negative to original size standard top post negative 17 mm conetapering negative -.. Purpose Can stand alone or be locked together with another switch. Eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely, widely used for car, vehicle, Rv and boat..

MORE STURDY, BETTER CONDUCTIVITY Compared with the traditional ABS plastic shell material, the heavy duty cut off switch uses a better nylon 66 shell, high temperature resistance effect is better, more safe to use The internal screw of the cutoff switch uses copper plated silver silver contacts, which has better electrical conductivity, oxidation resistance and longer service life.. LED DIGITAL VOLTMETER DISPLAY The battery isolator switch surface is equipped with an LED display, which displays the current voltage status in real time, allowing you to better monitor the battery status at any time. When the battery switch is on, the upper button screen monitors the voltage in real time. When the master disconnect switch is off, the screen does not display.. COMPATIBILITY SAFETY This Battery Kill Switch Used for DC 5 - 60V systems to isolate and secure the electrical system eliminate any power draw from the battery when vehicle is not in use, disconnects the battery safely provide a reliable way to shutdown electrical power during maintenance and protect batteries from excessive drain.. EASY TO OPERATE OnOff 2 position, Suitable for various 6V12V24V48V60V systems. Current 250A Continuous at DC 12V 300A for 30 minutes. The standby current is 0, and the LED digital display screen consumes 30ma when it is turned on. Clockwise to turn on , counter clockwise to turn off.. WIDE APPLICATION Battery isolator switch is universal used for RV, Marine, Car, Boat, Camper, Travel Trailer, Truck, ATV, UTV battery and other engine application, makes it an effortless job of turning the battery on and off.. PACKAGE INCLUDE Equiped with 1 Battery Switch, 4Removeable Side Plate, 1Rubble Gasket, 1Rear Cover, 4Nut, 4Screw, 128 Terminal. If you have any questions,please contact us via email. We are always here to support you..

Easy to Use Turning it on powers up your system, turning it off cuts the power.It can handle 275 Amps of continuous DC power for up to 1 hour, 455 Amps intermittently for 5 minutes, and 1250 Amps for cranking power lasting 10 seconds. It has 2x38 10mm studs.. Sturdy Construction This battery disconnect switch is built with a tough ABS plastic housing, tinned copper studs, and nuts. It includes 4 stainless steel mounting screws and caps for secure installation. You can easily access battery cables with 4 removable side plates.. Safety First The battery shut-off switch disconnects your battery safely, preventing excessive drain when your vehicle or boat isn't in use.. Versatile Compatibility This quick disconnect switch is designed for 12-48V DC systems, allowing you to isolate and secure your electrical system. It can work independently or be locked together with other switches, offering a simple and cost-effective way to separate batteries.. Wide Range of Uses This universal switch is suitable not just for cars, RVs, trucks, and marine boats but also for various electrical equipment, like flashing lights, chassis lights, fog lights, and dome lights..

Wide Application Battery isolator switch is universal used for Car, Van, Caravan, RV, Truck, Marine Boat, Camper, Travel Trailer, Battery Box, ATV, UTV or or any vehicle where a battery cut-off switch is required.. Compatibility Benefits Used for DC 12 - 48V systems to isolate and secure the electrical system eliminate any power draw from the battery when vehicle is not in use, disconnects the battery safely provide a reliable way to shutdown electrical power during maintenance and protect batteries from excessive drain.. Heavy Duty Construction Sturdy durable ABS housing, rear cover insulates terminals against any short of circuits 4 removable side plates provide access of up to 10 cables Tin-plated copper studs and nuts for strong oxidation and corrosion resistance. Simple Operation OnOff 2 positions 0Off, 1On, 275A continuous at DC 12V, 455A Intermittent at DC 12V, 1250 A momentary at DC 12V Voltage 12V- 48V DC Terminal Stud Size 2x38 10mm. Buy with Confidence Package Include 1 x battery switch 4 x mounting bolts. 12 Months warranty guarantee for refund or replacement of any defective one.

Features This battery disconnect switch features a conductive tinned copper stud. Accepts battery cables up to 40 AWG, and the stud accepts 12-inch ring terminals. 78-inch 22 mm stud length accepts multiple cable terminations.. 3-Position Battery Selector Switch Switches a single battery to a single load group. Includes AFD Alternator Field Disconnect. Housing design allows for , rear panel, or front panel mounting options tactile indicator senses knob position.. IP66 IP66 rated marine battery switch, can withstand strong water jets, can adapt to marine environments for a long time, with can be safely installed on boats.. Wide Application The switch positions of this On-Off Battery Switch are OFF, 1, 2. Ideal for marine, RV, gasoline-powered boats, battery applications, and electrical equipment.. and Made of high-quality ABS and copper wire, it has good conductivity, and ABS can well the switch and have a longer service life..

Switches a single battery to a single load group Ignition protected - safe for installation aboard gasoline powered boats. IP66 waterproof, ISO 8846 and meets ABYC requirements. Accepts two 40 AWG 95mm battery cables.. Terminal Stud Size 12. Continuous Rating 600A, Max Voltage 32VDC.

Blue Sea Systems Battery Switch m-Series Selector, part number 6007, is a Selector 4 Position switch. Switches isolated battery banks to all loads or combines battery banks to all loads. IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protectedsafe for installation aboard gasoline powered boats. Make before break contact design allows switching between battery banks without power interruption. Continuous Rating 300A, Maximum Voltage 32V DC.

Includes AFD Alternator Field Disconnect. Compact design makes installation in tight places easy. Multiple mounting options can be installed on the surface or rear of the panel. Ignition protected and can be mounted in the engine room of gasoline powered boats. One piece copper studs are 78 long and accept multiple cables.

ENHANCED POWER MANAGEMENT The Battery switch has a Continuous rating of 350A, and a maximum Operating Voltage is 32V. The Battery Switch enables swift transitions between two batteries for accessory power, ensuring one remains at full capacity for rapid engine starts. Alternatively, it allows for combining two batteries to enhance available power, addressing any power-related challenges.. SUPERIOR QUALITY Our Battery switches feature durable heavy-duty plastic housing with Nickel Plated Copper studs, providing excellent weather resistance and an extended service lifespan. With an IP66 waterproof rating, ISO 8846 compliance, and adherence to ABYC requirements for the Boat, this Battery Switch is also ignition-protected, ensuring safe installation on gasoline-powered boats. These features make it an intelligent choice for your needs.. WIDE APPLICATION Our battery switch is universally used for Boat, Ship, and Yacht batteries, making it an effortless job to switch between the batteries. Always remember to turn off your engine before disconnecting the battery.. EASY TO OPERATE Battery disconnect switch with 4 positions. switched 1 or 2 to accessory power while keeping one at 100 for fast engine starts Switched 12 to boost available power by combining two batteries to solve any power situation Switched OFF to disconnect the circuit from power.. 100 LIFETIME PROTECTION Enjoy reliable performance with our lifetime protection, ensuring that your product will always be covered for any defects or issues that may arise..

MaterialThe quality of this battery isolator 12v is guaranteed and its long service life can bring you a good use experience. Its robust pure copper build ensures consistent operation, making it a dependable component for your vehicle's electrical system. And it is very safe and strong. Our rotary battery disconnect switch can ensure smooth current transmission, reduce power loss, and ensure stable operation of the circuit system.. FeaturesOur switch for car features innovative adjustable terminals that can be rotated to accommodate various wiring angles and spatial constraints. This flexible design significantly simplifies the installation process, allowing for a more customized and secure fit in different vehicle engine compartments. This characteristic makes the battery isolator a practical solution for a wide array of automotive and marine applications, ensuring hassle-free setup and reliable connections.. Easy To UseThis switch has two states, when the switch is raised 90 power-off state, the switch is lowered 90- power-on state. Our car battery cut off switch products are simple and easy to use, saving time and effort during use will bring you a good use experience. When the battery is not in use, it can be powered off to protect the battery life. It has good corrosion resistance, can adapt to different environmental conditions, and reduce maintenance costs.. Wide ApplicationsThe battery isolator is widely used in battery systems for various types of cars, including small vehicles such as sedans and sports cars, land vehicles such as trucks and vans, and water vehicles such as yachts. By effectively preventing battery drain during periods of inactivity, this switch helps to prolong battery lifespan. Our smart car battery disconnect switch products are widely used and suitable for a variety of 12V and 24V battery systems.. What You Will GetYou will receive one battery switch 12v, one wrench for easy tightening, and one shim to ensure a secure and precise fit on the battery terminal. This product is not easy to damage and can be used with confidence. If you have any questions about our product during using cotton sticks, please tell us and we will solve the problem for you as soon as possible. We sincerely hope to bring you a pleasant experience..

Rated to 180A Continuous or 1000A Intermittent. Mounts in 34 Hole or Add Fastronix 980-000 Switch Mount to Install on any Surface with Two 14 Holes.. Provides Single Power Cut off to Entire Electrical System. Required for NHRA Competition When Battery is Relocated. Works Great As a Power Disconnect for RV's When Not in Use. Fastronix 404-110 Terminal Covers Provide Electrical Protection to the Studs.

On Off Battery Switch This top post battery disconnect switch features onoff 2 position Rating 250A DC Continuous,1000A DC Cranking Circuit Type 2 way Operating Voltage 12-48 Volts. The OnOff functionality is straightforward yet effective, offering an easy way to manage power without fuss. Ease of Installation This battery disconnect switch 12v 48v comes with negative battery clamp and tapering post. Our marine battery switch is installed on the negative of the battery, our unique design also makes your installation more convenient and simple compared with other's. Superior Quality The battery cut off switch is made of high quality ABS plastic, durable for safe use. It also comes with copper battery clamp and tapered post, which is safer and more reliable in electrical conductivity. Safety Protection This marine battery switch 12v can safely disconnect the battery, protecting batteries from excessive discharge when vehicle or boat is not in use. Wide Application This top post battery disconnect switch is suitable for DC 12 - 48V system to isolate and secure the electrical system, can stand alone or be locked together with other switches. It is widely used for Car, Marine, Boat, RV, Camper, Travel Trailer, Truck, ATV, UTV, Battery banks and other electrical equipment's switch.

Dual Circuit Car battery disconnect switch is dual-circuit. When the old power supply fails, battery disconnect switch 12v heavy duty can immediately switch to the backup power supply, effectively ensuring the normal working and power safety of the car. Battery Switch Marine battery disconnect switch operating Voltage 12-48V, 3 position, 4 gear off-1-2- 12, Screw M10x3. The package contains 1pcs marine battery disconnect switch and a cover excluding the hardware for connecting the back cover. Industrial Material Marine battery switch is made of industrial materials. Stable conductivity of brass can ensure that the power supply isn't interrupted. The ABS insulation material is suitable for outdoor and can ensure power safety of battery switch. Easy to Install Boat battery switch is easy to install. You can directly replace the original battery power off switch or use a matching cover to install it in another position. Install the car battery shut off switch by yourself, saving time and energy. Widely Used Battery selector switch has a wide range of uses, suitable for cars, ships, trucks, campers, battery combination lights and other equipment. And the dual-circuit 12v battery disconnect switch can ensure normal driving on long roads or at sea.

Intelligent Anti-Misoperation Dual Mode OperationSystem locks power-off commands once the engine runs, preventing accidental shutdowns or damage while driving.Operate via manual switch if remote fails, ensuring reliable vehicle start in any situation.compatible with Recessed Flat battery.

Polycarbonate Body with Brass Terminals. Ignition Protected. For use with 6 to 50 Volt Marine Electrical Systems. Built with quality materials. Terminal Stud Size 38.

Requires 13 rd less space to mount.. OnOff selector versions.. Popular 90 easy to identify position rotation.. New smooth rotary action..

Prevents Battery Drain During Storage Frustrated with a dead battery after parking your RV, boat, or vehicle for weeks This car battery kill switch eliminates parasitic drain from clocks, radios, ECUs, and alarms. Flip it to OFF and preserve your battery's charge for months. Works for both 12V and 24V systems.. Heavy-Duty Internal Construction Inside the impact-resistant ABS shell are high-conductivity copper contacts engineered for stable performance. Adopts thickened conductive structure, supports heavy starting current, perfectly fits V8 engines, diesel vehicles and marine motors, effectively avoids overheating and voltage drop during use.. Adjustable Design for Easy Installation The terminal features a large-angle adjustable design that can be rotated to fit different wiring angles and tight engine spaces. Fits standard 16mm-19mm posts on both positive and negative terminals. Negative terminal recommended for maximum safety. Comes with a wrench and washers for a secure fit.. Universal Fit for All Vehicles Equipment One switch works across all your vehicles. Ideal for Cars, Trucks, SUVs, RVs, Campers, ATVs, UTVs, Boats, Yachts, Marine, Tractors, Forklifts, and Heavy Equipment. Simple DIY installation no special tools required.. Complete Kit What You Get Everything you need is in the box 1 x QMPRKPE Battery Disconnect Switch, 1 x Wrench, 1 x Washer. Designed for DIY installation no special tools or professional skills required. If you have any questions, contact us we respond within 24 hours..

Recoil battery switches are used for DC 12 -48V systems to isolate and secure the electrical system. They prevent any current from being drawn from the battery when vehicles or boats are not in use.. Our switch features 1-Off-2 3-Position simple design. It is easy to read and to operate, simply turn the knob to switch a single battery to a single load group.. Operation 250 A continuous at DC 12V, 400 A intermittent at DC 12V, 800 A momentary at DC 12V.. Heavy duty ABS plastic housing is super durable for safety use. Rear cover insulates terminals against any short of circuits. The 38 M10 studs nuts are made of copper for maximum power transfer.. They are designed for frontrear panel mounting, or surface mounting. The stainless screws are included to facilitate your installation.. Recoil battery switches are widely used for Car, Marine, Boat, RV, Camper, Travel Trailer, Truck, ATV, UTV, Battery banks, and other electrical equipment switches..

Ideal Power Switch - With tinned copper inner studs, the boat battery switch has better contact performance and good conductivity, greatly reducing power consumption. Studs Size 2 x 38 10mm. Furthermore, the housing of battery kill switch is made of flame-retardant plastic for safer use in messy or moist environment.. 2 Position Ignition Protected - This battery shut off switch is single circuit ONOFF design, simply turning the knob to ON or OFF position to realize the control of the power circuit. Of course this car battery switch has ignition protection as its crank rating that withstands 900A for 30 seconds, 500A for 5 minutes, and 300A continuously.. Easy to Install - The battery disconnect switch is euipped with mounting screws for easy installation which could save your time and money on extra accessories. The 12V switch shell is easily disassembled, and the space inside the shell is large to complete the wiring tasks. Moreover, the switch base has partition design to reduce interference between wires.. Safe and Practical - This battery cut off switch is suitable for 12-48V DC systems, often used for the control and protection of electrical systems. When the battery is not in use for a long time, this car battery switch can safely disconnected the power supply so that can prevent leakage and reduce energy consumption.. Wide Compatibility - The marine battery switch is usually used with the battery box, fuse block which can isolate and protect the electrical system. This battery switch is widely applied to marine, boat, yacht, car, RV, camper, travel trailer, truck, ATV, UTV, etc. When your RV, boat or car is not in use, the power switch can safely disconnect the battery power, reducing the additional loss of battery power and extending the battery life.

Electric Switch - Shopcorp presents a sturdy yet lightweight selector switch, featuring a two-position self-lock with a 22mm mounting hole for secure installation. This versatile switch can be configured as either NO or NC contact, made with high-grade plastic, metal, and electronic components. It adheres to the GBT14048.5 standard, ensuring reliable performance without the need for batteries.. NO Switch - Certified with CE and CCC, our selector switch operates at 220VAC and 380V, with a current capacity of 10A. It boasts an IP55 protection grade and can withstand extreme temperatures from -25C to 70C, and 50 operating humidity. Engineered for resilience, it endures up to 50,000 mechanical cycles and significant shock and vibration resistance. It's designed for panel mounting and must be securely fixed for optimal performance.. Rotary Switch 2 Position - Tailored for industrial applications, this switch operates flawlessly in AC circuits 50Hz60Hz with up to 380V, and in DC circuits up to 220V. It's perfect for controlling various electrical components under challenging conditions, thanks to its robust lock and resistance to fall and vibration. Its versatility makes it a suitable choice for a wide array of domestic electrical appliances.. On off switch - To install, first you need to screw out the nut and fix the head. Then align the top of the head in the direction of the buckle and put the switch seat on. Finally, turn the buckle to the original position and clamp the head. To disassemble, first you need to pull the head out of the middle seat. Then, hook the convex point of the clasp with the index finger and pull gently. Lastly, move the buckle to the other side.. Latching Switch - Composed of non-flammable and durable materials, our selector switch is suited for environments with fluctuating temperatures. The aluminum alloy circuit provides robust protection for the switch head, enhancing longevity and anti-oxidant properties. Plus, the distinctively designed metal contact base supports a 10A load and is conveniently replaceable, adding to the switch's practicality and longevity..

The Spartan Power mini 300A battery selector switches isolated battery banks to all loads or combines battery banks to all loads. Lifetime Warranty Max 32VDC. IGNITION PROTECTED Spartan Power battery switch has a crank rating of 900A for 30 seconds, 500A for 5 minutes and 300A continuous rating. Maximum Operating Voltage 32V. IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protectedsafe for installation aboard gasoline powered boats.. MOUNTING OPTIONS Case design allows surface, front panel, or rear panel mounting. Screws are now included. NEED CABLES These battery switches pair perfectly with Spartan Power Made in the USA 38 terminated battery cables. Accepts up to 40 AWG battery cables on it's 38 posts..

High Current Battery Switch With a rated current of 200 Amp Continuous, and 1000A Intermittent, Spurtar battery disconnect switch safely isolate and secures 12-48V DC electrical system connections. Safety Protection Spurtar battery switch provides power cut-off to the electrical system, prevents your vehicle from battery drain, and reduces the risk of an electrical fire. When your car, boat, or RV is not in use, disconnect the battery for the safety of your vehicle and property. Easy Operation The battery shut-off switch is toggled smoothly with a clear click sound, without jamming. Spurtar battery cut-off switch with on off indicated face plate is easy to install, and can be for professional installation. Wide Application The RV battery disconnect switch is widely used for heavy vehicles, boats, RVs, campers, trailers, off-road, ATVs, trucks, tractors, forklifts, motors, electric winches, and other electrical equipment. Battery Kill Switch Kit You will get 1x 200 amp disconnect switch, 2x 38 Copper Lugs, 2x Heat Shrinks, 2x Rubber Terminal Insulator Sleeves to prevent incidental shorting and improve the appearance of your wiring.

100M REMOTE CONTROL BATTERY DISCONNECT SWITCH. 100M remote battery kill switch used for 12V equipment that not in use, prevent battery from parasitic drain or as a theft deterrent. Convenient FOB remote control, no need to open the hood to disconnect battery, just a quick button push. The remote is preprogrammed and ready to go out of the box. HEAVY DUTY HIGH CURRENT DEVICE. High current rated to 200A Continuous 1000A Crank Amps. Enough crank amps to start your car in cold weather. This is a high quality solid state relay with a remote control receiver circuit built into it. This switch lasts 3-4 times longer than an ordinary relay switch. ZOZOMOTORS uses high quality durable parts only. The current draw of this switch the remote receiver is 0.001 - 0.005 AMPS while connected. it's very minor. PARTS SPECIFICATIONS ARE ON PRODUCT IMAGE 7 FOR YOU TO VERIFY WHETHER IT FITS YOUR EQUIPMENT. Copper bridges with 38 diameter holes. Relay switch stud terminal size 14 7mm x 2. Recommend install on the NEGATIVE SIDE of the battery. Installation on the positive side is also allowed. This switch can be used to disconnect 12V system including cars, trucks, RVs, boats, and other equipment. EASY TO INSTALL, WIRING DIAGRAM IS PROVIDED. You can check the clearance around the negative pole of your battery refer to product image 3. An easy-to-follow wiring diagram is included in the package. The red and black wires power the remote receiver in the relay and should always go to the positive and negative battery poles respectively. One side stud terminal of the relay goes to the negative pole on the battery, and the other gets the negative wire from the car. REMINDER. This switch is to disconnect power directly from the battery, electronics that store data, like your radio, will lose memory. California users must keep the battery connected without activating the switch for several days before a smog test.

Complete Battery ControlWith power cut-off ability, this device caters to a variety of vehicle models, helping optimize battery life and performance. Suitable for trucks and cars with a wide voltage design supporting 12V and 24V voltages. Enhanced Battery LongevityOur Battery Disconnect extends the battery life and reduces energy consumption of your vehicle. Its anti-leakage protection mechanism prevents accidental battery discharge and assures safety during parking and vehicle use. Experience optimized energy efficiency with this must-have product. Dependable ProtectionBuilt with pure copper for excellent conductivity, Constructed with a rugged build, this sturdy battery disconnect assures continuous performance amidst challenging conditions, ensuring lasting protection for your vehicle's electrical management. Ready to UseOur battery disconnect switches are perfect for esasy vehicle maintenance. With a simple and user-friendly design, users can quickly and easily cut off power to the battery, allowing for easy removal, replacement, or repair. Prevent HazardsBy preventing leakage and assureing excellent conductivity with its pure copper material, our Battery Disconnect provides sturdy and dependable protection, securing your vehicle's electrical system.

Choiceness DesignHeavy Duty ABS plastic housing and tinned copper inner stud, durable and made for safe use. Equipped with 4 sets of bolts. Removable windows can be adjusted as needed. Rating 275A DC Continuous, 455A DC Intermittent 5 min, 1250A DC Cranking 10 sec Stud Size 2x38 10mm.. Widely ApplicationThis battery shut-off switch is suitable for DC 12 - 48V system to secure the electrical system. It is widely used for Car, Marine, Boat, RV, Camper, Travel Trailer, Truck, ATV, UTV, Battery banks, and other electrical equipment switches.. Compatibility and Safety This battery switch is suitable for 12 V24 V36V48 V systems, used for protection of electrical systems When the battery is not in use, avoid unnecessary battery consumption and safely disconnect the battery Provides a convenient and reliable way to turn off the power and protect the battery from excessive consumption.. Easy to Operate2 positions onoff, for use in 12-48V DC systems. Rated value 275A DC continuous , 455A DC intermittent 5 minutes, 1250A DC start 10 seconds.4 detachable baffles are suitable for wiring needs in different scenarios.. Packaging IncludesBattery switch 1, Self-tapping screws 4, Screw Nuts 4, Installation Guide Sticker1, provide great convenience for your installation. If you have any questions, please contact us via email. We have always been here to support you.

Working Condition The working condition for the battery switch is 12V-60V voltage and 0-300A. Applications The battery disconnect is always used as a key part to cut off the current from the battery when it is not working. The switch can be applied to many marine boats RV ATV vehicles and other 12V-60V battery devices.And the switch have four buttons in total, 1-2-both-off. It will separate the battery easily and will let you control the power more convenient.. Material The battery switch outer shell is made of ABS panel and bolts are galvanized, which is totally rust and corrosion resistant.. Package The package comes with a battery disconnect and four stainless steel screws. Warranty We offer one year warranty for the blade switch. If you are not satisfied with it, simply contact us and get your refund..

Customized Design Heavy Duty design for 2 batteries, can switch to battery 1 battery 2 separately or both and off together. ABS plastic housing, durable made for safety use, equiped with 4 sets of bolts.. Operation 1-2-Both-Off 4 positions, 200 A continuous at DC 12V, 300 A intermittent at DC 12V, 1000 A momentary at DC 12V.. Compatible used for DC 12 - 48 V systems to isolate and secure the electrical system, can stand alone or be locked together with other switch.. Purpose eliminate any power draw from the battery when vehicle or boat is not in use, disconnects the battery safely.. Copper terminal stud size 516 8 mm x 3, very easy to install, universal used for car, vehicle, Rv and boat, also electrical equipment's switch..

DUAL BATTERY DISCONNECT SWITCH The master power cut off switch allows for two batteries to operate independent of one another, or for both to be in the ON or OFF position at the same time. Four position rotating switch provides Battery 1, both on, battery 2, both off alternatives. Removable rear cover insulates the rear terminals against any short circuits. 4 Removable side plates provided access for battery cables. SAVE YOUR BATTERY The battery kill switch can help you to shut down the power of battery easily and safely when not in use or storage so as to keep your vehicle from draining out of power as well as extend the life of your battery. SOLID AND COMPACT SHUT OFF SWITCH This battery disconnect isolator switch is made of PBT plastic housing, copper tin plating inner stud. Come with four stainless steel mounting screws and caps to help fix the switch tightly. The red knob is for OnOff control. Can not be removed from the switch. Stud Size 3x516 8mm. Ideal for marinevehicles applications. WIDELY APPLICATION 1-2-Both-Off, Rating 200 Amps Continuous,1000 Amps momentary at 12V DC. Can be used with 12V - 48V DC systems to isolate and secure the electrical system. Can stand alone or be locked together with other switch. Widely used for marine, boat, RV, camper, travel trailer, truck, ATV, UTV, car vehicles, battery banks and other devices. REST ASSURED TO PURCHASE We offer 30-day money-back for any reason, 12-month warranty for quality-related issues. Any problem in using our battery disconnect switch, please kindly contact us, your problem will be solved within 24 HOURS.